Cisco 819 Integrated Services Router
Hardware Installation Guide
April 5, 2013
Americas Headquarters
Cisco Systems, Inc. 170 West Tasman Drive
San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000
800 553-NETS (6387) Fax: 408 527-0883
Text Part Number: OL-23125-02
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
Cisco 819 Integrated Services Router Hardware Installation Guide
© 2011-2013 Cisco Systems, Inc. All rights reserved.
|
|
|
|
|
|
|
|
|
|
C O N T E N T S |
|||
|
|
|
Preface 5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
Objective |
5 |
|
|
|
|
|
|
|
|
|
|
|
|
Audience |
5 |
|
|
|
|
|
|
|
|
|
|
|
|
Organization |
6 |
|
|
|
|
|
|
|
|
|
|
|
|
Conventions |
|
6 |
|
|
|
|
|
|
|
|
|
|
|
Related Documentation 14 |
|
|
|
|
|
|
||||
|
|
|
Searching Cisco Documents |
14 |
|
|
|
|
|
||||
|
|
|
Obtaining Documentation and Submitting a Service Request 14 |
||||||||||
|
|
Product Overview |
|
|
|
|
|
|
|
||||
C H A P T E R |
1 |
1-1 |
|
|
|
|
|
|
|||||
|
|
|
General Description |
1-1 |
|
|
|
|
|
|
|||
|
|
|
SKU Information |
1-5 |
|
|
|
|
|
|
|||
|
|
|
Rebranding of C8xx-B and EHWIC-3G-EVDO-B 1-10 |
||||||||||
|
|
|
Hardware Features |
1-10 |
|
|
|
|
|
|
|||
|
|
|
Platform Features for Cisco 819 ISRs |
1-11 |
|
|
|
||||||
|
|
|
Antennas |
1-12 |
|
|
|
|
|
|
|
||
|
|
|
WiFi External Antenna |
1-12 |
|
|
|
|
|||||
|
|
|
Power Switch |
|
1-13 |
|
|
|
|
|
|
||
|
|
|
Reset Button |
1-13 |
|
|
|
|
|
|
|||
|
|
|
LEDs |
1-13 |
|
|
|
|
|
|
|
|
|
|
|
|
Memory |
1-17 |
|
|
|
|
|
|
|
||
|
|
|
Embedded 3G Modem |
1-18 |
|
|
|
|
|
||||
|
|
|
Embedded 4G LTE Modem |
1-18 |
|
|
|
|
|||||
|
|
|
SIM Card |
1-18 |
|
|
|
|
|
|
|
||
|
|
|
Supported Cisco Antennas and Cables |
1-19 |
|
|
|
||||||
|
|
|
Serial Port |
1-23 |
|
|
|
|
|
|
|||
|
|
|
Power Supply |
|
1-24 |
|
|
|
|
|
|
||
|
|
|
AC Power Adapter |
1-24 |
|
|
|
|
|||||
|
|
|
DC Power Adapters |
1-25 |
|
|
|
|
|||||
|
|
|
Railway Power Adapters |
1-25 |
|
|
|
|
|||||
|
|
|
Accessories |
1-25 |
|
|
|
|
|
|
|||
|
|
Installing the Router |
|
|
|
|
|
|
|
|
|||
C H A P T E R |
2 |
|
2-1 |
|
|
|
|
|
|
||||
|
|
|
Equipment, Tools, and Connections 2-2 |
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
Cisco 819 Integrated Services Router Hardware Installation Guide |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OL-23125-02 |
|
|
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
Contents
|
|
|
|
|
Items Shipped with your Router |
2-3 |
|
|
|||||||
|
|
|
|
|
Additional Items |
2-3 |
|
|
|
|
|
|
|||
|
|
|
|
|
Connections |
2-3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ethernet Devices |
2-4 |
|
|
|
|
|
|
|||
|
|
|
|
|
Installing the Router |
2-4 |
|
|
|
|
|
|
|||
|
|
|
|
|
Warnings |
2-4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Accessing the SIM Card |
2-5 |
|
|
|
|
|
||||
|
|
|
|
|
Installing Antennas |
2-6 |
|
|
|
|
|
|
|||
|
|
|
|
|
Installing a WiFi External Antenna |
|
2-7 |
|
|
||||||
|
|
|
|
|
Installing on a Table |
2-8 |
|
|
|
|
|
||||
|
|
|
|
|
Mounting on a Wall |
2-8 |
|
|
|
|
|
||||
|
|
|
|
|
Installing a DIN Rail |
2-10 |
|
|
|
|
|
||||
|
|
|
|
|
Installing the Router Ground Connection |
2-12 |
|
||||||||
|
|
|
|
|
Installing the Power Cord Retention Lock |
2-13 |
|
||||||||
|
|
|
|
|
Installing the Power Switch Lock |
2-15 |
|
|
|||||||
|
|
|
|
|
Mounting the DC Power Supply |
2-17 |
|
|
|
|
|||||
|
|
Connecting the Router |
|
|
|
|
|
|
|
||||||
C H A P T E R |
3 |
3-1 |
|
|
|
|
|
|
|||||||
|
|
|
|
|
Preparing to Connect the Router |
3-1 |
|
|
|
|
|||||
|
|
|
|
|
Preventing Damage to the Router |
3-1 |
|
|
|||||||
|
|
|
|
|
Connecting a PC, Server, or Workstation |
3-2 |
|
|
|||||||
|
|
|
|
|
Connecting an External Ethernet Switch |
3-2 |
|
|
|||||||
|
|
|
|
|
Connecting a Terminal or PC to the Console Port 3-4 |
||||||||||
|
|
|
|
|
Terminal Emulator Settings |
3-5 |
|
|
|
|
|||||
|
|
|
|
|
Connecting a Modem to the Console Port |
3-5 |
|
|
|||||||
|
|
|
|
|
Connecting the AC Adapter |
3-6 |
|
|
|
|
|
||||
|
|
|
|
|
Connecting the DC Adapter |
3-6 |
|
|
|
|
|
||||
|
|
|
|
|
Verifying Connections |
|
3-8 |
|
|
|
|
|
|
||
|
|
Initial Configuration |
|
|
|
|
|
|
|
|
|||||
C H A P T E R |
4 |
4-1 |
|
|
|
|
|
|
|
||||||
|
|
|
|
|
Cisco Configuration Professional Express |
4-1 |
|
|
|||||||
|
|
|
|
|
Cisco IOS CLI |
4-1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setup Command Facility |
4-3 |
|
|
|
|
|
|
|||
|
|
|
|
|
Verifying the Initial Configuration |
4-5 |
|
|
|
|
|||||
|
|
|
Technical Specifications |
|
|
|
|
|
|
|
|||||
A P P E N D I X |
|
A |
A-1 |
|
|
|
|
|
|
||||||
|
|
|
|
|
Router Specifications |
A-1 |
|
|
|
|
|
|
|||
|
|
|
|
Cisco 819 Integrated Services Router Hardware Installation Guide |
|
|
|
||||||||
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
OL-23125-02 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
Contents
Mean Time Between Failure Ground Benign Environment A-5
Supported Power Adapters A-6
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
3 |
|
|
|
Contents
Cisco 819 Integrated Services Router Hardware Installation Guide
4 |
OL-23125-02 |
|
|
Preface
This preface describes the objectives, audience, organization, and conventions of this guide and describes related documents that have additional information. It contains the following sections:
•Objective, page 5
•Audience, page 5
•Organization, page 6
•Conventions, page 6
•Related Documentation, page 14
•Searching Cisco Documents, page 14
•Obtaining Documentation and Submitting a Service Request, page 14
Objective
This guide provides an overview and explains how to install, connect, and perform initial configuration for the Cisco 819 ISR. Some information may not apply to your particular router model.
For warranty, service, and support information, see the “Cisco One-Year Limited Hardware Warranty Terms” section in Readme First for the Cisco 800 Series Integrated Services Routers that was shipped with your router.
Audience
This guide is intended for Cisco equipment providers who are technically knowledgeable and familiar with Cisco routers and Cisco IOS software and features.
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
5 |
|
|
|
Preface
Organization
This guide is organized into the following chapters and appendix.
Chapter |
Name |
Description |
|
|
|
Chapter 1 |
Chapter 1, “Product Overview” |
Describes the router models and the |
|
|
hardware features available. |
|
|
|
Chapter 2 |
Chapter 2, “Installing the Router” |
Lists the items shipped with the router, the |
|
|
equipment and tools necessary for |
|
|
installing the router, the safety warnings |
|
|
and guidelines, and the procedures for |
|
|
installing the router. |
|
|
|
Chapter 3 |
Chapter 3, “Connecting the Router” |
Describes typical connections for the |
|
|
router, procedures for connecting the |
|
|
router to various devices, and how to |
|
|
verify the connections. |
|
|
|
Chapter 4 |
Chapter 4, “Initial Configuration” |
Provides the procedures for initially |
|
|
configuring the router settings. |
|
|
|
Appendix A |
Appendix A, “Technical Specifications” |
Provides the router, port, and cabling |
|
|
specifications. |
|
|
|
Conventions
This section describes the conventions used in this guide.
Note Means reader take note. Notes contain helpful suggestions or references to additional information and material.
Caution This symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
Tip Means the following information will help you solve a problem. The tip information might not be troubleshooting or even an action, but could be useful information.
Cisco 819 Integrated Services Router Hardware Installation Guide
6 |
OL-23125-02 |
|
|
Preface
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
7 |
|
|
|
Preface
Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning! VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.
SPARA DESSA ANVISNINGAR
Cisco 819 Integrated Services Router Hardware Installation Guide
8 |
OL-23125-02 |
|
|
Preface
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
9 |
|
|
|
Preface
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Cisco 819 Integrated Services Router Hardware Installation Guide
10 |
OL-23125-02 |
|
|
Preface
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
11 |
|
|
|
Preface
Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products. Statement 371
Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378
Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Statement 1015
Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Cisco 819 Integrated Services Router Hardware Installation Guide
12 |
OL-23125-02 |
|
|
Preface
Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe personal injury or can damage the unit. Statement 1031
Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033
Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035
Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036
Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037
Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038
Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046
Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052
Warning No user-serviceable parts inside. Do not open. Statement 1073
Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
13 |
|
|
|
Preface
Warning Read the installation instructions before connecting the system to the power source. Statement 1004
Warning Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed. Statement 1077
Warning Hot surface. Statement 1079
Related Documentation
•Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
•Cisco IOS Release Notes
•Cisco IOS Quality of Service Solutions Command Reference, Release 12.4T
•Cisco IOS Security Configuration Guide, Release 12.4T
•Cisco IOS Security Command Reference, Release 12.4T
•Cisco CP Express User’s Guide
Searching Cisco Documents
To search an HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple). In most browsers, the option to search whole words only, invoke case sensitivity, or search forward and backward is also available.
To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document. Use the Full Reader Search window to search multiple PDF files simultaneously and to change case sensitivity and other options. Adobe Reader’s online help has more information about how to search PDF documents.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Cisco 819 Integrated Services Router Hardware Installation Guide
14 |
OL-23125-02 |
|
|
Preface
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
15 |
|
|
|
Preface
Cisco 819 Integrated Services Router Hardware Installation Guide
16 |
OL-23125-02 |
|
|
C H A P T E R 1
Product Overview
This chapter provides an overview of the features available for the Cisco 819 and Cisco 819H Integrated Services Routers (ISRs) and contains the following sections:
•General Description, page 1-1
•SKU Information, page 1-5
•Hardware Features, page 1-10
Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.
General Description
The Cisco 819 Integrated Services Router, part of the Cisco Integrated Services Routers Generation 2 (ISR G2) Family designed in compact hardened and non-hardened form factors, is the smallest Cisco IOS Software router with support for integrated fourth-generation (4G LTE) and third-generation (3G) wireless WAN (mobile broadband backhaul). The 3G Cisco 819 now supports Dual 802.11 a/b/g/n radios WiFi. The Cisco 819 ISR machine-to-machine gateway provides a rapidly deployable, highly available, reliable, and secure solution into machine-to-machine applications for financial, telemetry, utility, retail, industrial automation, and transportation with comprehensive management capability. Transparently integrated into Cisco IOS Software as an enterprise-class feature, the Cisco 819 Hardened ISR provides highly secure data, voice, and video communications to stationary and mobile network nodes across wired and wireless links.
Available in both non-hardened (Cisco 819G) and hardened (Cisco 819HG) versions, the Cisco 819 supporting 4G LTE and 3G wireless WAN (WWAN) speeds offers a cost-effective, rapidly deployable, reliable, and secure primary or backup solution. With support for industrial-grade components, the hardened Cisco 819HG extends the ISR machine-to-machine gateway footprint and provides the flexibility for deployment in many different stationary and mobile environments where space, heat dissipation, exposure to extreme temperatures, harsher environments, and low power consumption are critical factors. For mobile applications, Mobile IP delivers transparent roaming across multiple wireless networks capable of covering wide geographic areas.
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
1-1 |
|
|
|
Chapter 1 Product Overview
General Description
The Cisco 819 ISR is a standard form factor with a commercial operating range. The 3G Cisco 819 ISRs support the 3G speeds (High-Speed PacketAccess Plus [HSPA+] enabling up to 4G speeds and Evolution Data Optimized [EVDO Rev A]). They are backward-compatible with High-Speed Packet Access (HSPA), Universal Mobile Telecommunications Service (UMTS), Enhanced Data Rates for Global Evolution (EDGE), General Packet Radio Service (GPRS), and EVDO Rev 0/1xRTT.
The 4G LTE C819 supports the latest Third-Generation Partnership Project (3GPP) Release 8 LTE standards. The Cisco 4G multimode LTE WWAN C819 provides persistent and reliable LTE connectivity with fallback and transparent handoff to earlier technologies. The Cisco 819HG-4G and Cisco 819G-4G support multimode 4G LTE and have embedded Sierra Wireless multimode modem.
The Cisco 819 ISR is a desktop form factor with built-in wall-mount features, floor mount, and DIN rail mount features in selected SKUs. These routers are powered by an external AC power or optional DC adapter. Figure 1-1 shows the Cisco 819HG ISR.
Beginning with IOS release 15.2(4)M1, the new 3G Cisco 819HGW and Cisco 819HWD ISRs support WiFi radios with a higher memory density and a new barrel-type power connector. A Wireless Local Area Network (WLAN) implements a flexible data communication system frequently augmenting rather than replacing a wired LAN within a building or campus. WLANs use radio frequency to transmit and receive data over the air, minimizing the need for wired connections. Figure 1-2 shows the Cisco 819HGW ISR.
The WLAN for 3G Cisco 819HGW and Cisco 819HWD ISRs have the following additional features:
•Dual 802.11 a/b/g/n radios
•External WiFi antenna
•WLAN LED
Note Cisco 819 is used to refer to Cisco 819HG, Cisco 819G, Cisco 819H, Cisco 819HGW, Cisco 819HWD, Cisco 819HG-4G, and Cisco 819G-4G ISRs unless specifically called out otherwise.
Figure 1-1 Cisco 819HG Integrated Services Router
283010
Cisco 819 Integrated Services Router Hardware Installation Guide
1-2 |
OL-23125-02 |
|
|
Chapter 1 Product Overview
General Description
Figure 1-2 Cisco 819HGW Integrated Services Router
285479
Figure 1-3 shows the front panel details of the Cisco 819HG ISR.
Figure 1-3 Cisco 819HG ISR Front Panel
5 |
8 |
|
|
|
|
|
|
|
|
|
245547 |
1 |
2 |
3 |
4 |
6 |
7 |
9 |
10 |
11 |
12 |
1 |
3G main antenna |
7 |
FE ports |
|
|
|
|
2 |
LEDs |
8 |
GE WAN port |
|
|
|
|
3 |
Reset button |
9 |
Console/Aux port |
|
|
|
|
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
1-3 |
|
|
|
Chapter 1 Product Overview
General Description
4 |
3G mini-USB diagnostic port |
10 |
5 VDC molex power input |
|
|
|
|
5 |
Diversity/GPS antenna |
11 |
Power switch |
|
|
|
|
6 |
12-in-1 serial port |
12 |
Ground |
|
|
|
|
Figure 1-4 shows the front panel details of the Cisco 819HGW ISR.
Figure 1-4 Cisco 819HGW ISR Front Panel
5 |
8 |
|
|
|
|
|
|
|
|
|
344077 |
1 |
2 |
3 |
4 |
6 |
7 |
9 |
10 |
11 |
12 |
1 |
3G main antenna |
7 |
FE ports |
|
|
|
|
2 |
LEDs |
8 |
GE WAN port |
|
|
|
|
3 |
Reset button |
9 |
Console/Aux port |
|
|
|
|
4 |
3G mini-USB diagnostic port |
10 |
5 VDC barrel-type power input |
|
|
|
|
5 |
Diversity/GPS antenna |
11 |
Power switch |
|
|
|
|
6 |
12-in-1 serial port |
12 |
Ground |
|
|
|
|
Cisco 819 Integrated Services Router Hardware Installation Guide
1-4 |
OL-23125-02 |
|
|
Chapter 1 Product Overview
SKU Information
Figure 1-5 shows the front panel details of the Cisco 819 4G LTE ISR.
Figure 1-5 Cisco 819 4G LTE ISR Front Panel
|
|
|
|
5 |
|
8 |
|
|
12 |
|
|
|
|
|
|
|
|
|
285447 |
1 |
2 |
3 |
4 |
6 |
7 |
9 |
10 |
11 |
13 |
1 |
Antenna connector—M0/MAIN |
8 |
GE WAN port |
|
|
|
|
2 |
LEDs |
9 |
Console/Aux port |
|
|
|
|
3 |
Reset button |
10 |
Power input |
|
|
|
|
4 |
4G/3G port |
11 |
Power switch |
|
|
|
|
5 |
Antenna connector—M1/DIV |
12 |
Active GPS antenna connector |
|
|
|
|
6 |
Serial port |
13 |
Ground |
|
|
|
|
7 |
FE ports |
|
|
|
|
|
|
SKU Information
Table 1-1 lists the different 3G SKUs available for the Cisco 819HG and Cisco 819G ISRs. All SKUs support external antenna.
Note WLAN is not supported.
|
|
Table 1-1 |
Supported 3G SKUs for Cisco 819HG and Cisco 819G ISRs |
|||||
|
|
|
|
|
|
|||
|
|
SKU ID |
|
Description |
||||
|
|
|
|
|
|
|||
|
|
C819HG+7-K9 |
|
Compact Hardened 3G IOS Router with Global HSPA + Release 7 based on |
||||
|
|
|
|
MC8705 |
||||
|
|
|
|
|
|
|||
|
|
C819HG-U-K9 |
|
Compact Hardened 3G IOS Router with GLOBAL HSPA Release 6 based on |
||||
|
|
|
|
MC8795V |
||||
|
|
|
|
|
|
|||
|
|
C819HG-V-K9 |
|
Compact Hardened 3G IOS Router with Verizon EVDO Rev A based on |
||||
|
|
|
|
MC5728V |
||||
|
|
|
|
|
|
|||
|
|
C819HG-S-K9 |
|
Compact Hardened 3G IOS Router with Sprint EVDO Rev A based on |
||||
|
|
|
|
MC5728V |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Cisco 819 Integrated Services Router Hardware Installation Guide |
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
OL-23125-02 |
|
|
|
1-5 |
|
||
|
|
|
|
|
||||
Chapter 1 Product Overview
SKU Information
Table 1-1 |
Supported 3G SKUs for Cisco 819HG and Cisco 819G ISRs(continued) |
|
|
|
|
SKU ID |
|
Description |
|
|
|
C819HG-B-K9 |
|
Compact Hardened 3G IOS Router with Bharat generic EVDO Rev A based |
|
|
on MC5728V |
|
|
|
C819G+7-K9 |
|
C ompact Non-hardened 3G IOS Router with Global HSPA + Release 7 |
|
|
based on MC8705 |
|
|
|
C819G-U-K9 |
|
Compact Non-hardened 3G IOS Router with GLOBAL HSPA Release 6 |
|
|
based on MC8795V |
|
|
|
C819G-V-K9 |
|
Compact Non-hardened 3G IOS Router with Verizon EVDO Rev A based on |
|
|
MC5728V |
|
|
|
C819G-S-K9 |
|
Compact Non-hardened 3G IOS Router with Sprint EVDO Rev A based on |
|
|
MC5728V |
|
|
|
C819G-B-K9 |
|
Compact Non-hardened 3G IOS Router with Bharat generic EVDO Rev A |
|
|
based on MC5728V |
|
|
|
Cisco 819 Integrated Services Router Hardware Installation Guide
1-6 |
OL-23125-02 |
|
|
Chapter 1 Product Overview
SKU Information
Table 1-2 lists the different SKUs available for the Cisco 819HGW, Cisco 819H, and Cisco 819HWD ISRs.
Table 1-2 |
Supported SKUs for Cisco 819HGW, Cisco 819H, and Cisco 819HWD ISRs |
|||
|
|
|
|
|
|
|
|
WiFi External Antenna |
|
SKU ID |
|
WLAN ID |
Support |
Description |
|
|
|
|
|
C819HGW+7-E-K9 |
AP802H-AGN-E-K9 |
Yes |
Cisco 819 Secure Hardened M2M |
|
|
|
|
|
GW (non-US) 3.7G HSPA + Release |
|
|
|
|
7 with SMS/GPS and Dual WiFi |
|
|
|
|
Radio with ETSI |
|
|
|
|
|
C819HGW+7-N-K9 |
AP802H-AGN-N-K9 |
Yes |
Cisco 819 Secure Hardened M2M |
|
|
|
|
|
GW (non-US) 3.7G HSPA + Release |
|
|
|
|
7 with SMS/GPS and Dual WiFi |
|
|
|
|
Radio with ANZ |
|
|
|
|
|
C819HGW+7-A-A-K9 |
AP802H-AGN-A-K9 |
Yes |
Cisco 819 Secure Hardened M2M |
|
|
|
|
|
GW (North America) 3.7G HSPA + |
|
|
|
|
Release 7 with SMS/GPS and Dual |
|
|
|
|
WiFi Radio with FCC for ATT |
|
|
|
|
|
C819HGW-V-A-K9 |
AP802H-AGN-A-K9 |
Yes |
Cisco 819 Secure Hardened Router |
|
|
|
|
|
for Verizon EV-DO Rev A with |
|
|
|
|
SMS/GPS and Dual WiFi Radio with |
|
|
|
|
FCC |
|
|
|
|
|
C819HGW-S-A-K9 |
AP802H-AGN-A-K9 |
Yes |
Cisco 819 Secure Hardened Router |
|
|
|
|
|
for Sprint EV-DO Rev A with |
|
|
|
|
SMS/GPS and Dual WiFi Radio with |
|
|
|
|
FCC |
|
|
|
|
|
C819H-K9 |
|
— |
— |
Cisco 819 Secure Hardened Router |
|
|
|
|
with Serial |
|
|
|
|
WLAN and 3G are not supported |
|
|
|
|
|
C819HWD-E-K9 |
AP802H-AGN-E-K9 |
Yes |
Cisco 819 Secure Hardened Router |
|
|
|
|
|
and Dual WiFi Radio with ETSI |
|
|
|
|
3G is not supported |
|
|
|
|
|
C819HWD-A-K9 |
AP802H-AGN-A-K9 |
Yes |
Cisco 819 Secure Hardened Router |
|
|
|
|
|
and Dual WiFi Radio with FCC |
|
|
|
|
3G is not supported |
|
|
|
|
|
Cisco 819 Integrated Services Router Hardware Installation Guide
|
OL-23125-02 |
1-7 |
|
|
|
Chapter 1 Product Overview
SKU Information
Table 1-3 lists the different 4G LTE SKUs available for the Cisco 819HG and Cisco 819G ISRs.
Table 1-3 |
Supported 4G LTE SKUs for the Cisco 819HG-4G and Cisco 819G-4G ISRs |
|
|||
|
|
|
|
|
|
SKU ID |
|
Mode |
Operating Regions |
Frequency Band |
Description |
|
|
|
|
|
|
C819HG-4G-V-K9 |
LTE—DOrA |
North America |
700 MHz (band 13) for LTE |
Compact Hardened Cisco |
|
|
|
|
|
800/1900 MHz for CDMA |
819 router with |
|
|
|
|
multimode LTE feature |
|
|
|
|
|
1xRTT, 1xEVDO Rev A |
|
|
|
|
|
dedicated to Verizon |
|
|
|
|
|
|
|
|
|
|
|
|
Wireless networks. This |
|
|
|
|
|
comes with a Sierra |
|
|
|
|
|
Wireless MC7750 |
|
|
|
|
|
modem. |
|
|
|
|
|
|
C819G-4G-V-K9 |
LTE—DOrA |
North America |
700 MHz (band 13) for LTE |
Compact Non-hardened |
|
|
|
|
|
800/1900 MHz for CDMA |
Cisco 819 router with |
|
|
|
|
multimode LTE feature |
|
|
|
|
|
1xRTT, 1xEVDO Rev A |
|
|
|
|
|
dedicated to Verizon |
|
|
|
|
|
|
|
|
|
|
|
|
Wireless networks. This |
|
|
|
|
|
comes with a Sierra |
|
|
|
|
|
Wireless MC7750 |
|
|
|
|
|
modem. |
|
|
|
|
|
|
C819HG-4G-A-K9 |
LTE—HSPA+/ |
North America |
700 MHz(band 17)/AWS(band |
Compact Hardened Cisco |
|
|
|
HSPA/UMTS/ |
|
4)/2100MHz(band 1) for LTE |
819 router with |
|
|
|
|
multimode LTE feature |
|
|
|
EDGE/GPRS |
|
800/850/1900/2100 MHz for |
|
|
|
|
dedicated to AT&T |
||
|
|
|
UMTS/ HSPA+/HSPA |
||
|
|
|
|
Wireless networks. This |
|
|
|
|
|
850/900/1800/1900 MHz for |
|
|
|
|
|
comes with a Sierra |
|
|
|
|
|
GSM/EDGE/GPRS |
Wireless MC7700 |
|
|
|
|
|
modem. |
|
|
|
|
|
|
C819G-4G-A-K9 |
LTE—HSPA+/ |
North America |
700 MHz(band 17)/AWS(band |
Compact Non-hardened |
|
|
|
HSPA/UMTS/ |
|
4)/2100MHz(band 1) for LTE |
Cisco 819 router with |
|
|
|
|
multimode LTE feature |
|
|
|
EDGE/GPRS |
|
800/850/1900/2100 MHz for |
|
|
|
|
dedicated to AT&T |
||
|
|
|
UMTS/ HSPA+/HSPA |
||
|
|
|
|
Wireless networks. This |
|
|
|
|
|
850/900/1800/1900 MHz for |
|
|
|
|
|
comes with a Sierra |
|
|
|
|
|
GSM/EDGE/GPRS |
Wireless MC7700 |
|
|
|
|
|
modem. |
|
|
|
|
|
|
Cisco 819 Integrated Services Router Hardware Installation Guide
1-8 |
OL-23125-02 |
|
|
Loading...