Cisco Systems 5000 Series User Manual

Size:
9.61 Mb
Download

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Cisco Nexus 5000 Series Hardware

Installation Guide

November 2008

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706USAhttp://www.cisco.com Tel: 408526-4000

800 553-NETS(6387) Fax: 408527-0883

Text Part Number: OL-15902-01

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequencyenergy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequencyenergy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

Turn the television or radio antenna until the interference stops.

Move the equipment to one side or the other of the television or radio.

Move the equipment farther away from the television or radio.

Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMEDSUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco StadiumVision, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn is a service mark; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0804R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco Nexus 5000 Series Hardware Installation Guide

© 2008 Cisco Systems, Inc. All rights reserved.Send documentation comments to nexus5kdocs@cisco.com

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

 

 

 

 

 

 

C O N T E N T S

 

 

iii

 

 

 

 

 

 

 

 

 

 

Preface vii

 

 

 

 

 

 

 

 

 

 

Audience

vii

 

 

 

 

 

 

 

 

 

Organization

vii

 

 

 

 

 

 

 

 

Conventions

 

viii

 

 

 

 

 

 

 

 

Related Documentation

i-xiv

 

 

Obtaining Documentation, Obtaining Support, and Security Guidelines i-xiv

 

Product Overview 1-1

 

 

 

 

 

C H A P T E R 1

 

 

 

 

 

 

 

Nexus 5020 Switch

1-1

 

 

 

 

 

 

Features

1-1

 

 

 

 

 

 

 

 

Chassis

 

1-2

 

 

 

 

 

 

 

 

Expansion Modules

1-5

 

 

 

 

 

 

Fibre Channel Plus Ethernet Expansion Module 1-5

 

 

Ethernet Expansion Module 1-6

 

 

N5K-M1008 1-7

 

 

 

 

 

 

Ports

1-8

 

 

 

 

 

 

 

 

Power Supply

1-9

 

 

 

 

 

 

 

Fan Module

1-10

 

 

 

 

 

 

 

LED Descriptions

1-12

 

 

 

 

 

 

Supported SFP Transceivers 1-14

 

 

SFP+ Transceivers

1-14

 

 

 

 

 

SFP+ Copper Cables

1-14

 

 

 

 

 

SFP Fiber Channel Transceivers 1-15

 

 

Nexus 5010 Switch

1-15

 

 

 

 

 

 

Features

1-16

 

 

 

 

 

 

 

Chassis

 

1-16

 

 

 

 

 

 

 

 

Expansion Modules

1-20

 

 

 

 

 

N5K-M1404 1-20

 

 

 

 

 

 

N5K-M1600 1-21

 

 

 

 

 

 

N5K-M1008 1-22

 

 

 

 

 

 

Ports

1-23

 

 

 

 

 

 

 

 

Power Supply

1-25

 

 

 

 

 

 

Fan Module

1-26

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-15902-01

 

 

 

 

 

 

 

iii

 

 

 

 

 

 

 

 

 

 

Contents

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

LED Descriptions

1-27

 

 

 

Port Level LED’s

1-28

 

 

 

Supported SFP Transceivers 1-28

 

 

 

SFP+ Transceivers

1-29

 

 

 

SFP+ Copper Cables 1-29

 

 

 

SFP Fiber Channel Transceivers

1-29

 

 

Installing the Cisco Nexus 5000 Switch

 

 

C H A P T E R 2

2-1

 

 

Preparing for Installation

2-2

 

 

 

Installation Options 2-2

 

 

 

Airflow Considerations

2-2

 

 

 

Chassis Weight

2-2

 

 

 

 

Installation Guidelines

2-3

 

 

 

Required Equipment

2-4

 

 

 

Unpacking and Inspecting the Switch

2-4

 

 

Installing the Cisco Nexus 5020 Chassis in a Cabinet or Rack

2-5

 

Installing the Cisco Nexus 5010 Chassis in a Cabinet or Rack

2-8

 

Grounding the System

2-10

 

 

Proper Grounding Practices

2-10

 

 

Preventing Electrostatic Discharge Damage

2-12

Establishing the System Ground

2-14

 

 

Required Tools and Equipment

2-14

 

 

Grounding the Chassis

2-15

 

 

 

 

Starting the Switch

2-17

 

 

 

 

Removing and Installing Components

2-18

 

Removing and Installing Expansion Modules 2-19

Installing an Expansion Module

2-19

 

Removing an Expansion Module

2-20

Removing and Installing Power Supplies

2-21

Removing a Power Supply

2-21

 

 

Installing a Power Supply

 

2-22

 

 

Removing and Installing the Fan Module

2-23

Removing a Fan Module

2-24

 

 

Installing a Fan Module

2-25

 

 

Removing the Cisco Nexus 5000 Switch 2-25

Repacking the Cisco Nexus 5000 Switch for Return Shipment 2-26

Cisco Nexus 5000 Series Hardware Installation Guide

 

iv

OL-15902-01

 

 

 

Contents

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

C H A P T E R 3

Connecting the Cisco Nexus 5000 Switch

3-1

 

Preparing for Network Connections 3-2

 

 

Connecting to the Console Port

3-2

 

 

Connecting to the Ethernet Connector Port

3-3

 

Connecting to an Ethernet Port

3-4

 

Removing and Installing SFP+ Transceivers

3-4

 

Installing an SFP+ Transceiver

3-4

 

 

Removing an SFP+ Transceiver

3-4

 

 

Removing and Installing Cables into SFP+ Transceivers 3-6

Installing a Cable into an SFP+ Transceiver

3-6

Removing a Cable from an SFP+ Transceiver

3-6

Maintaining SFP+ Transceivers and Cables

3-7

 

Connecting to a Fibre Channel Port 3-7

 

 

 

Removing and Installing SFP Transceivers

3-7

 

Installing an SFP Transceiver

3-7

 

 

Removing an SFP Transceiver

3-8

 

 

 

 

 

Removing and Installing Cables into SFP Transceivers

3-9

 

 

 

 

 

 

Installing a Cable into an SFP Transceiver

3-9

 

 

 

 

 

 

 

Removing a Cable from an SFP Transceiver

3-10

 

 

 

 

 

 

 

Maintaining SFP Transceivers and Fiber-Optic Cables

3-11

 

 

 

 

 

Cabinet and Rack Requirements

 

 

 

 

 

 

A P P E N D I X

A

A-1

 

 

 

 

 

 

 

 

General Requirements for Cabinets and Racks

A-1

 

 

 

 

 

 

 

Requirements Specific to Perforated Cabinets

A-2

 

 

 

 

 

 

 

Requirements Specific to Solid-Walled Cabinets

A-3

 

 

 

 

 

 

 

Requirements Specific to Standard Open Racks

A-3

 

 

 

 

 

 

 

Cable Management Guidelines

A-3

 

 

 

 

 

 

 

Switch Specifications

 

 

 

 

 

 

 

A P P E N D I X

B

B-1

 

 

 

 

 

 

 

 

 

Expansion Module Specifications

B-2

 

 

 

 

 

 

 

 

Power Specifications

B-2

 

 

 

 

 

 

 

 

 

Specifications for the Cisco Nexus 5020 Power Supply

B-2

 

 

 

 

 

 

Specifications for the Cisco Nexus 5010 Power Supply

B-3

 

 

 

 

 

 

Power Supply LED Indicators

B-3

 

 

 

 

 

 

 

 

Transceiver Specifications B-4

 

 

 

 

 

 

 

 

 

Environmental Conditions and Power Requirement Specifications for SFP+ Transceivers

 

B-4

 

 

 

General Specifications for Cisco Fibre Channel SFP Transceivers B-4

 

 

 

 

 

 

Environmental Conditions and Power Requirements Specification for SFP Transceivers

B-5

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-15902-01

 

 

 

 

 

 

 

v

 

 

 

 

 

 

 

 

 

 

Contents

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

A P P E N D I X

C

Accessory Kit for the Cisco Nexus 5020 Switch

C-1

 

 

Accessory Kit for the Cisco Nexus 5010 Switch

C-1

 

 

Console Cable

C-2

 

 

 

 

 

Cable RJ-45 Connector Pinouts

C-2

 

 

 

Console Port

C-3

 

 

 

 

 

 

Console Port Pinouts

C-3

 

 

 

 

Supported Power Cords and Plugs

C-4

 

 

 

Power Cords

C-4

 

 

 

 

 

AC Power Cord Illustrations

C-5

 

 

 

Jumper Power Cord

C-10

 

 

 

 

 

Site Preparation Checklist

 

 

 

A P P E N D I X

D

D-1

 

 

 

 

Contact and Site Information D-3

 

 

 

 

Chassis and Module Information D-4

 

 

 

Overview E-1

 

 

 

 

 

A P P E N D I X

E

 

 

 

 

 

 

 

SNMP Traps

E-1

 

 

 

 

Switch Hardware Best Practices

E-1

Installation Best Practices

E-2

Initialization Best Practices

E-2

Switch Operation Best Practices E-2

E-2

I N D E X

Cisco Nexus 5000 Series Hardware Installation Guide

 

vi

OL-15902-01

 

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Preface

This preface describes the audience, organization, and conventions of the Cisco Nexus 5000 Series Hardware Installation Guide. It also provides information on how to obtain related documentation.

Audience

To use this installation guide, you must be familiar with electronic circuitry and wiring practices and preferably be an electronic or electromechanical technician.

Organization

This guide is organized as follows:

Chapter

Title

Description

 

 

 

Chapter 1

Product Overview

Provides an overview of the Cisco Nexus 5000 switches and

 

 

their components.

 

 

 

Chapter 2

Installing the Cisco

Describes how to install the Cisco Nexus 5000 switches, and

 

Nexus 5000 Switch

how to install modules, power supplies, and fan assemblies.

 

 

 

Chapter 3

Connecting the

Describes how to connect the Cisco Nexus 5000 switches,

 

Cisco Nexus 5000

including the modules.

 

Switch

 

 

 

 

Appendix A

Cabinet and Rack

Provides guidelines for selecting an enclosed cabinet, the

 

Installation

procedure for installing a switch using the optional and EIA

 

 

Shelf Bracket Kit.

 

 

 

Appendix B

Technical

Lists specifications for the Cisco Nexus 5000 switches and

 

Specifications

components including modules, power supplies, and

 

 

transceivers.

 

 

 

Appendix C

Cable and Port

Lists cable and port specifications for the Cisco Nexus 5000

 

Specifications

switches.

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

vii

 

Preface

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Chapter

Title

Description

 

 

 

Appendix D

Site Planning and

Provides site planning and maintenance records.

 

Maintenance

 

 

Records

 

 

 

 

Appendix E

Troubleshooting

Provides installation troubleshooting information for the Cisco

 

Hardware

Nexus 5000 switches.

 

Components

 

 

 

 

Conventions

This document uses the following conventions for notes, cautions, and safety warnings.

Notes and Cautions contain important information that you should be aware of.

Note Meansreader take note. Notes contain helpful suggestions or references to material that are not covered in the publication.

Caution Meansreader be careful. You are capable of doing something that might result in equipment damage or loss of data.

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, can cause physical injuries. A warning symbol precedes each warning statement.

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Cisco Nexus 5000 Series Hardware Installation Guide

 

viii

OL-15902-01

 

 

 

Preface

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vousavec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,référez-vousau numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

ix

 

Preface

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-secom as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning! VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

Cisco Nexus 5000 Series Hardware Installation Guide

 

x

OL-15902-01

 

 

 

Preface

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-secom as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

xi

 

Preface

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Cisco Nexus 5000 Series Hardware Installation Guide

 

xii

OL-15902-01

 

 

 

Preface

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

xiii

 

Preface

Related Documentation

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Related Documentation

The documentation set for the Cisco Nexus 5000 Series includes the following documents:

Cisco Nexus 5000 Series Release Notes for NX-OSReleases

Cisco Nexus 5000 Series Fabric Manager Configuration Guide

Cisco Nexus 5000 Series Fabric Manager Online Help

Cisco Nexus 5000 Series CLI Configuration Guide

Cisco Nexus 5000 Series Command Reference

Cisco Nexus 5000 Series MIB Quick Reference

Cisco Nexus 5000 Series System Messages Guide

Cisco Nexus 5000 Series Troubleshooting Guide

Cisco Nexus 5000 Series XML Management Interface Guide

Cisco Nexus 5000 Series Hardware Installation Guide

Regulatory Compliance and Safety Information for the Cisco Nexus 5000 Series

Obtaining Documentation, Obtaining Support, and Security

Guidelines

For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Cisco Nexus 5000 Series Hardware Installation Guide

 

xiv

OL-15902-01

 

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

C H A P T E R 1

Product Overview

This chapter describes the Nexus 5000 series switches and contains these sections:

Nexus 5020 Switch, page 1-1

Nexus 5010 Switch, page 1-15

Nexus 5020 Switch

This section describes the Cisco Nexus 5020 switch and its components. This section includes the following topics:

Features, page 1-1

Chassis, page 1-2

Ports, page 1-8

Expansion Modules, page 1-5

Power Supply, page 1-9

Fan Module, page 1-10

LED Descriptions, page 1-12

Supported SFP Transceivers, page 1-14

Features

The Cisco Nexus 5020 switch is a 2 RU, top-of-rackswitch that provides Ethernet and Fibre Channel consolidation in a single physical cable. The Fibre Channel over Ethernet (FCoE) protocol is used to consolidate Ethernet and Fibre Channel traffic onto the same physical connection between the server and the switch. As atop-of-rackswitch, all the servers in the rack connect to the Cisco Nexus 5020 switch, and it connects to the LAN or SAN.

The Cisco Nexus 5020 switch is a part of a family of switches that provide 10-GigabitEthernet and FCoE ports and both10-GigabitEthernet and native1-,2-,and4-GbpsFibre Channel ports. The switches provide consolidated I/O connectivity to both production Ethernet LANs and Fibre Channel SANs in acost-effective,high-performance,low-latencyEthernet switch.

The Cisco Nexus 5020 switch has the following features:

Forty fixed10-GigabitEthernet server connection ports on the back of the switch

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

1-1

 

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Two slots for optional 10-Gigabitexpansion modules or Fibre Channel interfaces on the back of the switch

Two slots on the front of the switch for hot swap-capablepower supplies

Five slots on the front of the switch for hot swap-capablefan modules, each of which houses two fans, that providefront-to-backcooling for the switch

Chassis

The Cisco Nexus 5020 chassis is 2 RU (3.47 inches) tall, 17.3 inches wide, and 30.0 inches deep. It is designed to be mounted in a standard 19-inchrack. The switch has two power supplies and five fans modules on the front of the switch. Ports are at the rear of the switch. The airflow is front to back.Figure 1-1 shows the front of the Cisco Nexus 5020 switch.

Figure 1-1Cisco Nexus 5020 Switch Front View

1

2

1

Two power supplies

2

Five fan modules

 

 

 

 

186260

Figure 1-2 shows aclose-upview of the front of the switch.

Cisco Nexus 5000 Series Hardware Installation Guide

1-2

OL-15902-01

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Figure 1-2

Cisco Nexus 5020 Switch Front View Close-up

 

 

1

2

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

186261

1

Two power supplies

3

System status LED

 

 

 

 

2

Five fan modules

 

 

 

 

 

 

The rear of the Cisco Nexus 5020 chassis has 40 fixed 10-GigabitEthernet ports, 2 slots for optional expansion modules, an Ethernet connector with 2cross-connectports and 2 management ports, a console port, and 2 AC power connectors.Figure 1-3 shows the rear of the Cisco Nexus 5020 switch.

Figure 1-3Cisco Nexus 5020 Switch Rear View

1

2

3 4

5

6

186265

1

System status LED

4

40 fixed 10-GigabitEthernet ports

 

 

 

 

2

Ethernet connector with two cross-connect

5

Expansion modules, shown here with two

 

ports on the left (top and bottom), and two

 

4-portFibre Channel plus4-port10-Gigabit

 

network management ports on the right (top

 

Ethernet expansion modules

 

and bottom)

 

 

 

 

 

 

3

Console port

6

AC power connectors

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

1-3

 

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Figure 1-4 shows aclose-upview of the rear of the Cisco Nexus 5020 chassis.

Figure 1-4Cisco Nexus 5020 Switch Rear ViewClose-up

5

1

7

 

2

3

4

6

186263

1

System status LED

4

Slot 1, with 40 fixed 10-GigabitEthernet ports

 

 

 

(highlighted in red).

 

 

 

 

2

Ethernet connector with two cross-connect

5

Slot 2 for an optional expansion module;

 

ports on left side, and two network

 

shown here with a 4-portFibre Channel plus

 

management1 (top) and management2

 

4-port10-GigabitEthernet expansion module

 

(bottom) ports on the right side

 

 

 

 

 

 

3

Console port

6

Slot 3 for an optional expansion module;

 

 

 

shown here with a 4-portFibre Channel plus

 

 

 

4-port10-GigabitEthernet expansion module

 

 

 

 

The Ethernet connector port exposes four Ethernet ports that are in a 2x2 stacked RJ-45jack.Figure 1-5 shows aclose-upview of the Ethernet connector port.

Figure 1-5Ethernet Connector Port

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

186385

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Internal cross connect ports

 

 

 

 

 

2

Network management ports

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1-4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-15902-01

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Table 1-1 lists the LED descriptions for all Ethernet LEDs.

Table 1-1

Ethernet LED Descriptions

 

 

 

 

 

LED

 

Status

Description

 

 

 

 

Left

 

Off

No link

 

 

 

 

 

 

Solid green

Physical link

 

 

 

 

Right

 

Off

No activity

 

 

 

 

 

 

Blinking green

Activity

 

 

 

 

Expansion Modules

Expansion modules allow Cisco Nexus 5000 switches to be configured as cost-effective10-GigabitEthernet switches and as I/O consolidation platforms with native Fibre Channel connectivity. The Cisco Nexus 5020 switch has two slots that can be used for the following optional expansion modules:

Fibre Channel plus Ethernet expansion module with four 10-GigabitEthernet Cisco Data Center Ethernet and FCoE ports and four1-,2-,and4-GbpsFibre Channel ports

Ethernet expansion module with six ports of 10-GigabitEthernet Cisco Data Center Ethernet and FCoE

The chassis supports hot swapping of the expansion modules.

Fibre Channel Plus Ethernet Expansion Module

The Fibre Channel plus Ethernet expansion module supports four SFP+ transceiver modules and four 1-,2-,4-GbpsFibre Channel transceivers. The Fibre Channel plus Ethernet expansion module is afield-replaceableunit (FRU).Figure 1-6 shows the Fibre Channel plus Ethernet expansion module.

Figure 1-6Fibre Channel Plus Ethernet Expansion Module

186384

Figure 1-7 shows the front of the Fibre Channel plus Ethernet expansion module.Figure 1-11 shows how ports are numbered on the Fibre Channel plus Ethernet expansion module.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

1-5

 

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Figure 1-7Front of the Fibre Channel Plus Ethernet Expansion Module f

1

10 GIGABIT ETHERNET

3

1/2/4G FIBRE CHANNEL

1

2

3

4

1

2

3

4

2

186258

1

Four 10-GigabitEthernet ports

3

Four 1-,2-,4-GbpsFibre Channel ports

 

 

 

 

2

Module LED

 

 

 

 

 

 

See Figure 1-11 for an illustration how ports are grouped and numbered on the Fibre Channel plus Ethernet expansion module.

Ethernet Expansion Module

The Ethernet expansion module supports six 10-GigabitEthernet ports, four of which will have encryption capability. The Ethernet expansion is afield-replaceableunit (FRU).Figure 1-8 shows the Ethernet expansion module.

Figure 1-8Ethernet Expansion Module

1

3

10 GIGABIT ETHERNET

1

2

3

4

5

6

2

186259

 

 

 

 

1 & 3

Six 10-GigabitEthernet ports

2

Module LED

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1-6

 

 

 

 

 

OL-15902-01

 

 

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

See Figure 1-12 for an illustration of how ports are grouped and numbered on the Ethernet expansion module.

N5K-M1008

The N5K-M1008GEM supports 8 1/2/4G Fiber Channel, SFP based uplink connection.Figure 1-25 shows theN5K-M1008GEM.

Figure 1-9N5K-M1008GEM

189953

Figure 1-10Front of theN5K-M1008GEM

1

1

2

3

4

5

6

7

8

189954

2

1

Eight 1-,2-,4-GbpsFibre Channel ports

2

LED

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

1-7

 

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Ports

Each individual port on the Cisco Nexus 5020 switch is numbered, and groups of ports are numbered based on their function. The ports are numbered top to bottom and left to right. The 40 fixed ports form group 1 and are named 1/port_number. Ports 1 through 32 are unencrypted Ethernet ports. Of these, ports 1 through 16 are10-GigabitEthernet and1-GigabitEthernet capable ports. Ports 33 through 40 areencryption-capableEthernet ports.

Group 2 includes the ports in the top-mostexpansion module. Group 2 ports 1 through 4 are encrypted Ethernet ports. Group 2 ports 5 through 8 are Fibre Channel ports.

Group 3 includes the ports in the bottom-mostexpansion module. Group 3 ports 1 through 4 are encrypted Ethernet ports. Group 3 ports 5 through 8 are Fibre Channel ports.

Figure 1-11 shows how ports are numbered and grouped by function for both the fixed ports and the Fibre Channel plus Ethernet expansion module ports.

Figure 1-11Port Numbering of Fixed Ports and Fibre Channel Plus Ethernet Expansion Module Ports

A

B

C

D

E

 

 

 

 

186386

A

Group 1/ports 1 through 16: 10-Gigabit

D

Groups 2 and 3/ ports 1 through 4: Encrypted

 

Ethernet and 1-GigabitEthernet capable

 

Ethernet ports

 

unencrypted ports

 

 

 

 

 

 

B

Group 1/ports 1 through 32: Unencrypted

E

Groups 2 and 3/ ports 5 through 8: Fibre

 

Ethernet ports

 

Channel ports

 

 

 

 

C

Group 1/ports 33 through 40: Encrypted

 

 

 

Ethernet ports

 

 

 

 

 

 

Figure 1-12 shows how ports are numbered and grouped by function for both the fixed ports and the Ethernet expansion module ports.

Cisco Nexus 5000 Series Hardware Installation Guide

1-8

OL-15902-01

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Figure 1-12Port Numbering of Fixed Ports and the Ethernet Expansion Module

A

B

C

D

E

 

 

 

 

186387

A

Group 1/ports 1 through 16: 10-Gigabit

D

Groups 2 and 3/ ports 1 through 4: Encrypted

 

Ethernet and 1-GigabitEthernet capable

 

Ethernet ports

 

Encrypted ports

 

 

 

 

 

 

B

Group 1/ports 1 through 32: Unencrypted

E

Groups 2 and 3/ ports 5 through 6:

 

Ethernet ports

 

Unencrypted Ethernet ports

 

 

 

 

C

Group 1/ports 33 through 40: Encrypted

 

 

 

Ethernet ports

 

 

 

 

 

 

Power Supply

The Cisco Nexus 5020 switch uses a front-endpower supply. The chassis has slots for two power supplies. Two power supplies can be used for redundancy, but the Cisco Nexus 5020 switch is fully functional with one power supply.Figure 1-13 shows the power supply, which has two LEDs: one for power status and one for failure condition.

Figure 1-13Power Supply for the Cisco Nexus 5020 Switch

1 2

186264

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

1-9

 

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

1 Green power LED indicates the power status.2 Amber fail LED indicates a failure condition.

Table 1-2 table describes the status of the two power supply LEDs.

Table 1-2

Power Supply LED Descriptions

 

 

 

 

 

Power Supply Condition

Power LED Status

Fail LED Status

 

 

 

No AC power to all power supplies.

Off

Off

 

 

 

Power supply failure, including over voltage, over current,

Off

On

over temperature, and fan failure.

 

 

 

 

 

Power supply warning events where the power supply

Off

1 Hz Blinking

continues to operate. These events include high

 

 

temperature, high power, and slow fan.

 

 

 

 

 

AC present, 3.3 voltage standby (VSB) on, and the power

1 Hz blinking

Off

supply unit is off.

 

 

 

 

 

Power supply on and OK.

On

Off

 

 

 

 

If one power supply is installed in the chassis, but the other power supply slot is empty, a blank filler panel should be used to cover the empty slot. Figure 1-14 shows a blank power supply filler panel.

Figure 1-14Blank Power Supply Filler Panel

186854

Fan Module

The Cisco Nexus 5020 switch has five fans modules. Figure 1-15 shows the fan module.

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-10

OL-15902-01

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Figure 1-15Cisco Nexus 5020 Fan Module

1

186263

1 Fan module LED

The bicolor fan module LED indicates fan tray health. Green indicates normal operation, while amber indicates a fan failure.

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

1-11

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

LED Descriptions

Table 1-3 describes the LEDs for the Cisco Nexus 5020 switch.

Table 1-3

LEDs for the Cisco Nexus 5020 Switch

 

 

 

 

 

 

 

 

LED

Location

Function

Color

Status

Description

 

 

 

 

 

 

Chassis

Front and back

Chassis

Green

Solid on

All diagnostics pass. The

 

of chassis

power and

 

 

module is operational.

 

 

health

 

 

 

 

 

 

Off

The module is not receiving

 

 

 

 

 

 

 

 

 

power.

 

 

 

 

 

 

 

 

 

Amber

On

The module is booting or

 

 

 

 

 

running diagnostics.

 

 

 

 

 

An over temperature condition

 

 

 

 

 

has occurred. The temperature

 

 

 

 

 

threshold has been exceeded

 

 

 

 

 

by a small value during

 

 

 

 

 

environmental monitoring.

 

 

 

 

 

 

 

 

 

 

Blinking

An over temperature condition

 

 

 

 

 

has occurred. The temperature

 

 

 

 

 

threshold has been exceeded

 

 

 

 

 

by a large value during

 

 

 

 

 

environmental monitoring.

 

 

 

 

 

If the module fails during

 

 

 

 

 

initial reset, the LED

 

 

 

 

 

continues to blink and the

 

 

 

 

 

module does not come online.

 

 

 

 

 

The module has runtime

 

 

 

 

 

failure and is brought offline.

 

 

 

 

 

 

Fan module

Fan modules

Fan

Green

Solid on

All diagnostics pass. The

 

(front)

module

 

 

module is operational.

 

 

health

 

 

 

 

 

 

Off

The module is not receiving

 

 

indicator

 

 

 

 

 

power.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Amber

Solid on

The module is booting or

 

 

 

 

 

running diagnostics.

 

 

 

 

 

 

 

 

 

Amber

Blinking

If the module fails during

 

 

 

 

 

initial reset, the LED

 

 

 

 

 

continues to blink and the

 

 

 

 

 

module does not come online.

 

 

 

 

 

The module has runtime

 

 

 

 

 

failure and is brought offline.

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-12

OL-15902-01

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Table 1-3

LEDs for the Cisco Nexus 5020 Switch (continued)

 

 

 

 

 

 

 

LED

Location

Function

Color

Status

Description

 

 

 

 

 

 

Power supply

Power supply

Power

Green

Solid on

Power supply is on and okay.

 

(front)

supply

 

 

 

 

 

Off

No AC power to the power

 

 

health

 

 

 

 

 

supply.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Amber

Solid on

Power supply failures, over

 

 

 

 

 

voltage, over current, over

 

 

 

 

 

temperature.

 

 

 

 

 

 

 

 

 

 

1 Hz

AC is present, 3.3 VSB on, and

 

 

 

 

Blinking

the power supply is off.

 

 

 

 

 

 

 

 

 

 

Off

Operating normally.

 

 

 

 

 

 

Module

Back of chassis

Indicator

Green

On

All diagnostics pass. The

 

 

of a fault

 

 

module is operational.

 

 

with any

 

 

 

 

 

 

Off

The module is not receiving

 

 

expansion

 

 

 

 

 

power.

 

 

module

 

 

 

 

 

 

 

 

 

Amber

Solid on

The module is booting or

 

 

 

 

 

 

 

 

running diagnostics.

 

 

 

 

 

An over temperature condition

 

 

 

 

 

has occurred. The temperature

 

 

 

 

 

threshold has been exceeded

 

 

 

 

 

by a small value during

 

 

 

 

 

environmental monitoring.

 

 

 

 

 

 

 

 

 

 

Blinking

An over temperature condition

 

 

 

 

 

has occurred. The temperature

 

 

 

 

 

threshold has been exceeded

 

 

 

 

 

by a large value during

 

 

 

 

 

environmental monitoring.

 

 

 

 

 

If the module fails during

 

 

 

 

 

initial reset, the LED

 

 

 

 

 

continues to blink and the

 

 

 

 

 

module does not come online.

 

 

 

 

 

The module has runtime

 

 

 

 

 

failure and is brought offline

 

 

 

 

 

 

Port LED

Back of the

Indicates

Green

Off

The port is not active or the link

 

chassis

LED status

 

 

is not connected.

 

 

 

 

 

 

 

 

 

 

Solid on

The port is active. The link is

 

 

 

 

 

connected and operational.

 

 

 

 

 

 

 

 

 

Amber

Solid on

The module or port is disabled

 

 

 

 

 

through the CLI command or

 

 

 

 

 

the module is initializing.

 

 

 

 

 

 

 

 

 

 

Blinking

The port is faulty and has been

 

 

 

 

 

disabled.

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

1-13

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5020 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Supported SFP Transceivers

The Cisco Nexus 5020 switch supports both SFP+ Ethernet transceivers and SFP Fibre Channel transceivers.

SFP+ Transceivers

The enhanced Small-Form-FactorPluggable (SFP+)10-GigabitEthernet transceiver module is a bidirectional device with a transmitter and receiver in the same physical package. It has a20-pinconnector on the electrical interface and duplex LC connector on the optical interface.The Cisco Nexus 5020 switch supports theSFP-10G-SRtransceiver.

Model

Description

 

 

SFP-10G-SR

10-GigabitEthernet—shortrange SFP+ module

 

 

Figure 1-16 shows theSFP-10G-SRtransceiver.

 

Figure 1-16SFP+10-GigabitEthernet Transceiver Module

187492

SFP+ Copper Cables

Copper cables are available for use with the 10-GigabitEthernet SFP+ module. The cables come in the following lengths:

1m, 30AWG

3m, 28-30AWG

5m, 26-28AWG

7m, 24-26AWG

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-14

OL-15902-01

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Model

Description

 

 

SFP-H10GB-CU1M

10GBASE-CUSFP+ Cable 1 Meter

 

 

SFP-H10GB-CU3M

10GBASE-CUSFP+ Cable 3 Meter

 

 

SFP-H10GB-CU5M

10GBASE-CUSFP+ Cable 5 Meter

 

 

SFP-H10GB-CU7M

10GBASE-CUSFP+ Cable 7 Meter

 

 

SFP Fiber Channel Transceivers

The Cisco Nexus 5020 switch also supports the following SFP Fibre Channel transceiver:

Model

Description

 

 

DS-SFP-FC4G-SW

4-Gbps/2-Gbps/1-GbpsFibreChannel—short

 

wavelength SFP module

 

 

Nexus 5010 Switch

This section describes the Cisco Nexus 5010 switch and its components. This section includes the following topics:

Features, page 1-16

Chassis, page 1-16

Ports, page 1-23

Expansion Modules, page 1-20

Power Supply, page 1-25

Fan Module, page 1-26

LED Descriptions, page 1-27

Supported SFP Transceivers, page 1-28

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

1-15

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Features

The Cisco Nexus 5010 switch is a 1RU, top-of-rackswitch that provides Ethernet and Fibre Channel consolidation in a single physical cable. The Fibre Channel over Ethernet (FCoE) protocol is used to consolidate Ethernet and Fibre Channel traffic onto the same physical connection between the server and the switch. As atop-of-rackswitch, all the servers in the rack connect to the Cisco Nexus 5010 switch, and it connects to the LAN or SAN.

The Cisco Nexus 5010 switch is a part of a family of switches that provide 10-GigabitEthernet and FCoE ports and both10-GigabitEthernet and native1-,2-,and4-GbpsFibre Channel ports. The switches provide consolidated I/O connectivity to both production Ethernet LANs and Fibre Channel SANs in acost-effective,high-performance,low-latencyEthernet switch.

The Cisco Nexus 5010 switch has the following features:

One slot on the back of the switch for an optional uplink Gatos Expansion Module [GEM]. There are several modules which can be accommodated in this slot. Three such modules are N5K-M1404,N5K-M1600andN5K-M1008.

Twenty to twenty-eightports on the back of the switch depending on which GEM is installed. This is because twenty ports on Cisco Nexus 5010 switch belong to the base switch. Additionally, one module can be inserted which can be of 6 or 8 ports.

Two slots on the front of the switch for hot swap-capablepower supplies.

Two slots on the front of the switch for fan modules. Each fan module houses six fans. The combination of six fans per module and two modules provides the switch with a total of 12-fans.

Chassis

The Cisco Nexus 5010 chassis is 1 RU, 1.72 inches tall, 17.3 inches wide and 30.0 inches deep. It is designed to be mounted in a standard 19-inchrack. The switch has two power supplies and two fans modules on the front of the switch. Ports are at the rear of the switch. The airflow is front to back.

Figure 1-17 shows the front of the Cisco Nexus 5010 switch.

Figure 1-17Cisco Nexus 5010 Switch Front View

1

2

189949

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-16

OL-15902-01

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

1

Two power supplies

2

Two fan modules

 

 

 

 

Figure 1-18 shows aclose-upview of the front of the switch.

Figure 1-18Cisco Nexus 5010 Switch Front ViewClose-up

1

2

3

189950

1

Two power supplies

3

System status LED

 

 

 

 

2

Two fan modules

 

 

 

 

 

 

The rear of the Cisco Nexus 5010 chassis has 20 fixed 10-GigabitEthernet ports, 1 slot for an optional expansion module, an Ethernet connector with 2cross-connectports and 2 management ports, a console port, and 2 AC power connectors.Figure 1-19 shows the rear of the Cisco Nexus 5010 switch.

Figure 1-19Cisco Nexus 5010 Switch Rear View

1

2

3 4

5

6

189951

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

1-17

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

1

System status LED

4

20 fixed 10-GigabitEthernet ports

 

 

 

 

2

Ethernet connector with two cross-connect

5

Expansion modules

 

ports on the left (top and bottom), and two

 

 

 

network management ports on the right (top

 

 

 

and bottom)

 

 

 

 

 

 

3

Console port

6

AC power connectors

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-18

OL-15902-01

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Figure 1-20 shows aclose-upview of the rear of the Cisco Nexus 5010 chassis.

Figure 1-20Cisco Nexus 5010 Switch Rear ViewClose-up

1

189952

2

3

4

5

6

1

System status LED

4

Slot 1, with 20 fixed 10-GigabitEthernet ports

 

 

 

(highlighted in red).

 

 

 

 

2

Ethernet connector with two cross-connect

5

Slot 2 for an optional expansion module

 

ports on left side, and two network

 

 

 

management1 (top) and management2

 

 

 

(bottom) ports on the right side

 

 

 

 

 

 

3

Console port

6

AC power connectors

 

 

 

 

The Ethernet connector port exposes four Ethernet ports that are in a 2x2 stacked RJ-45jack.Figure 1-21 shows aclose-upview of the Ethernet connector port.

Figure 1-21Ethernet Connector Port

1

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

186385

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Internal cross connect ports

 

 

 

2

Network management ports

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

1-19

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Table 1-4 lists the LED descriptions for all Ethernet LEDs.

Table 1-4

Ethernet LED Descriptions

 

 

 

 

 

LED

 

Status

Description

 

 

 

 

Left

 

Off

No link

 

 

 

 

 

 

Solid green

Physical link

 

 

 

 

Right

 

Off

No activity

 

 

 

 

 

 

Blinking green

Activity

 

 

 

 

Expansion Modules

Expansion modules allow Cisco Nexus 5000 switches to be configured as cost-effective10-GigabitEthernet switches and as I/O consolidation platforms with native Fibre Channel connectivity. The Cisco Nexus 5010 switch has one slot for an optional uplink Gatos Expansion Module (GEM). There are several modules which can be accommodated in this slot. Three such modules areN5K-M1404,N5K-M1600andN5K-M1008.

N5K-M1404provides 4 10G SFP+, and 4 Fiber Channel 1/2/4G SFP based uplink connections. The 10GE ports are encryption capable.

M5K-M1600provides 6 10G SFP+ based uplink connections.

N5K-M1008provides 8 1/2/4G Fiber Channel, SFP based uplink connection.

The chassis supports hot swapping of the expansion modules.

N5K-M1404

The N5K-M1404GEM supports four SFP+ transceiver modules and four1-,2-,4-GbpsFibre Channel transceivers. The Fibre Channel plus Ethernet expansion module is afield-replaceableunit (FRU).Figure 1-22 shows the Fibre Channel plus Ethernet expansion module.

Figure 1-22N5K-M1404Gatos Expansion Module

 

186384

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-20

OL-15902-01

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Figure 1-23 shows the front of the Fibre Channel plus Ethernet expansion module.Figure 1-11 shows how ports are numbered on the Fibre Channel plus Ethernet expansion module.

Figure 1-23Front of theN5K-M1404GEM

1

10 GIGABIT ETHERNET

3

1/2/4G FIBRE CHANNEL

1

2

3

4

1

2

3

4

2

186258

1

Four 10-GigabitEthernet ports

3

Four 1-,2-,4-GbpsFibre Channel ports

 

 

 

 

2

Module LED

 

 

 

 

 

 

N5K-M1600

The N5K-M1600GEM supports 6 10G SFP+ based uplink connections.Figure 1-24 shows theN5K-M1600GEM.

Figure 1-24N5K-M1600GEM

1

3

10 GIGABIT ETHERNET

1

2

3

4

5

6

2

186259

1 & 3

Six 10-GigabitEthernet ports

2

Module LED

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

1-21

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

See Figure 1-12 for an illustration of how ports are grouped and numbered on the Ethernet expansion module.

N5K-M1008

The N5K-M1008GEM supports 8 1/2/4G Fiber Channel, SFP based uplink connection.Figure 1-25 shows theN5K-M1008GEM.

Figure 1-25N5K-M1008GEM

189953

Figure 1-26Front of theN5K-M1008GEM

1

1

2

3

4

5

6

7

8

189954

2

1

Eight 1-,2-,4-GbpsFibre Channel ports

2

LED

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-22

OL-15902-01

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Ports

Each individual port on the Cisco Nexus 5010 switch is numbered, and groups of ports are numbered based on their function. The ports are numbered top to bottom and left to right.

There are 20-28ports on the Cisco Nexus 5010 switch, depending on which GEM is installed.

The 20 fixed ports form group 1 and are named 1/port_number. Ports 1 through 16 are unencrypted Ethernet ports. Of these, ports 1 through 8 are10-GigabitEthernet and1-GigabitEthernet capable ports. Ports 17 through 20 areencryption-capableEthernet ports.

Group 2 includes the ports in the GEM module. Group 2 ports 1 through 4 are encrypted Ethernet ports. Group 2 ports 5 through 8 are Fibre Channel ports.

Figure 1-27 shows how ports are numbered and grouped by function with theN5K-M1404GEM installed.

Figure 1-27Port Numbering of the Cisco Nexus 5010 switch configured with theN5K-M1404GEM

 

 

A

 

 

 

B

 

 

C

 

D

 

E

1

3

5

7

9

11

13

15

17

19

1

3

5

7

1

 

 

 

 

 

 

 

 

 

2

 

 

 

2

4

6

8

10

12

14

16

18

20

2

4

6

8

 

 

 

 

 

 

 

 

 

 

 

 

 

192241

A

Group 1/ports 1 through 8: 10-Gigabit

D

Group 2 ports 1 through 4: Encrypted

 

Ethernet and 1-GigabitEthernet capable

 

Ethernet ports

 

unencrypted ports

 

 

 

 

 

 

B

Group 1/ports 1 through 16: Unencrypted

E

Group 2 ports 5 through 8: Fibre Channel

 

Ethernet ports

 

ports

 

 

 

 

C

Group 1/ports 17 through 20: Encrypted

 

 

 

Ethernet ports

 

 

 

 

 

 

Figure 1-28 shows how ports are numbered and grouped by function with theN5K-M1600GEM installed.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

1-23

 

 

 

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Figure 1-28Port Numbering of the Cisco Nexus 5010 switch configured with theN5K-M1600GEM

 

 

A

 

 

 

B

 

 

C

 

D

E

1

3

5

7

9

11

13

15

17

19

1

3

5

1

 

 

 

 

 

 

 

 

 

2

 

 

2

4

6

8

10

12

14

16

18

20

2

4

6

 

 

 

 

 

 

 

 

 

 

 

 

192242

A

Group 1/ports 1 through 8: 10-Gigabit

D

Group 2 ports 1 through 4: Encrypted

 

Ethernet and 1-GigabitEthernet capable

 

Ethernet ports

 

unencrypted ports

 

 

 

 

 

 

B

Group 1/ports 1 through 16: Unencrypted

E

Group 2 ports 5 and 8: Unencrypted Ethernet

 

Ethernet ports

 

ports

 

 

 

 

C

Group 1/ports 17 through 20: Encrypted

 

 

 

Ethernet ports

 

 

 

 

 

 

Figure 1-29 shows how ports are numbered and grouped by function with theN5K-M1008GEM installed.

Figure 1-29Port Numbering of the Cisco Nexus 5010 switch configured with theN5K-M1008GEM

 

 

A

 

 

 

B

 

 

C

 

 

D

 

1

3

5

7

9

11

13

15

17

19

1

3

5

7

1

 

 

 

 

 

 

 

 

 

2

 

 

 

2

4

6

8

10

12

14

16

18

20

2

4

6

8

 

 

 

 

 

 

 

 

 

 

 

 

 

192243

Cisco Nexus 5000 Series Hardware Installation Guide

1-24

OL-15902-01

 

 

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

A

Group 1/ports 1 through 8: 10-Gigabit

D

Group 2 ports 1 through 8: Fibre Channel

 

Ethernet and 1-GigabitEthernet capable

 

ports

 

unencrypted ports

 

 

 

 

 

 

B

Group 1/ports 1 through 16: Unencrypted

 

 

 

Ethernet ports

 

 

 

 

 

 

C

Group 1/ports 17 through 20: Encrypted

 

 

 

Ethernet ports

 

 

 

 

 

 

Power Supply

The Cisco Nexus 5010 switch uses a front-endpower supply. The chassis has slots for two power supplies. Two power supplies can be used for redundancy, but the Cisco Nexus 5010 switch is fully functional with one power supply.Figure 1-30 shows the power supply, which has two LEDs: one for power status and one for failure condition.

Figure 1-30Power Supply for the Cisco Nexus 5010 Switch

1

2

189955

1 Amber fail LED indicates a failure condition.2 Green power LED indicates the power status.

Table 1-5 table describes the status of the two power supply LEDs.

Table 1-5

Power Supply LED Descriptions

 

 

 

 

 

Power Supply Condition

Power LED Status

Fail LED Status

 

 

 

No AC power to all power supplies.

Off

Off

 

 

 

Power supply failure, including over voltage, over current,

Off

On

over temperature, and fan failure.

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

1-25

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Table 1-5

Power Supply LED Descriptions (continued)

 

 

 

 

Power Supply Condition

Power LED Status

Fail LED Status

 

 

 

Power supply warning events where the power supply

Off

1 Hz Blinking

continues to operate. These events include high

 

 

temperature, high power, and slow fan.

 

 

 

 

 

AC present, 3.3 voltage standby (VSB) on, and the power

1 Hz blinking

Off

supply unit is off.

 

 

 

 

 

Power supply on and OK.

On

Off

 

 

 

 

If one power supply is installed in the chassis, but the other power supply slot is empty, a blank filler panel should be used to cover the empty slot. Figure 1-31 shows a blank power supply filler panel.

Figure 1-31Blank Power Supply Filler Panel

186854

Fan Module

The Cisco Nexus 5010 switch has slots for two fans modules. Each fan module houses six fans. The combination of 6-fansper module and2-modulesprovides the switch with a total of12-fans.Figure 1-32 shows the fan module.

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-26

OL-15902-01

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Figure 1-32Cisco Nexus 5010 Fan Module

1

1 Fan module LED

189956

The bicolor fan module LED indicates fan tray health. Green indicates normal operation, while amber indicates a fan failure.

LED Descriptions

Table 1-6 describes the LEDs for the Cisco Nexus 5010 switch.

Table 1-6

LEDs for the Cisco Nexus 5010 Switch

 

 

 

 

 

 

 

 

LED

Location

Function

Color

Status

Description

 

 

 

 

 

 

Power LED

Front of

Chassis

Green

Solid On

System is and on operation

 

Chassis

Power/Hea

 

 

normally

 

 

lth

 

 

 

 

 

 

Off

Switch is powered off

 

 

 

 

 

 

 

 

 

 

 

 

 

Amber

On

Fault condition

 

 

 

 

 

 

 

 

 

 

 

 

Fan Tray Status

Fan

Fan tray

Green

Solid On

Fan tray operating

 

trays (front)

heath

 

 

normally

 

 

indicator

 

 

 

 

 

 

 

 

 

 

(multi color)

 

 

 

 

 

Amber

Solid On

Fan failure within the fan

 

 

 

 

 

tray

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

1-27

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

Table 1-6LEDs for the Cisco Nexus 5010 Switch (continued)

LED

Location

Function

Color

Status

Description

 

 

 

 

 

 

PSU Status

Power supply

PSU Health

Green

OFF

No AC power to power supply

Indicators

(front)

(multi color)

 

 

 

 

Solid On

Power supply on and OK

 

 

 

 

 

 

 

 

 

 

 

 

 

Amber

Solid On

Power supply failures, over volt-

 

 

 

 

 

age, over current, over temperature

 

 

 

 

 

 

 

 

 

 

1 Hz

AC present, 3.3VSB on,

 

 

 

 

blinking

PSU is off

 

 

 

 

 

 

 

 

 

 

OFF

Operating normally

 

 

 

 

 

 

GEM Cards

back of chassis

An indicator

Green

On

GEM card is operating

Health Indicator

 

to show

 

 

normally

 

 

there is a

 

 

 

 

 

 

 

 

 

 

fault with

 

 

 

 

 

Amber

Solid on

A fault has occurred on

 

 

any one of

 

 

the GEM card.

 

 

the GEM

 

 

 

 

 

card

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Port Level LED’s

There are twenty to twenty-sixport activity LEd’s on switch depending on whether the GEM is a Fibre Channel or 10GE. The table summarizes the behavior of the port LED’s.

Link State

LED State

Notes

 

 

 

Link Down

OFF

 

 

 

 

POST failed on port

AMBER blinking yellow

 

 

 

 

Administrative disabled

AMBER_ON

Depending on the product you look at, the

 

 

LED could be off, or solid amber.

 

 

 

Link Up,

GREEN_ON

Blinks based on network activity

port in STP forwarding

 

 

state

 

 

 

 

 

Supported SFP Transceivers

The Cisco Nexus 5010 switch supports both SFP+ Ethernet transceivers and SFP Fibre Channel transceivers.

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-28

OL-15902-01

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

SFP+ Transceivers

The enhanced Small-Form-FactorPluggable (SFP+)10-GigabitEthernet transceiver module is a bidirectional device with a transmitter and receiver in the same physical package. It has a20-pinconnector on the electrical interface and duplex LC connector on the optical interface.The Cisco Nexus 5010 switch supports the following SFP+ optical transceivers:

SR

DCR, SR-Lite(shorter reach than SR)

LRM (for uplink only)

LR (for uplink only)

Model

Description

 

 

SFP-10G-SR

10-GigabitEthernet—shortrange SFP+ module

 

 

SFP-10G-LR

10-GigabitEthernet—longrange SFP+ module

 

 

SFP+ Copper Cables

Copper cables are available for use with the 10-GigabitEthernet SFP+ module. The cables come in the following lengths:

1m, 30AWG

3m, 28-30AWG

5m, 26-28AWG

7m, 24-26AWG

Model

Description

 

 

SFP-H10GB-CU1M

10GBASE-CUSFP+ Cable 1 Meter

 

 

SFP-H10GB-CU3M

10GBASE-CUSFP+ Cable 3 Meter

 

 

SFP-H10GB-CU5M

10GBASE-CUSFP+ Cable 5 Meter

 

 

SFP-H10GB-CU7M

10GBASE-CUSFP+ Cable 7 Meter

 

 

SFP Fiber Channel Transceivers

The Cisco Nexus 5010 switch supports the multimode 850nm 4Gbps SFP with 150m reach.

Model

Description

 

 

DS-SFP-FC4G-SW

4 Gbps Fibre Channel-SWSFP, LC

DS-SFP-FC4G-LW

4 Gbps Fibre Channel-LWSFP, LC, (10km

 

Reach)

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

1-29

 

 

 

 

 

Chapter 1 Product Overview

Nexus 5010 Switch

Se n d d o c u m e n t a t i o n c o m m e n t s t o n x 5 0 0 0 - d o c f e e d b a ck @ c i s c o . c o m

 

Cisco Nexus 5000 Series Hardware Installation Guide

1-30

OL-15902-01

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

C H A P T E R 2

Installing the Cisco Nexus 5000 Switch

This chapter describes how to install the Cisco Nexus 5000 switch, and it includes the following information:

Preparing for Installation, page 2-2

Installing the Cisco Nexus 5020 Chassis in a Cabinet or Rack, page 2-5

Grounding the System, page 2-10

Grounding the Chassis, page 2-15

Starting the Switch, page 2-17

Removing and Installing Components, page 2-18

Repacking the Cisco Nexus 5000 Switch for Return Shipment, page 2-26

Note Before you install, operate, or service the system, read theRegulatory Compliance and Safety Information for the Cisco Nexus 5000 Family for important safety information.

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Warning Only trained and qualified personnel must be allowed to install, replace, or service this equipment.

Statement 1030

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

2-1

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Preparing for Installation

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Note Each new switch requires a license. For information on licensing, see theCisco Nexus 5000 Series CLI Configuration Guide.

Preparing for Installation

This section includes the following topics:

Installation Options, page 2-2

Installation Guidelines, page 2-3

Required Equipment, page 2-4

Unpacking and Inspecting the Switch, page 2-4

Installation Options

The Cisco Nexus 5000 switch can be installed using the following methods:

In an open EIA rack, using the following items:

The rack-mountkit shipped with the switch

The EIA Shelf Bracket Kit (an optional kit, purchased separately)

In a perforated or solid-walledEIA cabinet, using:

The rack-mountkit shipped with the switch

The EIA Shelf Bracket Kit (an optional kit, purchased separately)

For instructions on installing the switch using the rack-mountkit shipped with the switch, see the“Installing the Cisco Nexus 5020 Chassis in a Cabinet or Rack” section on page 2-5.

Note The optional EIA Shelf Bracket Kit is not provided with the switch. To order the kit, contact your switch provider.

Airflow Considerations

Airflow through the Cisco Nexus 5000 switch is from front to back. Air enters the chassis through the fan trays and power supplies mounted at the front of the chassis and exits the chassis through perforations on the rear of the chassis. To ensure proper airflow, follow these guidelines:

Maintain ambient airflow throughout the data center to ensure normal operation.

Consider the heat dissipation of all equipment when determining air-conditioningrequirements. When evaluating airflow requirements, take into consideration that hot air generated by equipment at the bottom of the rack can be drawn in the intake ports of the equipment above.

Chassis Weight

When lifting the system, follow these guidelines:

Cisco Nexus 5000 Series Hardware Installation Guide

2-2

OL-15902-01

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Preparing for Installation

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Disconnect all power and external cables before lifting the system.

Have two people to lift the system. The Nexus 5020 weighs 50 lb (22.680 kg) and the Nexus 5010 weighs 35 lb.

Ensure that your footing is solid and the weight of the system is evenly distributed between your feet.

Lift the system slowly, keeping your back straight. Lift with your legs, not with your back. Bend at the knees, not at the waist.

Installation Guidelines

When installing the Cisco Nexus 5000 switch, follow these guidelines:

Plan your site configuration and prepare the site before installing the chassis. Appendix D, “Site Planning and Maintenance Records,” lists the recommended site planning tasks.

Record the information listed in Appendix D, “Site Planning and Maintenance Records,” as you install and configure the switch.

Ensure that there is adequate space around the switch to allow for servicing the switch and for adequate airflow (Appendix B, “Technical Specifications,” lists airflow requirements).

Ensure that the air-conditioningmeets the heat dissipation requirements listed inAppendix B, “Technical Specifications.”

Ensure that the cabinet or rack meets the requirements listed in Appendix A, “Cabinet and Rack Installation.”

Note Jumper power cords are available for use in a cabinet. See the“Jumper Power Cord” section on page C-10.

Ensure that the chassis is adequately grounded. If the switch is not mounted in a grounded rack, we recommend connecting both the system ground on the chassis and the power supply ground to an earth ground.

Ensure that the site power meets the power requirements listed in Appendix B, “Technical Specifications.” If available, you can use an uninterruptible power supply (UPS) to protect against power failures.

Caution Avoid UPS types that use ferroresonant technology. These UPS types can become unstable with systems such as the Cisco Nexus 5000 switch, which can have substantial current draw fluctuations because of fluctuating data traffic patterns.

Ensure that circuits are sized according to local and national codes. For North America, the power supply requires a 15-Aor20-Acircuit.

Caution To prevent loss of input power, ensure the total maximum loads on the circuits supplying power to the switch are within the current ratings for the wiring and breakers.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

2-3

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Preparing for Installation

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Use the following screw torques when installing the switch:

Captive screws: 4 in-lb

M3 screws: 4 in-lb

M4 screws: 12 in-lb

10-32screws: 20in-lb

12-24screws: 30in-lb

Required Equipment

Before beginning the installation, ensure that the following items are ready:

Number 1 and number 2 Phillips screwdrivers with torque capability

3/16-in.flat-bladescrewdriver

Tape measure and level

ESD wrist strap or other grounding device

Antistatic mat or antistatic foam

The following additional items (not found in the accessory kit) are required to ground the chassis:

Grounding cable (6 AWG recommended), sized according to local and national installation requirements; the required length depends on the proximity of the Cisco Nexus 5000 switch to proper grounding facilities

Crimping tool large enough to accommodate girth of lug

Wire-strippingtool

Unpacking and Inspecting the Switch

Caution When handling switch components, wear an ESD strap and handle modules by the carrier edges only. An ESD socket is provided on the chassis. For the ESD socket to be effective, the chassis must be grounded through the power cable, the chassis ground, or themetal-to-metalcontact with a grounded rack.

Tip Keep the shipping container in case the chassis requires shipping in the future.

Note The switch is thoroughly inspected before shipment. If any damage occurred during transportation or any items are missing, contact your customer service representative immediately.

To inspect the shipment, follow these steps:

Step 1 Compare the shipment to the equipment list provided by your customer service representative and verify that you have received all items, including the following:

Print documentation

Cisco Nexus 5000 Series Hardware Installation Guide

2-4

OL-15902-01

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Installing the Cisco Nexus 5020 Chassis in a Cabinet or Rack

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Grounding lug kit

Rack-mountkit

ESD wrist strap

Cables with connectors

Any optional items ordered

Step 2 Check for damage and report any discrepancies or damage to your customer service representative. Have the following information ready:

Invoice number of shipper (see packing slip)

Model and serial number of the damaged unit

Description of damage

Effect of damage on the installation

Installing the Cisco Nexus 5020 Chassis in a Cabinet or Rack

This section describes how to use the rack-mountkit provided with the switch to install the Cisco Nexus 5020 switch into a cabinet or rack that meets the requirements described inAppendix A, “Cabinet and Rack Installation.” All Cisco Nexus 5020 switch switches use the same installation procedure.

Caution If the rack is on wheels, ensure that the brakes are engaged or that the rack is otherwise stabilized.

Table 2-1 lists the items contained in therack-mountkit provided with the switch.

Table 2-1

Cisco Nexus 5020 Switch Rack-MountKit

 

 

Quantity

Part Description

 

 

2

Rack-mountbrackets

 

 

16

M4x0.7 x 8-mmPhillips countersunk screws

 

 

2

Rack-mountguides

 

 

12

10-32Rack Nuts

 

 

12

10-32x3/4-inchPhillips countersunk screws

 

 

2

Slider rails

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

2-5

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Installing the Cisco Nexus 5020 Chassis in a Cabinet or Rack

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

To install the switch in a cabinet or rack using the rack-mountkit provided with the switch, follow these steps:

Step 1 Install the frontrack-mountbrackets as follows:

a.Position a front rack-mountbracket against the chassis and align the screw holes as shown inFigure 2-1.Then attach the frontrack-mountbracket to the chassis with six of the M4 screws.

b.Repeat with the other front rack-mountbracket on the other side of the switch.

Figure 2-1Attaching FrontRack-MountBracket to the Cisco Nexus 5020 switch

2 3

1

1 Frontrack-mountbracket

3

Slider rail

2 Rack-mountguides

186363

Step 2 Install therack-mountguides on the switch as follows:

a.Position one of the rack-mountbrackets against the side of the switch and align the screw holes as shown inFigure 2-1.Then attach the bracket to the switch with two of theflat-headM4 screws.

b.Repeat with the other rack-mountbracket on the other side of the switch.

Step 3 Attach the slider rails to the rack as shown inFigure 2-2.Use two12-24screws or two10-32screws, depending on the rack rail thread type. For racks with square holes, insert the12-24cage nuts in position behind the mounting holes in the slider rails.

a.Repeat with the other slider rail on the other side of the rack.

b.Use the tape measure and level to verify that the rails are horizontal and at the same height.

Cisco Nexus 5000 Series Hardware Installation Guide

2-6

OL-15902-01

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Installing the Cisco Nexus 5020 Chassis in a Cabinet or Rack

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure 2-2Installing the Slider Rails

186412

Step 4 Insert the switch into the rack:

a.Using both hands, position the switch with the back of the switch between the front posts of the rack.

b.Align the two rack-mountguides on either side of the switch with the slider rails installed in the rack. Slide therack-mountglides onto the slider rails, and then gently slide the switch all the way into the rack. SeeFigure 2-3.If the switch does not slide easily, try realigning therack-mountglides on the slider rails.

Figure 2-3Sliding the Chassis Into the Rack

186413

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

2-7

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Installing the Cisco Nexus 5010 Chassis in a Cabinet or Rack

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Step 5 Stabilize the switch in the rack by attaching the frontrack-mountbrackets to the frontrack-mountingrails:

a.Insert two screws (12-24or10-32,depending on rack type) through the cage nuts and the holes in one of the frontrack-mountbrackets and into the threaded holes in therack-mountingrail. SeeFigure 2-4.

b.Repeat for the front rack-mountbracket on the other side of the switch.

Figure 2-4Attaching the Switch to the Rack

186414

Installing the Cisco Nexus 5010 Chassis in a Cabinet or Rack

This section describes how to use the rack-mountkit provided with the switch to install the Cisco Nexus 5010 switch into a cabinet or rack that meets the requirements described inAppendix A, “Cabinet and Rack Installation.” All Cisco Nexus 5000 switches use the same installation procedure.

Caution If the rack is on wheels, ensure that the brakes are engaged or that the rack is otherwise stabilized.

Table 2-1 lists the items contained in therack-mountkit provided with the switch.

 

 

 

Table 2-2

Cisco Nexus 5010 Switch Rack-MountKit

 

 

 

Quantity

Part Description

2

Rack-mountbrackets

12

M4x0.7 x 8-mmPhillips countersunk screws

2

Rack-mountguides

10

10-32Rack Nuts

10

10-32x3/4-inchPhillips countersunk screws

2

Slider rails

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

2-8

 

 

OL-15902-01

 

 

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Installing the Cisco Nexus 5010 Chassis in a Cabinet or Rack

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

To install the switch in a cabinet or rack using the rack-mountkit provided with the switch, follow these steps:

Step 1 Install the frontrack-mountbrackets as follows:

a.Position a front rack-mountbracket against the chassis and align the screw holes as shown inFigure 2-1.Then attach the frontrack-mountbracket to the chassis with six of the M4 screws.

b.Repeat with the other front rack-mountbracket on the other side of the switch.

Figure 2-5Attaching FrontRack-MountBracket to the Cisco Nexus 5010 switch

3

2

1

273161

1 Frontrack-mountbracket

3

Slider rail

2 Rack-mountguides

Step 2 Install therack-mountguides on the switch as follows:

a.Position one of the rack-mountbrackets against the side of the switch and align the screw holes. This procedure is the same as that for the Cisco Nexus 5020 switch. SeeFigure 2-1.Then attach the bracket to the switch with two of theflat-headM4 screws.

b.Repeat with the other rack-mountbracket on the other side of the switch.

Step 3 Attach the slider rails to the rack. This procedure is the same as that for the Cisco Nexus 5020 switch. SeeFigure 2-2.Use two12-24screws or two10-32screws, depending on the rack rail thread type. For racks with square holes, insert the12-24cage nuts in position behind the mounting holes in the slider rails.

a.Repeat with the other slider rail on the other side of the rack.

b.Use the tape measure and level to verify that the rails are horizontal and at the same height.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

2-9

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Grounding the System

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure 2-6Installing the Slider Rails

186412

Step 4 Insert the switch into the rack:

a.Using both hands, position the switch with the back of the switch between the front posts of the rack.

b.Align the two rack-mountguides on either side of the switch with the slider rails installed in the rack. Slide therack-mountglides onto the slider rails, and then gently slide the switch all the way into the rack. This procedure is the same as that for the Cisco Nexus 5020 switch. SeeFigure 2-3.If the switch does not slide easily, try realigning therack-mountglides on the slider rails.

Step 5 Stabilize the switch in the rack by attaching the frontrack-mountbrackets to the frontrack-mountingrails:

a.Insert two screws (12-24or10-32,depending on rack type) through the cage nuts and the holes in one of the frontrack-mountbrackets and into the threaded holes in therack-mountingrail. This procedure is the same as that for the Cisco Nexus 5020 switch. SeeFigure 2-4.

b.Repeat for the front rack-mountbracket on the other side of the switch.

Grounding the System

This section describes the need for system grounding and explains how to prevent damage from electrostatic discharge.

Proper Grounding Practices

Grounding is one of the most important parts of equipment installation. Proper grounding practices ensure that the buildings and the installed equipment within them have low-impedanceconnections andlow-voltagedifferentials between chassis. When you properly ground systems during installation, you reduce or prevent shock hazards, equipment damage due to transients, and data corruption.Table 2-3 lists some general grounding practice guidelines.

 

Cisco Nexus 5000 Series Hardware Installation Guide

2-10

OL-15902-01

Chapter 2 Installing the Cisco Nexus 5000 Switch

 

 

 

 

Grounding the System

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

 

Table 2-3Proper Grounding Guidelines

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Electromagnetic Noise Severity

 

 

 

 

 

 

 

Environment

Level

Grounding Recommendations

 

 

 

 

 

 

 

 

Commercial building is

High

All lightning protection devices

 

 

subjected to direct lightning

 

must be installed in strict

 

 

strikes.

 

accordance with manufacturer

 

 

For example, some places in the

 

recommendations. Conductors

 

 

 

carrying lightning current

 

 

United States, such as Florida,

 

 

 

 

should be spaced away from

 

 

are subject to more lightning

 

 

 

 

power and data lines in

 

 

strikes than other areas.

 

 

 

 

accordance with applicable

 

 

 

 

 

 

 

 

recommendations and codes.

 

 

 

 

Best grounding

 

 

 

 

recommendations must be

 

 

 

 

closely followed.

 

 

 

 

 

 

 

 

Commercial building is located

High

Best grounding

 

 

in an area where lightning

 

recommendations must be

 

 

storms frequently occur but is

 

closely followed.

 

 

not subject to direct lightning

 

 

 

 

 

 

 

 

strikes.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Commercial building contains a

Medium to high

Best grounding

 

 

mix of information technology

 

recommendations must be

 

 

equipment and industrial

 

closely followed.

 

 

equipment, such as welding.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Existing commercial building is

Medium

Determine source and cause of

 

 

not subject to natural

 

noise if possible, and mitigate as

 

 

environmental noise or

 

closely as possible at the noise

 

 

man-madeindustrial noise. This

 

source or reduce coupling from

 

 

building contains a standard

 

the noise source to the affected

 

 

office environment. This

 

equipment. Best grounding

 

 

installation has a history of

 

recommendations must be

 

 

malfunction due to

 

closely followed.

 

 

electromagnetic noise.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

New commercial building is not

Low

Electromagnetic noise problems

 

 

subject to natural environmental

 

are not anticipated, but

 

 

noise or man-madeindustrial

 

installing a grounding system in

 

 

noise. This building contains a

 

a new building is often the least

 

 

standard office environment.

 

expensive route and the best way

 

 

 

 

to plan for the future. Best

 

 

 

 

grounding recommendations

 

 

 

 

should be followed as closely as

 

 

 

 

possible.

 

 

 

 

 

 

 

 

Existing commercial building is

Low

Electromagnetic noise problems

 

 

not subject to natural

 

are not anticipated, but

 

 

environmental noise or

 

installing a grounding system is

 

 

man-madeindustrial noise. This

 

always recommended. Best

 

 

building contains a standard

 

grounding recommendations

 

 

office environment.

 

should be followed as much as

 

 

 

 

possible.

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-15902-01

 

 

 

2-11

 

 

 

 

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Grounding the System

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Note In all situations, grounding practices must comply with local National Electric Code (NEC) requirements or local laws and regulations.

Note Always ensure that all of the modules are completely installed and that the captive installation screws are fully tightened. In addition, ensure that all I/O cables and power cords are properly seated. These practices are normal installation practices and must be followed in all installations.

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) damage, which can occur when modules or other FRUs are improperly handled, results in intermittent or complete failures. Modules consist of printed circuit boards that are fixed in metal carriers. Electromagnetic interference (EMI) shielding and connectors are integral components of the carrier. Although the metal carrier helps to protect the board from ESD, always use an ESD grounding strap when handling modules.

For preventing ESD damage, follow these guidelines:

Always use an ESD wrist strap and ensure that it makes maximum contact with bare skin.

ESD grounding straps are available with banana plugs, metal spring clips, or alligator clips. All Cisco Nexus 5000 Series chassis are equipped with a banana plug connector (identified by the ground symbol next to the connector) somewhere on the front panel. We recommend that you use a personal ESD grounding strap equipped with a banana plug.

If you choose to use the disposable ESD wrist strap supplied with most FRUs or an ESD wrist strap equipped with an alligator clip, you must attach the system ground lug to the chassis in order to provide a proper grounding point for the ESD wrist strap.

Note This system ground is also referred to as the network equipment building system (NEBS) ground.

If your chassis does not have the system ground attached, you must install the system ground lug. See “Establishing the System Ground” section on page 2-14 for installation instructions and location of the chassis system ground pads.

Note You do not need to attach a supplemental system ground wire to the system ground lug; the lug provides a direct path to the bare metal of the chassis.

After you install the system ground lug, follow these steps to correctly attach the ESD wrist strap:

Step 1 Attach the ESD wrist strap to bare skin as follows:

a.If you are using the ESD wrist strap supplied with the FRUs, open the wrist strap package and unwrap the ESD wrist strap. Place the black conductive loop over your wrist and tighten the strap so that it makes good contact with your bare skin.

b.If you are using an ESD wrist strap equipped with an alligator clip, open the package and remove the ESD wrist strap. Locate the end of the wrist strap that attaches to your body and secure it to your bare skin.

 

Cisco Nexus 5000 Series Hardware Installation Guide

2-12

OL-15902-01

Chapter 2 Installing the Cisco Nexus 5000 Switch

Grounding the System

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Step 2 Grasp the spring or alligator clip on the ESD wrist strap and momentarily touch the clip to a bare metal spot (unpainted surface) on the rack. We recommend that you touch the clip to an unpainted rack rail so that anybuilt-upstatic charge is then safely dissipated to the entire rack.

Step 3 Attach either the spring clip or the alligator clip to the ground lug screw as follows (SeeFigure 2-7.):

a.If you are using the ESD wrist strap that is supplied with the FRUs, squeeze the spring clip jaws open, position the spring clip to one side of the system ground lug screw head, and slide the spring clip over the lug screw head so that the spring clip jaws close behind the lug screw head.

Note The spring clip jaws do not open wide enough to fit directly over the head of the lug screw or the lug barrel.

b.If you are using an ESD wrist strap that is equipped with an alligator clip, attach the alligator clip directly over the head of the system ground lug screw or to the system ground lug barrel.

The following illustration displays how to attach the ESD Wrist Strap to the System Ground Lug Screw for the 5020 switch. Follow the same procedure for the 5010 switch.

Figure 2-7Attaching the ESD Wrist Strap to the System Ground Lug Screw

5

1

2

3

4

186482

 

1

ESD ground strap

 

3

Side view of grounding lug (clip slid behind

 

 

 

 

 

 

screw)

 

 

 

 

 

 

2

Clip and grounding lug

 

4

Clip installed (behind screw)

 

 

 

 

 

 

 

 

 

5

System ground connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-15902-01

 

 

 

 

 

2-13

 

 

 

 

 

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Grounding the System

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

In addition, follow these guidelines when handling modules:

Handle carriers by available handles or edges only; avoid touching the printed circuit boards or connectors.

Place a removed component board-side-upon an antistatic surface or in astatic-shieldingcontainer. If you plan to return the component to the factory, immediately place it in astatic-shieldingcontainer.

Never attempt to remove the printed circuit board from the metal carrier.

Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be between 1 and 10 megohm (Mohm).

Establishing the System Ground

This section describes how to connect a system ground to the Cisco Nexus 5000 switch.

Note This system ground is also referred to as the network equipment building system (NEBS) ground.

You must use the system (NEBS) ground on AC-poweredsystems if you are installing this equipment in a U.S. or European Central Office.

The system (NEBS) ground provides additional grounding for EMI shielding requirements and grounding for the low-voltagesupplies(DC-DCconverters) on the modules, and is intended to satisfy the Telcordia Technologies NEBS requirements for supplemental bonding and grounding connections. You must observe the following system grounding guidelines for your chassis:

You must install the system (NEBS) ground connection with any other rack or system power ground connections that you make. The system ground connection is required if this equipment is installed in a U.S. or European Central Office.

You must connect both the system (NEBS) ground connection and the power supply ground connection to an earth ground. The system (NEBS) ground connection is required if this equipment is installed in a U.S. or European Central Office.

You do not need to power down the chassis because the Cisco Nexus 5020 switch is equipped with AC-inputpower supplies.

Required Tools and Equipment

To connect the system ground, you need the following tools and materials:

Grounding lug—Atwo-holestandard barrel lug. Supports up to 6 AWG wire. Supplied as part of accessory kit.

Grounding screws—TwoM4 x 8mm (metric)pan-headscrews. Supplied as part of the accessory kit.

Grounding wire—Notsupplied as part of accessory kit. The grounding wire should be sized according to local and national installation requirements. Depending on the power supply and system, a 12 AWG to 6 AWG copper conductor is required for U.S. installations. Commercially available 6 AWG wire is recommended. The length of the grounding wire depends on the proximity of the switch to proper grounding facilities.

No. 1 Phillips screwdriver.

 

Cisco Nexus 5000 Series Hardware Installation Guide

2-14

OL-15902-01

Chapter 2 Installing the Cisco Nexus 5000 Switch

Grounding the Chassis

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Crimping tool to crimp the grounding wire to the grounding lug.

Wire-strippingtool to remove the insulation from the grounding wire.

Grounding the Chassis

The chassis has a grounding pad with two threaded M4 holes for attaching a grounding lug. Figure 2-8 shows the system ground location on the Cisco Nexus 5020 switch. It is identical for the Cisco Nexus 5010 switch.

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last.Statement 1046

Caution We recommend grounding the chassis, even if the rack is already grounded.

Caution All power supplies must be grounded. The receptacles of the AC power cables used to provide power to the chassis must be the grounding type, and the grounding conductors should connect to protective earth ground at the service equipment.

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

2-15

 

 

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Grounding the Chassis

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure 2-8Location of System Ground on a Cisco Nexus 5000 Switch

2 1

3

6

5

4

186483

 

 

1

ESD socket (on switch)

4

Screws, M4, with square cone

 

 

 

 

 

 

 

washers

 

 

 

 

 

 

 

 

 

 

2

ESD plug

5

NRTL listed grounding lug

 

 

 

 

 

 

 

 

 

 

3

Grounding cable

6

Close-upof grounding pad on

 

 

 

 

 

 

 

switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046

Caution Grounding the chassis is required if you are using DC power supplies, even if the rack is already grounded. A grounding pad with two threaded M4 holes is provided on the chassis for attaching a grounding lug. The ground lug must be NRTL listed. In addition, the copper conductor (wires) must be used and the copper conductor must comply with NEC code for ampacity.

To attach the grounding lug and cable to the chassis, follow these steps:

Step 1 Use awire-strippingtool to remove approximately 0.75 inches (19 mm) of the covering from the end of the grounding cable.

Step 2 Insert the stripped end of the grounding cable into the open end of the grounding lug.

Step 3 Use the crimping tool to secure the grounding cable in the grounding lug.

 

Cisco Nexus 5000 Series Hardware Installation Guide

2-16

OL-15902-01

Chapter 2 Installing the Cisco Nexus 5000 Switch

 

Starting the Switch

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Step 4

Remove the adhesive label from the grounding pad on the chassis.

Step 5

Place the grounding lug against the grounding pad so that there is solid metal-to-metalcontact, and insert

 

the two M4 screws with washers through the holes in the grounding lug and into the grounding pad.

Step 6

Ensure that the lug and cable do not interfere with other equipment.

Step 7

Prepare the other end of the grounding cable and connect it to an appropriate grounding point in your

 

site to ensure adequate earth ground.

 

 

 

Starting the Switch

This section provides instructions for powering up the switch and verifying component installation.

Note Do not connect the Ethernet port to the LAN until the initial switch configuration has been performed. For instructions on configuring the switch, see theCisco Nexus 5000 Series CLI Configuration Guide. For instructions on connecting to the console port, see the“Connecting to the Console Port” section on page 3-2.

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046

To power up the switch and verify hardware operation, follow these steps:

Step 1 Verify that empty power supply slots have filler panels installed, the faceplates of all modules are flush with the front of the chassis, and the captive screws of the power supplies, fan module, and all expansion modules are tight.

Step 2 Verify that the power supply and the fan modules are installed.

Note Depending on the outlet receptacle on your power distribution unit, you may need the optional jumper power cord to connect the Cisco Nexus 5000 switch to your outlet receptacle. See the“Jumper Power Cord” section on page C-10.

Step 3 Ensure that the switch is adequately grounded as described in the“Grounding the System” section on page 2-10,and that the power cables are connected to outlets that have the required AC power voltages (see the“Power Specifications” section on page B-2).

Step 4 Connect the power cable to an AC power source. The switch should power on as soon as you connect the power cable.

Step 5 Listen for the fans; they should begin operating when the power cable is plugged in.

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

2-17

 

 

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Removing and Installing Components

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Step 6 After the switch boots, verify that the LED operation is as follows:

Fan module—StatusLED is green.

Power supply—StatusLED is green.

After initialization, the system status LED is green, indicating that all chassis environmental monitors are reporting that the system is operational. If this LED is orange or red, then one or more environmental monitor is reporting a problem.

The Link LEDs for the Ethernet connector should not be on unless the cable is connected.

Note The link LEDs for the Fibre Channel ports remain yellow until the ports are enabled, and the LED for the Ethernet connector port remains off until the port is connected.

Step 7 Try removing and reinstalling a component that is not operating correctly. If it still does not operate correctly, contact your customer service representative for a replacement.

Note If you purchased this product through a Cisco reseller, contact the reseller directly for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL:http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.

Step 8 Verify that the system software has booted and the switch has initialized without error messages.

If any problems occur, see Appendix E, “Troubleshooting Hardware Components”. If you cannot resolve an issue, contact your customer service representative.

Step 9 Complete the worksheets provided in Appendix D, “Site Planning and Maintenance Records” for future reference.

Note A setup utility automatically launches the first time you access the switch and guides you through the basic configuration. For instructions on how to configure the switch and check module connectivity, see theCisco Nexus 5000 Series CLI Configuration Guide or theCisco Nexus 5000 Series Fabric Manager Configuration Guide.

Removing and Installing Components

This section includes the following topics:

Removing and Installing Expansion Modules, page 2-19

Removing and Installing Power Supplies, page 2-21

Removing and Installing the Fan Module, page 2-23

Removing the Cisco Nexus 5000 Switch, page 2-25

Caution To prevent ESD damage, wear grounding wrist straps during these procedures and handle modules by the carrier edges only.

 

Cisco Nexus 5000 Series Hardware Installation Guide

2-18

OL-15902-01

Chapter 2 Installing the Cisco Nexus 5000 Switch

Removing and Installing Components

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Removing and Installing Expansion Modules

Caution To prevent ESD damage, wear grounding wrist straps during these procedures and handle expansion modules by the carrier edges only.

Note Install the Cisco Nexus 5000 switch in the rack before installing expansion modules. For information about installing the chassis, see the“Installing the Cisco Nexus 5020 Chassis in a Cabinet or Rack” section on page 2-5 or“Installing the Cisco Nexus 5010 Chassis in a Cabinet or Rack” section on page 2-8

This section includes the following topics:

Installing an Expansion Module, page 2-19

Removing an Expansion Module, page 2-20

Installing an Expansion Module

To install an expansion module, follow these steps:

Step 1 Grasp the handle of the module and place your other hand under the module to support it.

Step 2 Gently slide the module into the opening until you cannot push it any further.

Step 3 Tighten the captive screw on the front of the module.

Figure 2-9 shows the positioning of an expansion module in the 5020 chassis.

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

2-19

 

 

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Removing and Installing Components

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure 2-9Positioning the Module in the Cisco Nexus 5020 Chassis

186598

Figure 2-10 shows the positioning of an expansion module in the 5010 chassis.

Figure 2-10Positioning the Module in the Cisco Nexus 5010 Chassis

273162

Removing an Expansion Module

To remove an expansion module from the chassis, follow these steps:

 

Cisco Nexus 5000 Series Hardware Installation Guide

2-20

OL-15902-01

Chapter 2 Installing the Cisco Nexus 5000 Switch

 

Removing and Installing Components

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

 

Step 1

Disconnect any network interface cables attached to the module.

Step 2

Loosen the captive screw on the module.

Step 3

Remove the module from the chassis by grasping the handle on the right side of the module and sliding

 

the module part of the way out of the slot. Place your other hand under the module to support the weight

 

of it. Do not touch the module circuitry.

Step 4

Place the module on an antistatic mat or antistatic foam if not immediately reinstalling it in another slot.

Step 5

Install a filler panel to keep dust out of the chassis and maintain consistent airflow if the slot will remain

 

empty.

 

 

 

Removing and Installing Power Supplies

The Cisco Nexus 5000 switch supports two front-endpower supplies, but it may be used with one power supply.

This section includes the following topics:

Removing a Power Supply, page 2-21

Note You can replace a faulty power supply while the system is operating provided the other power supply is functioning.

Removing a Power Supply

Caution If you are using the Cisco Nexus 5000 switch with one power supply, removing the power supply will cause the switch to shut down. If you are using two power supplies and you remove one of them, the switch will continue to operate.

To remove a power supply, follow these steps:

Step 1 Grasp the power supply handle with your left hand.

Step 2 Push against the release latch with your left thumb and slide the power supply out of the chassis. SeeFigure 2-11 andFigure 2-12.

Step 3 Place your right hand under the power supply to support it while you slide it out of the chassis.

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

2-21

 

 

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Removing and Installing Components

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Step 4 Install a blank power supply filler panel if the power supply bay is to remain empty.

Figure 2-11Removing the Power Supply for the Cisco Nexus 5020 switch

Figure 2-12Removing the Power Supply for the 5010

273163

Installing a Power Supply

To install a power supply, follow these steps:

Step 1 Ensure that the system (earth) ground connection has been made. For ground connection instructions, see the“Grounding the System” section on page 2-10.

 

Cisco Nexus 5000 Series Hardware Installation Guide

2-22

OL-15902-01

Chapter 2 Installing the Cisco Nexus 5000 Switch

Removing and Installing Components

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Step 2 If the power supply bay has a filler panel, press the latches on the sides of the filler panel, and then slide it out of the power supply bay.

Step 3 Hold the power supply by the handle and position it so that the release latch is on the right, and then slide it into the power supply bay, ensuring that the power supply is fully seated in the bay.

Step 4 Plug the power cable into the AC inlet connector at the rear of the chassis.

Note Depending on the outlet receptacle on your power distribution unit, you may need the optional jumper power cord to connect the Cisco Nexus 5000 switch to your outlet receptacle. See the“Jumper Power Cord” section on page C-10.

Step 5 Connect the other end of the power cable to an AC power source.

Caution In a system with dual power supplies, connect each power supply to a separate power source. In case of a power source failure, the second source will most likely still be available.

Step 6 Verify power supply operation by checking that the power supply LED is green

Removing and Installing the Fan Module

The fan module is designed to be removed and replaced while the system is operating without presenting an electrical hazard or damage to the system, provided the replacement is performed promptly.

This section includes the following topics:

Figure 2-14Fan Module for the Cisco Nexus 5010 switch, page 2-24

Installing a Fan Module, page 2-25

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

2-23

 

 

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Removing and Installing Components

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure 2-13 shows a fan module partially installed in the Cisco Nexus 5020 switch.

Figure 2-13Fan Module for the Cisco Nexus 5020 switch

186596

Figure 2-14showsa fan module partially installed in the Cisco Nexus 5010 switch.

Figure 2-14Fan Module for the Cisco Nexus 5010 switch

273164

Removing a Fan Module

Warning When removing the fan tray, keep your hands and fingers away from the spinning fan blades. Let the fan blades completely stop before you remove the fan tray.Statement 258

 

Cisco Nexus 5000 Series Hardware Installation Guide

2-24

OL-15902-01

Chapter 2 Installing the Cisco Nexus 5000 Switch

Removing and Installing Components

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

To remove a fan module, follow these steps:

Step 1 Loosen the captive screws on the fan module by turning them counterclockwise, using aflat-bladeor number 2 Phillips screwdriver if required.

Step 2 Grasp the handle of fan module and pull it outward.

Step 3 Pull the fan module clear of the chassis.

Installing a Fan Module

To install a fan module, follow these steps:

Step 1 Hold the fan module with the LED at the bottom.

Step 2 Place the fan module into the front chassis cavity so it rests on the chassis, and then push the fan module into the chassis as far as it can go and the captive screw makes contact with the chassis, and tighten the captive screw.

Step 3 Listen for the fans if the switch is powered on. You should immediately hear them operating. If you do not hear them, ensure that the fan module is inserted completely in the chassis and the faceplate is flush with the outside surface of the chassis.

Step 4 Verify that the LED is green. If the LED is not green, one or more fans are faulty. If this occurs, contact your customer service representative for a replacement part.

Note If you purchased this product through a Cisco reseller, contact the reseller directly for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL:http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.

Removing the Cisco Nexus 5000 Switch

Caution The slider rail and frontrack-mountbrackets do not have a stop mechanism when sliding in and out. If the front of the chassis is unfastened from the rack and the chassis slides forward on the slider rails, it may slip off the end of the rails and fall out of the rack.

To remove the Cisco Nexus 5000 switch from a rack, follow these steps:

Step 1 Ensure that the weight of the Cisco Nexus 5000 switch is fully supported and that the switch is being held by another person.

Step 2 Disconnect the power cord and the console cables.

Step 3 Disconnect all cables that are connected to SFP+ transceivers.

Step 4 Remove the screws fastening the frontrack-mountbrackets to the mounting rails.

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

2-25

 

 

 

 

 

Chapter 2 Installing the Cisco Nexus 5000 Switch

Repacking the Cisco Nexus 5000 Switch for Return Shipment

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Step 5 Gently slide the Cisco Nexus 5000 switch towards you, off of the slider rails and out of the rack.

Repacking the Cisco Nexus 5000 Switch for Return Shipment

If you need to return the Cisco Nexus 5000 switch, remove the switch from the rack by following the steps in “Removing the Cisco Nexus 5000 Switch” section on page 2-25,and repack it for shipment. If possible, use the original packing materials and container to repack the switch. Contact your Cisco customer service representative to arrange for return shipment to Cisco.

 

Cisco Nexus 5000 Series Hardware Installation Guide

2-26

OL-15902-01

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

C H A P T E R 3

Connecting the Cisco Nexus 5000 Switch

The Cisco Nexus 5000 switch provides the following types of ports:

Console port —AnRS-232port that you can use to create a local management connection.

Ethernet ports, both encrypted and unencrypted—Theseports can be used to connect to a LAN.

Fibre Channel ports—Theseports can be used to connect to a SAN.

Caution When running power and data cables in overhead or subfloor cable trays, Cisco Systems strongly recommends that power cables and other potential noise sources must be located as far away as practical from network cabling that terminates on Cisco Systems equipment. In situations where long parallel cable runs cannot be separated by at least 3.3 ft (1 m), Cisco Systems recommends shielding any potential noise sources by housing them in a grounded metallic conduit.

This chapter includes the following topics:

Preparing for Network Connections, page 3-2

Connecting to the Console Port, page 3-2

Connecting to the Ethernet Connector Port, page 3-3

Connecting to an Ethernet Port, page 3-4

Connecting to a Fibre Channel Port, page 3-7

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

3-1

 

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Preparing for Network Connections

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Preparing for Network Connections

When preparing your site for network connections to the Cisco Nexus 5000 switch, consider the following for each type of interface, and gather all the required equipment before connecting the ports:

Cabling required for each interface type

Distance limitations for each signal type

Additional interface equipment required

Connecting to the Console Port

The console port is an RS-232port with anRJ-45interface. (SeeFigure 3-1.)The console port is an asynchronous (async) serial port; any device connected to this port must be capable of asynchronous transmission.

We recommend using this port to create a local management connection to set the IP address and other initial configuration settings before connecting the switch to the network for the first time.

Caution The console port can be used to connect to a modem. If you do not connect it to a modem, connect it either before powering the switch on or after the switch has completed the boot process.

Figure 3-1 shows how to connect to the console port on the Cisco Nexus 5020 switch. The process is identical for the Cisco Nexus 5010 switch.

Figure 3-1Connecting to the Console Port on a Cisco Nexus 5000 Switch

186705

You can use the console port to perform the following:

Configure the Cisco Nexus 5000 switch from the CLI.

Monitor network statistics and errors.

Configure SNMP agent parameters.

Download software updates.

Cisco Nexus 5000 Series Hardware Installation Guide

3-2

OL-15902-01

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Connecting to the Ethernet Connector Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

You can use the console port to perform the following:

Configure the Cisco Nexus 5010 switch from the CLI.

Monitor network statistics and errors.

Configure SNMP agent parameters.

Download software updates.

Note To connect the console port to a computer terminal, the computer must support VT100 terminal emulation. The terminal emulation software (frequently an application such as HyperTerminal or Procomm Plus) makes communication between the Cisco Nexus 5000 switch and a computer possible during setup and configuration.

To connect the console port to a computer terminal, follow these steps:

Step 1 Configure the terminal emulator program to match the following default port characteristics: 9600 baud, 8 data bits, 1 stop bit, no parity.

Step 2 Connect theRJ-45connector of the console cable to the console port (seeFigure 3-1)and theDB-9connector to the computer serial port.

Note For configuration instructions, see the Cisco Nexus 5000 Series CLI Configuration Guide.

Connecting to the Ethernet Connector Port

Caution To prevent an IP address conflict, do not connect the management port to the network until the initial configuration is complete. For configuration instructions, see theCisco Nexus 5000 Series Switch Configuration Guide.

The Ethernet connector port has an RJ-45interface.

To connect the Ethernet connector port to an external hub, switch, or router, follow these steps:

Step 1 Connect the appropriate modular cable to the Ethernet connector port:

Use modular, RJ-45,straight-throughUTP cables to connect the Ethernet connector port to an Ethernet switch port or hub.

Use a cross-overcable to connect to a router interface.

Step 2 Connect the other end of the cable to the device.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

3-3

 

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Connecting to an Ethernet Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Connecting to an Ethernet Port

Use an SFP+ transceiver to connect to an Ethernet port, as described in this section.

Removing and Installing SFP+ Transceivers

Caution Excessively removing and installing an SFP transceiver can shorten its life. Do not remove and insert SFP transceivers more often unless it is absolutely necessary. We recommend disconnecting cables before installing or removing SFP transceivers to prevent damage to the cable or transceiver.

This section describes the proper method for installing and removing an SFP+ transceiver.

Installing an SFP+ Transceiver

To install an SFP+ transceiver, follow these steps:

Step 1 Attach anESD-preventivewrist strap and follow its instructions for use.

Step 2 Remove the dust cover from the port cage.

Step 3 Remove the dust cover from the port end of the transceiver.

Step 4 Insert the transceiver into the port:

If the transceiver has a Mylar tab, position the transceiver with the tab on the bottom, and then gently insert the transceiver into the port until it clicks into place.

If the transceiver has a bale clasp, position the transceiver with the clasp on the bottom, close the clasp by pushing it up over the transceiver, and then gently insert the transceiver into the port until it clicks into place.

Caution If the transceiver does not install easily, ensure that it is correctly positioned and the tab or clasp are in the correct position before continuing.

Note If you cannot install the cable into the transceiver, insert or leave the dust plug in the cable end of the transceiver.

Removing an SFP+ Transceiver

To remove an SFP+ transceiver, follow these steps:

Step 1 Attach anESD-preventivewrist strap and follow its instructions for use.

Step 2 If a cable is installed in the transceiver:

a. Record the cable and port connections for later reference.

Cisco Nexus 5000 Series Hardware Installation Guide

3-4

OL-15902-01

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Connecting to an Ethernet Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

b.Press the release latch on the cable, grasp the connector near the connection point, and gently pull the connector from the transceiver.

c.Insert a dust plug into the cable end of the transceiver.

Caution If the transceiver does not remove easily in the next step, push the transceiver completely in and then ensure that the latch is in the correct position before continuing.

Step 3 Remove the transceiver from the port:

If the transceiver has a Mylar tab latch, gently pull the tab straight out (do not twist), and then pull the transceiver out of the port.

If the transceiver has a bale clasp latch, open the clasp by pressing it downwards, and then pull the transceiver out of the port.

Note If you have difficulty removing a bale clasp SFP+ transceiver, you should reseat it by returning the bale clasp to the up position. Press the SFP+ transceiver inward and upward into the cage. Next, lower the bale clasp and pull the SFP+ transceiver straight out with a slight upward lifting force (seeFigure 3-2).Be careful not to damage the port cage during this process.

Figure 3-2Alternate Removal Method for Bale Clasp SFP+ Transceivers

186903

Step 4 Insert a dust cover into the port end of the transceiver and place the transceiver on an antistatic mat or into a static shielding bag if you plan to return it to the factory.

Step 5 If another transceiver is not being installed, protect the optical cage by inserting a clean cover.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

3-5

 

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Connecting to an Ethernet Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Removing and Installing Cables into SFP+ Transceivers

Caution To prevent damage to the copper cables, do not place more tension on them than the rated limit and do not bend to a radius of less than 1 inch if there is no tension in the cable, or 2 inches if there is tension in the cable.

Installing a Cable into an SFP+ Transceiver

Caution To prevent possible damage to the cable or transceiver, install the transceiver in the port before installing the cable in the transceiver.

To install a cable into a transceiver, follow these steps:

Step 1 Attach anESD-preventivewrist strap and follow its instructions for use.

Step 2 Remove the dust cover from the connector on the cable.

Step 3 Remove the dust cover from the cable end of the transceiver.

Step 4 Align the cable connector with the transceiver and insert the connector into the transceiver until it clicks into place.

Caution If the cable does not install easily, ensure that it is correctly positioned before continuing.

For instructions on verifying connectivity, see the Cisco Nexus 5000 Switch Configuration Guide.

Removing a Cable from an SFP+ Transceiver

 

 

 

Caution

When pulling a cable from a transceiver, grip the body of the connector. Do not pull on the jacket sleeve,

 

 

 

 

 

 

because this action can compromise the fiber-optictermination in the connector.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Caution

If the cable does not remove easily, ensure that any latch present on the cable has been released before

 

 

 

 

 

 

continuing.

 

 

 

 

 

 

 

 

 

 

 

 

 

To remove the cable, follow these steps:

 

 

 

 

 

 

 

 

 

 

Step 1

Attach an ESD-preventivewrist strap and follow its instructions for use.

 

 

 

 

Step 2

Press the release latch on the cable, grasp the connector near the connection point, and gently pull the

 

 

 

 

 

 

connector from the transceiver.

 

 

 

 

Step 3

Insert a dust plug into the cable end of the transceiver.

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

3-6

 

 

 

 

OL-15902-01

 

 

 

 

 

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Connecting to a Fibre Channel Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Step 4 Insert a dust plug onto the end of the cable.

Maintaining SFP+ Transceivers and Cables

SFP+ transceivers must be kept clean and dust-freeto maintain high signal accuracy and prevent damage to the connectors. Attenuation (loss of light) is increased by contamination and should be below 0.35 dB.

Consider the following maintenance guidelines:

SFP+ transceivers are static sensitive. To prevent ESD damage, wear an ESD-preventivewrist strap that is connected to the chassis.

Do not remove and insert a transceiver more often than is necessary. Repeated removals and insertions can shorten its useful life.

Keep all optical connections covered when not in use. If they become dusty, clean before using to prevent dust from scratching the fiber-opticcable ends.

Do not touch ends of connectors to prevent fingerprints and other contamination.

Clean regularly; the required frequency of cleaning depends upon the environment. In addition, clean connectors if they are exposed to dust or accidentally touched. Both wet and dry cleaning techniques can be effective; refer to your site’s fiber-opticconnection cleaning procedure.

Inspect routinely for dust and damage. If damage is suspected, clean and then inspect fiber ends under a microscope to determine if damage has occurred.

Connecting to a Fibre Channel Port

Use an SFP transceiver to connect to an Fibre Channel port.

Removing and Installing SFP Transceivers

Caution Excessively removing and installing an SFP transceiver can shorten its life. Do not remove and insert SFP transceivers more often unless it is absolutely necessary. Cisco recommends disconnecting cables before installing or removing SFP transceivers to prevent damage to the cable or transceiver.

This section describes the proper method for installing and removing an SFP transceiver.

Installing an SFP Transceiver

To install an SFP transceiver, follow these steps:

Step 1 Attach anESD-preventivewrist strap and follow its instructions for use.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

3-7

 

 

 

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

 

Connecting to a Fibre Channel Port

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

Step 2

Remove the dust cover from the port cage.

 

Step 3

Remove the dust cover from the port end of the transceiver.

 

Step 4

Insert the transceiver into the port:

If the transceiver has a Mylar tab, position the transceiver with the tab on the bottom, and then gently insert the transceiver into the port until it clicks into place.

If the transceiver has a bale clasp, position the transceiver with the clasp on the bottom, close the clasp by pushing it up over the transceiver, and then gently insert the transceiver into the port until it clicks into place.

Caution If the transceiver does not install easily, ensure that it is correctly positioned and the tab or clasp are in the correct position before continuing.

Note If you cannot install the cable into the transceiver, insert or leave the dust plug in the cable end of the transceiver.

Removing an SFP Transceiver

To remove an SFP transceiver, follow these steps:

Step 1 Attach anESD-preventivewrist strap and follow its instructions for use.

Step 2 If a cable is installed in the transceiver:

a.Record the cable and port connections for later reference.

b.Press the release latch on the cable, grasp the connector near the connection point, and gently pull the connector from the transceiver.

c.Insert a dust plug into the cable end of the transceiver.

Caution If the transceiver does not remove easily in the next step, push the transceiver completely in and then ensure that the latch is in the correct position before continuing.

Step 3 Remove the transceiver from the port:

If the transceiver has a Mylar tab latch, gently pull the tab straight out (do not twist), and then pull the transceiver out of the port.

If the transceiver has a bale clasp latch, open the clasp by pressing it downwards, and then pull the transceiver out of the port.

Note If you have difficulty removing a bale clasp SFP transceiver, you should reseat the SFP by returning the bale clasp to the up position. Press the SFP inward and upward into the cage. Next, lower the bale clasp and pull the SFP straight out with a slight upward lifting force (seeFigure 3-3).Be careful not to damage the port cage during this process.

Cisco Nexus 5000 Series Hardware Installation Guide

3-8

OL-15902-01

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Connecting to a Fibre Channel Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure 3-3Alternate Removal Method for Bale Clasp SFP Transceivers

186903

Step 4 Insert a dust cover into the port end of the transceiver and place the transceiver on an antistatic mat or into astatic-shieldingbag if you plan to return it to the factory.

Step 5 If another transceiver is not being installed, protect the optical cage by inserting a clean cover.

Removing and Installing Cables into SFP Transceivers

Caution To prevent damage to thefiber-opticcables, do not place more tension on them than the rated limit and do not bend to a radius of less than 1 inch if there is no tension in the cable, or 2 inches if there is tension in the cable.

Installing a Cable into an SFP Transceiver

 

Caution

To prevent possible damage to the cable or transceiver, install the transceiver in the port before installing

 

 

the cable in the transceiver.

 

 

 

 

 

To install a cable into a transceiver, follow these steps:

 

 

 

 

Step 1

Attach an ESD-preventivewrist strap and follow its instructions for use.

 

Step 2

Remove the dust cover from the connector on the cable.

 

Step 3

Remove the dust cover from the cable end of the transceiver.

 

Step 4

Align the cable connector with the transceiver and insert the connector into the transceiver until it clicks

 

 

into place. (See Figure 3-4).

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

OL-15902-01

 

 

3-9

 

 

 

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Connecting to a Fibre Channel Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure 3-4Connecting theLC-TypeCable to a Fibre Channel Port

LC plug

SFP module

91681

Caution If the cable does not install easily, ensure that it is correctly positioned before continuing.

For instructions on verifying connectivity, see the Cisco Nexus 5000 Series CLI Configuration Guide.

Removing a Cable from an SFP Transceiver

Caution When pulling a cable from a transceiver, grip the body of the connector. Do not pull on the jacket sleeve, because this action can compromise thefiber-optictermination in the connector.

Caution If the cable does not remove easily, ensure that any latch present on the cable has been released before continuing.

To remove the cable, follow these steps:

Step 1 Attach anESD-preventivewrist strap and follow its instructions for use.

Step 2 Press the release latch on the cable, grasp the connector near the connection point, and gently pull the connector from the transceiver.

Step 3 Insert a dust plug into the cable end of the transceiver.

Step 4 Insert a dust plug onto the end of the cable.

 

Cisco Nexus 5000 Series Hardware Installation Guide

3-10

OL-15902-01

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Connecting to a Fibre Channel Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Maintaining SFP Transceivers and Fiber-OpticCables

SFP transceivers and fiber-opticcables must be kept clean anddust-freeto maintain high signal accuracy and prevent damage to the connectors. Attenuation (loss of light) is increased by contamination and should be below 0.35 dB.

Consider the following maintenance guidelines:

SFP transceivers are static sensitive. To prevent ESD damage, wear an ESD-preventivewrist strap that is connected to the chassis.

Do not remove and insert a transceiver more often than is necessary. Repeated removals and insertions can shorten its useful life.

Keep all optical connections covered when not in use. If they become dusty, clean before using to prevent dust from scratching the fiber-opticcable ends.

Do not touch ends of connectors to prevent fingerprints and other contamination.

Clean regularly; the required frequency of cleaning depends upon the environment. In addition, clean connectors if they are exposed to dust or accidentally touched. Both wet and dry cleaning techniques can be effective; refer to your site’s fiber-opticconnection cleaning procedure.

Inspect routinely for dust and damage. If damage is suspected, clean and then inspect fiber ends under a microscope to determine if damage has occurred.

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-15902-01

 

 

3-11

 

 

 

 

 

Chapter 3 Connecting the Cisco Nexus 5000 Switch

Connecting to a Fibre Channel Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

Cisco Nexus 5000 Series Hardware Installation Guide

3-12

OL-15902-01

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

A P P E N D I X A

Cabinet and Rack Installation

This appendix provides the requirements for cabinet and rack installation and includes the following sections:

Cabinet and Rack Requirements, page A-1.

Cable Management Guidelines, page A-3

Cabinet and Rack Requirements

This section provides the requirements for the following types of cabinets and racks, assuming an external ambient air temperature range of 0 to 104oF (0 to 40oC):

Standard perforated cabinets

Solid-walledcabinets with a roof fan tray (bottom to top cooling)

Standard open racks

Note If you are selecting an enclosed cabinet, we recommend one of the thermally validated types: standard perforated orsolid-walledwith a fan tray.

Note Do not use racks that have obstructions (such as power strips), because the obstructions could impair access tofield-replaceableunits (FRUs).

General Requirements for Cabinets and Racks

The cabinet or rack must be one of the following types:

Standard 19-in.(48.3 cm)(four-postEIA cabinet or rack, with mounting rails that conform to English universal hole spacing per section 1 ofANSI/EIA-310-D-1992.See the“Requirements Specific to Perforated Cabinets” section on page A-2 and the“Requirements Specific to Solid-Walled Cabinets” section on page A-3.

The cabinet or rack must also meet the following requirements:

The minimum vertical rack space per 5020 chassis must be two RU (rack units), equal to 3.50 inches (8.9 cm).

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

A-1

 

Appendix A Cabinet and Rack Installation

Cabinet and Rack Requirements

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

The minimum vertical rack space per 5010 chassis must be one RU (rack unit), equal to 1.75 inches (4.4 cm).

The width between the rack-mountingrails must be at least 17.75 inches (45.1 cm) if the rear of the switch is not attached to the rack. Forfour-postEIA racks, this is the distance between the two front rails.

For four-postEIA cabinets (perforated orsolid-walled):

The minimum spacing for the bend radius for fiber-opticcables should have thefront-mountingrails of the cabinet offset from the front door by a minimum of 3 inches (7.6 cm), and a minimum of 5 inches (12.7 cm) if cable management brackets are installed on the front of the chassis.

The distance between the outside face of the front mounting rail and the outside face of the back mounting rail should be 23.5 to 34.0 inches (59.7 to 86.4 cm) to allow for rear-bracketinstallation.

A minimum of 2.5 inches (6.4 cm) of clear space should exist between the side edge of the chassis and the side wall of the cabinet. No sizeable flow obstructions should be immediately in the way of chassis air intake or exhaust vents.

Note Optional jumper power cords are available for use in a cabinet. See the“Jumper Power Cord” section on page C-10.

Requirements Specific to Perforated Cabinets

A perforated cabinet is defined here as a cabinet with perforated front and rear doors and solid side walls. In addition to the requirements listed in the “General Requirements for Cabinets and Racks” section on page A-1,perforated cabinets must meet the following requirements:

The front and rear doors must have at least a 60 percent open area perforation pattern, with at least 15 square inches of open area per rack unit of door height.

The roof should be perforated with at least a 20 percent open area.

The cabinet floor should be open or perforated to enhance cooling.

A perforated cabinet that conforms to these requirements is available from Rittal Corporation:

Rittal Corporation

One Rittal Place

Springfield, OH 45504

Contact: (800) 477–4220

Cabinet P/N: Rittal 9969427

Cabinet description: PS-DK/OEMCabinet Assembly, (78.7 in.) 1998 mm X 23.6 in. (600 mm) X 39.4 in. (1000 mm) (H x W x D) (42 RU)

Cisco Nexus 5000 Series Hardware Installation Guide

 

A-2

OL-15902-01

 

 

 

Appendix A Cabinet and Rack Installation

Cable Management Guidelines

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Requirements Specific to Solid-WalledCabinets

A solid-walledcabinet is defined here as a cabinet with solid front and rear doors and solid side walls. In addition to the requirements listed in the“General Requirements for Cabinets and Racks” section on page A-1,solid-walledcabinets must meet the following requirements:

A roof-mountedfan tray and an air cooling scheme in which the fan tray pulls air in at the bottom of the cabinet and exhausts it out the top, with a minimum of 500 cubic feet per minute of airflow exiting the cabinet roof through the fan tray.

Nonperforated (solid and sealed) front and back doors and side panels so that air travels predictably from bottom to top.

A recommended cabinet depth of 36 to 42 inches (91.4 to 106.7 cm) to allow the doors to close and for adequate airflow.

A minimum of 150 sq. inches (968 sq. cm) of open area at the floor air intake of the cabinet.

The lowest piece of equipment should be installed a minimum of 1.75 inches (4.4 cm) above the floor openings to prevent blocking the floor intake.

Requirements Specific to Standard Open Racks

In addition to the requirements listed in the “General Requirements for Cabinets and Racks” section on page A-1, if mounting the chassis in an open rack (no side panels or doors), ensure that the rack meets the following requirements:

The minimum vertical rack space per chassis must be two RU (rack unit), equal to 3.47 inches (8.8 cm).

The horizontal distance between the chassis and any adjacent chassis should be 6 inches(15.2 cm), and the distance between the chassis air vents and any walls should be 2.5 inches (6.4 cm).

Cable Management Guidelines

To help with cable management, you might want to allow additional space in the rack above and below the chassis to make it easier to route as many as 56 fiber or copper cables through the rack.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

A-3

 

Appendix A Cabinet and Rack Installation

Cable Management Guidelines

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Cisco Nexus 5000 Series Hardware Installation Guide

 

A-4

OL-15902-01

 

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

A P P E N D I X B

Technical Specifications

This appendix includes the following sections:

Switch Specifications, page B-1

Expansion Module Specifications, page B-2

Power Specifications, page B-2

Transceiver Specifications, page B-4

Note Specifications for cables and connectors are provided inAppendix C, “Cable and Port Specifications.”

Switch Specifications

Table B-1 lists the physical specifications for the Cisco Nexus 5020 switch.

Table B-1

Physical Specification for the Cisco Nexus 5020 Switch

 

 

 

Description

 

Specification

 

 

Dimensions (H x W x D)

3.47 in (8.8 cm) x 17.3 in (43.9 cm) x 30.0 in

 

 

(76.2 cm)

 

 

Weight (with two power supplies and two

50 lb (22.680 kg)

expansion modules installed)

 

 

 

 

Table B-2 lists the physical specifications for the Cisco Nexus 5010 switch.

Table B-2

Physical Specification for the Cisco Nexus 5010 Switch

 

 

 

Description

 

Specification

 

 

Dimensions (H x W x D)

1.72 in x 17.3 in (43.9 cm) x 30.0 in (76.2 cm)

 

 

Weight (with two power supplies and one

35 lb (15.875 kg)

expansion module installed)

 

 

 

 

Table B-3 lists the environmental specifications for the Cisco Nexus 5000 switch.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

B-1

 

 

 

 

 

Appendix B Technical Specifications

 

Expansion Module Specifications

 

 

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

 

Table B-3

Environmental Specifications for the Cisco Nexus 5020 Switch

 

 

 

 

 

 

 

 

Description

 

Specification

 

 

 

 

 

 

 

Temperature, operating

32 to 104°F (0 to 40°C)

 

 

 

 

 

 

 

Temperature, nonoperating

-40to 158°F(-40to 70°C)

 

 

 

 

 

 

 

Humidity (RH), noncondensing

5 to 95%

 

 

 

 

 

 

 

 

Altitude

 

0 to 10000 ft (0 to 3000 m)

 

 

 

 

 

 

Expansion Module Specifications

Table B-4Physical Specifications for the Cisco Nexus 5020 Switch Expansion Modules

Description Specification

Weight

1 lb (0.5 kg)

Power Specifications

This section includes the following topics:

Specifications for the Cisco Nexus 5020 Power Supply, page B-2

Specifications for the Cisco Nexus 5010 Power Supply, page B-3

Power Supply LED Indicators, page B-3

Specifications for the Cisco Nexus 5020 Power Supply

Table B-5 lists the specifications for the Cisco Nexus 5020 power supply.

Table B-5Specifications for the Cisco Nexus 5020 Power Supply

Description

Specification

 

 

AC-inputvoltage (VinHigh)

Minimum = 90 Vrms

 

Rated = 100 to 240 Vrms

 

Maximum = 264 Vrms

 

 

AC-inputfrequency (VinFrequency)

Minimum = 47 Hz

 

Rated = 50 to 60 Hz

 

Maximum = 63 Hz

 

 

Maximum power

750 W

 

 

Typical power

480 W

 

 

Power supply output voltage

12 V

 

 

Dimensions (H x W x D)

1.57 in (0.039m) x 4.00 in (0.101m) x 13.00 in (.330m)

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

B-2

OL-15902-01

 

 

 

Appendix B Technical Specifications

Power Specifications

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

The current power supply in the Nexus 5020 has a label for 200-240V.However, it has since been certified to support 110V input as well. As a result, both 110V and 220V inputs are supported and the labels on the chassis moving forwards will reflect this capability. A new software release will be required to support this capability.

Specifications for the Cisco Nexus 5010 Power Supply

The power supplies connect to the system through panel mount connectors and connectors attach to the baseboard through cables. There are total of 3 connectors on the baseboard, two for power delivery, and one for power supply control signals.Table B-6 lists the specifications for the Cisco Nexus 5010 power

supply.

Table B-6

Specifications for the Cisco Nexus 5010 Power Supply

 

 

 

Description

 

Specification

 

 

 

Rated power

 

550W

 

 

 

Input voltage

 

90-264VAC

 

 

 

Frequency

 

47-63Hz

 

 

PSU Control Interface

I2C

 

 

ROHS Compliant

Yes

 

 

Size (W x H x D)

2.75 x 1.57 x 13.7 (in)

 

 

 

Cubic Inches

 

59

 

 

 

Power Density

 

9.3 W / in3

 

 

Operating Temperature

0 oC to 50oC

 

 

 

Cooling

 

Internal fans to cool the supply

 

 

 

Input connector

 

AC connector in the chassis

 

 

Output connector

DC output connector in the back

 

 

Hot plug capable

Yes

 

 

Supply Indicators

Supply Health: Green indicates supply is good and Amber

 

 

indicates a fault.

 

 

AC good indicator: Green indicating AC is present and

 

 

is within the supply spec

 

 

 

Power Supply LED Indicators

Table B-7 lists the LED indicators for the LED on the front of the power supply.

 

 

Table B-7

Power Supply LED Indicators

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Condition

 

Power LED Status (Green)

Fail LED Status (Amber)

 

 

 

 

 

 

 

 

No AC power to the power supplies

Off

Off

 

 

 

 

 

 

 

 

Power supply failure (includes over

Off

On

 

 

voltage, over current, over

 

 

 

 

 

 

 

 

temperature, and fan failure)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-15902-01

 

 

 

 

B-3

 

 

 

 

 

 

 

 

 

 

 

 

Appendix B Technical Specifications

 

Transceiver Specifications

 

 

 

 

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

 

Table B-7

Power Supply LED Indicators

 

 

 

 

 

 

 

 

 

 

 

 

 

Condition

 

Power LED Status (Green)

 

Fail LED Status (Amber)

 

 

 

 

 

 

 

 

 

Power supply warning events where

Off

 

1 Hz blinking

 

 

the power supply continues to operate

 

 

 

 

 

 

(high temperature, high power, and

 

 

 

 

 

 

slow fan)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AC present / 3.3 voltage standby

1 Hz blinking

 

Off

 

 

(VSB) on, and power supply unit off

 

 

 

 

 

 

 

 

 

 

 

 

 

Power supply On and OK

On

 

Off

 

 

 

 

 

 

 

 

Transceiver Specifications

Table B-8 lists general specifications for the10-GigabitEthernet SFP+ transceiver module.

Table B-8

General Specifications for the 10-GigabitEthernet SFP+ Transceiver Module

 

 

 

 

 

 

Description

 

 

Short Range

 

 

 

 

 

 

Connector type

 

LC

 

 

 

 

 

 

 

 

 

Wavelength

 

850 nm

 

 

 

 

 

 

 

 

 

Core size

 

50 microns

 

62.5 microns

 

 

 

 

 

 

Cable distance

 

300 m

 

33 m

 

 

 

 

 

 

Environmental Conditions and Power Requirement Specifications for SFP+ Transceivers

Table B-9 lists the environmental conditions and power requirement specifications for the10-GigabitEthernet SFP+ transceiver module.

Table B-9Environmental Conditions and Power Requirement Specifications for the10-GigabitEthernet SFP+ Transceiver Module

Parameter

Symbol

Min.

Max.

Unit

 

 

 

 

 

Storage temperature

TS

-40

 

ºC

Case temperature

TC

0

70

ºC

Relative humidity

RH

 

 

 

 

 

 

 

 

Module supply voltage

VCCT,R

3.1

3.5

V

General Specifications for Cisco Fibre Channel SFP Transceivers

Table B-10 lists the general specifications for Cisco Fibre Channel SFP transceivers at 4 Gbps.

Cisco Nexus 5000 Series Hardware Installation Guide

 

B-4

OL-15902-01

 

 

 

Appendix B Technical Specifications

Transceiver Specifications

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Table B-10

General Specifications for Cisco Fibre Channel SFP Transceivers at 4 Gbps

 

 

 

 

Description

 

Short Wavelength

 

 

 

 

 

Connector type

 

LC

 

 

 

 

 

Wavelength

 

850 nm

 

 

 

 

 

Fibre type

 

MMF

 

 

 

 

 

Core size

 

50 microns

62.5 microns

 

 

 

 

Cable distance1

 

328.08 yd (300 m)

164.04 yd (150 m)

Transmit power

 

-9to-2.5dBM

 

 

 

 

 

1. Approximate; actual distance may vary depending on fiber quality and other factors.

Environmental Conditions and Power Requirements Specification for SFP Transceivers

Table B-11 provides the maximum environmental and electrical ratings for Cisco Fibre Channel SFP transceivers.

Table B-11

Environmental Conditions and Power Requirements Specifications for SFP

 

Transceivers

 

 

 

 

 

 

 

 

 

 

Parameter

 

Symbol

Min.

Max.

Unit

 

 

 

 

 

Storage temperature1

TS

-40

85

ºC

Case temperature1,2

TC

0

70

ºC

Relative humidity1

RH

5

95

%

Module supply voltage1

VCCT,R

3.1

3.5

V

1.Absolute maximum ratings are those values beyond which damage to the device may occur if these limits are exceeded for other than a short period of time.

2.Functional performance is not intended, device reliability is not implied, and damage to the device may occur over an extended period of time between absolute maximum ratings and the recommended operating conditions.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

B-5

 

Appendix B Technical Specifications

Transceiver Specifications

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Cisco Nexus 5000 Series Hardware Installation Guide

 

B-6

OL-15902-01

 

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

A P P E N D I X C

Cable and Port Specifications

This appendix provides cable and port specifications, and includes the following sections:

Accessory Kit for the Cisco Nexus 5020 Switch, page C-1

Accessory Kit for the Cisco Nexus 5010 Switch, page C-1

Console Port, page C-3

Supported Power Cords and Plugs, page C-4

Jumper Power Cord, page C-10

Accessory Kit for the Cisco Nexus 5020 Switch

The Cisco Nexus 5020 switch accessory kit includes the following items:

2 slider rails

2 rack-mountguides

2 rack-mountbrackets

16 M4 x 0.7 x 8-mmPhillips countersunk screws

12 10-32rack nuts

12 10-32x3/4-inchPhillips countersunk screws

1 console cable with an RJ-45-RS-232adapter and a DB9 adapter

1 ground lug kit

1 ESD wrist strap

Note Additional parts can be ordered from your customer service representative.

Accessory Kit for the Cisco Nexus 5010 Switch

The Cisco Nexus 5010 switch accessory kit includes the following items:

2 slider rails

2 rack-mountguides

2 rack-mountbrackets

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

C-1

 

Appendix C Cable and Port Specifications

Console Cable

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

12 M4 x 0.7 x 8-mmPhillips countersunk screws

10 10-32rack nuts

10 10-32x3/4-inchPhillips countersunk screws

1 console cable with an RJ-45-RS-232adapter and a DB9 adapter

1 ground lug kit

1 ESD wrist strap

Note Additional parts can be ordered from your customer service representative.

Console Cable

The console cable has a RJ-45,RS-232connector on one end and a DB9 connector on the other end. SeeFigure C-1.

Figure C-1

Console Cable

187491

Cable RJ-45Connector Pinouts

Table C-1 lists the pinouts for theRJ-45connector on the console cable.

 

 

 

 

Table C-1

Cable Connector Pinouts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal Name

 

P1, P1-45Pins

P2, DB-9Pins

Signal Name

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RTS

 

1

8

CTS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DTR

 

2

6

DSR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TXD

 

3

2

ZXD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND

 

4

5

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND

 

5

5

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZXD

 

6

3

TXD

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C-2

 

 

 

 

 

 

OL-15902-01

 

 

 

 

 

 

 

 

 

Appendix C Cable and Port Specifications

Console Port

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Table C-1

Cable Connector Pinouts

 

 

 

 

 

 

 

Signal Name

 

P1, P1-45Pins

P2, DB-9Pins

Signal Name

 

 

 

 

 

DSR

 

7

4

DTR

 

 

 

 

 

CTS

 

8

7

RTS

 

 

 

 

 

Console Port

The console port is an asynchronous RS-232serial port with anRJ-45connector.

Console Port Pinouts

Table C-2 lists the pinouts for the console port on the Cisco Nexus 5020 switch.

Table C-2

Console Port Pinouts

 

 

 

Pin

Signal

 

 

 

1

RTS

 

 

 

2

DTR

 

 

 

3

TxD

 

 

 

4

GND

 

 

 

5

GND

 

 

 

6

RxD

 

 

 

7

DSR

 

 

 

8

CTS

 

 

 

Table C-3 lists the pinouts for the console port on the Cisco Nexus 5010 switch.

Table C-3

Console Port Pinouts

 

 

 

Pin

Signal

 

 

 

1

RTS

 

 

 

2

DTR

 

 

 

3

TxD

 

 

 

4

GND

 

 

 

5

GND

 

 

 

6

RxD

 

 

 

7

DSR

 

 

 

8

CTS

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

C-3

 

Appendix C Cable and Port Specifications

Supported Power Cords and Plugs

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Supported Power Cords and Plugs

Each power supply has a separate power cord. Standard power cords or jumper power cords are available for connection to a power distribution unit having IEC 60320 C19 outlet receptacles. The jumper power cords, for use in cabinets, are available as an optional alternative to the standard power cords.

Power Cords

The standard power cords have an IEC C19 connector on the end that plugs into the switch. The optional jumper power cords have an IEC C19 connector on the end that plugs into the switch, and an IEC C20 connector on the end that plugs into an IEC C19 outlet receptacle.

Note Only the regular power cords or jumper power cords provided with the switch are supported.

Table C-4 lists the power cords for the Cisco Nexus 5020 switch and provides their lengths in feet and meters.

 

 

 

 

Table C-4

Power Cords for the Cisco Nexus 5020 Switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Length

 

Power Cord Reference

 

 

 

 

 

 

 

 

 

 

 

 

Description

 

Feet

Meters

Illustration

 

 

 

 

 

 

 

 

 

 

 

 

SFS-250V-10A-AR

8.2

2.5

Figure C-2

 

 

 

 

Power Cord, 250 VAC 10 A IRAM 2073 Plug

 

 

 

 

 

 

 

 

Argentina

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAB-9K10A-AU

8.2

2.5

Figure C-3

 

 

 

 

250 VAC 10 A 3112 Plug,

 

 

 

 

 

 

 

 

Australia

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SFS-250V-10A-CN

8.2

2.5

Figure C-4

 

 

 

 

Power Cord, 250 VAC 10 A GB 2009 Plug

 

 

 

 

 

 

 

 

China

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAB-9K10A-EU

8.2

2.5

Figure C-5

 

 

 

 

Power Cord, 250 VAC 10 A M 2511 Plug

 

 

 

 

 

 

 

 

Europe

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SFS-250V-10A-ID

8.2

2.5

Figure C-6

 

 

 

 

Power Cord, 250 VAC 16A EL-208Plug

 

 

 

 

 

 

 

 

South Africa, United Arab Emerits, India

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SFS-250V-10A-IS

8.2

2.5

Figure C-7

 

 

 

 

Power Cord, 250 VAC 10 A SI32 Plug

 

 

 

 

 

 

 

 

Israel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAB-9K10A-IT

8.2

2.5

Figure C-8

 

 

 

 

Power Cord, 250 VAC 10 A CEI 23-16Plug

 

 

 

 

 

 

 

 

Italy

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAB-9K10A-SW

8.2

2.5

Figure C-9

 

 

 

 

Power Cord, 250 VAC 10 A MP232 Plug

 

 

 

 

 

 

 

 

Switzerland

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C-4

 

 

 

 

 

 

OL-15902-01

 

 

 

 

 

 

 

 

 

Appendix C Cable and Port Specifications

Supported Power Cords and Plugs

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Table C-4

Power Cords for the Cisco Nexus 5020 Switch (continued)

 

 

 

 

 

 

 

 

Length

 

Power Cord Reference

 

 

 

 

Description

 

Feet

Meters

Illustration

 

 

 

 

CAB-9K10A-UK

8.2

2.5

Figure C-10

Power Cord, 250 VAC 10 A BS1363 Plug (13 A

 

 

 

fuse)

 

 

 

 

United Kingdom

 

 

 

 

 

 

 

CAB-AC-250V/13A

6.6

2.0

Figure C-11

Power Cord, 250 VAC 13 A IEC60320 Plug

 

 

 

North America

 

 

 

 

 

 

 

 

CAB-N5K6A-NA

8.2

2.5

Figure C-12

Power Cord, 250 VAC 13 A NEMA 6-15Plug,

 

 

 

North America

 

 

 

 

 

 

 

 

CAB-C13-C14-JMPR

2.2

0.7

Figure C-16

Cabinet Jumper Power Cord, 250 VAC 13 A,

 

 

 

C14-C15Connectors

 

 

 

 

 

 

 

 

AC Power Cord Illustrations

This section contains the AC power cord illustrations.

Figure C-2

SFS-250V-10A-AR

 

 

2500 mm

 

 

Cordset rating: 10 A, 250/500 V MAX

 

 

Length: 8.2 ft

 

Plug:

 

 

EL 219

 

 

(IRAM 2073)

Connector:

 

 

EL 701

 

 

(IEC60320/C13)

186571

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

C-5

 

Appendix C Cable and Port Specifications

Supported Power Cords and Plugs

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure C-3

CAB-9K10A-AU

 

 

 

Cordset rating: 10 A, 250 V/500V

 

 

 

Length: 2500mm

 

 

 

Plug:

Connector:

 

 

EL 701C

 

 

EL 206

 

 

(IEC 60320/C15)

186581

 

A.S. 3112-2000)

 

 

 

 

 

Figure C-4

SFS-250V-10A-CN

 

 

Plug:

Cordset rating 10A, 250V

EL 218

(2500 mm)

(CCEE GB2009)

 

 

Connector:

 

 

 

 

 

EL 701

 

186573

 

 

 

(IEC60320/C13)

 

 

 

 

 

 

Figure C-5

CAB-9K10A-EU

 

 

 

 

 

 

Cordset rating: 10A/16 A, 250 V

 

 

 

 

Plug:

Length: 8 ft 2 in. (2.5 m)

 

 

 

 

 

 

 

 

 

M2511

 

 

 

 

 

 

 

Connector:

 

 

 

 

VSCC15

186576

 

 

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

C-6

OL-15902-01

 

 

 

Appendix C Cable and Port Specifications

Supported Power Cords and Plugs

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure C-6SFS-250V-10A-ID

OVE

Plug:

Cordset rating 16A, 250V

EL 208

(2500mm)

 

Connector:

 

EL 701

 

187490

Figure C-7

SFS-250V-10A-IS

EL-212

 

16A

 

250V

 

 

Cordset rating 10A, 250V/500V MAX

 

(2500 mm)

 

Connector:

Plug:

EL 701B

(IEC60320/C13)

EL 212

186574

(SI-32)

 

Figure C-8

CAB-9K10A-IT

 

 

 

 

 

 

 

 

 

 

 

 

 

Cordset rating: 10 A, 250 V

 

Plug:

Length: 8 ft 2 in. (2.5 m)

Connector

 

 

I/3G

 

 

C15M

(CEI 23-16)

 

 

(EN60320/C15 )

113375

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

C-7

 

Appendix C Cable and Port Specifications

Supported Power Cords and Plugs

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Figure C-9

CAB-9K10A-SW

 

 

 

Cordset rating: 10 A, 250 V

 

Plug:

Length: 2500mm

 

 

 

MP232-R

Connector:

 

 

 

 

VSCC15 BKR

 

 

186578

Figure C-10

CAB-9K10A-UK

 

 

Cordset rating: 10 A, 250 V/500 V MAX

 

 

 

Length: 2500mm

 

 

 

 

Connector:

 

 

Plug:

EL 701C

 

 

EL 210

(EN 60320/C15)

186580

 

(BS 1363A) 13 AMP fuse

 

 

 

 

Figure C-11

CAB-AC-250V/13A

 

 

 

 

Cordset rating 13A, 250V

 

 

 

(6.6 feet) (79±2m)

 

 

Plug:

Connector:

 

 

EL 701

 

EL312MoldedTwistlock

 

(IEC60320/C13)

186568

(NEMA L6-20)

 

 

 

 

Figure C-12

CAB-N5K6A-NA

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

C-8

OL-15902-01

 

 

 

Appendix C Cable and Port Specifications

Supported Power Cords and Plugs

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

 

Cordset rating: 10 A, 250 V

 

Plug: NEMA 6-15P

Length: 8.2 ft

 

 

 

Connector:

 

 

 

EL 701

186570

 

 

(IEC60320/C13)

 

 

 

Figure C-13

CAB-9K12A-NA

 

 

 

Cordset rating 13A, 125V

 

 

 

(8.2 feet) (2.5m)

 

 

Plug:

Connector

 

EL 302 (NEMA 5-15P)

EL701C (IEC60320/C15)

192260

 

 

 

Figure C-14

CAB-C13-CBN

 

 

Plug:

SS10A

Cordset rating 10A, 250V (686mm)

Connector:

HS10S

186569

Figure C-15CAB-IND-10A

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

C-9

 

Appendix C Cable and Port Specifications

Jumper Power Cord

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

 

 

Cordset rating 10A, 250V

 

 

(8.2 feet) (2.5m)

 

Plug:

Connector

 

EL 208B (IS 6538-1971)

EL701B (IEC60320/C13)

192259

 

 

Jumper Power Cord

Figure C-16 shows the plug connector on the optional jumper power cord for the Cisco Nexus 5020 switch. The plug plugs into the Cisco Nexus 5020 switch power supply, while the connector plugs into the receptacle of a power distribution unit for a cabinet.

Figure C-16

CAB-C13-C14-JMPR,Jumper Power Cord

 

 

Cordset rating 10A, 250V

 

 

(686mm)

 

Plug:

Connector:

 

HS10S

186569

SS10A

 

 

 

Cisco Nexus 5000 Series Hardware Installation Guide

 

C-10

OL-15902-01

 

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

A P P E N D I X D

Site Planning and Maintenance Records

This appendix includes the following records to use when installing the Cisco Nexus 5000 switch:

Site Preparation Checklist, page D-1

Contact and Site Information, page D-3

Chassis and Module Information, page D-4

Note For information about how to query the switch for configuration information, see theCisco Nexus 5000 Switch Configuration Guide.

Site Preparation Checklist

Planning the location and layout of your equipment rack or wiring closet is essential for successful switch operation, ventilation, and accessibility. Table D-1 lists the site planning tasks that we recommend completing before installing the Cisco Nexus 5000 switch.

Consider heat dissipation when sizing the air-conditioningrequirements for an installation. SeeTable B-3 on page B-2 for the environmental requirements, and the“Power Specifications” section on page B-2 for power and heat ratings.

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

D-1

 

Appendix D Site Planning and Maintenance Records

Site Preparation Checklist

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Table D-1

 

Site Planning Checklist

 

 

 

 

 

 

 

 

Task No.

Planning Activity

Verified By

Time

Date

 

 

 

 

 

1

Space evaluation:

 

 

 

 

Space and layout

 

 

 

 

Floor covering

 

 

 

 

Impact and vibration

 

 

 

 

Lighting

 

 

 

 

Maintenance access

 

 

 

 

 

 

 

 

2

Environmental evaluation:

 

 

 

 

Ambient temperature

 

 

 

 

Humidity

 

 

 

 

Altitude

 

 

 

 

Atmospheric contamination

 

 

 

 

Air flow

 

 

 

 

 

 

 

 

3

Power evaluation:

 

 

 

 

Input power type

 

 

 

 

Power receptacles1

 

 

 

 

Receptacle proximity to the

 

 

 

 

 

equipment

 

 

 

 

Dedicated circuit for power supply

 

 

 

 

Dedicated (separate) circuits for

 

 

 

 

 

redundant power supplies

 

 

 

 

UPS2 for power failures

 

 

 

4

Grounding evaluation:

 

 

 

 

Circuit breaker size

 

 

 

 

CO ground (ACpowered systems)

 

 

 

 

 

 

 

 

5

Cable and interface equipment

 

 

 

 

evaluation:

 

 

 

 

Cable type

 

 

 

 

Connector type

 

 

 

 

Cable distance limitations

 

 

 

 

Interface equipment (transceivers)

 

 

 

 

 

 

 

 

6

EMI3 evaluation:

 

 

 

 

Distance limitations for signaling

 

 

 

 

Site wiring

 

 

 

 

RFI4 levels

 

 

 

1.Verify that the power supply installed in the chassis has a dedicated AC source circuit.

2.UPS = uninterruptible power supply.

Cisco Nexus 5000 Series Hardware Installation Guide

 

D-2

OL-15902-01

 

 

 

Appendix D Site Planning and Maintenance Records

Contact and Site Information

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

3.EMI = electromagnetic interference.

4.RFI = radio frequency interference.

Contact and Site Information

Use the following worksheet (Table D-2)to record contact and site information.

Table D-2Contact and Site Information

Contact person

Contact phone

Contact e-mail

Building/site name

Data center location

Floor location

Address (line 1)

Address (line 2)

City

State

Zip code

Country

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

D-3

 

Appendix D Site Planning and Maintenance Records

Chassis and Module Information

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Chassis and Module Information

Use the following worksheets (Table D-3 andTable D-4)to record information about the chassis and modules.

Contract Number_______________________________________________

Chassis Serial Number___________________________________________

Product Number________________________________________________

Table D-3Network-RelatedInformation

Switch IP address

Switch IP netmask

Host name

Domain name

IP broadcast address

Gateway/router address

DNS address

Modem telephone number

Table D-4Module Information

Slot Module Type

Module Serial Number

Notes

1

Supervisor

2

Note The supervisor module and the interface module are not removable.

Cisco Nexus 5000 Series Hardware Installation Guide

 

D-4

OL-15902-01

 

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

A P P E N D I X E

Troubleshooting Hardware Components

This appendix describes how to identify and resolve problems that might occur with the hardware components of the Cisco Nexus 5000 switch. It includes the following sections:

Overview, page E-1

SNMP Traps, page E-1

Switch Hardware Best Practices, page E-1

Overview

The key to success when troubleshooting the system hardware is to isolate the problem to a specific system component. The first step is to compare what the system is doing to what it should be doing. Because a startup problem can usually be attributed to a single component, it is more efficient to isolate the problem to a subsystem rather than troubleshoot each separate component in the system.

Problems with the initial power up are often caused by a module that is not firmly connected to the backplane or a power supply that has been disconnected from the power cord connector.

Overheating can also cause problems with the system, though typically only after the system has been operating for an extended period of time. The most common cause of overheating is the failure of a fan module.

SNMP Traps

You can set SNMP traps to monitor fans, power supplies, and temperature settings, or to test a call home application. Use the following commands to set SNMP traps:

test pfmtest-SNMP-trapfan

test pfmtest-SNMP-trappower supply

test pfmtest-SNMP-traptemp-sensor

Switch Hardware Best Practices

Use the recommendations in this section to ensure the proper installation, initialization, and operation of the switch. This section includes the following topics:

Cisco Nexus 5000 Series Hardware Installation Guide

 

OL-15902-01

E-1

 

Appendix E Troubleshooting Hardware Components

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Installation Best Practices

When installing the switch, follow these best practices:

Plan your site configuration and prepare the site before installing the chassis.

Verify that you have the appropriate power supplies for your chassis configuration.

Install the chassis following the rack and airflow guidelines presented in this guide.

Verify that the chassis is adequately grounded.

Initialization Best Practices

When the initial system boot is complete, verify the following:

Power supplies are supplying power to the system. See the

Fan modules are operating normally. See the

The system software boots successfully. See the Cisco Nexus 5020 CLI Configuration Guide for information about booting the system and initial configuration task.

Switch Operation Best Practices

To ensure proper operation of your switch, take the following actions:

Make a copy of the running configuration to CompactFlash for a safe backup.

Always enter the copy running-config startup-config CLI command after you modify the running configuration and ensure that the system is operating properly.

Never use the init system CLI command unless you understand that you will lose the running and startup configuration as well as the files stored on bootflash:.

Keep backup copies of the running kickstart and the system images on CompactFlash.

Cisco Nexus 5000 Series Hardware Installation Guide

 

E-2

OL-15902-01

 

 

 

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

I N D E X

Numerics

10-GigabitEthernet SFP+ transceivers

copper cables

1-14, 1-29

description

1-14, 1-29

A

accessory kit contents C-1

B

brackets

front rack-mount2-6, 2-9

C

cabinets

 

 

 

 

perforated (requirements)

A-2

 

solid-walled(requirements)

A-3

 

cabling

 

 

 

 

requirements 3-1

 

 

 

chassis

 

 

 

 

airflow considerations

2-2

 

 

description

1-2, 1-16

 

 

 

dimensions

1-2, B-1

 

 

 

grounding

2-15

 

 

 

installation guidelines

2-3

 

 

installing in a rack (procedure)

2-6, 2-9

removing from rack (procedure)

2-25

system grounding 2-10

 

 

 

weight 2-2, B-1

 

 

 

Cisco Nexus 5020 switch

 

 

 

connecting a system ground

2-14

 

description

 

1-1, 1-16

 

 

 

dimensions

 

1-2, 1-16, B-1

 

 

expansion modules

1-5, 1-20

 

 

fan module

 

1-10, 1-26

 

 

features

1-1, 1-16

 

 

 

front view

1-2, 1-17

 

 

 

grounding the chassis

2-15

 

 

installing in a cabinet

2-5, 2-8

 

installing in a rack 2-5, 2-8

 

 

LEDs 1-12, 1-27

 

 

 

port grouping

1-8, 1-23

 

 

port numbering 1-8, 1-23

 

 

powering up

2-17

 

 

 

power supply

1-9, 1-25

 

 

power supply LED descriptions

1-9, 1-25

rear view

 

1-3, 1-17

 

 

 

removing from a rack (procedure)

2-25

repacking for return

2-26

 

 

supported SFP transceivers

1-14, 1-28

system ground location (figure)

2-16

console port

 

 

 

 

 

 

connecting (figure)

3-2, 3-3

 

 

connecting (procedure) 3-3

 

 

pinouts

C-3

 

 

 

 

contact and site information

 

 

records

D-3

 

 

 

 

worksheet

D-3

 

 

 

D

dimensions

Cisco 5000 Series Hardware Installation Guide

 

OL-15902-01

IN-1

 

1-12, 1-27
2-6, 2-9
2-14
2-15
2-10
2-13
2-12

Index

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

chassis B-1

description

1-5

documentation

port grouping

1-6

additional publications i-xiv

port numbering (figure) 1-5, 1-8, 1-21

 

Fibre Channel ports

E

electrostatic discharge (ESD)

prevention guidelines

2-12

Ethernet connector port

 

connecting (procedure)

3-3

description 1-4, 1-19

 

Ethernet expansion module

description 1-6, 1-7, 1-21, 1-22

port numbering (figure)

1-9

Ethernet LEDs

 

 

 

description

1-5, 1-20

 

Ethernet ports

 

 

 

connecting

3-4

 

 

expansion modules

 

 

description

1-5

 

 

installing (procedure)

2-19

port numbering

1-5, 1-21

removing (procedure)

2-20

specifications

B-2

 

F

fan modules

 

 

description

1-10, 1-26

 

installing (procedure)

2-25

LED descriptions 1-11, 1-27

removing (procedure)

2-24

FCoE protocol

 

 

description

1-1, 1-16

 

fiber optic cables

 

 

maintaining

3-11

 

Fibre Channel over Ethernet protocol. See FCoE protocol Fibre Channel plus Ethernet expansion module

Cisco 5000 Series Hardware Installation Guide

connecting 3-7

G

grounding

attaching the ESD wrist strap (procedure)

attaching the ESD wrist strap to the system ground (figure)

best practices chassis

establishing the system ground 2-14

tools and equipment to connect the system ground

guides rack-mount

L

LC-typecables

connecting to Fibre Channel ports 3-10

LED descriptions

power supplies B-3 switch

N

network connections preparing 3-2

P

port numbering description 1-8, 1-23

power cords

jumper power cord (figure) C-10

IN-2

OL-15902-01

Index

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

length

C-4

 

 

 

supported power cords (figure)

C-5

supported power cords (table)

C-4

power plugs

 

 

 

 

supported power plugs (figure)

C-5

power supplies

 

 

 

blank filler panel (figure) 1-10, 1-26

description

1-9, 1-25

 

 

installing (procedure)

2-22

 

LED descriptions 1-10, 1-25, B-3

 

removing (procedure)

2-21

 

specifications B-2, B-3

 

 

pre-installation

 

 

 

guidelines

2-2

 

 

options

2-2

 

 

 

unpacking the switch

2-4

 

R

rack 2-5, 2-8

 

 

rack-mountinstallation

 

procedure

2-6, 2-9

 

rack-mountkit

 

 

contents

2-5, 2-8

 

records

 

 

chassis serial number D-4

 

contact and site information

D-3

site planning and maintenance

D-1

required equipment

 

switch installation 2-4

 

RJ-45connector

 

pinouts C-2

 

S

screw torques description 2-4

SFP+ transceivers

installing (procedure)

3-4

 

installing a cable (procedure)

3-6

maintaining

3-7

 

 

removing (procedure)

3-4

 

removing a cable (procedure)

3-6

specifications

B-4

 

 

SFP transceivers

 

 

 

description

3-7

 

 

installing (procedure)

3-7

 

installing a cable 3-6

 

 

removing (procedure)

3-8

 

removing a cable (procedure)

3-10

specifications

B-4

 

 

supported

1-14, 1-28

 

 

site planning

 

 

 

 

checklist

D-2

 

 

 

Small-Form-Factor Pluggable transceivers. See SFP transceivers

specifications

 

 

 

cables

C-1

 

 

 

environmental

B-1

 

expansion modules

B-2

physical

B-1, B-2

 

power supplies

B-2, B-3

transceivers

B-4

 

switch installation

 

 

equipment required

2-4

guidelines

2-3

 

 

screw torques

2-4

 

T

transceivers, supported SFPs. See SFP transceivers troubleshooting

best practices E-1

Cisco 5000 Series Hardware Installation Guide

 

OL-15902-01

IN-3

 

Index

Se n d d o c u m e n t a t i o n c o m m e n t s t o n ex u s 5 k d o c s @ c i s c o . c o m

Cisco 5000 Series Hardware Installation Guide

 

IN-4

OL-15902-01