Cisco Systems 400 User Manual

Size:
583.25 Kb
Download

Quick Start Guide

FA S THU B400 10/100 SE R I E S

CA B L I N G A N DST A R TUP

1

TAKEOUTWHATYOUNEED

2

CONNECT THEHUB TOOTHERNETWORKDEVICES

3

ASSIGNIP INFORMATION TO THEHUB

4

DISPLAY THEWEB-BASEDHUBMANAGER

Take Out What You Need

FastHub 400 10/100 series hub (12or 24-portmodel)

FastHub 400 10/100 Series Installation

and Configuration Guide

Quick

Installation

Guide Start

Configuration

Guide

 

RJ-45-to-RJ-45rollover console cable (FastHub 412M and FastHub 424M models only)

RJ-45-to-DB-9console-to-PCadapter1 (FastHub 412M and FastHub 424M

models only)

Black AC power cable

Rack-mountkit

Rubber feet

If any item is missing or damaged, contact your Cisco representative or reseller for support.

Note: You need to supply Category 3, 4, or 5 straight-throughor crossover cables to connect to Ethernet devices.

Connect the Hub to Other Network Devices

RPS

10

100

MODE

 

 

 

 

 

 

 

 

 

 

 

 

10BaseT/100BaseTx

 

 

 

 

 

 

 

 

 

 

 

 

1x

2x

3x

4x

5x

6x

7x

8x

9x

10x

11x

12x

13x

14x

15x

16x

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17x

18x

19x

20x

21x

22x

23x

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24x

24

10BaseT/100BaseTX network port (RJ-45)

Maximum cable length:

328 ft (100 m) 10BaseT or 100BaseTX port

(RJ-45)

Ethernet cable (not supplied)

Note: Use a straight-throughcable to connect two ports when one of the ports is designated with anX. Use a crossover cable to connect two ports when both ports are designated with anX.

Connect the Hub to Servers, Routers, and Workstations

Connect a Category 3, 4, or 5 straight-through cable to any 10/100 port on the hub and to a 10BaseT port on the workstation, server, or router.

Connect a Category 5 straight-through cable to any 10/100 port on the hub and to a 100BaseTX port on the workstation, server, or router.

2

Connect the Hub to Switches and Other Hubs

Connect a Category 3, 4, or 5 crossover cable to any 10/100 port on the hub and to a 10BaseT port on the target switch or hub.

Connect a Category 5 crossover cable to any 10/100 port on the hub and to a 100BaseTX port on the target switch or hub.

Connect the Hub to Other Network Devices (continued)

RATING

100-127

/ 200-240V~

2A /1A

50 / 60 Hz

UP CONSOLE

DOWN

DC INPUTS FOR REMOTE

 

POWER SUPPLY

SPECIFIED IN MANUAL

+5V

@6A, +12V

@1A

 

DC INPUT

 

10/100 BASE-TX

 

MEDIA MODULE

RATING

100-127

/ 200-240V~

2A /1A

50 / 60 Hz

UP CONSOLE

DOWN

DC INPUTS FOR REMOTE

 

POWER SUPPLY

SPECIFIED IN MANUAL

+5V

@6A, +12V

@1A

 

DC INPUT

 

10/100 BASE-TX

MEDIA MODULE

RATING

100-127

/ 200-240V~

2A /1A

50 / 60 Hz

UP CONSOLE

DOWN

DC INPUTS FOR REMOTE

 

POWER SUPPLY

SPECIFIED IN MANUAL

+5V

@6A, +12V

@1A

 

DC INPUT

 

100 BASE-FX

MEDIA MODULE

3(Optional) Install the Switched Uplink Module in the Hub

1Power off the hub.

2Remove and set aside the screws attaching the faceplate to expansion slot on the hub. The screws will be used later in Step 6.

3Remove the faceplate from the hub and store it for future use.

4Slide the module into the slot card-guidesuntil you feel it touch the back of the hub.

5Push the module firmly until it snaps into place and is firmly seated.

6Insert and tighten the screws on the module faceplate.

7Power on the hub.

(Optional) Connect to the Switched Uplink Module Port

Insert a connector according to the type of module (10/100 or 100BaseFX), as follows:

10BaseT/100BaseTX connector—Insertthe connector until it snaps into place in the module port.

Note: Use a straight-throughcable to connect two ports when one of the ports is designated with anX. Use a crossover cable to connect two ports when both ports are designated with anX.

100BaseFX SC connector—Removethe rubber plugs from thefiber-opticport on the module and store them for future use. Insert the connector in thefiber-opticmodule port.

Connect the Hub to Other Network Devices (continued)

RATING

100-127

/ 200-240V~

2A /1A

50 / 60 Hz

Power outlet

RJ-45-to-RJ-45rollover console cable (supplied)

 

DC INPUTS FOR REMOTE

UP

POWER SUPPLY

SPECIFIED IN MANUAL

CONSOLE

+5V @6A, +12V @1A

 

DC INPUT

DOWN

 

Console port (RJ-45)

10/100 BASE-TX

STAT DUP 100

MEDIA MODULE

(Optional) Connect the

Console Cable

1Make sure console port settings of the FastHub 400M model match the settings of the terminal, PC, or laptop. The default settings of the hub console port are 9600 baud, 8 data bits,

1 stop bit, no parity, and no flow control.

2Connect the rollover console cable to the CONSOLE port on the hub.

3Connect the other end of the rollover cable to your terminal, PC, or laptop (if necessary, use an appropriate adapter, such as the supplied RJ-45-to-DB-9adapter).

4From your terminal, PC, or laptop, start the terminal emulation program.

RJ-45-to-DB-9

 

adapter (supplied)

4

 

Power Up the Hub

1Connect one end of the power cord to the hub and the other end to a power source.

Note: You can use the internal power supply and the Cisco 600W AC Redundant Power System (RPS). Attach only the Cisco RPS (model PWR600-AC-RPS)to the RPS receptacle.

2Wait approximately 2 minutes for the hub to complete its power-onself-test(POST).

After POST completes, the Continue with configuration dialog? prompt appears on the management station. You can then follow the prompts to assign IP information to the hub.

(Optional) Assign IP Information to the Hub

 

The hub is designed to operate with little or

4

Enter the IP address of the default

 

no user intervention. In most cases, you can

 

gateway (for example: 10.1.105.254):

 

use it with its default settings.

Enter IP default gateway: 10.1.105.254

 

 

 

 

 

 

 

 

 

 

 

Assign IP information to the FastHub 400M

 

The following information is displayed:

 

model so that you can use the FastHub 400

 

 

 

 

 

series Hub Manager web-basedinterface

The following configuration command

 

and so that the hub can communicate with

script was created:

 

local routers and the intranet.

ip address 10.1.105.20 255.255.255.0

 

ip default-gateway10.1.105.254

 

 

 

 

 

 

 

 

 

 

 

Contact your system administrator for the

!

 

 

end

 

 

hub IP information, and record it here.

 

 

 

 

 

Hub IP address:

 

 

 

 

 

 

 

5

Enter Y:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use this configuration? Y

 

Subnet mask:

 

 

 

 

 

 

 

 

The following information is displayed:

 

 

 

 

 

 

 

Default gateway:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Building configuration...

 

1

From the terminal or PC, enter Y:

5

Use the enabled mode ‘configuration’

 

 

 

 

 

 

 

 

 

Continue with configuration dialog? Y

command to modify this configuration.

 

 

 

 

2

Enter the IP address (for example:

Press RETURN to get started.

 

 

 

 

 

10.1.105.20):

 

 

 

 

 

 

 

6

Press Return.

 

 

 

 

 

 

 

 

 

 

 

Enter IP address: 10.1.105.20

7

Exit from the terminal session.

 

 

 

 

 

 

 

 

 

 

 

3

Enter the subnet mask (IP netmask)

You can now display the FastHub 400 series

 

Hub Manager.

 

 

(for example: 255.255.255.0):

 

Enter IP netmask: 255.255.255.0

 

 

(Optional) Display the FastHub 400 Series

Hub Manager

If you have the IP address to the hub, you can display the FastHub 400 series Hub Manager from your intranet. You can use the FastHub 400 series Hub Manager to configure and monitor the hub.

1Start Netscape Communicator (4.03 or higher) or Microsoft Internet Explorer (4.01 or higher). Make sure that Java and JavaScript are enabled.

2Enter the IP address of the hub in the URL field if you are using Communicator (the Address field if you are using Internet Explorer).

The FastHub 400 series Hub Manager Home page appears.

Click Apply after

 

 

HOME PORT GROUP IP SNMP CDP SYSTEM

 

 

Click these topics to move from page

 

 

 

 

 

 

 

 

 

 

to page. On Netscape Communicator

 

making changes

 

 

 

 

 

 

 

 

 

 

 

only, when the cursor is above a topic,

 

on a page.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a pop-upbriefly describes the options

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on that particular page.

 

Click Revert

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to discard

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

unapplied

 

 

 

 

 

 

 

 

 

 

 

 

 

 

changes on

 

 

 

 

 

 

 

 

 

Click a port to display its

6

a page.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

settings, status, and statistics.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Click Help for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

procedures and

 

 

 

 

 

 

 

 

 

 

 

 

detailed field

 

 

 

 

 

 

 

 

 

 

 

 

descriptions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Click the Mode

 

 

 

 

 

Click to display the settings, status, and

 

 

 

 

 

 

 

statistics of an installed 10BaseT/100BaseTX

 

 

button to change

 

 

 

 

 

the mode that

 

 

 

or 100BaseFX switched uplink module.

 

 

the LEDs display

 

 

 

 

 

 

 

 

 

 

 

 

for the fixed

 

 

 

 

 

 

 

 

 

 

 

 

10/100 ports.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Shows when another hub is connected to a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

stacking connector on the hub rear panel.

 

Note: The FastHub 400 10/100 Series Installation and Configuration Guide and the FastHub 400 10/100 series Hub Manager online help provide complete information about the web console and describe how to configure and monitor the hub.

Corporate Headquarters

 

 

 

 

 

 

 

 

European Headquarters

Americas

Asia Headquarters

Cisco Systems, Inc.

Cisco Systems Europe s.a.r.l.

Headquarters

Nihon Cisco Systems K.K.

170 West Tasman Drive

Parc Evolic, Batiment L1/L2

Cisco Systems, Inc.

Fuji Building, 9th Floor

San Jose, CA 95134-1706

16 Avenue du Quebec

170 West Tasman Drive

3-2-3Marunouchi

USA

 

Villebon, BP 706

San Jose, CA 95134-1706

Chiyoda-ku,Tokyo 100

http://www.cisco.com

91961 Courtaboeuf Cedex

USA

 

Japan

 

Tel:

408 526-4000

France

http://www.cisco.com

http://www.cisco.com

 

800 553-NETS(6387)

http://www-europe.cisco.com

Tel:

408 526-7660

Tel:

81 3 5219 6250

Fax:

408 526-4100

Tel:

33 1 6918 61 00

 

Fax:

408 527-0883

Fax:

81 3 5219 6001

 

 

Fax:

33 1 6928 83 26

 

 

 

 

 

 

Cisco Systems has more than 200 offices in the following countries. Addresses, phone numbers, and fax numbers are listed on the

C i s c o C o n n e c t i o n O n l i n e W e b s i t e a t h t t p : / / w w w . c i s c o . c o m .

Argentina AustraliaAustriaBelgiumBrazilCanadaChileChina (PRC)ColombiaCosta RicaCzech RepublicDenmark EnglandFranceGermanyGreeceHungaryIndiaIndonesiaIrelandIsraelItalyJapanKoreaLuxembourgMalaysia MexicoThe NetherlandsNew ZealandNorwayPeruPhilippinesPolandPortugalRussiaSaudi ArabiaScotlandSingapore South AfricaSpainSwedenSwitzerlandTaiwan, ROCThailandTurkeyUnited Arab EmiratesUnited StatesVenezuela

AccessPath, Any to Any, AtmDirector, the CCIE logo, CD-PAC,Centri, the Cisco Capital logo,CiscoLink, the Cisco Management Connection logo, the Cisco NetWorks logo, the Cisco Powered Network logo, the Cisco Press logo, the Cisco Technologies logo, ClickStart, ControlStream, DAGAZ, Fast Step, FireRunner, IGX, IOS, JumpStart, Kernel Proxy, LoopRunner, MGX, Natural Network Viewer, NetRanger, NetRanger Director, NetRanger Sensor, NetSonar,Packet, PIX, Point and Click Internetworking, Policy Builder, Precept, RouteStream, Secure Script, SMARTnet, SpeedRunner, Stratm, StreamView,The Cell, TrafficDirector, TransPath, ViewRunner, VirtualStream, VlanDirector, Workgroup Director, and Workgroup Stack are trademarks; Changing the Way We Work, Live, Play, and Learn, Empowering the Internet Generation, The Internet Economy, and The New Internet Economy are service marks; and BPX, Catalyst, Cisco, Cisco IOS, the Cisco IOS logo, Cisco Systems, the Cisco Systems logo, Enterprise/Solver, EtherChannel, FastHub, ForeSight, FragmentFree, IP/TV, IPX, LightStream, LightSwitch, MICA, Phase/IP, StrataSphere, StrataView Plus, and SwitchProbe are registered trademarks of Cisco Systems, Inc. in the U.S. and certain other countries. All other trademarks mentioned in this document are the property of their respective owners. (9811R)

78-5566-01