Cisco Systems 2800 Series User Manual

Size:
329.69 Kb
Download

Cisco 800 Series Router Cabling and Setup

Quick Start Guide

This document describes the basic process of cabling and configuring the Internet access device, the Cisco 800 series router. For advanced cabling information, refer to the Cisco 800 Series Router Hardware Installation Guide. For advanced configuration information, refer to theCisco 800 Series Router Software Configuration Guide . These documents are available on the Cisco DocumentationCD-ROMand on the World Wide Web.

You can access the most current Cisco documentation on the World Wide Web at the following sites:

http://www.cisco.com

http://www-china.cisco.com

http://www-europe.cisco.com

Parts List

The shipment of your Cisco 800 series router includes the following items:

One Cisco 800 series router

One yellow Ethernet cable

One orange ISDN S/T cable (Cisco 801 and Cisco 803 only)

One red ISDN U cable (Cisco 802 and Cisco 804 only)

One RJ-45-to-RJ-11adapter cable (for use with the red ISDN U cable)

One blue console cable

One DB-9-to-RJ-45adapter (for use with the blue console cable)

One DB-25-to-RJ-45adapter (for use with the blue console cable)

One black power supply

One black power supply cord

800 and SOHO Series Product Documentation CD

Cisco 800 Fast Step CD-ROM

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706USA

Copyright © 2001. Cisco Systems, Inc. All rights reserved.

Verify the PC Setup

Figure 1 shows the items included with the router. If any of the items is missing or damaged, contact your customer service representative.

Figure 1 Items Included with the Router

Yellow Ethernet cable

DocumentationCD-

ROM

DocumentaionOther

Quick

GuideStart

Orange ISDN S/T cable

(Cisco 801 and Cisco 803)

Product documentation

Cisco

800

Fast

 

 

Step

Red ISDN U cable

(Cisco 802 and Cisco 804)

Cisco 800

Fast Step CD-ROM

RJ-45-to-RJ-11adapter cable

Light blue console cable

 

(for use with red ISDN U cable)

 

 

DB-9-to-RJ-45adapter

Desktop power supply

(for use with light blue console cable)

 

DB-25-to-RJ-45adapter

Black power cord

(for use with light blue console cable)

Verify the PC Setup

Before you begin, verify that each computer that will be connected to the router has a network interface card (NIC) installed and that Transmission Control Protocol/Internet Protocol (TCP/IP) has been loaded and configured. For more information on how to configure TCP/IP, refer to the PC Configuration Instructions to Establish Cisco Router-to-PC Communications, which is available on the Cisco DocumentationCD-ROM,and refer to information available the Microsoft web site.

Verify the PC Setup

2

78-5374-03

 

 

Connect the Cisco 800 Series Router to a PC

Connect the Cisco 800 Series Router to a PC

Follow these steps to connect the Cisco 800 series router to a PC:

Step 1 Connect the yellow Ethernet cable from the yellow Ethernet port (Cisco 801 and 802 routers) or from the yellow Ethernet port with the number 0 (Cisco 803 and 804 routers) on the back panel of the router to the Ethernet port on the NIC on the computer.

Figure 2 Connecting a Cisco 800 Series Router to a PC

HUB

NO HUB

ETHERNET 10

BASE T

 

0

 

1

2

 

Cisco

 

803

CONSOLE

ISDN S/T

 

 

PHONE

3

 

 

1

 

2

Cisco 803 router

PC

AUX

0

OK

LAN

SER

 

 

AUX

 

 

Step 2 Verify that the HUB/NO HUB switch on the left side of the back panel has been set to the NO HUB position (out). If the button is in, press it to set it to the out position.

Note The HUB/NO HUB button corresponds to the Ethernet port on Cisco 801 and 802 routers and to Ethernet port 0 on Cisco 803 and 804 routers.

Step 3 For Cisco 803 and 804 routers, connect additional computers to the Cisco 800 series router by connecting Ethernet cables from the Ethernet ports labeled with the numbers 1, 2, and 3 to the Ethernet ports on the computers.

Caution Always connect the yellow cable or Ethernet cable that you supply to the yellow ports on the router. Do not connect the cable to an ISDN S/T or U port or to a Network Termination 1 (NT1) device. Accidently connecting the cable to the wrong port can damage your router.

Connect the Cisco 800 Series Router to a PC

 

78-5374-03

3

 

 

 

Connect the Cisco 800 Series Router to a Hub

Connect the Cisco 800 Series Router to a Hub

Follow these steps to connect the Cisco 800 series router to a hub:

Step 1 Connect the yellow Ethernet cable from the yellow Ethernet port (Cisco 801 and 802 routers) or from the yellow Ethernet port with the number 0 (Cisco 803 and 804 routers) on the back panel of the router to the Ethernet port on the hub.

Figure 3 Connecting a Cisco 800 Series Router to a Hub

HUB

NO HUB

ETHERNET 10

BASE T

 

0

 

1

2

 

Cisco

 

803

CONSOLE

ISDN S/T

 

 

PHONE

3

 

 

1

 

2

SPEED

LED

100BaseTX

SOLID

10BaseT

BLINK

1X

 

 

2X

10/100

 

 

3X

 

 

4X

1

2

3

4

5

6

7

8

 

 

 

 

 

5X

 

 

 

6X

 

 

 

7X

 

 

 

8X

MDI

MDI-X

Cisco 1528 Micro Hub 10/100

Step 2 Verify that the HUB/NO HUB switch on the left side of the back panel has been set to the HUB position (in). If the button is out, press it to set it to the in position.

Note The HUB/NO HUB button corresponds to the Ethernet port on Cisco 801 and 802 routers and to Ethernet port 0 on Cisco 803 and 804 routers.

Caution Always connect the yellow cable or Ethernet cable that you supply to the yellow ports on the router. Do not connect the cable to an ISDN S/T or U port or to a Network Termination 1 (NT1) device. Accidently connecting the cable to the wrong port can damage your router.

Connect the Cisco 800 Series Router to a Hub

4

78-5374-03

 

 

Connect an ISDN Line

Connect an ISDN Line

Refer to the section corresponding to your router model and follow the steps to connect the

Cisco 800 series router to an ISDN line.

Option A—ConnectingCisco 801 and Cisco 803 Routers

Option B—ConnectingCisco 802 and Cisco 804 Routers

Caution Always connect the orange cable to the orange ISDN S/T port and the red cable to the red ISDN U port on the router. Do not connect either cable to the yellow Ethernet port. Accidently connecting these cables to the wrong port can damage your router.

Option A—ConnectingCisco 801 and Cisco 803 Routers

This section describes how to connect Cisco 801 and Cisco 803 routers outside of North America. For information on connecting these routers in North America, see the Cisco 800 Series Routers Hardware Installation Guide.

Figure 4 Connecting an 801 or 803 Router to an ISDN Line

HUB

NO HUB

ETHERNET 10

BASE T

 

0

Cisco

 

803

CONSOLE

ISDN S/T

 

ISDN wall jack

Step 1 Connect the orange cable to the orange ISDN S/T port.

Step 2 Connect the other end of the cable to the ISDN wall jack.

Connect an ISDN Line

 

78-5374-03

5

 

 

 

Connect Telephone, Fax Machine, or Modem

Option B—ConnectingCisco 802 and Cisco 804 Routers

Figure 5 Connecting an 802 or 804 Router to an ISDN Line

HUB

 

 

 

NO HUB

 

Cisco

 

ETHERNET 10

BASE T

804

 

 

 

 

 

CONSOLE

 

0

 

 

ISDN U

1

2

 

PHONE

 

3

 

 

 

 

Cisco 804 router

 

1

 

 

 

2

ISDN wall jack

RJ-45-to-RJ-11adapter cable

Step 1 Connect the red cable to the red ISDN U port.

Step 2 Connect the other end of the cable to the ISDN wall jack. If your wall jack has anRJ-11connector, attach theRJ-45-to-RJ-11adapter cable to the red cable, and then connect theRJ-11connector to the ISDN wall jack.

Connect Telephone, Fax Machine, or Modem

If you have a Cisco 803 or Cisco 804 router, you can connect a touch-tonetelephone, fax machine, or modem. Use the cables provided with these devices.

The gray PHONE 1 and PHONE 2 ports are RJ-11connectors. If you are outside of North America, you must buy and attach adapters that allow your telephones, faxes, or modems to be connected to theseRJ-11connectors. In some countries, these adapters need additional electronics to convert the telephones, faxes, or modems to work properly with the router phone ports. For example, in the United Kingdom, you must buy an adapter that also provides amaster socket, which causes incoming calls to ring the connected devices. For information on recommended master sockets, see theCisco 800 Series Routers Hardware Installation Guide.

Caution Do not connect the router telephone ports to the telephone wall jack. These ports are not meant for direct connection to the public network. This connection can damage your router.

Option B—ConnectingCisco 802 and Cisco 804 Routers

6

78-5374-03

 

 

Connect the Power and Turn On the Router

Figure 6 Connecting an 800 Series Router to a Telephone

HUB

 

 

 

 

NO HUB

 

Cisco

 

 

ETHERNET 10

BASE T

804

 

 

 

 

 

 

 

CONSOLE

 

 

0

 

 

ISDN U

 

1

2

 

 

PHONE

 

3

 

 

 

 

 

 

Cisco 804 router

 

1

2

Analog

Step 1 Connect one end of the telephone cable to the gray PHONE 1 or PHONE 2 port. If you are connecting only one device, use the PHONE 1 port.

Step 2 Connect the other end of the cable to your device.

Connect the Power and Turn On the Router

Follow these steps to connect power to the Cisco 800 series router and turn it on:

Figure 7 Connecting the Power to an 800 Series Router

HUB

NO HUB

ETHERNET 10

BASE T

0

 

1

2

 

Cisco

 

803

CONSOLE

ISDN S/T

 

 

PHONE

3

 

 

1

To electrical outlet

Desktop power supply

Connect the Power and Turn On the Router

 

78-5374-03

7

 

 

 

Verifying the LEDs

Step 1 Make sure the router power is off. Press the power switch to standby ().

Step 2 Connect the power supply cable to the8-pinconnector on the router.

Step 3 Connect the power cord to the desktop power supply.

Step 4 Connect the other end of the power cord to an electrical outlet.

Step 5 Turn ON the router. Press the power switch to on (|).

Verifying the LEDs

Verify the power connection and all other connections (links) by checking the LEDs in the table below. If the LEDs are not on, see the troubleshooting information in the Cisco 800 Series Routers Hardware Installation Guide.

Power/Link

LEDs To Check

Normal Patterns

Power

OK

On

 

 

 

To hub, server, PC, or workstation

Cisco 801 or Cisco 802 back panel: On LINK LED

Cisco 803 or Cisco 804 front panel: LKØ, LK1, LK2, and LK3 LEDs

To ISDN network using

LINE, CH1, or CH2

On. CH1 or CH2 is on only

ISDN S/T port

 

when the router has an active

 

 

voice or data connection.

 

 

 

To ISDN network using

NT1, LINE, CH1, or CH2

On. CH1 or CH2 is on only

ISDN U port

 

when the router has an active

 

 

voice or data connection.

 

 

 

To telephone, fax, or

PH1 or PH2

On. PH1 or PH2 is on only

modem

You can also pick up the handset and

when telephone, fax, or

 

modem is in use.

 

listen for a dial tone.

 

 

 

 

 

Verifying the LEDs

8

78-5374-03

 

 

About the Product CD

About the Product CD

The 800 and SOHO Series Product Documentation CD contains the technical publications for the 800 and SOHO series routers.

System Requirements

Processor

Pentium 150 MHz or faster recommended

 

 

PC OS

Microsoft Windows 95

 

Microsoft Windows 98

 

Microsoft Windows 2000

 

Microsoft Windows NT 4.0

 

 

Memory

64-MBDRAM

 

 

Drives

4x CD-ROMdrive

 

 

Monitor

Color monitor capable of 800 x 600 pixel

 

resolution

 

 

Software

Netscape 3.0 or later

 

Internet Explorer 3.0 or later

 

Adobe Acrobat Reader 3.0 or later

 

 

Documentation Exceptions

This CD does not contain certain publications that were incomplete or unavailable when this CD was produced. These documents are in the 800 and SOHO platform hardware accessory kits and should be consulted before installing and configuring your system. You can also access these documents on the Documentation page on Cisco Connection Online (CCO) at www.cisco.com.

Cisco 800 Series Routers Release Notes

Cisco 828 and SOHO 78 Routers Release Notes

IOS Release Notes for the Cisco 800 Series Router

IOS Release Notes for the Cisco 828 Router

Cisco Router Web Setup User Guide

About the Product CD

 

78-5374-03

9

 

 

 

About the Product CD

Using the CD Interface

When the CD is first launched, it automatically opens a browser session and displays the CD interface in the browser window. You can use the list of books in the left pane of your display to navigate directly to the book you want to view. Within the interface, you can use your mouse to:

Hover over book titles in the left column for an overview of the document before opening a document.

Select a book title from the document list on the left or from the document drop-downmenu on the CD title bar.

Click the Cisco Systems corporate icon to display Cisco support and service information.

Click About This CD (notepad icon) to get additional information about this CD.

Click Send Us Your Feedback! (pencil & notepad icon) to provide us with your feedback.

Click Get Acrobat Reader to install a free copy of Adobe Acrobat Reader 4.0.

Changing the Display Properties of Documents

When you first launch the CD, you will notice a list of books in the left pane of your display that you can use to navigate directly to the book you want to view. When you select the document, Acrobat Reader opens the book in .pdf format and provides a list of topics in the left frame of the Acrobat window. To disable this option and view the book fully in the window, click the Show/Hide Navigation Pane button on the Acrobat toolbar. Note that when hiding bookmarks, the thumbnails, annotations, and articles are also hidden.

Printing Documents

To print a document:

Step 1 Click thePrinter icon on the Acrobat toolbar.

The Windows Print Dialog box appears.

Step 2 Select your default printer and clickOK.

Ordering Printed Copies of Documents

You can order printed copies of the documents on this CD and additional copies of this CD on the 800 and SOHO platform product ordering pages on Cisco Connection Online (CCO). Registered CCO users can order documentation for other Cisco products and the Cisco Documentation CD-ROM(containing all Cisco documentation) through our online Subscription Services athttp://www.cisco.com/cgi-bin/subcat/kaojump.cgi.

Nonregistered CCO users can order documentation through a local account representative by calling Cisco’s corporate headquarters (California, USA) at 408 526-4000or, in North America, by calling 800553-NETS(6387).

You can access the most current Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com,orhttp://www-europe.cisco.com.

Using the CD Interface

10

78-5374-03