Cisco Systems 2600XM User Manual

Size:
3.13 Mb
Download

Quick Start Guide

Cisco 2600XM Series and Cisco 2612 Routers

INCLUDING LICENSE AND WARRANTY

1Cisco 90-Day Limited Hardware Warranty Terms

2Documents, Equipment, and Tools

3Install Chassis

4Connect Cables

5Power Up the Router

6Perform Initial Configuration

7Interface Numbering

8Where to Go Next

9Obtaining Documentation

10Documentation Feedback

11Obtaining Technical Assistance

12Obtaining Additional Publications and Information

1 Cisco90-DayLimited Hardware Warranty Terms

There are special terms applicable to your hardware warranty and various services that you can use during the warranty period. Your formal Warranty Statement, including the warranties and license agreements applicable to Cisco software, is available on Cisco.com. Follow these steps to access and download the Cisco Information Packet and your warranty and license agreements from Cisco.com.

1.Launch your browser, and go to this URL: http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htm The Warranties and License Agreements page appears.

2.To read the Cisco Information Packet, follow these steps:

a.Click the Information Packet Number field, and make sure that the part number78-5235-03A0is highlighted.

b.Select the language in which you would like to read the document.

c.Click Go. The Cisco Limited Warranty and Software License page from the Information Packet appears.

d.Read the document online, or click the PDF icon to download and print the document in Adobe Portable Document Format (PDF).

Note You must have Adobe Acrobat Reader to view and print PDF files. You can download the reader from Adobe’s website:http://www.adobe.com

3.To read translated and localized warranty information about your product, follow these steps:

a.Enter this part number in the Warranty Document Number field: 78-5236-01C0

b.Select the language in which you would like to read the document.

c.Click Go. The Cisco warranty page appears.

d.Review the document online, or click the PDF icon to download and print the document in Adobe Portable Document Format (PDF).

You can also contact the Cisco service and support website for assistance:

http://www.cisco.com/en/US/support/

Duration of Hardware Warranty

Ninety (90) days.

Replacement, Repair, or Refund Policy for Hardware

Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten (10) working days after receipt of a Return Materials Authorization (RMA) request. Actual delivery times can vary, depending on the customer location.

Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.

To Receive a Return Materials Authorization (RMA) Number

Contact the company from whom you purchased the product. If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representative.

Complete the information below, and keep it for reference:

Company product purchased from

Company telephone number

Product model number

Product serial number

Maintenance contract number

2

2 Documents, Equipment, and Tools

User Documentation

All the documents referenced in this quick start guide are available online on Cisco.com. To be sure of obtaining the latest information, you should access the online documentation.

To view or print a document in its original page format, access the online document, and click the PDF icon.

For information about accessing user documentation, see the “Where to Go Next” section on page 24.

Items Included with Cisco 2600XM Series Routers

Rack-mountbrackets with screws for19-inchrack; rubber chassis feet

Ground lug; power cord

RJ-45-to-DB-9adapter cable for console connection

RJ-45-to-DB-25adapter cable for modem connection

Ethernet cable for LAN interface

Cisco Information Packet

Cisco 90-DayLimited Hardware Warranty Terms

Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Regulatory Compliance and Safety Information document

Cisco Router and Security Device Manager (SDM) Quick Start Guide document (if shipped with VPN bundle)

Cisco 2600XM Series and Cisco 2612 Routers Quick Start Guide (this document)

Items Not Included

Individual items in this list may be required for your particular application:

Four screws for installing the chassis in a rack

PC running terminal emulation software for administrative access, or modem for remote administrative access

Cables for WAN interfaces, voice interfaces, or additional LAN interfaces

Cable ties

Number 2 Phillips screwdriver

3 Install Chassis

Safety Information

For safety information you need to know before working on your Cisco router, refer to the Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Regulatory Compliance and Safety Information document that accompanied this device.

Note To see translations of the warnings that appear in this publication, refer to theCisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Regulatory Compliance and Safety Information document.

3

Warning Definition

IMPORTANT SAFETY INSTRUCTIONS

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Voor een vertaling van de waarschuwingen die in deze publicatie verschijnen, dient u de vertaalde veiligheidswaarschuwingen te raadplegen die bij dit apparaat worden geleverd.

Opmerking BEWAAR DEZE INSTRUCTIES.

Varoitus TÄRKEITÄ TURVALLISUUTEEN LIITTYVIÄ OHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä asiakirjassa esitettyjen varoitusten käännökset löydät laitteen mukana toimitetuista ohjeista.

Huomautus SÄILYTÄ NÄMÄ OHJEET

Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vousavec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions d'avertissements figurant dans cette publication, consultez les consignes de sécurité traduites qui accompagnent cet appareil.

Remarque CONSERVEZ CES INFORMATIONS

Warnung WICHTIGE SICHERHEITSANWEISUNGEN

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewusst. Übersetzungen der in dieser Veröffentlichung enthaltenen Warnhinweise sind im Lieferumfang des Geräts enthalten.

Hinweis BEWAHREN SIE DIESE SICHERHEITSANWEISUNGEN AUF

4

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Per le traduzioni delle avvertenze riportate in questo documento, vedere le avvertenze di sicurezza che accompagnano questo dispositivo.

Nota CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette varselssymbolet betyr fare. Du befinner deg i en situasjon som kan forårsake personskade. Før du utfører arbeid med utstyret, bør du være oppmerksom på farene som er forbundet med elektriske kretssystemer, og du bør være kjent med vanlig praksis for å unngå ulykker. For å se oversettelser av advarslene i denne publikasjonen, se de oversatte sikkerhetsvarslene som følger med denne enheten.

Merk TA VARE PÅ DISSE INSTRUKSJONENE

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. O utilizador encontra-senuma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha em atenção os perigos envolvidos no manuseamento de circuitos eléctricos efamiliarize-secom as práticas habituais de prevenção de acidentes. Para ver traduções dos avisos incluídos nesta publicação, consulte os avisos de segurança traduzidos que acompanham este dispositivo.

Nota GUARDE ESTAS INSTRUÇÕES

¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Vea las traducciones de las advertencias que acompañan a este dispositivo.

Nota GUARDE ESTAS INSTRUCCIONES

Varning! VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Se översättningarna av de varningsmeddelanden som finns i denna publikation, och se de översatta säkerhetsvarningarna som medföljer denna anordning.

OBS! SPARA DESSA ANVISNINGAR

5

Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-secom as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

6

Advarsel VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be accessed only

 

 

through the use of a special tool, lock and key, or other means of security. Statement 1017

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and

 

 

watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld

 

 

the metal object to the terminals. Statement 43

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning

This equipment has been designed for connection to TN and IT power systems. Statement 1007

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

Warning

Warning

Warning

Warning

Warning

Warning

To avoid electric shock, do not connect safety extra-lowvoltage (SELV) circuits totelephone-networkvoltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both useRJ-45connectors. Use caution when connecting cables.Statement 1021

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Statement 1032

Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Installing the Chassis

You can set the chassis on a desktop or install it in a rack. A chassis of 1 RU height can also be mounted on a wall or other flat surface. See the applicable instructions in the following sections:

Rack-Mounting the Chassis, page 9

Wall-Mounting the Chassis—1-Rack-Unit (RU) Chassis Height Only, page 12

Installing on a Desktop, page 13

Caution To prevent damage to the chassis, never attempt to lift or tilt the chassis by the plastic panel on the front. Always hold the chassis by the metal body.

Rack-Mountingthe Chassis

Cisco 2600XM series and Cisco 2612 routers can be installed in 19-,23-,and24-inchracks. Use the standard brackets for mounting the chassis in a19-inchrack; use the optional larger brackets for mounting the chassis in a 23or24-inchrack.

You can mount the chassis in the following ways:

Center mounting—Bracketsattached in the center of the chassis with either the front panel or the rear panel facing forward

Front mounting—Bracketsattached at the front of the chassis with the front panel facing forward

Rear mounting—Bracketsattached at the rear of the chassis with the rear panel facing forward

9

The brackets for 19-,23-,and24-inchracks are shown inFigure 1.

Figure 1 Brackets for Rack-Mountingof Routers with1-RUChassis Height

Bracket for use with a 19-inchrack

Bracket for use with a 23-inchor24-inchrack

27711

Attaching Brackets

Attach the mounting brackets to the chassis as shown in Figure 2 throughFigure 8, using the screws provided. Attach the second bracket to the opposite side of the chassis. Use a number 2 Phillips screwdriver to install the bracket screws.

Figure 2 Bracket Installation for Front Mounting in 19-InchRack

Note: The second bracket attaches to the other side of the chassis

Figure 3 Bracket Installation for Front Mounting: 19-InchRack with17.75-InchOpening, and 23or24-InchRack

Note: The second bracket attaches

to the other side of the chassis. Brackets for 19-inchrack

Brackets for 23-inchor24-inchrack

62881

10

Figure 4 Bracket Installation for Rear Mounting in 19-InchRack

110V 60 Hz 1.6A MAX

Note: The second bracket attaches to the other side of the chassis.

Brackets for 19-inchrack

72013

Figure 5 Bracket Installation for Rear Mounting: 19-InchRack with17.75-InchOpening, and 23or24-InchRack

110V 60 Hz 1.6A MAX

Note: The second bracket attaches to the other side of the chassis.

Brackets for 19-inchrack

Brackets for 23-inchor24-inchrack

72014

Figure 6 Bracket Installation for Center Mounting with Rear Panel Forward: 19-InchRack with17.75-InchOpening, and 23or24-InchRack

110V 60 Hz 1.6A MAX

Note: The second bracket attaches to the other side of the chassis.

Brackets for 19-inchrack

Brackets for 23-inchor24-inchrack

72015

11

Figure 7 Bracket Installation for Center Mounting with Rear Panel Forward: 19-,23-,or24-InchRack

110V 60 Hz 1.6A MAX

Note: The second bracket attaches

Brackets for

to the other side of the chassis.

19-inchrack

Brackets for 23-inchor24-inchrack

62983

Figure 8 Bracket Installation for Center Mounting with Front Panel Forward: 19-,23-,or24-InchRack

Note: The second bracket attaches

Brackets for

to the other side of the chassis.

19-inchrack

Brackets for 23-inchor24-inchrack

72016

Installing Chassis in Rack

Install the chassis in the rack. Rack-mountingscrews are not provided with the router. Use two screws for each side (supplied with the rack).

Wall-MountingtheChassis—1-Rack-Unit(RU) Chassis Height Only

Cisco 2600XM series and Cisco 2612 routers can be attached to walls.

Attaching Rubber Feet

If you are mounting a Cisco 2600XM series or Cisco 2612 router on a wall, you must install the rubber feet that are supplied in the accessory kit. They provide a space for air circulation. Peel the rubber feet from the adhesive strip, and attach them onto the five round recesses on the bottom of the chassis.

Attaching Brackets

Attach the standard brackets to the chassis as shown in Figure 9, using the slottedhex-headscrews and plastic spacers (supplied in the accessory kit). Orient each spacer so that the shoulder fits into the slot in the bracket.

12

Figure 9 Attaching the Brackets for Wall-Mounting

SERIAL

 

 

A/S

 

 

3

CN/LP RXC

RXD TXC TXD

 

2

CN/LP

RXC

RXD TXC TXD

 

 

1

CN/LP RXC

RXD

TXC

 

 

W1

CONN

SERIAL

 

 

 

 

 

 

 

TXD

CN/LP RXC

 

 

 

 

 

 

 

 

 

0

RXD TXC TXD

 

 

 

 

 

 

 

 

 

 

 

 

 

CONN

 

 

 

 

 

 

 

EN

 

W0

SERIAL

 

 

 

 

 

 

 

 

 

W0

 

 

 

 

 

 

 

 

LINK

TOKEN RING

 

 

W0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0/0 ACT

LINK

 

 

 

 

 

 

 

 

 

 

 

ETHERNET

 

 

 

 

 

 

 

 

 

 

 

0/0 ACT

CONSOLE

 

 

 

 

 

 

 

 

 

 

 

AUX

Input:

100-240VAC

Freq:

 

50/60

Hz

Current: 1.2-

0.6A

Watts:

40W

Attaching to Wall

Attach the chassis to the wall:

Position the end nearest the power cable at the top.

Align screws (not included) with a wall stud, or use wall anchors.

88837

Installing on a Desktop

If you are installing a Cisco 2610XM, Cisco 2620XM, or Cisco 2650XM series router on a desktop, you must install the rubber feet that are supplied in the accessory kit. They provide a space for air circulation. Peel the rubber feet from the adhesive strip, and attach them onto the five round recesses on the bottom of the chassis.

Caution If you place the Cisco router on a desktop, do not place anything that weighs more than 10 pounds (4.5 kilograms) on top of the chassis.

Grounding the Chassis

You must connect the chassis to a reliable earth ground; the ground wire must be installed in accordance with local electrical safety standards.

For NEBS-compliantgrounding, use size AWG 6 (13 mm2) wire and the ground lug provided in the accessory kit.

For NEC-compliantgrounding, use size AWG 14 (2 mm2) or larger wire and an appropriateuser-suppliedring terminal.

For EN/IEC 60950-compliantgrounding, use size AWG 18 (1 mm2) or larger wire and an appropriateuser-suppliedring terminal.

To connect the chassis to a reliable earth ground, perform the following steps:

Step 1 Strip one end of the ground wire to the length required for the ground lug or terminal.

For the NEBS ground lug—approximately0.75 in. (20 mm)

For user-providedringterminal—asrequired

Step 2 Crimp the ground wire to the ground lug or ring terminal, using a crimp tool of the appropriate size.

13

Step 3 Attach the ground lug or ring terminal to the chassis as shown inFigure 10 orFigure 11. For the ground lug, use the two screws with captive locking washers provided. For a ring terminal, use one of the screws provided. Use a number 2 Phillips screwdriver, and tighten the screws to a torque of 8 to 10in-lb(0.9 to 1.1N-m).

Figure 10 NEBS-CompliantChassis Ground Connection Using Ground Lug

 

SERIAL 1

 

 

 

Cisco 2611

 

SERIAL 0

 

 

SERIAL 1

CONN

WIC

 

 

SERIAL 0

 

 

CONN 2A/S

CONN

 

CONN

WIC

W1

SEE MANUAL BEFORE INSTALLATION

 

SEE MANUAL BEFORE

2T

 

 

INSTALLATION

 

 

 

 

W0

 

 

 

 

 

LINK ETHERNET 1

ACT

LINK

ETHERNET 0

ACT CONSOLE

AUX

 

 

 

Ground lug

100-240V–1A 50/60 Hz 47 W

36454

Figure 11 Chassis Ground Connection Using Ring Terminal

 

SERIAL 1

 

 

 

Cisco 2611

 

SERIAL 0

 

 

SERIAL 1

CONN

WIC

 

 

SERIAL 0

 

 

CONN 2A/S

CONN

 

CONN

WIC

W1

SEE MANUAL BEFORE INSTALLATION

 

SEE MANUAL BEFORE

2T

 

 

INSTALLATION

 

 

 

 

W0

 

 

 

 

 

LINK ETHERNET 1

ACT

LINK

ETHERNET 0

ACT CONSOLE

AUX

 

 

 

Ring terminal

100-240V–1A 50/60 Hz 47 W

Step 4 Connect the other end of the ground wire to a grounding point at your site.

4 Connect Cables

Warning

Do not work on the system, or connect or disconnect cables during periods of lightning activity. Statement 1001

 

 

 

Warning

Before opening the chassis, disconnect the telephone-networkcables to avoid contact withtelephone-network

 

 

voltages. Statement 1004

 

 

 

System Management Connections

The connections described in Table 1 provide system management access.

Table 1

System Management Connections

 

 

 

 

 

 

Port

 

Color

Connected To:

Cable

 

 

 

 

 

Console

 

Light blue

PC or ASCII terminal communication port (usually labeled COM)

RJ-45-to-DB-9adapter cable

 

 

 

 

 

Auxiliary

 

Black

Modem for remote access

RJ-45-to-DB-25adapter cable

 

 

 

 

 

14

Power Connections

Warning

Read the installation instructions before connecting the system to the power source. Statement 1004

Note The installation must comply with all required electrical codes applicable at the installation site.

Connecting Routers to AC Power

If your router uses AC power, connect it to a 15 A, 120 VAC (10 A, 240 VAC) circuit with overcurrent protection.

Note The input voltage tolerance limits for AC power are 85 and 264 VAC.

Warning

AC connected units must have a permanent ground connection in addition to the power cable ground wire.

 

 

NEBS-compliantgrounding satisfies this requirement.Statement 284

 

 

 

 

 

 

Warning

This product relies on the building’s installation for short-circuit(overcurrent) protection. Ensure that the

 

 

protective device is rated not greater than:

 

 

15A, 120VAC (10A, 240VAC). Statement 1005

 

 

 

Connecting the Router to DC Power

If your router has a DC-inputpower supply, follow the directions in this section for proper wiring.

Warning

This product relies on the building’s installation for short-circuit(overcurrent) protection. Ensure that the

 

 

protective device is rated not greater than:

 

 

15A, 60VDC. Statement 1005

 

 

 

 

 

 

Warning

Use copper conductors only. Statement 1025

 

 

 

DC Wiring Requirements

A Cisco router with a DC-inputpower supply requires copper wire for the power connections.Table 2 summarizes the wiring requirements for Cisco 2600XM series and Cisco 2612 routers with aDC-inputpower supply.

Note For installations compliant with the National Electric Code, AWG 14 (2.0 mm2) wire is required for DC input and safety ground wire.

Table 2

DC Wiring Requirements for Cisco 2610, Cisco 2620, and Cisco 2650 Series Routers

 

 

 

 

 

 

DC Power Source

DC Input

DC Input Wire Size1

Safety Ground Wire Size

Overcurrent Protection

Nominal 48 VDC

–48to–60VDC2, 4 A

AWG 18 (1.0 mm2)

AWG 14 (2.0 mm2)

15 A, maximum

1.See the note above this table for National Electric Code wire size requirements.

2.The input voltage tolerance limits for nominal 48-Vpower supplies are 38 and 72 VDC.

15

Wiring Procedure for Nominal 48 VDC Input

To connect the router to a DC power source, perform this procedure:

Step 1

Warning

Tip

Step 2

Step 3

Warning

Warning

Warning

Caution

Caution

Remove power from the DC circuit. To ensure that power is removed from the DC circuit, locate the circuit breaker for the DC circuit, switch the circuit breaker to the OFF position, and tape the circuit-breakerswitch in the OFF position.

Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Statement 1003

Secure all power cabling when installing this unit to avoid disturbing field-wiringconnections.

Strip the wires to the appropriate length for the terminal block on the power supply.

Connect the DC power input wires to the terminal block, as shown in Figure 12.

When stranded wiring is required, use approved wiring terminations, such as closed-looporspade-typewith upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the insulation and conductor.Statement 1002

The illustration shows the DC power supply terminal block. Wire the DC power supply as illustrated. The proper wiring sequence is ground to ground, positive to positive, and negative to negative. The ground wire should always be connected first and disconnected last. Statement 239

An exposed wire lead from a DC-inputpower source can conduct harmful levels of electricity. Be sure that no exposed portion of theDC-inputpower source wire extends from the terminal block plug.Statement 122

The terminal arrangement on your router may not be identical to the arrangement shown in the figures. You must connect the positive, negative, and ground wires according to the labels on the terminals.

Do not overtorque the terminal block captive thumbscrew or terminal block contact screws. The recommended torque is 8.0 ± 0.5inch-lb(0.9± 0.05N-m).

Figure 12 DC Power Connections for Cisco 2600XM Series and Cisco 2612 Routers (Typical)

On/off

Negative

 

Ground

Positive

 

switch

 

 

 

 

72363

 

 

 

Terminal

 

-

+

block

 

 

Step 4 Secure the wires using cable ties.

Step 5 Turn on power to the DC circuit.

16

Connecting Routers to the Cisco Redundant Power System

If your router uses the Cisco Redundant Power System (RPS), refer to the Cisco RPS Hardware Installation Guide for instructions about the power connections. To locate these documents, see the“Where to Go Next” section on page 24.

WAN, LAN, and Voice Connections

The connections and cables listed here are described in detail in the following documents:

Cisco 2600 Series Hardware Installation Guide

Cisco Network Modules Hardware Installation Guide

Cisco Interface Cards Installation Guide

Cisco Modular Access Router Cable Specifications

To locate these documents, see the “Where to Go Next” section on page 24.

Table 3 summarizes some typical WAN, LAN, and voice connections for Cisco 2600XM series and Cisco 2612 routers.

Table 3

WAN, LAN, and Voice Connections

 

 

 

 

 

 

Port or Connection

Port Type, Color

Connected To:

Cable

 

 

 

 

 

Ethernet

 

RJ-45,yellow

Ethernet hub or Ethernet switch

Straight-throughEthernet

 

 

 

 

T1/E1 WAN

RJ-48C/CA81A,blue

T1 or E1 network

RJ-48T1

 

 

 

 

 

Cisco serial

 

60-pinD-sub

CSU/DSU and serial network or

Cisco serial transition cable that matches

 

 

 

equipment

the signaling protocol (EIA/TIA-232,

 

 

 

 

EIA/TIA-449,V.35, X.21, orEIA-530)

Cisco Smart serial

Cisco Smart compact

CSU/DSU and serial network or

and the serial port operating mode (DTE

 

 

connector, blue

equipment (For WIC-2Tand

 

 

or DCE).1

 

 

 

WIC-2A/Sonly)

 

 

 

 

 

 

 

 

 

DSL

 

RJ-11C/CA11A,

Network demarcation device for

RJ-11

 

 

lavender

service provider’s DSL interface

 

 

 

 

 

T1 digital voice

RJ-48C/CA81A,tan

Digital PBX

RJ-48T1 cable

 

 

 

 

Analog voice FXS

RJ-11,gray

Telephone, fax

RJ-11

 

 

 

 

Analog voice FXO

RJ-11,pink

Central office, analog PBX

RJ-11

 

 

 

 

Analog voice E&M

RJ-11,brown

Analog PBX

RJ-11

 

 

 

 

BRI S/T WAN

RJ-48C/CA81A,orange

NT1 device or private integrated

RJ-48

(external NT1)

 

network exchange (PINX)

 

 

 

 

 

BRI U WAN

RJ-49C/CA-A11,red

ISDN network

RJ-49

(built-inNT1)

 

 

 

 

 

 

 

 

CT1/PRI

 

T1

External T1 CSU

DB-15T1 serial cable

 

 

 

 

CT1/PRI-CSU

T1

RJ-48C/CA81Ainterface

RJ-48straight-through

 

 

 

 

 

CE1/PRI

 

E1

E1 network

DB-15to BNC,DB-15toDB-15,

 

 

 

 

DB-15to twinax, orDB-15toRJ-45

 

 

 

 

 

Token Ring

 

UTP, purple

Token Ring device

RJ-45Token Ring cable

 

 

STP, purple

 

 

 

 

 

 

56/64-kbpsDSU/CSU

8-pinmodular, blue

RJ-48Sinterface

RJ-48straight-through

 

 

 

 

 

1. See the Cisco Modular Access Router Cable Specifications document for information about selecting these cables.

17

5 Power Up the Router

Checklist for Power-Up

You are ready to power up the Cisco router after you have completed the following steps:

Chassis is securely mounted and grounded.

Power and interface cables are connected.

Your PC terminal emulation program is configured for 9600 baud, 8 data bits, 1 stop bit, and no parity.

You have selected passwords for access control.

You have determined the IP addresses for the Ethernet and serial interfaces.

Front Panel Indicators

The following indicator LEDs provide power, activity, and status information:

POWER (green)—Litwhen power is on

RPS (green)

Off—Noredundant power supply (RPS) is present

Blinking—Systemis booted, RPS is present, RPS failure

Continuous on—Systemis booted, RPS is present, no RPS failure

ACTIVITY (green)

Slow, steady blinking—Systemis booting

Blinks during system activity, such as interrupts and packet transfers

Power-UpProcedure

To power up your Cisco router and verify that it goes through its initialization and self-test,perform this procedure. When the procedure is finished, the Cisco router is ready to configure.

Note To view the boot sequence through a terminal session, you must have a console connection to the Cisco routerbefore it powers on.

Step 1 Make sure that your PC is powered up and connected as described in the“Checklist for Power-Up” section.

Step 2 Move the power switch to the ON position.

The green POWER or PWR LED on the front of the chassis comes on and the fan operates. If this does not happen, see the power-upprocedure in theCisco 2600 Series Routers Hardware Installation Guide.

Messages begin to appear in your terminal emulation program window.

Caution Do not press any keys on the keyboard until the messages stop. Any keys pressed during this time are interpreted as the first command typed when the messages stop, which might cause the router to power off and start over. It takes a few minutes for the messages to stop.

18

You may see different startup messages:

If you see the following messages, the router has booted with a configuration file and is ready for initial configuration using the Cisco Router and Security Device Manager (SDM):

yourname con0 is now available

Press RETURN to get started.

See the “Initial Configuration Using Cisco Router and Security Device Manager” section on page 20 to learn how to configure your router using SDM or to learn how to obtain SDM and install it on your router.

If you see the following messages, the router has booted and is ready for initial configuration using the setup command facility or the command-lineinterface (CLI):

---System Configuration Dialog---

At any point you may enter a question mark '?' for help.

Use ctrl-cto abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes/no]:

To learn how to use the setup command facility to configure the router, see the “Initial Configuration Using the Setup Command Facility” section on page 20. To learn how to use the CLI to configure the router, see the“Initial Configuration Using the CLI (Manual Configuration)” section on page 22.

Note If therommon 1> prompt appears, your system has booted in ROM monitor mode. For information on the ROM monitor, see the router rebooting and ROM monitor information in theCisco IOS Configuration Fundamentals Configuration Guide for your Cisco IOS software release.

For information about accessing this document, see the “Where to Go Next” section on page 24.

6 Perform Initial Configuration

You can configure your router by using one of the following methods:

Cisco Router and Security Device Manager (SDM)—Ifyour router was purchased with a VPN bundle, SDM is installed on the router. For instructions on configuring your router by using SDM, refer to theCisco Router and Security Device Manager (SDM) Quick Start Guide that shipped with your router. See the“Initial Configuration Using Cisco Router and Security Device Manager” section on page 20 for additional information.

Setup command facility—Youcan use the setup command facility to configure basic router information. After the configuration file has been created, you can use the CLI or SDM to perform additional configuration. See the“Initial Configuration Using the Setup Command Facility” section on page 20 for additional information.

Command-lineinterface(CLI)—Ifyou prefer to use the Cisco IOS CLI, see the“Initial Configuration Using the CLI (Manual Configuration)” section on page 22 for instructions on how to use the CLI.

Note You need to understand how interfaces are numbered so that you know which interface you are configuring. If you need help with interface and port numbering, see the“Interface Numbering” section on page 23.

19

Initial Configuration Using Cisco Router and Security Device Manager

If the following messages appear at the end of the startup sequence, Cisco Router and Security Device Manager (SDM) is installed on your router:

yourname con0 is now available

Press RETURN to get started.

For instructions on configuring your router by using SDM, refer to the Cisco Router and Security Device Manager (SDM) Quick Start Guide.

Tip If the messages above do not appear, SDM and the Cisco Router and Security Device Manager (SDM) Quick Start Guidewere not shipped with your router. If you want to use SDM, you can download the latest version of SDM and instructions for installing it on your router from the following location:

http://www.cisco.com/pcgi-bin/tablebuild.pl/sdm

To obtain the SDM quick start guide, SDM release notes, and other SDM documentation, go to www.cisco.com/go/sdm and click the Technical Documentation link.

Initial Configuration Using the Setup Command Facility

This section shows how to use the setup command facility to configure a host name for the router, set passwords, and configure an interface for communication with the management network. If you see the following messages at the end of the startup sequence, the setup command facility has been invoked automatically:

---System Configuration Dialog---

At any point you may enter a question mark '?' for help.

Use ctrl-cto abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes/no]:

The setup command facility prompts you for basic information about your router and network, and it creates an initial configuration file.The prompts vary, depending on your router model, the installed interface modules, and the software image. The following example and the user entries (in bold) are shown as examples only.

For a description of interface numbering, see the “Interface Numbering” section on page 23.

Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again. PressCtrl-C,and entersetup at the privileged EXEC mode prompt (2600#).

Step 1 To proceed using the setup command facility, enteryes.

Would you like to enter the initial configuration dialog? [yes/no]: yes

Step 2 When the following messages appear, pressReturn to enter basic management setup:

At any point you may enter a question mark '?' for help.

Use ctrl-cto abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: yes

20

Step 3 Enter a host name for the router (this example uses2610):

Configuring global parameters:

Enter host name [Router]: 2610

Step 4 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration:

The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration.

Enter enable secret: xxxxxx

Step 5 Enter an enable password that is different from the enable secret password. This password isnot encrypted (less secure) and can be seen when viewing the configuration:

The enable password is used when you do not specify an

enable secret password, with some older software versions, and some boot images.

Enter enable password: xxxxxx

Step 6 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port:

The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: xxxxxx

Step 7 Respond to the following prompts as appropriate for your network:

Configure SNMP Network Management? [yes]:

Community string [public]:

Step 8 A summary of the available interfaces appears:

Note The interface numbering that appears is dependent on the type of Cisco modular router platform and on the installed interface modules and cards.

Current interface summary

 

 

Controller

Timeslots

D-ChannelConfigurable modes

Status

T1 0/0

24

23

pri/channelized

Administratively up

Any interface listed

with OK? value "NO" does not

have a valid configuration

Interface

IP-Address

OK?

Method

Status

Prol

FastEthernet0/0

unassigned

NO

unset

up

up

FastEthernet0/1

unassigned

NO

unset

up

dow

Step 9 Select one of the available interfaces for connecting the router to the management network:

Enter interface name used to connect to the

management network from the above interface summary: fastethernet0/0

Step 10 Respond to the following prompts as appropriate for your network:

Configuring interface FastEthernet0/0:

Use the 100 Base-TX(RJ-45)connector? [yes]:yes

Operate in full-duplexmode? [no]:no

Configure IP on this interface? [yes]: yes

IP address for this interface: 172.1.2.3

Subnet mask for this interface [255.255.0.0] : 255.255.0.0

Class B network is 172.1.0.0, 16 subnet bits; mask is /16

21

Step 11 The configuration appears:

The following configuration command script was created:

hostname 2610

enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx

line vty 0 4 password xxxxxx

snmp-servercommunity public

!

no ip routing

!

interface FastEthernet0/0 no shutdown

media-type100BaseXhalf-duplex

ip address 172.1.2.3 255.255.0.0

!

interface FastEthernet0/1 shutdown

no ip address

!

end

Step 12 Respond to the following prompts. Select [2] to save the initial configuration.:

[0]Go to the IOS command prompt without saving this config.

[1]Return back to the setup without saving this config.

[2]Save this configuration to nvram and exit.

Enter your selection [2]: 2

Building configuration...

Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started! RETURN

Step 13 The user prompt appears.

2610>

After you complete the initial configuration tasks, your Cisco router is ready to configure for specific functions. See the “Where to Go Next” section on page 24 for information about locating documentation for advanced configuration procedures.

Initial Configuration Using the CLI (Manual Configuration)

This section shows how to bring up a command-lineinterface (CLI) prompt for configuration using the CLI, and it directs you to documentation for the CLI configuration.You can use the CLI if you see the following messages at the end of the startup sequence:

---System Configuration Dialog---

At any point you may enter a question mark '?' for help.

Use ctrl-cto abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes/no]:

If these messages do not appear, SDM and a default configuration file have been installed on the router at the factory. To use SDM to configure the router, see the “Initial Configuration Using Cisco Router and Security Device Manager” section on page 20.

22

For interface numbering information, see the “Interface Numbering” section on page 23.

Step 1 To proceed with manual configuration using the CLI, enterno.

Would you like to enter the initial configuration dialog? [yes/no]: no

Step 2 PressReturn to terminate autoinstall and continue with manual configuration.

Would you like to terminate autoinstall? [yes] Return

Several messages are displayed, ending with a line similar to the following:

...

Copyright (c) 1986-2000by cisco Systems, Inc.

Compiled <date> <time> by <person>

Step 3 PressReturn to bring up theRouter> prompt.

...

flashfs[4]: Initialization complete. Router>

Step 4 Enter privileged EXEC mode.

Router> enable

Router#

Note To avoid losing work you have completed, be sure to save your configuration occasionally as you proceed. Use thecopy running-config startup-config command to save the configuration to NVRAM.

For configuration using the CLI, refer to the applicable configuration procedures in the Software Configuration Guide: Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers. See the“Where to Go Next” section on page 24 for information about accessing this document.

7 Interface Numbering

Each individual interface (port) on Cisco 2600XM series and Cisco 2612 routers is identified by number as described in the following sections.

WAN and LAN Interface Numbering

Cisco 2600XM series and Cisco 2612 router chassis contain the following WAN and LAN interface types:

Built-inLAN interfaces: Ethernet, FastEthernet, Token Ring

Two or three slots in which you can install WAN interface cards (WICs)

One slot in which you can install a network module

The numbering format is Interface-type Slot-number/Interface-number.Two examples are:

Ethernet 0/0

Serial 1/2

The slot number is 0 for all built-ininterfaces and 0 for all WIC interfaces; the slot number is 1 for network module interfaces.

Interface (port) numbers begin at 0 for each interface type, and continue from right to left and (if necessary) from bottom to top.

Figure 13 shows a router of1-RUheight with:

A WIC in each WIC slot (containing interface Serial 0/0 in physical slot W0, and interface Serial 0/1 in physical slot W1)

A 4-serial-portnetwork module in slot 1 (containing the following ports: Serial 1/0, Serial 1/1, Serial 1/2, and Serial 1/3)

23

First built-inEthernetinterface—Ethernet0/0

Second built-inEthernetinterface—Ethernet0/1, or optionally in Cisco 2612 and Cisco 2613 only: Token Ring interface 0/0

Figure 13 Interface Numbering in Chassis with 1-RUHeight

1 2

SERIAL

 

 

A/S

 

 

3

CN/LP RXC

RXD TXC TXD

 

2

CN/LP

RXC

RXD TXC TXD

 

 

1

CN/LP RXC

RXD TXC

 

 

W1

 

TXD

 

 

 

 

0

CN/LP RXC

RXD TXC TXD

 

 

 

 

 

 

 

 

 

EN

10

9

8

7

 

CONN

SERIAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

W0

CONN

SERIAL

Cisco

2612

 

 

 

W0

 

 

 

 

 

 

 

 

 

 

LINK

TOKEN RING

 

 

W0

 

 

 

 

 

 

 

 

 

 

0/0 ACT

LINK

 

 

 

 

 

 

 

ETHERNET

 

 

 

 

 

 

 

0/0 ACT

CONSOLE

 

 

 

 

 

 

 

AUX

 

 

 

 

 

 

 

 

 

6

5

3

 

 

 

4

100-

1A

240V–

50/60 Hz

47 W

28308

Voice Interface Numbering

Voice interfaces are numbered as follows: chassis-slot/voice-module-slot/voice-interface

If a 4-channelvoice network module is installed in chassis slot 1, the voice interfaces are:

1/0/0—Chassisslot 1/Voice module slot 0/Voice interface 0

1/0/1—Chassisslot 1/Voice module slot 0/Voice interface 1

1/1/0—Chassisslot 1/Voice module slot 1/Voice interface 0

1/1/1—Chassisslot 1/Voice module slot 1/Voice interface 1

8 Where to Go Next

For additional detailed configuration procedures, refer to the appropriate Cisco 2600 series documentation or Cisco IOS software documentation, available online on Cisco.com:

Tip See the“Obtaining Additional Publications and Information” section on page 27 for help in locating these documents.

To access documentation on Cisco.com:

For Cisco 2600XM series platform documentation, start on Cisco.com at http://www.cisco.com, and select

Products & Services > Routers > Cisco 2600 Series Multiservice Platforms > Technical Documentation > Document type >

Document.

For Cisco IOS software documentation, start on Cisco.com at http://www.cisco.com, and selectProducts & Services > IOS Software > Cisco IOS Software Releases > Your Cisco IOS software release.

To get updated information about platform support for features, select Feature Navigator II, if you have an account on Cisco.com. You can also access Feature Navigator II at http://www.cisco.com/go/fn.

24

To access documentation using Cisco Connection Online (CCO):

For Cisco 2600XM series platform documentation, start on Cisco.com at http://www.cisco.com, and click the “Technical Documentation” tab under Useful Links. Under the Product Documentation heading, navigate to Modular Access Routers and to the documentation for your router.

For Cisco IOS software documentation, start on Cisco.com at http://www.cisco.com, and click the “Technical Documentation” tab under Useful Links. Under the Product Documentation heading, navigate to the Cisco IOS software documentation for the Cisco IOS software release that is installed on your router.

9 Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool: http://www.cisco.com/en/US/partner/ordering/index.shtml

Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208or, elsewhere in North America, by calling 800553-NETS(6387).

10 Documentation Feedback

You can send comments about technical documentation to bug-doc@cisco.com.

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

25

11 Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day,award-winningtechnical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.

Cisco Technical Support Website

The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool automatically provides recommended solutions. If your issue is not resolved using the recommended resources, your service request will be assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

To open a service request by telephone, use one of the following numbers:

Asia-Pacific:+61 2 8446 7411 (Australia: 1 800 805 227)

EMEA: +32 2 704 55 55

USA: 1 800 553 2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)—Yournetwork is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operationof an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commitfull-timeresources during normal business hours to resolve the situation.

Severity 3 (S3)—Operationalperformance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)—Yourequire information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

26

12 Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:

http://cisco.com/univercd/cc/td/doc/pcat/

Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:

http://www.ciscopress.com

Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores ofin-depthonline resources. You can access Packet magazine at this URL:

http://www.cisco.com/packet

iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, usingreal-worldcase studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

World-classnetworking training is available from Cisco. You can view current offerings at this URL:http://www.cisco.com/en/US/learning/index.html

27

Corporate Headquarters

European Headquarters

Americas Headquarters

Asia Pacific Headquarters

Cisco Systems, Inc.

Cisco Systems International BV

Cisco Systems, Inc.

Cisco Systems, Inc.

170 West Tasman Drive

Haarlerbergpark

170 West Tasman Drive

168 Robinson Road

San Jose, CA 95134-1706

Haarlerbergweg 13-19

San Jose, CA 95134-1706

#28-01Capital Tower

USA

 

1101 CH Amsterdam

USA

 

Singapore 068912

www.cisco.com

The Netherlands

www.cisco.com

www.cisco.com

 

Tel:

408 526-4000

www-europe.cisco.com

Tel:

408 526-7660

Tel:

+65 6317

7777

 

800 553-NETS(6387)

Tel:

31 0 20 357 1000

Fax:

408 527-0883

Fax:

+65 6317

7799

Fax:

408 526-4100

Fax:

31 0 20 357 1100

 

 

 

 

 

Cisco Systems has more than 200 offices in the following countries. Addresses, phone numbers, and fax numbers are listed on the

C i s c o W e b s i t e a t w w w . c i s c o . c o m / g o / o f f i c e s

Argentina • Australia • Austria • Belgium • Brazil • Bulgaria • Canada • Chile • China PRC • Colombia • Costa Rica • Croatia • Cyprus • Czech Republic • Denmark Dubai, UAE • Finland • France • Germany • Greece • Hong Kong SAR • Hungary • India • Indonesia • Ireland • Israel • Italy • Japan • Korea • Luxembourg • Malaysia Mexico • The Netherlands • New Zealand • Norway • Peru • Philippines • Poland • Portugal • Puerto Rico • Romania • Russia • Saudi Arabia • Scotland • Singapore Slovakia • Slovenia • South Africa • Spain • Sweden • Switzerland • Taiwan • Thailand • Turkey • Ukraine • United Kingdom • United States • Venezuela • Vietnam Zimbabwe

CCVP, the Cisco logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Ne Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R)

Printed in the USA on recycled paper containing 10% postconsumer waste.

78-13148-12DOC-7813148=