DQ-1000/1100/1200
BEFORE USING THE UNIT FOR THE FIRST TIME…
1.Remove the battery compartment cover on the back of the unit.
2.Remove the insulating paper from between the batteries and contacts.
3.Replace the battery compartment cover.
4.Press reset button.
5.Set the time.
GENERAL GUIDE
•The configuration of your clock may differ somewhat from that shown in the illustration.
•The display illuminates for a few seconds whenever you press the Snooze/ Light button.
•The Snooze/Light button 1 of the DQ-1200 employs a
“ touch sensor,” so all you need do is touch it to turn on the light or stop the alarm.
DQ-1000 |
|
|
|
|
1Snooze/Light |
|
4 Reset |
|
button |
|
button |
PM |
Alarm time |
|
5 |
AM |
|
||
|
RESET TIMESET |
Time |
|
|
|
||
|
2 |
|
|
|
|
setting |
|
|
Alarm On/ |
|
|
|
|
dial |
|
ALARM |
Off switch |
|
|
SET |
|
|
|
|
3 Alarm |
6 Battery compartment cover |
|
Current time |
setting dial |
||
|
|
|
|
DQ-1100 |
|
|
|
1 |
|
|
5 |
|
|
|
|
PM |
ALARM |
|
|
|
SET |
|
|
|
2 |
|
TIME SET |
AM |
|
|
|
|
|
|
RESET |
|
3 |
6 |
4 |
DQ-1200 |
|
|
4 |
|
|
|
|
|
PM |
|
|
AM |
2 |
TIME SET |
5 |
|
ALARM |
|
|
|
SET |
|
|
1 |
3 |
6 |
|
The operational procedures for DQ-1000, DQ-1100 and DQ-1200 are identical. All of the illustrations in this manual show DQ-1000.
SETTING THE TIME
[Back]
Time setting dial
RESET TIMESET
Increase Decrease
Rotate the time setting dial to the left to increase the number(s). Rotate the dial to the right to decrease the number(s). Rotating the dial left or right as far as it goes causes the setting to jump on 10-minute steps.
•The time setting is changed minute-by- minute.The hour setting is changed automatically whenever a change in the minutes increases past 59 minutes or decreases past 00 minutes.
•The seconds are reset to “00” whenever you change the minutes setting.
•The time display uses a 12-hour format, so morning is indicated by “AM” and evening is indicated by “PM”.
USING THE ALARM
The alarm of this clock features a Snooze Function, which lets you catch a few more minutes sleep. For full details on how to use this function, see “To use the alarm”.
To set the alarm
Snooze/Light
button |
Alarm time |
PM |
|
|
AM |
|
ALARM |
|
SET |
Alarm |
Alarm on |
setting dial |
indicator |
|
Alarm On/Off |
|
switch |
Decrease Increase
Rotate the alarm setting dial to the right to increase the alarm time by one minute, or to the left to decrease the alarm time by one minute. Rotating the dial left or right as far as it goes causes the setting to jump in 10-minute steps.
•The hour setting changes automatically whenever a change in the minutes increases past 59 minutes or decreases past 00 minutes.
•The time display uses a 12-hour format, so morning is indicated by “AM” and evening is indicated by “PM”.
|
ALARM |
|
|
|
|
SET |
|
|
|
To switch the alarm on and off |
|
|||
ON |
ON |
Slide the Alarm On/Off switch to the ON position |
||
to switch the alarm on, or to the OFF position to |
||||
|
|
|||
|
|
switch it off. |
|
|
|
|
• When you |
switch the alarm on, the alarm on |
|
OFF |
OFF |
indicator “ |
” appears on the display. |
|
On |
Off |
|
|
To use the alarm
1.Set the alarm time and switch the alarm on.
2.When the alarm time you set is reached, the alarm starts to sound. It continues for about one minute or until you stop it by pressing the Snooze/
Light button.
•When the alarm starts to sound, the alarm on indicator flashes on the display. This indicates that the Snooze function is activated.
3.About four minutes after you press the Snooze/Light button, the alarm starts to sound again.
4.The above repeats up to seven times, or until you switch the alarm off (by sliding the Alarm on/off switch to the OFF position).
•You can stop the repeating alarm at any time by sliding the Alarm on/off switch to the OFF position.
•The beep pattern of the alarm changes (becomes faster) as the alarm sounds. The pattern changes up to five times.
BATTERY REPLACEMENT
Replace the batteries whenever the display of the clock becomes dim and difficult to read, or when the display light fails.
[Back]
Reset button
RESET TIMESET
Battery compartment
1.Open the battery compartment cover on the back of the clock by sliding it in the direction indicated by the arrow on the cover.
2.Remove the two old batteries.
3.Load two new batteries, making sure that their positive (+) and negative (-) ends are facing in the correct directions.
4.Replace the battery compartment cover.
5.Press reset button to reset the digital display information.
6.Set the time.