Loading...
MA0212-A
USER’S GUIDE LD (10B-A)
About This Manual
|
• The operational procedures for Modules 2482, 2600, |
|
|
2675 and 2676 are identical. All of the illustrations in this |
|
|
manual show Module 2482. |
|
|
• Button operations are indicated using the letters shown |
|
|
in the illustration. |
|
|
• Each section of this manual provides you with the |
|
|
information you need to perform operations in each |
|
[Modules 2482, 2600, 2675] |
mode. Further details and technical information can be |
|
found in the “Reference” section. |
||
|
[Module 2676]
General Guide
•Press B to change from mode to mode.
•After you perform an operation in any mode, pressing Breturns to the Timekeeping Mode.
•In any mode, press Ato illuminate the display.
Timekeeping Mode |
Alarm Mode |
Press .
Timekeeping
PM indicator
Day of the week Day
Hour 
Minutes
Seconds
Backlight Precautions
Use the Timekeeping Mode to view the current time and date.
• Day of the week is displayed as follows.
SU: Sunday |
MO: Monday |
TU: Tuesday |
WE: Wednesday |
TH: Thursday |
F R : Friday |
SA: Saturday |
|
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press C to switch between the 12-hour and 24-hour formats.
•With the 12-hour format, the PM indicator (P/
) appears for times in the range of noon to 11:59 p.m. and no indicator appears for times in the range of midnight to 11:59 a.m.
•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, with 24/
indicator.
The backlight uses an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark.
•The electro-luminescent panel that provides illumination loses power after very long use.
•The illumination provided by the backlight may be hard to see when viewed under direct sunlight.
•The watch may emit an audible sound whenever the display is illuminated. This is due to vibration of the EL panel used for illumination, and does not indicate malfunction.
•Frequent use of the backlight shortens the battery life.
Stopwatch Mode |
Time Setting Mode |
Alarm
Mode indicator
Hour Minutes
Alarm on
indicator Hourly time signal on indicator
When the Daily Alarm is turned on, the alarm sounds for 20 seconds at the preset time each day. When the Hourly Time Signal is turned on, the watch beeps every hour on the hour.
•An alarm setting (and an Hourly Time Signal setting) is
available in the Alarm Mode, which you enter by pressing B.
To set the alarm time
1.Hold down Awhile in the Alarm Mode until the hour digits start to flash on the display. The hour digits flash because they are selected.
• This operation automatically turns on the alarm.
[Module 2676]
2.Press Ato change the selection in the following sequence.
• Pressing Aalso illuminates the display.
Hour |
|
|
Minutes |
|
|
Normal Alarm Mode (No digit flashes)
3.Press Cto increase the selected digits. Holding down C changes the number at high speed.
•The format (12-hour and 24-hour) of the alarm time matches the format you select for normal timekeeping.
•When setting the alarm time using the 12-hour format, take care to set the time correctly as morning or afternoon (P/
).
4.After you set the alarm time, press Ato return to the Alarm Mode.
To stop the alarm
Press Ato stop the alarm after it starts to sound.
To switch the Daily Alarm and Hourly Time Signal on and off
Press Cwhile in the Alarm Mode to change the status of the Daily Alarm and Hourly Time Signal in the following sequence.
[Alarm on indicator/Hourly Time Signal on indicator]
[Modules 2482, |
Both on |
Both off |
Daily Alarm |
Hourly Time |
2600, 2675] |
|
|
only |
Signal only |
[Module 2676] |
Both on |
Both off |
Daily Alarm |
Hourly Time |
|
|
|
only |
Signal only |
To test the alarm
Hold down C while in the Alarm Mode to sound the alarm.
1
Loading...