Casio 1914 User Manual

Size:
94.3 Kb
Download
Alarm Mode
The operational procedures for Module 1913 and 1914 are identical. All of the illustrations in this manual show Module 1913.

Module No.1913/1914

GENERAL GUIDE

PressCto change from mode to mode.

The watch automatically returns to the Timekeeping Mode if you do not perform any button operation for two or three minutes in any other mode.The animated display shows different animated characters and graphics, depending on the mode and the operation being performed.

In any mode, pressBto illuminate the display for about two seconds.

Countdown Alarm Mode

Timekeeping Mode

Animated display

Stopwatch Mode

[Module 1914]

[Module 1913]

TIMEKEEPING MODE

Animated Display

Color mark

 

Month

Day

Minutes

Hour Seconds PM indicator

In the Timekeeping Mode, press Dto switch between the12-hourand24-hourformats. With the12-hour

format, the animated display shows repeating charac-

ters that indicate the current day of the week. With the 24-hourformat, it shows aG-mark.

To set the time and date

1.Hold down Awhile in the Timekeeping Mode. The seconds digits flash on the display because they areselected.

2.Press Cto change the selection in the following sequence.

Seconds Hour Minutes

 

Day

 

 

Month

 

 

Year

 

 

 

 

 

3.While the seconds digits are selected (flashing), press Dto reset the seconds to “00”. If you pressDwhile the seconds count is in the range of 30 to 59, the seconds are reset to “00” and 1 is added to the minutes. If the seconds count is in the range of 00 to 29, the minutes count is unchanged.

4.While any other digits (besides seconds) are selected (flashing), press Dto increase the number. Holding downDchanges the current selection at high

speed. 5. After you set the time and date, press Ato return to the Timekeeping Mode.

 

The day of the week is automatically set in accordance with the date.

 

The date can be set within the range of January 1, 1995 to December 31, 2039.

 

If you do not operate any button for a few minutes while a selection is flashing,

the flashing stops and the watch goes back to the Timekeeping Mode automati-

 

cally.

ALARM MODE

Current time

AM indicator

Hour Minutes

Hourly time

signal on Alarm on indicator indicator

When the Daily Alarm is switched on, the alarm sounds for 20 seconds at the preset time each day. Press any button to stop the alarm after it starts to sound.

When the Hourly Time Signal is switched on, the watch beeps every hour on the hour.

To set the alarm time

1.Hold down Awhile in the Alarm Mode. The hour digits flash on the display because they areselected. At this time the Daily Alarm is switched on automati-

cally.

2.Press Cto change the selection in the following sequence.

Hour Minutes

3. Press Dto increase the selected digits. Holding downDchanges the selection

at high speed.

 

 

The format (12-hourand24-hour)of the alarm time matches

the format you

select for normal timekeeping.

 

 

When setting the alarm time using the 12-hourformat, take care to set the time correctly as morning (A) or afternoon (P).

4. After you set the alarm time, press Ato return to the Alarm Mode.

If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Alarm Mode automatically.

To switch the Daily Alarm and Hourly Time Signal on and off

Press Dwhile in the Alarm Mode to change the status of the Daily Alarm and Hourly Time Signal in the following sequence.

 

[Alarm ON Indicator/Hourly Time Signal ON Indicator]

 

 

Both ON

Both OFF

Daily Alarm only

Hourly Time

 

 

 

Signal only

To test the alarm

Hold down Dwhile in the Alarm Mode to sound the alarm.

COUNTDOWN ALARM MODE

Current time

Minutes

Seconds

The countdown timer can be set within a range of 1 minute to 60 minutes. When the countdown reaches zero, an alarm sounds for 10 seconds or until you press any button.

To set the countdown time

1.Hold down Awhile in the Countdown Alarm Mode. The minutes digit flashes on the display because it isselected.

2.Press Dto increase the selected number. Holding downDchanges the selection at high speed.

3.After you set the countdown time, press Ato return

to the Countdown

Alarm Mode.

 

If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Countdown Alarm Mode automatically.

To use the countdown timer

1.Press Dwhile in the Countdown Alarm Mode to start the countdown timer.

2.Press Dagain to stop the countdown timer.

 

 

 

 

 

You can continue countdown timer operation by pressing D.

3. Stop the timer and then press Ato reset the countdown

time to its starting

 

value.

 

 

 

When the countdown reaches zero, an alarm sounds for 10 seconds or until you stop the alarm by pressing any button. The countdown time is automatically reset to its starting value after the alarm stops.

About countdown indicators

An audible beep, the EL backlight, and the color marks on the display keep you informed about the progress of the countdown as noted in the following table.

Remaining

Audible beep

EL Backlight

Color mark

(Module 1913 Only)

 

 

 

Start (pressing D)

1 second

1 second

 

 

 

 

 

5'00"

1 second

1 second

 

 

 

 

 

Time up (00'00")

10 seconds

2 seconds

 

When the starting value is five minutes or less, the color marks start from center.

 

STOPWATCH MODE

Hours

The Stopwatch Mode lets you measure elapsed time,

 

split times, and two finishes. The range of the stop-

 

watch is 23 hours, 59 minutes, 59.99 seconds.

 

To measure elapsed time

 

1. Press Dto start the stopwatch.

 

2. Press Dto stop the stopwatch.

 

You can resume the measurement operation by press-

Minutes

ingDagain.

3. Press Ato clear the stopwatch to all zeros.

 

Seconds

 

To record split times

 

1/100 second

1. Press Dto start the stopwatch.

2. Press Ato display the timing up to that point. Stop-

 

watch timing continues internally.

3. Press Ato clear the split time and to continue time measurement on the display.

 

You can repeat steps 2 and 3 as many

times as you want.

4. Press Dto stop the time measurement.

5. Press Ato clear the stopwatch to all zeros.

To time first and second place finishes

1.Press Dto start the stopwatch.

2.Press Awhen the first finisher crossed the line, and record the time.

3.Press Dwhen the second finisher cross the line.

4.Press Ato display the finishing time of the second finisher.

5.Press Aagain to clear the stopwatch to all zeros.