Canon 300, 300P User Manual

INSTRUCTIONS

Please read this manual before using the scanner.

After you finish reading this manual, keep it in a safe place for future reference.

International ENERGY STAR® Office Equipment Program

As an ENERGY STAR® Partner, Canon Electronics Inc. has determined that this

machine meets the ENERGY STAR® Program guidelines for energy efficiency. The International ENERGY STAR® Office

Equipment Program is an international program that promotes energy saving through the use of computers and other office equipment.

The program backs the development and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment, such as computers, monitors, printers, fax, machine, copiers, and scanners. The standards and logos are uniform among participating nations.

Under factory default settings, the scanner will enter Low Power mode after 12 minutes of inactivity. Although you can change the period of time before the scanner enters Low Power mode to up to 230 minutes, we recommend using the default setting.

FCC REGULATIONS (For 120 V model)

Network Scanner, Model M11-1041/M11-1051 This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician

for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Canon U.S.A. Inc.

One Canon Plaza, Lake Success NY 11042, U.S.A. Tel. No. [phone]

RADIO INTERFERENCE REGULATIONS (For 120 V models)

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Industry Canada.

RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE (For 120 V models)

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée par l’Industrie Canada.

For CA, USA Only

Included battery contains Perchlorate Material - special handling may apply.

See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/ for detail.

European Union (and EEA) only

This symbol indicates that this product is not to be disposed of with your household waste, according

to the WEEE Directive (2002/96/EC) and your national law. This product should be handed over to a designated collection point, e.g., on an

authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service. For more information regarding return and recycling of WEEE products, please visit www.canon-europe.com/environment.

(EEA: Norway, Iceland and Liechtenstein)

Model Names

The following names may be provided for the safety regulations in each sales region of the Network Scanner. ScanFront 300: Model M11-1041

ScanFront 300P: Model M11-1051

Trademarks

•Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries.

•imageFORMULA is a trademark of Canon Electronics Inc.

•Microsoft, Windows, Internet Explorer, and Active Directory are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.

•Adobe, Acrobat, and Adobe Reader are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other countries.

•Other product and company names herein may be the trademarks of their respective owners.

Disclaimers

The information in this document is subject to change without notice.

CANON ELECTRONICS INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, EITHER EXPRESS OR IMPLIED, EXPECT AS PROVIDED HEREIN, INCLUDING WITHOUT LIMITATION, THEREOF, WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OF USE OR NONINFRINGEMENT. CANON ELECTRONICS INC. SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.

CANON ELECTRONICS INC. IS NOT LIABLE FOR THE STORAGE AND HANDLING OF DOCUMENTS SCANNED WITH THIS PRODUCT, OR THE STORAGE AND HANDLING OF RESULTING SCANNED IMAGE DATA.

IF YOU INTEND TO DISCARD THE ORIGINALS OF SCANNED DOCUMENTS, YOU THE CUSTOMER ARE RESPONSIBLE FOR INSPECTING THE SCANNED IMAGES AND VERIFYING THAT DATA IS INTACT. THE MAXIMUM LIABILITY OF CANON ELECTRONICS INC. UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY.

Copyright

libtiff

Copyright (c) 1988-1996 Sam Leffler Copyright (c) 1991-1996 Silicon Graphics, Inc.

Permission to use, copy, modify, distribute, and sell this software and its documentation for any purpose is hereby granted without fee, provided that (i) the above copyright notices and this permission notice appear in all copies of the software and related documentation, and (ii) the names of Sam Leffler and Silicon Graphics may not be used in any advertising or publicity relating to the software without the specific, prior written permission of Sam Leffler and Silicon Graphics.

THE SOFTWARE IS PROVIDED “AS-IS” AND WITHOUT WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

libjpeg

Portions of this software are based in part on the work of the Independent JPEG Group.

MD5

derived from the RSA Data Security, Inc. MD5 MessageDigest Algorithm

Copyright (c) 1998 - 2002, Paul Johnston & Contributors All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

Neither the name of the author nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Windows CE 6.0

Depending upon which components you are running, your product may contain the following third party technologies: Portions of this software are based on NCSA Mosaic. NCSA Mosaic was developed by the National Center for Supercomputing Applications at the University of Illinois at Urbana-Champaign.Distributed under a licensing agreement with Spyglass, Inc.

Contains security software licensed from RSA Data Security, Inc.

Portions of IPSec and related services jointly developed by Microsoft Corporation and Cisco Systems, Inc.

The names of actual companies and products mentioned herein may be the trademarks of their respective owners.

Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.

Copyright 2010 by CANON ELECTRONICS INC. All rights reserved.

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage or retrieval system without the prior written permission of CANON ELECTRONICS INC.

Introduction

Thank you for purchasing the Canon imageFORMULA ScanFront 300/300P network scanner.

Please read this manual thoroughly before using the scanner to familiarize yourself with its capabilities, and to make the most of its many functions. After reading this manual, store it in a safe place for future reference.

About ScanFront 300/300P

The ScanFront 300/300P is a network scanner that you can use without connecting to a computer.

You can transfer the data of an image scanned with the ScanFront 300/300P to a shared folder on a server PC or client PC on the network or to an FTP server*, send it to a printer for printing**, or deliver it to a remote location via e-mail or Internet fax service. When using the scanner without a network environment, you can also save the image files to USB memory.

*To send image files to a shared folder on a computer on a different segment of the network, the supplied ScanFront Service software must be installed on a computer on the network.

**To send image files to a printer, the supplied ScanFront Service software must be installed on a computer on the network.

Shared Folder

(Server PC, Client PC)

Network	Printer
	Save File
Save File	Send E-mail
FTP Server	Mail Server
	Internet Fax Service

ScanFront

USB Memory

Conceptual Diagram of the ScanFront

i

Manuals for the Scanner

The following manuals are provided with the Canon ScanFront 300/300P. Be sure to read these manuals thoroughly before using the scanner.

Setup Guide

Describes the procedure for setting up the scanner for scanning. Set up the ScanFront in accordance with the Setup Guide. For details on the ScanFront, refer to the

Operation Guide and ScanFront 300/300P INSTRUCTIONS (electronic manuals).

Operation Guide*

Provides an overview of the functions of the scanner, and describes the basic operations for using the ScanFront. For details on the settings of the ScanFront, refer to the

ScanFront 300/300P INSTRUCTIONS (electronic manual).

*The printed version of Operation Guide may vary depending on your region. PDF files of the Operation Guide in other languages can be found on the INSTRUCTIONS AND UTILITIES CD-ROM.

INSTRUCTIONS (Electronic Manual): This

Manual

Describes how to use the scanner, and includes instructions for configuring the scanner settings, as well as handling, maintenance, and troubleshooting information. This manual is stored as a PDF file on the supplied INSTRUCTIONS AND UTILITIES CD-ROM and requires Adobe Reader to open. (You can download Adobe Reader from the Adobe Web site.)

Symbols Used in This Manual

The following symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety.

WARNING

Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. To use the scanner safely, always pay attention to these warnings.

CAUTION

Indicates a caution concerning operations that may lead to injury to persons, or damage to property if not performed correctly. To use the scanner safely, always pay attention to these cautions.

IMPORTANT

Indicates operational requirements and restrictions. Be sure to read these items carefully to operate the scanner correctly, and avoid damage to the scanner.

Hint

Indicates a clarification of an operation, or contains additional explanations for a procedure. Reading these notes is highly recommended.

ii

How This Manual is Organized

This manual consists of the following chapters.

Chapter 1 Before Use

This chapter provides an overview of the ScanFront.

Chapter 2 Handling

This chapter describes the types of documents that can be scanned, and the basic operations of the scanner.

Chapter 3 ScanFront Setup

This chapter describes the setup procedures and Administrator Settings of the scanner.

Chapter 4 ScanFront Service

This chapter describes the how to use and configure ScanFront Service.

Chapter 5 Operating Procedures

This chapter describes the basic operating procedures for the scanner.

Chapter 6 Web Menu (Administrator Mode)

This chapter describes the Web menu for the administrator to configure settings.

Chapter 7 ScanFront Administration Tool

This chapter describes how to install and use ScanFront Administration Tool.

Chapter 8 Web Menu (User Mode)

This chapter describes the Web menu for the user to configure settings.

Chapter 9 Maintenance

This chapter describes how to clean the scanner and replace the consumable parts such as rollers.

Chapter 10 Troubleshooting

This chapter describes how to respond when problems occur or warning messages appear.

Chapter 11 Appendices

This chapter describes the scanner specifications.

iii

Table of Contents

Introduction...............................................................	i
Manuals for the Scanner ..........................................	ii
Symbols Used in This Manual..................................	ii
How This Manual is Organized................................	iii

Chapter 1 Before Use

1.	Important Safety Instructions............................	1-2
	Installation Location..............................................	1-2
	Power ...................................................................	1-2
	Moving the Scanner..............................................	1-3
	Handling ...............................................................	1-3
	About the Fingerprint Sensor
	(ScanFront 300P only)..........................................	1-5
	Disposal................................................................	1-5
2.	Features of the ScanFront 300/300P ...............	1-6
	ScanFront 300/300P.............................................	1-6
	ScanFront 300P....................................................	1-7
3.	Names and Functions of Parts .........................	1-8
	Front and Document Feed and Eject Trays..........	1-8
	Side and Rear.......................................................	1-9
4.	Network Environment .....................................	1-10
	Network Environment .........................................	1-10
	Directory Service Support...................................	1-10
	Limitations ..........................................................	1-11

Chapter 2 Handling

1.	Documents .......................................................	2-2
	Plain Paper...........................................................	2-2
	Business Card ......................................................	2-2
	Card......................................................................	2-3
2.	Preparing the Scanner .....................................	2-4
	Preparing the Document Feed Tray and
	Eject Tray .............................................................	2-4
	Feed Selection Lever............................................	2-5
	USB Port...............................................................	2-5
3.	Placing Documents ..........................................	2-6
	Placing a Document .............................................	2-6
	Placing a Folded Document .................................	2-7

	Placing a Long Document ....................................	2-7
	Placing a Card ......................................................	2-8
4.	Clearing a Paper Jam or Double Feed Error....	2-9
5.	Fingerprint Sensor (ScanFront 300P) ............	2-11
	Cautions for Handling the Fingerprint Sensor ....	2-11
	Fingerprint Authentication...................................	2-12

Chapter 3 ScanFront Setup

1. Before Setting Up the Scanner ........................	3-2
Installation Location..............................................	3-2
Connecting the AC Adapter..................................	3-3
Connecting the Network Cable.............................	3-3
2. Turning the Power ON and OFF ......................	3-4
Turning the Power ON..........................................	3-4
Turning the Power OFF ........................................	3-4
3. Configuring the Scanner Settings ....................	3-5
Administrator Settings ..........................................	3-5
Web Menu (Administrator Mode)..........................	3-6
4. Configuring Administrator Settings...................	3-8
Logging In to the Administrator Settings...............	3-8
Network Settings ..................................................	3-9
Administrator Password........................................	3-9
Backup/Restore Setting Information...................	3-10
Select Login Type...............................................	3-10
Roller Counter Reset ..........................................	3-11
Format ScanFront 300........................................	3-11
Touch Panel Adjustment ....................................	3-11
Display Language Setting...................................	3-12
Network Test ......................................................	3-12

Chapter 4 ScanFront Service

1.	About ScanFront Service .................................	4-2
2.	Installing ScanFront Service ............................	4-3
	System Requirements ..........................................	4-3
	Installation ............................................................	4-3
3.	ScanFront Service Setup .................................	4-6
	ScanFront Settings ...............................................	4-6
	Changing the Port Number Used for
	Communication.....................................................	4-6

iv

Chapter 5 Operating Procedures

1.	Flow of Scanner Operations.............................	5-2
2.	Turning the Power ON and OFF ......................	5-3
	Turning the Power ON..........................................	5-3
	Turning the Power OFF ........................................	5-3
3.	Login Screen ....................................................	5-4
	Login Screen Types..............................................	5-4
	When Using Server Authentication.......................	5-4
	List Type Login .....................................................	5-5
	Key in Type Login.................................................	5-6
	Fingerprint Authentication (Only Available
	with the ScanFront 300P).....................................	5-7
4.	Screen Displayed after Login ...........................	5-8
	Home Screen........................................................	5-8
	Job Button Screen ................................................	5-8
5.	User Settings Screen .......................................	5-9
	Change Password ................................................	5-9
	Fingerprint Registration ........................................	5-9
6.	Fingerprint Registration (Only Available
	with the ScanFront 300P)...............................	5-10
	Fingerprint Authentication...................................	5-10
	Registering a Fingerprint ....................................	5-11
7.	Scanning Procedures .....................................	5-13
	Scanning From the Home Screen ......................	5-13
	Scanning From the Job Button Screen...............	5-14
	Address Selection Screen ..................................	5-15
	USB Memory Screen..........................................	5-16
	Print Settings Screen..........................................	5-17
	Scanning.............................................................	5-18
8.	Registering and Editing Addresses ................	5-22
	Registering a New Address ................................	5-22
	Modifying an Address .........................................	5-25
	Copying an Address ...........................................	5-25
9.	Scan/Delivery Options ....................................	5-27
	Scan Settings .....................................................	5-28
	File Formats........................................................	5-32
	Security Settings for PDF Files...........................	5-33
	Delivery Options .................................................	5-34

Chapter 6 Web Menu (Administrator Mode)

1.	Web Menu Overview........................................	6-2
2.	Logging In to the Web Menu ............................	6-5
3.	User Administration..........................................	6-6
	Registering New Users.........................................	6-7
	Restricting User Functions .................................	6-10
	Editing Users ......................................................	6-11
	Exporting and Importing Users ...........................	6-12
4.	Address Book Settings...................................	6-14
	Registering New Addresses ...............................	6-15
	Copying Addresses ............................................	6-18
	Exporting and Importing Address Books ............	6-18
5.	Job Button Settings ........................................	6-20
	Registering New Job Buttons .............................	6-21
	Scan Settings Overview .....................................	6-22
	Copying Job Buttons ..........................................	6-26
	Editing Jobs ........................................................	6-27
	Exporting and Importing Job Buttons .................	6-27
6.	Device Configuration......................................	6-29
	Network Setting ..................................................	6-30
	Language/Timezone...........................................	6-30
	Device Operation................................................	6-31
	Login Options .....................................................	6-31
	Administrator Settings ........................................	6-32
7.	Server Settings...............................................	6-33
	E-mail Server/Fax Settings.................................	6-34
	Authentication Server .........................................	6-35
	Address Book Server..........................................	6-36
	FTP server..........................................................	6-36
	NTP Server.........................................................	6-37
	ScanFront Service Server ..................................	6-37
8.	System Settings .............................................	6-38
	Backup and Restore ...........................................	6-39
	Module Version Information/Update ...................	6-40
	Log Settings........................................................	6-42

v

Chapter 7 ScanFront Administration Tool

1.	About ScanFront Administration Tool...............	7-2
2.	Installing ScanFront Administration Tool..........	7-3
	System Requirements ..........................................	7-3
	Installation ............................................................	7-3
3.	ScanFront Administration Tool Setup...............	7-5
	Starting ScanFront Administration Tool................	7-5
	Registering ScanFront Scanners..........................	7-5
4.	Managing the ScanFront Scanners..................	7-6
	Selecting a ScanFront ..........................................	7-6
	Checking ScanFront Connections ........................	7-6
	Changing Passwords............................................	7-6
	Changing IP Addresses and Device Names ........	7-7
	Checking Detailed Information on the
	ScanFront .............................................................	7-7
	Displaying the Web Menu.....................................	7-7
	Batch Processing..................................................	7-7
	Importing/Exporting Administration Data ..............	7-8

Chapter 8 Web Menu (User Mode)

1.	Web Menu Overview ........................................	8-2
2.	Logging In to the Web Menu ............................	8-3
3.	User Settings....................................................	8-4
	User Settings ........................................................	8-5
4.	Address Book Settings .....................................	8-8
	Registering New Addresses ...............................	8-10
	Copying Addresses ............................................	8-13
	Exporting and Importing Address Books ............	8-13
5.	Job Button Settings ........................................	8-15
	Registering New Job Buttons .............................	8-17
	Scan Settings Overview .....................................	8-18
	Copying Job Buttons ..........................................	8-22
	Editing Jobs ........................................................	8-23
	Exporting and Importing Job Buttons .................	8-23

Chapter 9 Maintenance
1. Routine Cleaning..............................................	9-2
Cleaning the Scanner Unit....................................	9-2
Cleaning the Touch Panel ....................................	9-2
Cleaning the Fingerprint Sensor
(ScanFront 300P) .................................................	9-2
Cleaning the Scanning Glass and Rollers ............	9-3
Cleaning the Retard Roller ...................................	9-5
Cleaning the Feed Roller......................................	9-6
2. Replacing the Rollers and Document
Holding Guide ..................................................	9-8
Exchange Roller Kit ..............................................	9-8
Replacement Method ...........................................	9-8
Checking the Page Count and Resetting
the Counter...........................................................	9-9

Chapter 10 Troubleshooting

1.	Troubleshooting .............................................	10-2
2.	Error Messages (ScanFront)..........................	10-6
3.	Error Messages (Web Menu) .........................	10-9
4.	Adjusting the Touch Panel ...........................	10-11
5.	Initializing ScanFront....................................	10-13

Chapter 11 Appendices

1.	Specifications .................................................	11-2
	Unit Specifications ..............................................	11-2
	Network Specifications .......................................	11-3
	Transfer Destinations .........................................	11-3
	AC Adapter .........................................................	11-3
	Consumable Parts ..............................................	11-4
	External Dimensions...........................................	11-5
2.	Index ..............................................................	11-6

vi

Chapter 1 Before Use

1.	Important Safety Instructions ...........................	1-2
	Installation Location ..............................................	1-2
	Power ....................................................................	1-2
	Moving the Scanner ..............................................	1-3
	Handling ................................................................	1-3
	About the Fingerprint Sensor
	(ScanFront 300P only) ..........................................	1-5
	Disposal ................................................................	1-5
2.	Features of the ScanFront 300/300P...............	1-6
	ScanFront 300/300P .............................................	1-6
	ScanFront 300P ....................................................	1-7
3.	Names and Functions of Parts ........................	1-8
	Front and Document Feed and Eject Trays ..........	1-8
	Side and Rear .......................................................	1-9
4.	Network Environment ....................................	1-10
	Network Environment..........................................	1-10
	Directory Service Support ...................................	1-10
	Limitations ...........................................................	1-11

Chapter 1 Before Use

1. Important Safety Instructions

To ensure the safe operation of this scanner, be sure to read the safety warnings and precautions described below.

Installation Location

The performance of this scanner is affected by the environment in which it is installed. Make sure that the location where the scanner is installed meets the following environmental requirements.

●Provide adequate space around the scanner for operation, maintenance, and ventilation.

At least
15.75"
(40 cm)	At least
	23.62" (60 cm)

●Avoid installing the machine in direct sunlight. If this is unavoidable, use curtains to shade the scanner.

●Avoid locations where a considerable amount of dust accumulates.

●Avoid warm or humid locations, such as in the vicinity of a water faucet, water heater, or humidifier, and avoid locations where the fumes from ammonia, paint thinner, or other volatile chemicals may be present.

●Avoid locations that are subject to vibration.

●Avoid exposing the scanner to rapid changes in temperature. If the room in which the scanner is installed is cold but rapidly heated, water droplets (condensation) may form inside the scanner. This may result in a noticeable degradation in scanning quality.

The following conditions are recommended for

optimal scanning quality:

Room temperature: 10 °C to 32.5 °C (50 °F to 90.5 °F)

Humidity: 20% to 80% RH

●Avoid installing the scanner near equipment that generates a magnetic field (e.g. speakers, televisions, or radios).

Power

●Connect only to a power outlet of the rated voltage and power supply frequency (either 120 V, 60 Hz or 220-240 V, 50/60 Hz, depending on your region).

●Do not connect other electrical equipment to the same power outlet to which the scanner is connected. Also, when using an extension cord, make sure that the extension cord is rated for the current requirements of the scanner.

●Never try to disassemble the AC adapter or modify it in any way, as this is extremely dangerous.

●The power cord and AC adapter may become damaged if they are often stepped on or if heavy objects are placed on them. Continued use of a damaged power cord and AC adapter can lead to an accident, such as a fire or electrical shock.

●Do not use the power cord while it is coiled.

1-2

Chapter 1 Before Use

●Do not pull directly on the power cord. When disconnecting the power cord, grasp the plug and remove it from the outlet.

●Keep the area around the power plug clear of objects so that the power cord can be disconnected easily in an emergency.

●Use only the AC adapter provided with this scanner. Also, do not use the AC adapter provided with the scanner with any other electrical devices.

Model: MG1-4314

●If you have any questions regarding the power supply, contact your local authorized Canon dealer or service representative for further information.

Moving the Scanner

●When moving the scanner, always hold it with both hands to avoid dropping it. The weight of the scanner unit is approximately 7.9 lbs (3.6 kg).

●Before moving the scanner, make sure the document tray is closed and the interface cable and AC adapter are disconnected. If the scanner is transported with these items connected, the plugs and connectors may be damaged due to excessive force applied to them during movement.

Handling

WARNING

Note the following precautions whenever using the scanner. Failure to do so may result in a fire or electric shock.

■Never use alcohol, benzene, paint thinner, aerosol sprays, or any other highly flammable substance near the scanner.

■Do not cut, damage, or modify the power cord or AC adapter. Do not place heavy objects on the power cord or AC adapter, and do not pull or excessively bend the power cord.

■Never connect the power cord when your hands are wet.

■Do not connect the scanner to a multiplug power strip.

■Do not knot or coil the power cord, as this may result in a fire or electric shock. When connecting the power cord, make sure that the power plug is securely and completely inserted into the power outlet.

■Do not use power cords and AC adapters other than the power cord and AC adapter provided with this scanner.

■Never try to take the scanner apart or modify it in any way.

■Never try to take the AC adapter apart or modify it in any way, as this is dangerous and may lead to a fire or electric shock.

■Do not use flammable aerosol sprays near the scanner.

■When cleaning the scanner, turn the power OFF and disconnect the power cord from the power supply.

■Clean the scanner using a slightly dampened cloth which has been well wrung out. Never use alcohol, benzene, paint thinner, or any other flammable substances.

1-3

Chapter 1 Before Use

■If the scanner makes strange noises, or gives off, smoke, heat, or strange odors, or the scanner does not function or other abnormalities occur when you use the machine, immediately turn the power OFF, and disconnect the power plug from the power outlet. Then, contact your local authorized Canon dealer or service representative for further information.

■Do not drop the scanner, or subject it to impact or strong shock. Should the scanner ever become damaged, immediately turn the power OFF, and disconnect the power plug from the power outlet. Then, contact your local authorized Canon dealer or service representative to have the unit serviced.

■Before moving the scanner, make sure to turn the power OFF, and disconnect the power plug from the power outlet.

CAUTION

■Do not install the scanner on a surface that is unstable or tilted, or in an area subject to excessive vibrations, as this may cause the scanner to fall, resulting in personal injury or damage to the scanner.

■Do not block the ventilation openings. Doing so could cause the scanner to overheat, creating a risk of fire.

■Never place small metal objects such as staples, paper clips, or jewelry on the scanner. These items may fall into the scanner, and cause a fire or electric shock. Should such objects ever fall inside the scanner, immediately turn the power OFF, and disconnect the power plug from the power outlet. Then, contact your local authorized Canon dealer or service representative to have the unit serviced.

■Do not install the scanner in a humid or dusty location. Doing so may result in a fire or electric shock.

■Do not place objects on top of the scanner, as they may tip over and fall, resulting in personal injury.

■Do not use the scanner with a power supply voltage other than 120/220-240 VAC. Doing so might cause fire or electric shock.

■When disconnecting the power cord, grasp it firmly by its plug. Do not pull directly on the power cord, as this may damage or expose the cord’s internal wiring, resulting in a fire or electric shock.

■Leave sufficient space around the power plug so that it can be disconnected easily. If objects are placed around the power plug, you will be unable to disconnect it in an emergency.

■Do not allow water or flammable substances (alcohol, paint thinner, benzene, etc.) to spill into the scanner, as this may result in a fire or electric shock.

■Turn OFF the power for safety when not using the scanner for a long period of time, such as overnight. Also, turn OFF the power, and disconnect the AC adapter from the scanner and disconnect the power cord from the power outlet for safety when the machine will not be used for an extended period of time, such as during consecutive holidays.

■Do not wear loose clothing or jewelry that may get caught in the scanner while you are using it. This may result in personal injury. Be extra careful of neckties and long hair. If anything becomes caught in the scanner, immediately disconnect the power cord to stop the scanner.

■Be careful when placing paper in the scanner and when removing jammed paper. It is possible to cut your hand on the edge of a sheet of paper.

1-4

Chapter 1 Before Use

About the Fingerprint Sensor (ScanFront 300P only)

●The following actions may damage the sensor or cause it to malfunction:

–Dropping an object on the fingerprint sensor, or otherwise subjecting it to a strong impact

–Scratching the surface of the fingerprint sensor, or poking it with a pointed object

–Pressing a hard object such as a fingernail or metal item against the fingerprint sensor

–Touching the fingerprint sensor with dirty hands

–Placing a sticker on the surface of the fingerprint sensor, or covering the surface with ink or another substance

●If fingerprint authentication fails frequently, the fingerprint sensor may be dirty. Clean the surface of the fingerprint sensor regulary.

●When cleaning the fingerprint sensor, use a soft dry cloth to wipe dirt off the surface.

●Do not use a pointed object to remove any dirt that accumulates around the fingerprint sensor. Doing so may cause the fingerprint sensor to malfunction.

●Touching the fingerprint sensor while charged with static electricity may cause the fingerprint sensor or scanner unit to malfunction. Before touching the fingerprint sensor, discharge any static electricity by touching a piece of metal. Be especially careful during dry periods, such as the winter season, when the likelihood of being charged with static electricity is high.

Disposal

●Prior to disposing of the scanner, initialize the scanner to ensure that the registered data is deleted.

●When disposing of the scanner, make sure to follow all local ordinances and laws or consult with the retailer who sold you the scanner.

1-5

Chapter 1 Before Use

2. Features of the ScanFront 300/300P

The main features of the ScanFront 300/300P are described below.

ScanFront 300/300P

●Compact Network Document Scanner

The network document scanner has a compact design of 12.20" (W) × 8.66" (D) × 6.34" (H) (310 mm (W) × 220 mm (D) × 161 mm (H)). You can scan documents in a range of sizes from business cards to Legal/A4 size.

●Supports Transfer to a Variety of Destinations

You can transfer scanned image files to the following types of destinations via a network.

–Shared folders (excluding folders on a computer on a different segment of a network for which a WINS server is not configured)

–FTP Servers (excluding FTP servers that require firewall settings)

–E-mail addresses

–Fax (via an Internet fax service)

●ScanFront Service

By installing ScanFront Service on a computer on the network, you can also send scanned images to shared folders and devices, such as the following, for which direct transfer from the scanner is normally unavailable.

–Shared folders on a computer on a different segment of a network for which a WINS server is not configured

–Printers

●Variety of Scanning Modes

The scanner is equipped with five scanning modes: Black and White, Error Diffusion, Text Enhance, Gray, and Color.

●Long Document Scanning

The scanner is equipped with a scanning mode that can

automatically detect long document sizes.

*The available scanning modes vary depending on the file format of the image to be transferred.

●Fast Document Feeding

The scanner can scan a maximum of 30 Legal/A4 documents per minute.

*Scanning conditions: Black and white, simplex, 200 dpi

●Supports USB Memory

The scanner supports saving image files to USB memory to enable you to move them to destinations not connected to or not using a network.

●Touch Panel Operation

The 8.4-inch TFT SVGA (800 x 600 dots) screen with a touch panel enables you to perform all scanner operations by touching the screen.

●Configuration via the Web Menu

A web browser (Web Menu) is used for configuring the basic settings of the ScanFront, user registration, and job button registration.

*The Web Menu has an Administrator Mode for the administrator to configure settings and a User mode for users to register addresses and job buttons.

●ScanFront Administration Tool

By installing the supplied ScanFront Administration Tool software, you can simultaneously manage multiple ScanFront scanners on the network.

●Job Buttons

Pre-registering destinations and scan conditions as jobs enables you to scan by selecting a job button.

●Shared Address Book and Shared Job Button

The Shared Address Book and Shared Job Buttons are available for use by all users.

●My Address Book and My Job Button

In addition to the address book and job buttons shared by all users, a My Address Book and My Job Button are available for each user.

1-6

Chapter 1 Before Use

●Supports Mouse and Keyboard

In addition to touch-panel operation, you can also use a mouse and keyboard to operate the scanner. (See

p. 2-5.)

●Supports Directory Services

The scanner supports directory services (Active Directory and OpenLDAP), which enables you to reference and use user accounts and e-mail addresses registered on a domain server and LDAP server.

●Functional Restrictions

The scanner enables you to restrict, for example, the destinations and Home screen available to each user.

●Auto Size Detection

The scanner can detect the size of a scanned document and erase the white space around the image.

●Auto Color Detection

The scanner can automatically detect whether a document is color or black and white, and save the scanned images accordingly.

●Folio Scanning

The scanner can scan both sides of a document folded in half and create a single scanned image.

●Text Enhance Mode

The background color of the text are processed to

enhance the text portions and make them easy to read.

*This function may not work effectively for some documents.

●Double Feed Detection by Length

When the scanner detects a double feed by comparing the lengths of documents, it stops feeding.

*Using the length of the first document as a reference, the scanner detects a double feed when a document of a different length is fed.

●Skip Blank Page Function

The scanner scans both sides of a document and skips saving the image of any side it determines to be a blank page.

●Deskew

If the scanner detects from a scanned image that the document was fed askew, the image is straightened.

●Image Rotation

The scanner can rotate a scanned image in 90° increments, or detect the text orientation within the document, and then rotate the image in 90° increments so that the orientation of the text is correct.

●Eliminates Bleed-Through

The scanner prevents the images on the reverse side of thin documents from appearing on the scanned pages.

●Dropout and Color Enhancement Functions

The scanner is equipped with a dropout function that allows you to specify one color (red, blue, or green) to omit, and a function to enhance a specified color when scanning.

●Card Scanning

You can scan credit cards and IC cards that conform to ISO standards.

●Prescan

This function prescans the first page of a document at the start of scanning, and then stops scanning so that you can view the results to adjust the brightness and contrast before scanning the entire document.

ScanFront 300P

●Fingerprint Authentication

The authentication system that uses a fingerprint sensor to authenticate users enables you to log in to the ScanFront 300P without entering your user name and password.

●Double Feed Detection by Ultrasonic Function

In addition to the double feed detection function that compares the lengths of documents, the scanner is equipped with a double feed detection function that uses an ultrasonic sensor.

1-7

Chapter 1 Before Use

3. Names and Functions of Parts

The names and functions of the parts of the ScanFront 300/300P are shown below.

Front and Document Feed and Eject Trays

aTray Extension

Open this to prevent scanned documents from slipping off.

bDocument Eject Tray

Open this tray when using the ScanFront. If scanned documents curl in the document eject tray, remove the entire tray. (See p. 2-4.)

c Panel Unit

dTouch Panel

Touch this screen to operate the ScanFront.

eLock Lever

Locks the panel unit. Pull the lever toward you to unlock the panel unit. (See p. 2-10.)

fDocument Guides

Adjust these to match the width of the document. (See p. 2-6.)

gDocument Feed Tray

Place documents here. (See p. 2-4.)

hUSB Port (Front)

Connect a USB1.1/Hi-Speed USB2.0 compatible USB memory device, USB keyboard, or USB mouse.

iPower Switch

Use this to turn the power ON. (See p. 3-4.)

*Use the Power OFF button on the touch panel to turn the power OFF.

jFeed Selection Lever

Use this lever to change the feed method for documents. (See p. 2-5.)

kPower Indicator

Lights when the power is ON. (See p. 3-4.)

lFingerprint Authentication Sensor (Only Available with the ScanFront 300P)

This fingerprint sensor is for fingerprint registration and authentication. (See p. 2-11.)

Open this when there is a paper jam or to perform maintenance. (See p. 2-10.)

1-8

Chapter 1 Before Use

Side and Rear

mUSB Port (Rear Left)

Connect a USB1.1/Hi-Speed USB2.0 compatible USB memory device, USB keyboard, or USB mouse.

nPower Connector (24 VDC)

Connect the plug of the supplied AC adapter. (See p. 3-3.)

oKensington Slot

This is an anti-theft slot that enables a key chain or lock to be connected to prevent theft.

pService Switch

This is a service switch. Do not insert any object into this hole.

qLAN Port (RJ-45)

Connect an RJ-45 (10Base-T/100Base-TX) compatible network cable. (See p. 3-3.)

rUSB Ports (Rear Right)

Connect a USB1.1/Hi-Speed USB2.0 compatible USB memory device, USB keyboard, or USB mouse.

s Ventilation Holes

1-9

Chapter 1 Before Use

4. Network Environment

The network environment required to use the ScanFront is described below. To obtain details on your network environment, contact your network administrator.

Network Environment

●Microsoft Windows Network

Use the scanner in a Microsoft Windows Network environment.

●Network Protocol

The scanner uses TCP/IP protocol to connect to the network.

●IP Address Assignment

The TCP/IP protocol uses one IP address for each device connected to the network. Consult your network administrator to determine the IP address to assign to the scanner.

●DHCP Support

The scanner supports DHCP (Dynamic Host Configuration Protocol). A DHCP server provides a network environment in which IP addresses can be obtained automatically from the DHCP server, so there is no need to set an IP address for the scanner.

*The number of IP addresses that can be obtained using DHCP is managed by the network administrator. For details, consult your network administrator.

●100Base-TX Support

The scanner supports 100Base-TX. However, communication may be slower than the communication speed of the network, depending on the other devices connected to the network and the type of hub.

●SMTP (E-mail) Server

The scanner supports an SMTP server, so you can send image files directly from the scanner by e-mail.

●FTP Server

The FTP server function supports an FTP server configured within the local network, and is unable to send to an FTP server that requires firewall settings.

●Fax

Scanned images can be sent to specified addresses as fax documents by sending e-mails that include the scanned images as attachments to an Internet fax service. Therefore, you must specify message formats and addresses in the method prescribed by your Internet fax service.

●Printer

By specifying a printer connected to the same network as the ScanFront as the destination, you can print scanned images. In such cases, a computer on which ScanFront Service is installed must exist on the same network as the ScanFront scanner.

Directory Service Support

●Active Directory

Active Directory is a directory service adopted by Windows 2000, and information registered to Active Directory can be used on other computers. The ScanFront allows user information registered to the domain server registered as the authentication server to be used for authentication to log in to the ScanFront.

*A domain server that uses Windows NT Server for the operating system cannot be registered as an authentication server.

●OpenLDAP Server

The scanner supports OpenLDAP servers that can be connected to with the LDAP (Lightweight Directory Access Protocol) protocol.

You can authenticate ScanFront users and reference e- mail addresses for registration to the address book using the user information registered on the OpenLDAP server.

1-10

Chapter 1 Before Use

Limitations

●Limitations in Browsing for Shared Folders

A problem in browsing for shared folders on computers running the Windows 7 or Windows Server 2008 R2 operating system has been determined to exist. You will not be able to browse for shared folders to act as image file destinations by pressing the [Browse] button on the ScanFront touch panel. (Similarly, you will not be able to browse for shared folders in the screen that appears after you click [Browse] in the ScanFront Web Menu.) This problem is due to the specifications of Windows 7 and Windows Server 2008 R2.

As a result, if you want to specify a shared folder on a computer running these operating systems as the destination for image files, you must enter the shared folder manually. (When operating the ScanFront touch panel to specify a shared folder as the destination address, for example, enter the folder path in [Folder path].) Instead of entering the full path in such cases, you can press the [Browse] button after entering the computer name and the path up until the top-most folder of that computer, and then specify the rest of the path in the screen that appears.

This problem does not occur when the supplied ScanFront Service software is installed on the network.

●Limitations for Network Environments without ScanFront Service

To send image files to destinations and devices, such as the following, the supplied ScanFront Service software must be installed on a computer on the same network as the ScanFront scanner.

–Destinations (folders on computers, printers, etc.) located on different segments of a network on which a WINS server is not configured

–Printers on the network

–Certain NAS (network-attached storage)

1-11

Chapter 2 Handling

1.	Documents.......................................................	2-2
	Plain Paper............................................................	2-2
	Business Card.......................................................	2-2
	Card ......................................................................	2-3
2.	Preparing the Scanner.....................................	2-4
	Preparing the Document Feed Tray and
	Eject Tray ..............................................................	2-4
	Feed Selection Lever ............................................	2-5
	USB Port ...............................................................	2-5
3.	Placing Documents..........................................	2-6
	Placing a Document ..............................................	2-6
	Placing a Folded Document ..................................	2-7
	Placing a Long Document .....................................	2-7
	Placing a Card.......................................................	2-8
4.	Clearing a Paper Jam or Double Feed Error ...	2-9
5.	Fingerprint Sensor (ScanFront 300P)............	2-11
	Cautions for Handling the Fingerprint Sensor .....	2-11
	Fingerprint Authentication ...................................	2-12

Chapter 2 Handling

1. Documents

The ScanFront can scan documents in a range of sizes from business cards to Legal/A4.

It is possible to feed documents of the following sizes and thicknesses depending on the feeding method used.

Plain Paper

Size

Width: 2" to 8 1/2" (50.8 mm to 216 mm) Length: 2 1/8" to 14" (53.9 mm to 355.6 mm)

(up to 39.3" (1,000 mm) in Long Document mode)

Thickness for Page Separation ON

14 lb to 57 lb bond (52 g/m2 to 209 g/m2)

Thickness for Page Separation OFF

11 lb to 57 lb bond (40 g/m2 to 209 g/m2)

IMPORTANT

A document must meet the following criteria to be scannable:

•When scanning a multipage document, pages must be grouped together so that they have the same size, thickness, and weight. Scanning different types of paper at one time can cause the scanner to jam.

•Always make sure that the ink on a document is dry before scanning it. Scanning documents with the ink still wet may soil the rollers or scanning glass, cause lines or smudges to appear on images, or dirty other documents.

•Always clean the rollers or scanning glass after scanning a document written in pencil. Scanning documents with pencil written on them may soil the rollers or scanning glass, cause stripes to appear in images, or dirty other documents.

•When scanning a two-sided document that is printed on thin paper, the image on the opposite side of each page may show through. Adjust the brightness in the scanning conditions before scanning the document.

•Note that scanning the following types of documents can cause a paper jam or malfunction. To scan such a document, make a photocopy of the document and then scan the photocopy.

Wrinkled or creased

Carbon paper

documents

			Curled documents		Coated paper
			Torn documents		Extremely thin,
					translucent paper
			Documents with		Document with square
			paper clips or staples		punch holes

Business Card

Size

Width: 2" (50.8 mm) and above

Length: 2 1/8" (53.9 mm) and above

Thickness

82 lb Cover (300 g/m2) and below

IMPORTANT

•If the stack of business cards that you placed is not fed properly, reduce the number business cards.

•Business cards may sometimes be stacked in the wrong order when they are ejected, depending on the size and thickness of the business cards, and the orientation that they are loaded.

2-2

Chapter 2 Handling

Card

Size

2.12" × 3.37" (53.9 × 85.5 mm) (Conforming to ISO

Standards)

Thickness

0.0299" (0.76 mm) and below

Insertion orientation

Landscape

IMPORTANT

•Insert cards one at a time.

•Be careful when inserting cards to avoid damaging them.

2-3

Chapter 2 Handling

2. Preparing the Scanner

When placing a document in the scanner, pull out the document eject tray so that it matches the size of the document, and then move the feed selection lever to the appropriate position for the desired feed method (Page Separation ON or OFF) for the document.

Preparing the Document Feed Tray and Eject Tray

Prepare the trays in accordance with the type of document.

1.Open the document feed tray a.

2.Open the document eject tray b.

Hint

If the output documents curl in the eject tray when scanning particularly thin documents, remove the eject tray.

To remove the document eject tray, push in on the illustrated portions of the tray on both sides in the direction of the arrows a and pull out b.

	Hint	To reattach the eject tray, insert the protrusions on both sides of
	Open the center tray extension when output documents are
		the tray into the holes on the scanner.
	likely to fall out of the tray.

After connecting the tray, make sure that it is attached securely.

2-4

Chapter 2 Handling

Feed Selection Lever

Change the position of the lever to the desired feed method for the document.

Page Separation ON

Move the lever downward to separate a stack of documents one page at a time in order to continuously feed the documents.

Page Separation OFF

Move the lever upward to feed a document with multiple pages attached together such as an invoice one page at a time without separating the pages.

Page Separation

ON

Page Separation

OFF

Feed selection lever

IMPORTANT

Moving the lever upward (Page Separation OFF) and then scanning a stack of documents will cause multiple pages to be fed at the same time.

USB Port

You can insert a USB memory device to store image files.

USB Memory

You can also connect a USB keyboard and USB mouse to operate the ScanFront.

IMPORTANT

•The scanner will not start if you turn the power ON while a USB memory device is inserted. Insert the USB memory device after the scanner has started up.

•Use USB memory that is not write-protected. If the USB memory is write-protected, data cannot be written to the USB memory.

•This scanner does not support USB memory equipped with password security, data encryption, or functions other than data storage.

•Make sure that the USB memory has sufficient space to store images.

2-5

Chapter 2 Handling

3. Placing Documents

When placing documents into the scanner, place them face down into the tray with the top edge of the document at the bottom of tray.

Placing a Document

Follow the procedure below to place a document.

1.Adjust the document guides to be wider than the width of the document.

2.Fan the document to offset the pages so that the top edge of the first page is the lowest.

3.Place the document face down with its top edge at the bottom of the tray.

4.Adjust the document guides to fit the width of the document.

2-6

Chapter 2 Handling

IMPORTANT

Make sure that document stacks placed in the feed tray do not exceed the document guides.

Loading mark

The number of sheets that you can place in the scanner at one time varies by paper size as follows.

Legal/A4 Size or Smaller:

50 sheets (stack 5 mm thick) or less

Sizes Larger than Legal/A4:

30 sheets (stacks 3 mm thick) or less

Placing a Folded Document

Folio Scan enables you to scan documents that are larger than Legal/A4 and therefore do not fit in the feeder. (The maximum size is 11" X 17"/A3.) To use the function, fold the document in half lengthwise and place it into the feeder. The ScanFront 300/300P will scan both sides and combine the scanned images into a single image.

IMPORTANT

•When folding the document, align the right and left sides and create a sharp, straight fold. Otherwise the document may jam or the image may not be aligned properly.

•The fold line itself will not be scanned. Keep this in mind if there is content such as photos, diagrams, or text that spans the fold.

•For Folio scanning, only the Page Separation OFF mode can be used. Place documents one at a time.

•Adjust the document guides to fit the width of the document. Otherwise, the image may scan as skewed or shifted.

Hint

•When scanning folded documents, switch the feed selection lever to OFF. (See p. 2-5.)

•When placing folded documents, place the document into the scanner so that the fold is on the right side. The side of the folded document facing you will become the right side of the combined image.

•When scanning a document that is folded in half, set [Scanning Side] to [Folio].

•The maximum size for combined images is A3. When scanning a folded document of a size other than the standard formats, set [Page Size] to [Auto size].

•When scanning a document that is folded in half, set [Resolution (dpi)] to 300 dpi or less.

•When scanning a document that is folded in half, the [Double feed detection by Ultrasonic] function cannot be used.

Placing a Long Document

You scan documents up to 39.3" (1,000 mm) in length.

IMPORTANT

•When scanning a long document, set [Page Size] to [Auto size (Long)].

•When scanning a long document, set [Resolution (dpi)] to 200 dpi or less.

•You cannot set [Scanning Side] to [Folio] when scanning a long document.

2-7

Chapter 2 Handling

Placing a Card

When you want to scan a card, follow the procedure below to place the card.

1. Move the feed selection lever upward (OFF).

IMPORTANT

When scanning cards, set the feed selection lever to OFF and make sure to scan the cards one at a time.

2.Adjust the document guides to match the width of the card.

3.Place the card face down with the top edge at the bottom of the tray.

CAUTION

•A card placed into the document feed tray in the portrait orientation may not be output properly because a load is placed on it during feeding. Furthermore, removing a card that has caused a feeding error may damage the card, so make sure to correctly insert the card.

•Pull the lock lever and open the panel unit before removing a placed card. Inserting a finger into the scanner while the panel unit is closed may result in an injury.

Lock lever

2-8