Canon LV-7255 User Manual

0 (0)

MULTIMEDIA PROJECTOR

LV-7255

User’s Manual

E

English

Important Information

Safety Cautions

Precautions

Please read this manual carefully before using your Canon LV-7255 projector and keep the manual handy for future reference. Your serial number is located on the bottom of your projector. Record it here:

CAUTION

To turn off main power, be sure to remove the plug from power outlet.

The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.

This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided.

The information should be read carefully to avoid problems.

WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS CAN BE FULLY INSERTED.

DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED SERVICE PERSONNEL.

Acoustic Noise Information Ordinance-3. GSGV (for Germany only):

The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.

CAUTION

Avoid displaying stationary images for a prolonged period of time.

Doing so can result in these images being temporarily sustained on the surface of the LCD panel.

If this should happen, continue to use your projector. The static background from previous images will disappear.

CAUTION

Do not put the projector on its side when the lamp is turned on.

Doing so may cause damage to the projector.

WARNING TO CALIFORNIA RESIDENTS:

Handling the cables supplied with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

i

Important Information

NOTE FOR CUSTOMERS IN THE US

Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.

Federal Communication Commission Notice

Multimedia Projector, Model : LV-7255

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

The cable with the ferrite core provided with the projector must be used with this equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Canon U.S.A., Inc.

One Canon Plaza, Lake Success, NY 11042, U.S.A.

Tel No. (516)328-5600

Canadian Radio Interference Regulations

This Class B digital apparatus complies with Canadian ICES-003.

Réglementation canadienne sur les intérferences radio

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

European Union (and EEA) only.

This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC) and your national law.This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.

Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources and will avoid incurring administrative sanctions according to art.

50 and following of Italian legislative decree 22/97.

For more information regarding return and recycling of WEEE products, please visit www.canon-europe.com/environment.

(EEA: Norway, Iceland and Liechtenstein)

ii

Important Information

LAMP HANDLING

PRECAUTIONS

This projector uses a high-pressure mercury lamp which must be handled carefully and properly as mentioned below.

A lamp may explode with a loud sound or burn out due to a shock, scratch, or expiration of lifetime.

The lamp life may differ from lamp to lamp and according to the environment of use. There is not guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their life in a shorter period of time than other similar lamps.

A lamp gradually becomes darker with time of use.

If the projector indicates that the lamp should be replaced (i.e., the LAMP indicator blinks red rapidly), chances of explosion become higher. Replace the lamp with a new one immediately.

Always keep your face away from the exhaust vent so that you do not suffer from the gas and broken shards of the lamp.

IF A LAMP EXPLODES

If a lamp explodes, the gas and broken shards may scatter inside the projector and they may come out of the exhaust vent. The gas contains toxic mercury.

Open windows and doors for ventilation.

If you inhale the gas or the shards of the broken lamp enter your eyes or mouth, consult the doctor immediately.

If a lamp explodes, its shards may scatter inside the projector. Ask the Canon service representative to clean and check the inside of the projector and replace the lamp.

DISPOSAL OF WASTE LAMP

Dispose of the mercury lamp of the projector according to the local regulation just like the fluorescent lamp.

Lamp Replacement

To replace the lamp, follow all instructions provided on page 50.

Be sure to replace the lamp when the message [Replace with the new lamp.] appears. If you continue to use the lamp after the lamp has reached the end of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury.

If this happens, contact your dealer for lamp replacement.

CAUTION

When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass fragments could fall if the lamp has been burned out.

iii

Important Information

For UK only: In UK, a BS approved power cord with moulded plug has a Black (five Amps) fuse installed for use with this equipment. If a power cord is not supplied with this equipment please contact your supplier.

Important Safeguards

These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings.

Installation

Do not place the projector in the following conditions:

-on an unstable cart, stand, or table.

-near water, baths or damp rooms.

-in direct sunlight, near heaters or heat radiating appliances.

-in a dusty, smoky or steamy environment.

-on a sheet of paper or cloth, rugs or carpets.

If you wish to have the projector installed on the ceiling:

-Do not attempt to install the projector yourself.

-The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury.

-In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes.

-Please consult your dealer for more information.

Do Not Use in the Following Environments

Do not install the projector in a humid or dusty place or a place where there is much oily smoke or cigarette smoke. Optical parts such as a lens and mirror are stained, resulting in poor picture.

Do not use the projector in a place where the temperature becomes very high or low.

Operating temperature: +5°C to +35°C Storage temperature: -10°C to +50°C

Place the projector in a horizontal position

The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.

10˚

Fire and Shock Precautions

Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside projector. Allow at least 1 m (3.3') of space between your projector and a wall.

Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated the projector is turned on and immediately after the projector is turned off.

Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your project. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified service personnel.

Do not place any objects on top of the projector.

Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.

The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power fits this requirement before attempting to use your projector.

iv

Important Information

Do not look into the lens while the projector is on. Serious damage to your eyes could result.

Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause unpredictable outcome such as fire or injury to the eyes.

Do not cover the lens with the black lens cap or equivalent while the projector is on. Doing so can lead to melting the cap and possibly burning your hands due to the heat emitted from the light output.

Do not place any objects, which are easily affected by heat, in front of the projector lens or a projector exhaust

Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the output and exhaust.

Handle the power cable carefully. A damaged or frayed power cable can cause electric shock or fire.

-Do not use any power cables than the supplied one.

-Do not bend or tug the power cable excessively.

-Do not place the power cable under the projector, or any heavy object.

-Do not cover the power cable with other soft materials such as rugs.

-Do not heat the power cable

-Do not handle the power plug with wet hands.

Turn off the projector, unplug the power cable and have the object removed by a qualified service personnel under the following conditions:

-When the power cable or plug is damaged or frayed.

-If liquid has been spilled into the projector, or if it has been exposed to rain or water.

-If the projector does not operate normally when you follow the instructions described in this user's manual.

-If the projector has been dropped or the cabinet has been damaged.

-If the projector exhibits a distinct change in performance, indicating a need for service.

-If the projector is not to be used for an extended period of time.

Disconnect the power cable and any other cables before carrying the projector

Turn off the projector and unplug the power cable before cleaning the cabinet or replacing the lamp.

CAUTION

Do not try to touch the ventilation outlet on the left side (when seen from the front) as it can become heated while the projector is turned on.

Do no use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or hanging on the wall can cause damage to the projector.

Select [High] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select [Advanced settings] → [Fan mode] → [High].) Fan noise increases noticeably in High mode.

Select [High] in Fan mode if you use the projector at a high altitude or under low atmospheric pressure.

Do not unplug the power cord from the wall outlet under any one of the following circumstances. Doing so can cause damage to the projector:

*While the Hour Glass icon appears.

*While the cooling fans are running. (The cooling fans continue to work for 30 seconds after the projector is turned off).

*While the lamp is lighted.

CARRYING/TRANSPORTING THE PROJECTOR

This projector is a precision machine. Do not give a strong shock to the projector or turn it down.

Thoroughly read "Use Caution When Carrying or Transporting the Projector" below and install the lens cap before carrying the projector. When transporting the projector by train or airplane, use a highly crashworthy transport case.

Use Caution When Carrying or Transporting the Projector

The carrying bag is intended for protection from dust and scratches on the surface of the cabinet, and it is not designed to protect the projector from external shocks. When carrying the projector with it put in the carrying bag, do not give a shock to it, drop it, or place anything on it.

Do not transport the projector through a courier or transport service with the carrying bag. The projector can damage.

v

Important Information

Remote Control Precautions

Handle the remote control carefully.

If the remote control gets wet, wipe it dry immediately.

Avoid excessive heat and humidity.

Do not heat, take apart, or throw batteries into fire.

If you will not be using the remote control for a long time, remove the batteries.

Ensure that you have the batteries' polarity (+/-) aligned correctly.

Do not use new and old batteries together, or use different types of batteries together.

Dispose of used batteries according to your local regulations.

vi

Table of Contents

Important Information ...........................................................................

i

1. Introduction ......................................................................................

1

What's in the Box? ........................................................................................................

1

Introduction to the Projector .........................................................................................

2

Part Names of the Projector .........................................................................................

4

Top Features ...........................................................................................................

6

Terminal Panel Features .........................................................................................

7

Part Names of the Remote Control ..............................................................................

8

Battery Installation ...........................................................................................

10

Remote Control Precautions ............................................................................

10

Operating Range for Wireless Remote Control ................................................

10

2. Installation and Connections .......................................................

11

Setting Up the Screen and the Projector ....................................................................

12

Selecting a Location ..............................................................................................

12

Throw Distance and Screen Size ..........................................................................

12

Making Connections ...................................................................................................

14

Enabling the computer’s external display ..............................................................

14

Connecting Your PC or Macintosh Computer ........................................................

14

To connect Scart output (RGB) .............................................................................

15

Connecting an External Monitor ...........................................................................

16

Connecting Your DVD Player with Component Output ..........................................

17

Connecting Your VCR or Laser Disc Player ..........................................................

18

Connecting the Supplied Power Cord ...................................................................

19

3. Projecting an Image (Basic Operation)......................................

20

Turning on the Projector .............................................................................................

20

Note on Startup Screen (Menu Language Select screen) ....................................

21

Selecting a Source .....................................................................................................

22

Adjusting the Picture Size and Position ......................................................................

23

Correcting Keystone Distortion ...................................................................................

25

Automatically Optimizing on RGB Image ...................................................................

27

Turning Up or Down Volume .......................................................................................

27

Turning off the Projector .............................................................................................

28

After Use .....................................................................................................................

28

vii

 

Table of Contents

4. Convenient Features ......................................................................

29

Turning Off the Image and Sound ...............................................................................

29

Freezing a Picture.......................................................................................................

29

Enlarging and Moving a Picture ..................................................................................

29

Using the Remote Mouse Receiver ............................................................................

30

Preventing the Unauthorized Use of the Projector .....................................................

32

5. Using On-Screen Menu .................................................................

34

Using the Menus .........................................................................................................

34

Menu Elements ...........................................................................................................

36

List of Menu Items ......................................................................................................

37

Menu Descriptions & Functions [Image adjustment] ..................................................

39

Menu Descriptions & Functions [Display settings] ......................................................

41

Menu Descriptions & Functions [Setup] .....................................................................

42

Menu Descriptions & Functions [Advanced settings] .................................................

44

Menu Descriptions & Functions [Information] .............................................................

46

Menu Descriptions & Functions [Factory default] .......................................................

47

6. Maintenance ....................................................................................

48

Cleaning or Replacing the Filter ................................................................................

48

Cleaning the Cabinet and the Lens ...........................................................................

49

Replacing the Lamp ...................................................................................................

50

7. Appendix ...........................................................................................

53

Troubleshooting .........................................................................................................

53

Specifications ............................................................................................................

56

Cabinet Dimensions ..................................................................................................

58

Pin Assignments of D-Sub ANALOG Input Connector ..............................................

59

Compatible Input Signal List ......................................................................................

60

Relationship between Screen Size and Projection Distance ......................................

61

PC Control Codes and Cable Connection .................................................................

62

Troubleshooting Check List ........................................................................................

63

viii

1. Introduction

What's in the Box?

Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your projector.

Projector

CKBA

+

M

-

CP

O

TUA

TUPIN

E

WO P

ARNINGW

PMLA

Lens cap

AC power cord

VGA cable

(4.5 m / 14.8’)

(1.8 m / 5.9’)

 

[7N520052]

Soft case

 

 

POWER

 

 

 

 

ASPECT

IMAGE

 

IN

FO.

 

INPUT

 

MENU

 

 

AUTO

PC

 

 

 

N

 

 

 

 

O SH

 

 

 

 

 

OW

 

 

 

 

 

L-

 

 

 

CLICK

 

 

VOL

R-

BACK

 

P

CLICK

FREEZE

AGE

 

 

 

D.

 

 

 

ZOOM

 

RD428E

Remote control Batteries (AAA 2)

 

Quick

Start

Guide

 

Important

Information

Quick Start Guide

CD-ROM

Warranty

Important Information

User’s manual

 

Remote mouse receiver (10 cm / 0.3’) [7N900562]

1

1. Introduction

Introduction to the Projector

This section introduces you to your new projector and describes the features and controls.

Congratulations on Your Purchase of The Projector

The LV-7255 is one of the very best projectors available today. The projector enables you to project precise images up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, DVD player, document camera, or a laser disc player.

You can use the projector on a tabletop or cart, from behind a screen, or permanently mounted on a ceiling*1. The remote control can be used wirelessly.

*1 Do not attempt to mount the projector on a ceiling yourself.

The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury.

In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes. Please consult your dealer for more information.

Features you'll enjoy:

Auto vertical keystone correction

Built-in Screen color presets provide for adaptive color correction when projecting onto non-white screen material

Quick Start & Quick Shutoff

The quick start & quick shutoff function means you can set up or put away the projector without delay. Nine seconds after turning on the power, the projector is ready to display PC or video images.

When you're finished, the fans stop in 30 seconds after turning off the power, so you can put away the projector quickly after the conference or class.

Low level operation noise

Short focal length lens

200W lamp (150W Quiet mode)

Direct keys for source selection

New Color Management system

New menu design improves operation

Safety protect by Password function

Password feature prevents the projector from being used by unauthorized individuals. Password prevents unauthorized individuals from changing projector settings or adjustments.

You can use the supplied wireless remote control and remote mouse receiver to operate your PC mouse

wireless from across the room. The remote mouse receiver supports almost any PC using a USB connection.

You can control the projector with a PC or control system using the PC Control port.

The contemporary cabinet design is light, compact, easy to carry, and complements any office, boardroom or auditorium.

2

1. Introduction

About this user's manual

The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find an overview. If the section doesn't apply, you can skip it.

IBM is a trademark or registered trademark of International Business Machines Corporation.

Mac and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

Windows, Windows 98, Windows Me, Windows XP or Windows 2000 are trademarks or registered trademarks of Microsoft Corporation.

Other product and company names mentioned in this user’s manual may be the trademarks or registered trademarks of their respective holders.

3

1. Introduction

Part Names of the Projector

Front/Top

Zoom Lever

 

 

 

Controls

 

 

 

(See page 24)

 

 

 

(See page 6)

Focus Ring (See page 24)

Remote sensor (See page 10)

Lens

Adjustable Tilt Foot Lock Button (See page 23)

Adjustable Tilt Foot (See page 23)

KCAB

LOV+

M

LOV-

 

 

 

PC TO

T

INPU

UA

 

 

R

E

WOP

NGI

RNAW

PMLA

Ventilation (inlet) / Filter Cover (See page 48)

Do not block this vent. Troubles or fire can result.

Ventilation (inlet)

Lens Cap

Be sure to remove the lens cap during projection. The cap can deform or fire can occur.

*This security slot supports the MicroSaver ® Security System. MicroSaver ® is a registered trademark of Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.

Rear

Monaural Speaker

(1W)

Terminal Panel

(See page 7)

WARNING

POWER

LAMP

INPUT

AUTO PC

-VOL

 

 

 

 

 

 

 

 

 

 

 

+VOL

VIDEO

 

 

 

 

 

 

 

 

 

 

 

IN

L

AUD

 

 

 

 

 

 

 

 

BACK

 

 

IO IN

R

 

 

 

 

 

 

 

S-

 

 

 

 

 

 

 

 

 

 

VIDEO

MONO

 

 

 

 

 

 

 

 

 

IN

 

 

 

 

 

 

 

 

 

 

L

AUD

 

 

 

 

 

 

 

 

 

 

 

IO IN

R

 

 

ANA

 

 

 

 

 

 

 

 

AUDIO

 

LOG

IN-1

 

 

 

 

 

MONO

 

OUT

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO IN

 

 

 

 

 

 

 

 

 

 

SERVICE

 

ANA

LOG

 

 

 

 

 

 

 

 

 

 

IN-2

 

 

 

 

 

 

 

 

PORT

 

 

 

MENU

Remote sensor (See page 10)

Ventilation (outlet)

Heated air is exhausted from here.

Do not block this vent. Troubles or fire can result.

Built-in Security Slot (

 

)*

AC Input

 

 

 

 

Connect the supplied power cord’s two-pin plug here, and

 

 

 

plug the other end into an active wall outlet. (See page 19)

Main Power Switch

When you plug the supplied power cord into an active wall outlet and turn on the Main Power, the POWER indicator turns orange and the projector is in standby mode.

(See page 20)

4

1. Introduction

Bottom

Lamp Cover

(See page 50)

Adjustable Tilt Foot (See page 23)

Adjustable Tilt Foot Lock Button

(See page 23)

NOTE: A spacer is attached to the rear foot at the factory.

To fine-adjust the height of the rear foot, remove the spacer and rotate the rear foot to the desired height. Do not throw away or lose the spacer.

HINT: The Canon logo is on the panel of the projector cabinet . When projecting an image with the projector hung from the ceiling, turn the Canon logo upside down.

To turn the logo upside down, follow the steps below.

1. Push one end of the logo gently.

The other end will pop up slightly.

• The right drawing shows the part “C” is pressed gently.

• The part “n” on the other end will pop up.

2. Push and hold the end of the logo gently and rotate the logo by holding the other end.

• The right drawing shows that with the part “C” pressed the logo is rotated by holding the part “n” on the other end.

3. Release your hold and turn the logo upside down.

5

1. Introduction

Top Features

3

WARNING

O

W

 

E

P

 

R

LAMP

4

1 2

7

5 8

MENU

INPUT

 

AUTO PC

 

VOL

VOL

-

+

BACK

6 9 10

1.POWER Button ( )

Use this button to turn the power on and off when the main power is supplied and the projector is in standby mode.

To turn on the projector, press and hold this button for about 1 second. To turn off the projector, press this button twice.

2.POWER Indicator

Detecting the Signal Automatically

Press and hold the INPUT button for a minimum of 2 seconds, the projector will search for the next available input source. Each time you press and hold the INPUT button for a minimum of 2 seconds, the input source will change as follows:

Computer 1 → Computer 2 → Video → S-Video → Computer1 → ...

When this indicator is green, the projector is on; when this indicator is orange, it is in standby mode. See the Power Indicator section on page 53 for more details.

3.WARNING Indicator

If this light blinks red rapidly, it indicates that an error has occurred, the lamp cover is not attached properly or the projector has overheated. If this light remains orange, it indicates that you have pressed a cabinet key while the Key lock is enabled. See the WARNING Indicator section on page 53 for more details.

4.LAMP Indicator

If this light blinks red rapidly, it's warning you that the lamp has reached the end of its usable life. After this light appears, replace the lamp as soon as possible (See page 50). If this is lit green continually, it indicates that the lamp mode is set to Quiet. See the Lamp Indicator section on page 53 for more details.

5.INPUT Button

Selecting from INPUT List

Press and quickly release the INPUT button to display the INPUT list. Each time the INPUT button is pressed, the input source will change as follows: "Computer 1", "Computer 2", "Video" (VCR or laser disc player), "S-Video", To display the selected source, press the OK button or allow 2 seconds to elapse.

6.AUTO PC Button

Use this button to adjust an RGB source for an optimal picture (See page 27).

7.MENU Button

Displays the menu.

8.SELECT / VOL (+/–) Buttons

: Use these buttons to select the menu of the item you wish to adjust.

: Use these buttons to change the level of a selected menu item. A press of the button executes the selection. When no menus appear, these buttons work as a volume control.

9.OK Button

Executes your menu selection and activates items selected from the menu.

10.BACK Button

Pressing this button will return to the previous menu. While you are in the main menu, pressing this button will close the menu.

6

1. Introduction

Terminal Panel Features

 

4

 

 

1

 

VIDEO

L AUDIO IN R

 

ANALOG IN-1

AUDIO IN

ANALOG IN-2

IN

 

 

 

 

 

S-VIDEO

MONO

AUDIO OUT

 

SERVICE PORT

 

L AUDIO IN R

 

 

IN

 

 

 

 

 

MONO

 

 

 

 

3 2

1.ANALOG IN-1 and -2 / Component Input Connector (Mini D-Sub 15 Pin)

Connect your computer or other analog RGB equipment such as IBM compatible or Macintosh computers. Use the supplied RGB cable to connect to your computer.This also serves as a component input connector that allows you to connect a component video output of component equipment such as a DVD player. This connector also supports Scart output signal. See page 15 for more details.

AUDIO IN Mini Jack (Stereo Mini)

This is where you connect the audio output from your computer or DVD player when connected to the COMPUTER input. A commercially available audio cable is required.

2.MONITOR OUT Connector (Mini D-Sub 15 Pin)

You can use this connector to loop your computer image to an external monitor from the RGB input source.

This connector outputs RGB signal in standby mode.

AUDIO OUT Mini Jack (Stereo Mini)

You can use this jack to output sound from the currently selected source (COMPUTER, VIDEO or S- VIDEO). Output sound level can be adjusted in accordance with the sound level of the internal speaker.

Note that this cannot be used as a headphone jack.

(When audio equipment is connected, the projector speaker is disabled.)

When a cable mini-plug is inserted into this jack, both the right and left audio signals are not mixed, but separate.

5

For example, when a cable mini-plug is inserted into the left AUDIO IN jack only, only left sound is output.

3.S-VIDEO IN Connector (Mini DIN 4 Pin)

Here is where you connect the S-Video input from an external source like a VCR.

NOTE: S-Video provides more vivid color and higher resolution than the traditional composite video format.

S-VIDEO AUDIO Input Jacks L/R (RCA)

These are your left and right channel audio inputs for stereo sound from an S-Video source.

4.VIDEO IN Connector (RCA)

Connect a VCR, DVD player, laser disc player, or document camera here to project video.

VIDEO AUDIO Input Jacks L/R (RCA)

These are your left and right channel audio inputs for stereo sound from a Video source.

5.SERVICE PORT (Mini DIN 8 Pin)

Use this port to connect a PC or control system to control the projector via an optional RS-232C serial cable (LV-CA34). If you are writing your own program, typical PC control codes are on page 62.

7

1. Introduction

Part Names of the Remote Control

 

1

POWER

INFO.

2

3

IMAGE

INPUT AUTO PC

4

6

ASPECT

NO SHOW

7

8

MENU

 

9

5

10

 

11 12

BACK

L-CLICK R-CLICK

13 14

15

VOL

PAGE D.ZOOM

17

 

 

16

FREEZE

18

 

 

 

 

 

RD-428E

1.Infrared Transmitter

Direct the remote control toward the remote sensor on the projector cabinet.

2.POWER Button

When the main power is on, you can use this button to turn your projector on.

NOTE: To turn on the projector, press and hold the POWER button for about 1 second.

5.INPUT Button

Selecting from INPUT List

Press and quickly release the INPUT button to display the INPUT list. Each time the INPUT button is pressed, the input source will change as follows: "Computer 1", "Computer 2", "Video" (VCR or laser disc player), "S-Video", To display the selected source, press the OK button or allow 2 seconds to elapse.

Detecting the Signal Automatically

Press and hold the INPUT button for a minimum of 2 seconds, the projector will search for the next available input source. Each time you press and hold the INPUT button for a minimum of 2 seconds, the input

source will change as follows:

Computer 1 → Computer 2 → Video → S-Video → Computer1 → ...

6.AUTO PC Button

Use this button to adjust an RGB source for an optimal picture.

See page 27.

7.ASPECT Button

Press this button once to display the Aspect select menu. Keep pressing will change aspect ratios. See page 41.

8.NO SHOW Button

This button turns off the image and sound for a short period of time. Press again to restore the image and sound.

9.MENU Button

Displays the menu for various settings and adjustments.

10.SELECT (Mouse) Button

: Use these buttons to select the menu of the item you wish to adjust.

You can use this button to turn your projector off.

NOTE: To turn off the projector, press this button twice.

3.INFO. Button

Provides the information on the current signal and projector settings. See page 46.

4.IMAGE Button

Press this button to display the Image adjustment menu to adjust Screen color, Image mode, Brightness, Contrast, Sharpness, Color and Color balance. See pages 39 to 40.

: Use these buttons to change the level of a selected menu item. A press of the button executes the selection.

When an image is magnified, the SELECT button moves the image. See page 29.

This button also works as a computer mouse when the supplied remote mouse receiver is connected with your computer. See page 31.

8

1. Introduction

2

4

7

9

11

13

15

16

POWER INFO.

IMAGE INPUT AUTO PC

ASPECT

NO SHOW

MENU

BACK

L-CLICK R-CLICK

VOL PAGE D.ZOOM

FREEZE

RD-428E

1

3

6

8

5

10

12

14

17

18

16.PAGE / Button

Use these buttons to operate your computer with the supplied remote mouse receiver. See page 31. You can use these buttons to scroll the viewing area of the window or to move to the previous or next slide in PowerPoint on your computer.

17.D. ZOOM (+) (–) Button

Use this button to adjust the image size up to 400%. The image is magnified about the center of the screen. See page 29.

18.FREEZE Button

This button will freeze a picture. Press again to resume motion. See page 29.

11.OK Button

Use this button to enter your menu selection. It works the same way as the OK button on the cabinet. See page 6.

12.BACK Button

It works the same way as the BACK button on the cabinet. See page 6.

13.L-CLICK Button

This button works as the mouse left button when the supplied remote mouse receiver is connected with your computer. See page 31.

14.R-CLICK Button

This button works as the mouse right button when the supplied remote mouse receiver is connected with your computer. See page 31.

15.VOL (+) (–) Button

Press (+) to increase the volume and (–) to decrease it.

9

1. Introduction

Battery Installation

1 Press firmly and slide the battery cover off.

2 Remove both old batteries and install new ones (AAA). Ensure that you have the batteries' polarity (+/–) aligned correctly.

3 Slip the cover back over the batteries until it snaps into place. Do not mix different types of batteries or new and old batteries.

Remote Control Precautions

Handle the remote control carefully.

If the remote control gets wet, wipe it dry immediately.

Avoid excessive heat and humidity.

Do not heat, take apart, or throw batteries into fire.

Ensure that you have the batteries' polarity (+/-) aligned correctly.

If you will not be using the remote control for a long time, remove the batteries.

Do not place the batteries upside down.

Do not use new and old batteries together, or use different types of batteries together.

Dispose of used batteries according to your local regulations.

Operating Range for Wireless Remote Control

Remote sensor on projector cabinet

Remote control

7m/22 feet

 

 

30°

30°

30°

30°

 

 

7m/22 feet

The infrared signal operates by line-of-sight up to a distance of about 7 m (22 feet) and within a 60-degree angle of the remote sensor on the projector cabinet.

The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.

10

Canon LV-7255 User Manual

2. Installation and Connections

This section describes how to set up your projector and how to connect video and audio sources.

To the wall outlet.

Your projector is simple to set up and use. But before you get started, you must first:

Set up a screen and the projector. See page 12.

Connect your computer or video equipment to the projector. See pages 14 to 18.

Connect the supplied power cord. See page 19.

NOTE: Ensure that the power cord and any other cables are disconnected before moving the projector. When moving the projector or when it is not in use, cover the lens with the lens cap.

11

2. Installation and Connections

Setting Up the Screen and the Projector

Selecting a Location

The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 25" measured diagonally when the projector is roughly 0.9 m (3.1’) from the wall or screen. The largest the image can be is 300" when the projector is about 7.6 m (25.0’) from the wall or screen. Use the drawing below as a guide.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.6m

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.0m

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.8m

 

 

 

 

 

 

300"

 

 

 

 

Zoom (max.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.0m

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

200"

192"

 

 

 

 

Zoom (min.)

 

 

 

 

 

 

 

 

 

 

1.0m

 

 

80"

 

 

 

150"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0.9m

 

 

 

 

 

 

126"

 

 

 

 

 

 

 

 

 

H1

 

 

 

 

 

 

 

 

40"

 

 

 

 

 

 

 

96"

 

 

 

Screen

 

 

 

 

 

 

 

 

 

 

 

 

 

25"

 

 

 

 

 

50"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Optional axis when image is projected

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

at right angle to the screen.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Throw Distance and Screen Size

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Screen size (W x H cm)

 

 

25”

 

30”

 

40”

 

 

60”

 

80”

100”

 

150”

 

180”

200”

250”

300”

 

 

51 x 38

 

61 x 46

 

81 x 61

122 x 91

163 x 122

203 x 152

305 x 229

366 x 206

406 x 305

508 x 381

610 x 457

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Projection distance

 

 

 

 

1.0 m

 

1.5 m

2.0 m

2.5 m

 

3.8 m

 

4.5 m

5.0 m

6.3 m

7.6 m

Zoom (max)

 

 

 

 

 

 

 

 

 

 

 

(3.2’)

 

(4.9’)

(6.6’)

(8.3’)

 

(12.4’)

 

(14.9’)

(16.6’)

(20.8’)

(25.0’)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Projection distance

 

 

0.9 m

 

1.1 m

 

1.5 m

 

2.3 m

3.1 m

3.9 m

 

5.9 m

 

7.1 m

 

Zoom (min)

 

 

(3.1’)

 

(3.8’)

 

(5.1’)

 

(7.7’)

(10.3’)

(12.9’)

 

(19.4’)

 

(23.3’)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H1

 

 

34 cm

 

41 cm

 

55 cm

 

82 cm

110 cm

137 cm

 

206 cm

 

247 cm

274 cm

343 m

411 m

 

 

(1.1’)

 

(1.4’)

 

(1.8’)

 

(2.7’)

(3.6’)

(4.5’)

 

(6.8’)

 

(8.1’)

(9.1’)

(11.3’)

(13.6’)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H2

 

 

4 cm

 

5 cm

 

6 cm

 

9 cm

12 cm

15 cm

 

23 cm

 

27 cm

31 cm

38 cm

46 cm

 

 

(0.1’)

 

(0.2’)

 

(0.2’)

 

(0.3’)

(0.4’)

(0.5’)

 

(0.8’)

 

(0.9’)

(1.0’)

(1.3’)

(1.5’)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H1 and H2: H1 is the height of the screen from the intersection of optical axis and screen surface, and H2 is the height of the intersection when an image is projected at right angle to the screen.

TIP:

For the relationship between the screen size and projection distance, see the table on page 61.

The sizes in the above table have been obtained assuming that the aspect ratio is 4:3. They may vary from the actual sizes depending on the type of the projected image.

The Zoom lever adjusts the image size (diagonal) +/- 20%.

NOTE:

This projector can be hung from the ceiling (Ceiling mounted) with it turned up side down.

When a translucent screen is used, the projector can project an image from behind the screen (Rear).

When the projector is hung from the ceiling or projector projects an image from behind the screen, the image must be inverted vertically or horizontally. See page 43.

• When hanging the projector from the ceiling, optional brackets (part No. LV-CL12) are required.

12

2. Installation and Connections

WARNING

Installing your projector on the ceiling must be done by a qualified technician. Contact your dealer for more information.

Do not attempt to install the projector yourself.

Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged.

Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 41˚F (5˚C) and 95˚F (35˚C).

Do not expose the projector to moisture, dust, or smoke. This will harm the screen image.

Ensure that you have adequate ventilation around your projector so heat can dissipate. Do not cover the vents on the side or the front of the projector.

Reflecting the Image

Using a mirror to reflect your projector's image enables you to enjoy a much larger image. Contact your dealer if you need a mirror system. If you're using a mirror system and your image is inverted, use the MENU and SELECT buttons on your projector cabinet or your remote control to correct the orientation. See page 43.

13

2. Installation and Connections

Making Connections

NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.

*If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software.

Enabling the computer’s external display

Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector. When using a PC compatible laptop, a combination of function keys will enable/disable the external display. Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on or off. For more details, refer to your computer’s owner’s manual.

Connecting Your PC or Macintosh Computer

NOTE: The COMPUTER 1 connector supports Plug & Play (DDC2).

ANALOG IN-1

ANALOG IN-2

VIDEO

L AUDIO IN R

ANALOG IN-1

AUDIO IN ANALOG IN-2

IN

 

 

 

S-VIDEO

MONO

AUDIO OUT

SERVICE PORT

L AUDIO IN R

IN

 

 

MONO

VGA cable (supplied)

To mini D-Sub 15-pin connector on the projector. It is recommended that you use a commercially available distribution amplifier if connecting a signal cable longer than the supplied one.

PHONE

IBM VGA or Compatibles (Notebook type) or Macintosh (Notebook type)

Audio cable (not supplied)

PHONE

NOTE: For older Macintosh, use a commercially available pin adapter (not supplied) to connect to your Mac's video port.

IBM PC or Compatibles (Desktop type) or Macintosh (Desktop type)

NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.

NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan converter.

This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.

*When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly: Project an image to fill the screen and then press the AUTO PC button on the remote control or the projector cabinet.

14

Loading...
+ 51 hidden pages