Candy CSD 68-80 User Manual

Size:
2.64 Mb
Download

CSD 68-80/CSD68S-80

This manual contains sections of Safety Instructions,Operating Instructions, Installation Instructions and Troubleshooting Tips etc. Carefully reading it before using the dishwasher will help you to use and maintain the dishwasher properly.

To review the section on Troubleshooting Tips will help you to solve some common problems by yourself and not need to ask for the help of professional technicians.

The manufacturer, following a policy of constant development and up-datingof the product, may make modifications without giving prior notice.

. . . . . . . . . . . . . . . . . . 1

Control Panel . . . . . . . . . . . . . . . . . . . . . . . .2 Dishwasher Features . . . . . . . . . . . . . . . . . 2 Wash Cycle Table . . . . . . . . . . . . . . . . . . . . 3 Water Softener . . . . . . . . . . . . . . . . . . . . . . 4 Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rinse Aid . . . . . . . . . . . . . . . . . . . . . . . . . 5,6 Loading the Dishwasher Rack . . . . . . . . 6,7 Turning On the Appliance . . . . . . . . . . . . . . 7 Filtering System . . . . . . . . . . . . . . . . . . . . . 8 Caring for the Dishwasher . . . . . . . . . . . . . 9

About Electricity connection . . . . . . . . . . 10 About the Unicouple . . . . . . . . . . . . . . . . .10 Water Connection . . . . . . . . . . . . . . . . . . . 11 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 11

Before calling for service. . . . . . . . . . 12,13

Under certain conditions, Hydrogen gas may be produced in a hot-watersystem that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot-watersystem has not been used for such a period, before using the dishwasher turn on allhot-waterfaucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

This appliance complies with international safety standards, and is fitted with a plug with earth connection to ensure complete earthing of the product.

Before connecting the appliance to the mains supply it is important to ensure:

That the supply socket is properly earthed.That your electricity supply is capable of meeting the consumption requirements listed on the rating plate of your appliance.

Ensure that your product is properly earthed. In the absence of adequate earthing you will notice that when touching the metal parts of your appliance an electrical dispersion can be felt, due to the presence of a radio interference suppressor.

This appliance complies with Directives 89/336/EEC, 73/23/EEC and following changes.

Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.

Do not touch the heating element during or immediately after use.

Do not wash plastic items unless they are marked dishwasher safe or the equivalent. For plastic

items not so marked, check the manufactures recommendations.

Use only detergent and rinse additives designed for an automatic dishwasher. Never use soap , laundry detergent, or hand washing detergent in your dishwasher. Keep these products out of children.

Keep child away from detergent and rinse aid, keep child away from the open door of the dishwasher, there could still be some detergent left inside.

The door should not be left in the open position since this could present a tripping hazards.

During installation, the power supply must not be excessively or dangerously bent or flattened.

Do not tamper with controls.

The appliance is not intended for use by young children or infirm persons without supervision.

Dishwasher detergents are strongly alkaline,they can be extremely dangerous if swallowed.Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open.

Important: when the appliance location is on carpet floors, attention must be paid so as to ensure that there is no obstruction to the bottom vents.

Do not operate your dishwasher unless all enclosure panels are properly inplace. Open the door very carefully if the dishwasher is operating,

there is a risk of water squirting out.

Do not place any heavy objects of stand on the door when it is open. The appliance could tip forward.

When loading items to be washed:

1)Locate sharp items so that they are not likely to damage the door seal;

2)Load sharp knives with the handles up to reduce the risk of cut-typeinjuries.

When using your dishwasher, you should prevent plastic item from contacting with heating element.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

Please dispose of packing materials properly.

Use the dishwasher only for its intended function.

Remove the door to the washing compartment when removing an old dishwasher from service or discarding it.

Young children should be supervised to ensure that they do not play with the appliance.

Check that the detergent receptable is empty after completion of the wash cycle.

Cutlery is washed best if it is placed in the basket with handles downwards.

Warning:

knives and other utensils with sharp points must be loaded in the basket with their points down or placed in a horizontal position.

1

To get the best performance from your dishwasher,read all operating instructions before using it for the first time.

9

1

2

3

4

5

 

8

 

 

 

6

10

 

 

 

 

 

 

1 Pre-rinselight: Blink duringpre-rinse.2 Wash light: blink during wash.

3 Rinse light: blink during rinse.

4 Drying light: blink during drying.

5Salt empty light: To come on when the softener needs to be refilled(Certain model only).

6 Door Handle: Pull it to open the door.

7Washing Program Selector: Turn the knob clockwise to select wash cycles.

8ON/OFF Button: To turn ON/OFF the power supply.

NOTE: this model has a "broken remember" function, which means that power supply broken down during washing

will not reset the current washing program. So you can't cancel a program by cutting off the power. pls see the section entitled "change a program".

9Power Light : To come on when the ON/OFF Button is Pressed down.

10Start / Reset Button: Press this button to start or pause the selected program. When the program start one of the lights will blink.

1

7

 

 

 

 

 

2

 

 

 

3

8

 

 

4

 

 

 

5

9

 

 

6

10

11

12

1

2

3

Upper Basket

Spray Arms

Lower Basket

4

5

6

Water Softener

Main Filter

Detergent Dispenser

7

8

9

Cup Shelf

10

Rinse Aid Dispenser

Silverware Basket

11

Drain pipe connector

Coarse Filter

12

Inlet pipe connector

2

 

 

 

 

 

 

For the heaviest soiled loads,

Pre-rinse

 

 

 

such as pots,pans,casserole

Pre-rinse(45°C)

8/24 gr

 

dishes and dishes that have

Wash (70°C)

 

been sitting with dried food

Rinse (75°C)

 

 

 

on them for a while.

Drying

 

 

 

 

 

 

 

For normally soiled loads,

Pre-rinse

 

 

 

Wash (50°C)

 

 

 

such as pots, plates,glasses

4/20 gr

 

and lightly soiled pans.

Rinse (70°C)

 

standard daily cycle.

Drying

 

 

 

 

 

 

 

 

 

Pre-rinse

 

 

 

For lightly soiled loads,such

Wash (45°C)

4/20 gr

 

as plates,glasses,bowls and

Rinse (65°C)

 

 

 

 

lightly soiled pans.

 

 

 

Drying

 

 

 

 

 

 

 

 

 

 

 

 

Daily wash in only 1 hour.

Pre-rinse

 

 

 

Suitable for normal soiled

Wash (70°C)

20 gr

 

dishes that are to be washed

 

Rinse (65°C)

 

 

 

straight after a meal (max 6 plate

 

 

 

Drying

 

 

 

settings).

 

 

 

 

 

 

 

 

Wash (50°C)

 

 

 

A shorter wash for lightly soiled

Rinse (55°C)

15 gr

 

loads (max 4 plate settings).

Drying

 

 

 

 

 

 

 

 

To rinse dishes that you

Pre-rinse

 

plan to wash later that day.

 

 

 

 

 

 

 

 

 

 

 

1Draw out the lower and upper basket, load the dishes and push them back. It is recommended that loading the lower basket first, then the upper one (see the section entitled " Loading the Dishwasher " ).

2Pour in the detergent(see the section entitled, " Salt, Detergent and Rinse Aid " ).

3With a little force to ensure the door is properly closed. NOTE: A click could be heard when the door is closed

perfectly.

4Insert the plug into the socket.

The power supply is 220-240VAC50Hz, the specification of the socket is 12A 250 VAC, Make sure that the water supply is turned on to full pressure.

5

Press the ON/OFF button

6

Turn the knob located on the right of the control panel in

the clockwise direction until the number or the symbol

7

for the cycle

Press the Start/Reset button to start the washing.

8When the washing is over, you can shut off the switch by pressing on/off button.

Premise: A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been released, and the appliance may have already drained the wash water. In this case, the detergent dispenser must be refilled (see the paragraph entitled " Loading the Detergent " ).

1Please press the Start/Reset button and last more than three seconds, this will cancel the current programme. (NOTE: turning off the appliance by pressing the on/off button can not cancel the current programme, because this model has a "broken remember" function.)

2Turn around the Washing Program Selector to select the desired programme.

3Press the Start/Reset button to start the washing.

NOTE: If you open the door when washing, the machine will pause. When you close the door and press the Start/Reset button, the machine will keep on working after 10 seconds.

The four program lights shows the state of the dishwasher:

a)All program lights off-----------------

stand by

b)One of the program lights on-----------

pause

c)One of the program lights blinking-------

run

If all the lights begin to glimmer, that indicates the machine is out of order, please turn off the main power and water supply before calling a service.

3

If your model have not water softener, you may skip this section.

There are two ways to reduce the water hardness: one way is using water softener, the other is using detergent.

The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils.

The appliances is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.

Always use salt intended for use with dishwashers.

The salt container is located beneath the lower rack and should be filled as follows:

1 Remove the lower basket and then unscrew and remove the cap from the salt container.

2

3

4

If you are filling the container for the first time ,fill 2/3 of its volume with water.

Place the end of the funnel(supplied) into the hole and introduce about 2kg of salt .It is normal for a small amount of water to come out of the salt container

Carefully screw the cap back on.

1.The salt container must be refilled when the salt warning light comes on. Though the salt container is filled enough, the indicator light may not black out before the salt fully dissolve.

2. If there are spills of the salt, a soak program could be run to wipe them out.

The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimize and customize the level of salt consumption so that the salt consumption could be set proceed as follows:

1 Unscrew the cap from the salt container.

2 There is a ring on the container with an arrow on it (see Figure to the side), if necessary, rotate the ring in the anticlockwise direction from the"-"Setting

toward the "+" sign, based on the hardness of the water being used.It is recommended that adjustments should be made in accordance with the following schema:

 

WATER HARDNESS

 

Selector

Salt consumption

Auto nomy

°fH

 

dH

mmol/l

Position

(gram/cycle)

(cycles/2kgs)

0~10

0

-5

0-1.0

-

0

/

10~25

5-14

1.0-2.5

/

20

60

25~50

14

-28

2.5-5.0

MED

40

40

 

 

 

+

 

 

>50

>28

>5.0

60

25

 

 

 

 

 

 

 

Contact your local water board for information on the hardness of your water supply.

4

YOU MAY NOT ADD TOO MUCH DETERGENT TO PREVENT THE FORMATION OF DEPOSITS BECAUSE YOUR DISHWASHERS HAVE SPECIALLY-DESIGNEDWATER SOFTENERS.

The dispenser must be refilled before the start of each wash cycle following the instructions provided in the" Wash Cycle Table".Your dishwashers use less detergent and rinse aid than conventional dishwashers. Generally, only one tablespoon of detergent is needed for a normal wash load. Also, more heavily soiled items need more detergent. Always add the detergent just before starting dishwasher, otherwise it could get damp and will not dissolve properly.

IF THE WATER ISN'T TOO HARD, YOU MAY ALSO PREVENT THE FORMATION OF DEPOSITS BY ADDING DETERGENT.

The amount of detergent needed can vary due to differences in water hardness. To determine the water hardness in your area, contact your local water utility or area water softening company. The harder the water, the more detergent you may need. Remember, you should adjust the amount of detergent you use by small amounts until you find the correct amount.

Dishwasher detergent is corrosive! Take care to keep it out of reach of children.

To remove hard water spots, try the following:

Run dishes through a normal wash program.

Remove all metal dishware, such as cutlery, pans, etc., from the dishwasher.

Do not add detergent.

Pour two cups of vinegar into a bowl and set the bowl face up on the lower rack of the dishwasher.

Run the dishes through a normal wash program.

If this doesn't work, try the same process with 1 / 4 cup of citric acid crystals instead of vinegar.

Use only detergent specifically made for use in dishwashers. Keep your detergent fresh and dry. Don't put powder detergent

into the dispenser until You're ready to wash dishes.

To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.

Pour the rinse aid into the dispenser, being careful not to overfill.

Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.

The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes that can leave spots and streaks. It also improves drying by allowing water to "sheet" off the dishes.

Your dishwashers are designed to use liquid rinse aids. The rinse aid dispenser is located inside the door next to the

detergent dispenser. To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely black. The dispenser holds about 100 ml of liquid rinse aid.

Be careful not to overfill the dispenser, because this could cause oversudsing. Wipe away any spills with a damp cloth. Don't forget to replace the cap before you close the dishwasher door.

If you have soft water, you may not need rinse aid for it may cause a white film to develop on your dishes.

A measured amount of rinse aid is released during the final rinse. As with detergent, the amount of rinse aid needed for your dishes depends on the hardness of the water in your area. Too much rinse aid can result in lather of foaming and cause cloudiness or steaks on your dishes. If the water in your area is very soft, you may not need rinse aid. If you do,you can dilute the rinse aid with an equal amount of water.

The rinse aid dispenser has six settings. Always start with the dispenser set on " 1 ". If spots and poor drying are problems, increase the amount of rinse aid dispensed by removing the dispenser lid and rotating the dial to "2". If the dishes still are not drying properly or are spotted, adjust the dial to the next higher number until your dishes are spot-free.We suggest you to set on "4" .

(If only four settings we suggest you to set on "2".)

5

If there is no rinse aid warning light in the control panel, you can judge the amount of rinse aid by the following means. The black dot on the rinse aid dispenser indicates the amount of rinse aid in the dispenser. As the rinse aid diminishes, the size of the black dot decreases. You should never let the rinse aid get below 1 / 4 full.

As the rinse aid diminishes, the size of the black dot on the rinse aid level indicator changes, as illustrated below.

Full

3 / 4 full

1 / 2 full

1 / 4 full - Should refill to eliminate spotting Empty

The upper rack is designed to hold more delicate and lighter dishware such as glasses, coffee and tea cup and saucers, as well as plates, small bowls and shallow pans(as long as they are not too dirty).

Position the dishes and cookware so that they do not get moved by the spray of water.

The upper rack can be adjusted for height by putting wheels of different height into the rails.

 

 

 

1

1

2

 

2

 

 

 

3

 

 

6

4

 

 

 

 

3

5

5

 

 

 

6

 

4

 

 

Cups

Small serving bowl

Large serving bowl

Glasses

Saucers

Dish

We recommend that you place large items which are most difficult to clean into the lower rack: pots, pans, lids, serving dishes and bowls, as shown in the figure to the right.

It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the rotation of the top spray arm.

Pots, serving bowls, etc, must always be placed top down.

Deep pots should be slanted to allow water to flow out.

The bottom rack feature fold down tine rows so that larger or more pots and pans can be loaded.

1

3

4

1

2

 

 

3

 

 

4

 

 

5

24

5

Oval platter Dinner plates Soup plates Dessert dishes Silverware basket

6

Silverware should be placed in the silverware basket with handles at the bottom: If the rack has side baskets, the spoon should be loaded individually into the appropriate slots, Especially long utensils should be placed in the horizontal position at the front of the upper rack.

1

4

5

2

1

4

5

2

1

4

5

 

 

 

 

1

4

5

2

1

4

5

2

4

4

5

 

 

 

 

7

4

5

2

8

3

5

 

1

3

3

2

 

 

 

 

1

3

3

2

1

3

3

2

6

3

6

1

Forks

5

Knife

2

Soup spoons

6

Serving spoon

3

Dessert spoons

7

Gravy ladle

4

Teaspoons

8

Serving fork

Do not let any item extend through bottom.

When the working cycle has finished, the buzzer of dishwasher will mooing 8 second ,then stop . Turn off the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better.

A forgotten dish can be added any time before the detergent cup opens.

 

1

Open the door a little to stop the washing.

3

2

After the spray arms stop working,you can open the door

4

 

completely.

 

Add forgotten dishes.

Close the door, the dishwasher will work after ten second.

It is dangerous to open the door when washing,because the hot water may be scalded to you.

7

For your convenience, we have placed the drain pump and filtering system within easy reach inside the tub. There are three components of the filtering system: the main filter, the coarse filter, and the fine filter.

1 2

3

1Main filter

Food and soil particles trapped by this filter are pulverized by a special jet on the lower spray arm and washed down the drain.

2Coarse filter

Larger items, such as pieces of bone or glass, that could clog the drain are trapped in the coarse filter. To remove an item caught in this filter, gently squeeze the tabs on top of this filter and lift it out.

3Fine filter

This filter holds soil and food residue in the sump area and prevents it from being redeposited on the dishes during a cycle.

If your dishwasher is left in an unheated place during the winter, ask a service technician to:

 

1

Cut off electrical power to the dishwasher. Remove

 

 

fuses or trip circuit breaker.

 

2

Turn off the water supply and disconnect the water

 

 

inlet pipe from the water valve.

Uncrew

3

Drain water from the inlet pipe and water valve.

 

 

(Use a pan to catch the water.)

4Reconnect the water inlet pipe to the water valve.

5Remove the plastic sump cover in the tub the bottom and use a sponge to soak up water in rubber boot.

It is necessary to clean the spray arms regularly for hard water chemicals will clog the spray arm jets and bearings. To remove the spray arm, screw off the nut to take out the washer on top of the spray arm and remove the arm. Wash the arms in soapy and warm

water and use a soft brush to clean the jets. Replace them after rinsing them thoroughly.

Filter assembly

For best performance and results, the filter assembly must be cleaned.

The filter efficiently removes food particles from the wash water, allowing it to be recirculated during the cycle. For this reason, it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and cup under running water. To remove the filter assembly, pull on the cup handle in the upward direction. The entire filter assembly should be cleaned at least once a month.

To clean the coarse filter and the fine filter, use a cleaning brush. Then, reassemble the filter parts as shown in the figures left and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward.

The dishwasher must never be used without the filters. Improper replacement of the filter may reduce the performance level of the appliance and damage dishes and utensils.

Never run the dishwasher without the filters in place.

8