Campbell Hausfeld CHN10500 User Manual

Size:
4.32 Mb
Download

See Warranty on page 8 for important information about commercial use of this product.

Operating Instructions

CHN10500

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

7/8 inch 23g

Micro Pin Nailer

Table of Contents

 

Description . . . . . . . . . . . . . . . . . . . . .

1

Unpacking . . . . . . . . . . . . . . . . . . . . . .

1

Safety Guidelines . . . . . . . . . . . . . . . .

1

Important Safety Information . . . . . .

1

Tool Components and

 

Specifications . . . . . . . . . . . . . . . . . . . .

2

Operating Instructions . . . . . . . . . . . .

4

Lubrication . . . . . . . . . . . . . . . . . . . .

4

Recommended Hookup . . . . . . . . . .

4

Operational Mode . . . . . . . . . . . . . .

5

Trigger Only Mode . . . . . . . . . . . . . .

5

Loading/Unloading The Tool . . . . . .

5

Adjusting Direction of Exhaust . . . .

5

Clearing A Jam From The Tool . . . .

5

User-MaintenanceInstructions . . . . .

5

Interchange Information . . . . . . . . . .

6

Troubleshooting Chart .. .. .. .. .. .. .. .. .. .. .. ..

6

Warranty . . . . . . . . . . . . . . . . . . . . . . .

8

Description

This pin nailer is designed for tacking decorative trim, glazing strips, small picture frames and cabinetry trim.. Features include: adjustable exhaust, narrow nose for fitting in tight spaces, rubber comfort grip, auto-adjustingnail height mechanism, and trigger lock..

Unpacking

After unpacking the unit, inspect carefully for any damage that may have occurred during transit.. Make sure to tighten fittings, bolts, etc.., before putting unit into service..

Safety Guidelines

This manual contains information that is very important to know and understand.. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS.. To help

recognize this information, observe the following symbols..

Danger indicates an imminently

hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially

hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially

hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates important

information, that if not followed, may cause damage to equipment.

NOTE: Information that requires special attention..

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

This manual contains safety, operational and maintenance information.. Contact your Campbell Hausfeld representative if you have any questions..

When using tools, basic precautions should always be followed, including

the following:

Model CHN10500

Locate model and date code on tool and record below:

Model No..: _____________________

Date Code: _____________________

Retain these numbers for future reference..

California proposition 65

This product or

its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

You can create dust when you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

Campbell Hausfeld Tools meet or exceed Industries’ Standards as set forth by the American National Standard

IN726401AV 4/10

Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002..

 

© 2010 Campbell Hausfeld / Scott Fetzer

For parts, product & service information

 

visit www.chpower.com

Important Safety Instructions

 

able to create sparks resulting in the

 

better control of the tool in

(Continued)

 

ignition of the dust or fumes..

 

unexpected situations..

General

c..

Keep bystanders, children, and

e..

Use safety equipment. A dust mask,

 

 

 

 

 

 

visitors away while operating the

 

non-skidsafety shoes and a hard

a..

To reduce the risks of

 

 

 

tool. Distractions are able to result in

 

hat must be used for the applicable

 

 

electric shock, fire, and

 

 

 

 

 

the loss of control of the tool..

 

conditions..

 

 

 

injury to persons, read all

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the instructions before

 

Personal Safety

f..

Always wear eye

 

 

 

 

 

using the tool.

a..

Stay alert. Watch what you are

 

protection.

b.

Be thoroughly familiar with the

g.. Always wear hearing

 

 

doing and use common sense

 

 

 

 

 

 

 

controls and the proper use of the

 

 

protection when using

 

 

 

when operating the tool. Do not

 

 

 

equipment.. Follow all instructions..

 

 

the tool. Prolonged

 

 

 

use the tool while tired or under

 

 

 

Contact your Campbell Hausfeld

 

 

exposure to high intensity

 

 

 

 

the influence of drugs, alcohol,

 

 

 

representative if you have any

 

or medication. A moment of

 

noise is able to cause

 

 

questions..

 

 

hearing loss..

 

 

 

inattention while operating the

 

 

 

 

 

 

 

 

 

 

 

 

 

c.

Only persons well acquainted with

 

tool increases the risk of injury to

h.. Do not attach the hose or tool to

 

 

these rules of safe operation should

 

persons..

 

your body. Attach the hose to the

 

 

be allowed to use the unit..

b..

Dress properly. Do not wear loose

 

structure to reduce the risk of loss of

 

 

 

Read and

 

balance if the hose shifts..

 

 

 

 

clothing or jewelry. Contain long

 

 

 

 

 

 

 

 

 

understand tool

 

 

 

 

 

 

 

 

 

 

 

hair. Keep hair, clothing, and

i..

Always assume that the tool

 

 

 

 

labels and manual. Failure to follow

 

 

gloves away from moving parts.

 

contains fasteners. Do not point

warnings, dangers, and cautions could

 

 

 

Loose clothes, jewelry, or long

 

the tool toward yourself or anyone

result in DEATH or SERIOUS INJURY.

 

 

Work Area

 

hair increases the risk of injury to

 

whether it contains fasteners or not..

 

persons as a result of being caught

j.

 

 

 

Do

a..

Keep the work area clean and well

 

 

 

 

 

in moving parts..

 

 

 

 

 

 

 

 

not nail on

 

 

 

 

 

 

 

 

 

 

 

 

lighted. Cluttered benches and dark

c..

Avoid unintentional starting.

 

top of another nail. This is able to

 

 

areas increase the risks of electric

 

cause the nail to be deflected and

 

 

 

Be sure the switch is off before

 

 

 

shock, fire, and injury to persons..

 

 

hit someone, or cause the tool to

 

 

 

connecting to the air supply. Do not

 

 

 

 

 

react and result in a risk of injury to

b.. Do not operate the tool

 

 

 

 

 

carry the tool with your finger on

 

persons.

 

 

in explosive atmospheres,

 

the switch or connect the tool to the

k..

 

 

 

Remove finger

 

 

 

 

 

 

 

 

such as in the presence

 

air supply with the switch on..

 

 

 

 

 

 

 

 

 

 

from the trigger

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

of flammable liquids,

 

d..

Do not overreach. Keep proper

 

when not driving fasteners. Never

 

 

 

 

 

 

gases, or dust. The tool is

 

carry the tool with finger on trigger,

 

 

 

footing and balance at all times.

 

Operating Instructions

 

 

 

 

 

 

 

 

Proper footing and balance enables

the tool is able to fire a fastener.

 

Tool Components and Specifications

Requires: 0..15 SCFM with 10

 

fasteners per minute @ 90 psi

Head Cap

Air inlet: 1/4 inch NPT

PIN SIZE RANGE: 3/8 inch to 7/8 inch

MAGAZINE CAPACITY:

110 headless pins, 23 g

WEIGHT: 1 lb.. 13 oz..

LENGTH: 8..25 inches

HEIGHT: 6..8 inches

MAXIMUM PRESSURE: 100 psi

PRESSURE RANGE: 60 psi – 100 psi

Adjustable Exhaust

Trigger Lock

Latch

Button

(other

side)

Trigger

Magazine

Nail Loading Area

 

 

Automatic Nail

Nail Discharge

Length Plate

Area

 

www.chpower.com

2

 

 

 

 

CHN10500

Important Safety Instructions

h..

Use only those fasteners listed

air to remain in the tool. Death or

(Continued)

 

in the Accessories section of this

serious personal injury could occur.

 

 

 

Always remain in a

 

manual. Fasteners not identified

 

 

 

for use with this tool by the tool

 

 

firmly balanced

 

Never place hands or any

position when using or handling the

 

manufacturer are able to result in

 

other body parts in the

tool.

 

a risk of injury to persons or tool

 

fastener discharge area of the

 

Avoid long extended

 

damage when used in this tool..

 

 

tool. The tool might eject a fastener and

 

periods of work

i.

Selecting an appropriate tool

could result in death or serious personal

with the tool. Stop using the tool if you

injury.

 

actuation system, taking into

feel pain in hands or arms.

 

 

Tool Use and Care

 

consideration the work application

 

 

for which the tool is used..

Never carry the tool by

 

 

 

a..

Use clamps or another practical way

 

Never use

 

the air hose or pull the

 

to secure and support the workpiece

 

 

 

gasoline

hose to move the tool or

 

to a stable platform. Holding the

or other flammable liquids

a compressor. Keep hoses

 

work by hand or against the body is

to clean the tool. Never use

away from heat, oil and

 

the tool in the presence of

sharp edges. Replace any hose that is

 

unstable and is able to lead to loss

 

flammable liquids or gases. Vapors

damaged, weak or worn. Personal injury

 

of control..

 

could ignite by a spark and cause an

or tool damage could occur.

b..

Do not force the tool. Use the

explosion which will result in death or

Always assume the

 

correct tool for the application.. The

serious personal injury.

tool contains

 

 

 

fasteners. Respect the tool as a working

 

correct tool will do the job better

 

 

 

 

 

implement; no horseplay. Always keep

 

and safer at the rate for which the

 

 

 

Do not remove, tamper

others at a safe distance from the work

 

tool is designed..

area in case of accidental discharge of

c..

Do not use the tool if the switch

with, or otherwise cause

fasteners. Do not point the tool toward

the trigger lock or trigger

yourself or anyone whether it contains

 

does not turn the tool on or off. Any

to become inoperable. Do

fasteners or not. Accidental triggering

 

tool that cannot be controlled with

not operate any tool which has been

of the tool could result in death or

 

the switch is dangerous and must be

modified in a like fashion. Death or

serious personal injury.

 

serious personal injury could result.

 

 

repaired..

 

 

 

 

 

d.

Disconnect the

 

 

Do not drive a fastener

 

tool from the air

Do not touch the trigger

on top of other

 

source before making adjustments,

fasteners. The fastener

 

unless driving fasteners.

 

doing tool maintenance, clearing

could glance and cause

 

Never attach air line to

 

jams, leaving work area,loading,

death or a serious puncture wound.

 

tool or carry tool while

 

or unloading the tool. Such

! WARNING

 

touching the trigger. The tool could

 

precautionary measures reduce the

 

eject a fastener which will result in

 

 

risk of injury to persons..

Do not operate or allow

 

death or serious personal injury. Also

e..

Store the tool when it is idle out

anyone else to operate

actuate the trigger guard to the safe

the tool if any warnings

 

of reach of children and other

position when not in use.

 

or warning labels are not legible.

 

untrained persons. A tool is

 

 

 

 

 

Warnings or warning labels are located

 

dangerous in the hands of untrained

 

 

on the tool magazine and body.

 

users..

Always disconnect the

Do not drop or

f..

Maintain the tool with care. Keep

tool from the power

throw the tool.

source when unattended,

Dropping or throwing the tool can

 

a cutting tool sharp and clean.. A

 

performing any maintenance or repair,

result in damage that will make the tool

 

properly maintained tool, with sharp

clearing a jam, or moving the tool to a

unusable or unsafe. If the tool has been

 

cutting edges reduces the risk of

new location. Do not load the tool with

dropped or thrown, examine the tool

 

fasteners when the trigger is depressed.

closely for bent, cracked or broken parts

 

binding and is easier to control..

 

The tool could eject a fastener causing

and air leaks. STOP and repair before

g..

Check for misalignment or binding

death or serious personal injury.

using or serious injury could occur.

 

 

 

 

of moving parts, breakage of parts,

 

 

Avoid using the

 

and any other condition that affects

 

 

tool when the

 

Always fit tool with a

magazine is empty. Accelerated wear on

 

the tool’s operation. If damaged,

 

fitting or hose coupling

the tool may occur.

 

have the tool serviced before using..

 

on or near the tool in

Clean and check all

 

Many accidents are caused by poorly

 

such a manner that all

 

air supply hoses

 

maintained tools.. There is a risk of

compressed air in the tool is discharged

 

and fittings before connecting the

 

bursting if the tool is damaged..

at the time the fitting or hose coupling

tool to an air supply. Replace any

 

is disconnected. Do not use a check

valve or any other fitting which allows

damaged or worn hoses or fittings.

Tool performance or durability may be

 

 

reduced.

 

 

 

www.chpower.com

3

Operating Instructions

Important Safety Instructions

b.. Never use oxygen, carbon dioxide,

1.

Disconnect the air

 

(Continued)

combustible gases or any bottled

 

 

supply from the tool

 

Service

gas as an air source for the tool.

 

 

 

to add lubricant..

 

Such gases are capable of explosion

 

 

 

a.. Tool service must be performed only

 

 

 

and serious injury to persons..

 

 

2.

Turn the tool so the air

 

by qualified repair personnel.

 

 

OIL

 

 

 

 

 

 

 

 

 

 

 

inlet is facing up.. Place

 

b.. When servicing a tool, use only

 

 

 

 

 

 

 

 

 

 

 

 

 

4-5drops of 30 W non-

 

identical replacement parts. Use

 

 

O

 

 

 

 

Do not use any type of

CO2

 

detergent oil into air inlet..

 

 

 

 

 

only authorized parts.

 

 

 

 

 

reactive gases, including, but

 

 

 

Do not use detergent

 

c.. Use only the lubricants supplied

not limited to, oxygen and

 

 

 

 

 

 

 

 

 

oils, oil additives, or airtool oils..

combustible gases, as a power source.

 

with the tool or specified by the

 

 

Air tool oils contain solvents which

Use filtered, lubricated, regulated

 

 

 

manufacturer.

 

 

 

compressed air only. Use of a reactive

 

will damage the tool's internal

 

 

Do not make any

gas instead of compressed air may

 

 

 

components..

 

modifications to

cause the tool to explode which will

 

3. After adding oil, run

 

the tool without first obtaining written

cause death or serious personal injury.

 

 

tool briefly.. Wipe off

 

approval from Campbell Hausfeld. Do

 

 

 

 

 

 

 

not use the tool if any shields or guards

 

 

 

 

 

 

any excess oil from the

 

are removed or altered. Do not use the

Use only a pressure-regulated

 

 

 

cap exhaust..

 

tool as a hammer. Personal injury or

 

 

 

 

 

compressed air source to limit 100 psi

 

 

 

tool damage may occur.

Recommended Hookup

 

Disconnect air

the air pressure supplied to

 

 

 

The illustration below shows the

the tool. The regulated pressure must

 

supply and release

not exceed 100 psi. If the regulator

 

 

recommended hookup for the tool..

tension from the pusher before

 

 

fails, the pressure delivered to the

 

 

1.

The air compressor

 

attempting to clear jams because

 

 

60 psi

tool must not exceed 200 psi. The tool

fasteners can be ejected from the front

 

must be able to

Min.

could explode which will cause death or

 

 

 

of the tool. Personal injury may occur.

serious personal injury.

 

 

 

 

maintain a minimum

100 psi

 

 

 

 

 

Max.

Air Source

 

 

 

 

 

 

of 60 psi when the

Save These Instructions

 

 

 

 

a.. Never connect to an air source that

 

Do Not Discard

 

 

 

tool is being used.. An inadequate air

 

 

 

 

supply can cause a loss of power and

is capable of exceeding 200 psi.

 

 

 

 

 

 

Operating Instructions

 

 

 

inconsistent driving..

 

Over pressurizing the tool is able

 

 

 

 

 

 

2. An oiler can be

 

to result in bursting, abnormal

Lubrication

 

 

 

 

 

 

 

 

used to provide oil

 

operation, breakage of the tool or

 

 

 

 

 

 

 

 

 

 

 

 

This tool requires lubrication before

 

 

 

circulation through

 

serious injury to persons.. Use only

 

 

 

 

using the tool for the first time and

 

 

 

the tool.. A filter can

 

clean, dry, regulated compressed air

 

 

 

 

before each use.. If an inline oiler is

 

 

 

be used to remove

 

at the rated pressure or within the

 

 

 

 

used, manual lubrication through the

 

 

liquid and solid impurities which can

rated pressure range as marked on

 

 

air inlet is not required on a daily basis..

 

rust or “gum up” internal parts of

the tool.. Always verify prior to using

 

 

 

 

 

 

 

the tool..

 

the tool that the air source has been

 

The work surface

 

 

 

adjusted to the rated air pressure or

 

can become

 

 

3.

Always use air supply hoses with

within the rated air-pressurerange..

damaged by excessive lubrication.

 

 

 

a minimum working pressure

Proper lubrication is the owner’s

 

 

 

 

 

 

 

rating equal to or greater than the

 

responsibility. Failure to lubricate the

 

 

 

pressure from the power source if a

 

tool properly will dramatically shorten

 

 

the life of the tool and void your

 

 

 

regulator fails, or 150 psi, whichever

 

warranty.

 

 

 

 

 

 

 

Recommended Hookup

 

 

 

 

Regulator

 

 

 

 

Quick

 

 

 

Quick

Quick Plug

 

 

 

 

 

 

Coupler

 

 

 

 

 

Quick Plug

Coupler

(Optional)

(Optional)

 

 

 

Air Hose

Lubricator

Filter

www.chpower.com

4

CHN10500

Operating Instructions (Continued)

is greater.. Use 1/4 inch air hose for runs up to 50 feet.. Use 3/8 inch air hoses for 50 foot run or longer..

150 psi or greater

3/8 inch I..D..

4.Use a pressure regulator on the compressor, with an operating pressure of 0 psi - 125 psi.. A pressure regulator is required to control

the operating pressure of the tool between 60 psi and 100 psi..

Operational Mode

Always know the operational mode of

the tool before using. Failure to know the operational mode could result in death or serious personal injury.

Trigger Only Mode (with Trigger Lock)

The tool is a single-actuatordevice.. This mode requires that, with the trigger lock not positioned in the safe mode, only a pull of the trigger will fire a fastener..

Unlock

Lock

After verifying there are no fasteners in the tool, safety check the operation of the activated trigger lock to prevent the tool from firing a fastener before storage.. Always disconnect from compressed air when not in use..

LOADING/UNLOADING THE TOOL

1.Always disconnect the tool from the air supplybefore loading fasteners..

2. Push the latch button..

Latch

Button

Pull back on the

 

magazine cover fully..

 

3. Insert a stick of fasteners into themagazine under theautomatic nail length

plate.. Make sure

pointed ends of pins are resting on bottom ledge of magazine when loading.. Make sure pins are not dirty or damaged.. Pins are marked for direction of loading..

4. Push the magazine cover forward until latch engages..

5.Always unload all fasteners before removing tool from service.. Unloading is the reverse of loading, except always disconnect the air supply before unloading..

Adjusting The Direction Of The Exhaust

The tool is

equipped with an Rotate adjustable direction

exhaust deflector.. This is intended to allow the user to change the direction of the exhaust.. Simply twist the deflector to any direction desired..

Clearing A Jam From The Tool

1. Disconnect the air supply from the tool..

2.Remove all nails from the magazine (see "Loading/ Unloading The Nailer").. Failure to do so will cause the nails to eject from the front of the nailer..

3.Completely remove the two (2) small nose screws and the top nose plate to reveal the jammed fastener..

4.Using caution not to bend or damage the driver blade, use a pick or some other pointed object to pry free and clear the jammed fastener..

User-MaintenanceInstructions

Technical Service

Please call our Tool Hotline at 1-800-543-6400with any questions regarding the operation or repair of this tool or for additional copies of this manual..

Fastener And Replacement Parts

Use only 23 gauge headless micropins

(or equivalent - see Fastener Interchange Information). Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number.

Tool Repair

Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently..

DRIVER BLADE CARE and REPLACEMENT

In order to properly drive the tiny micropins and leave a nearly

undetectable hole, the tips of the driver blades end in a fine point and are therefore quite vulnerable to abuse and extended use..

To maximize the life of the blade, closely examine fasteners for defects.. Do not use defective or improper fasteners.. Also load fasteners in the proper orientation; the pin points and the arrows always point toward the wood surface.. Drive fasteners into wood products only (see "Loading/ Unloading The Nailer")..

Even with good care, extended use of the tool may eventually lead to tip failure.. Replacement driver assemblies can be purchased by calling 1-800-543-6400and refer to part number SKN12600AV..

www.chpower.com

5

Operating Instructions

User-MaintenanceInstructions (Continued)

Replace assembly by first removing the four (4) head cap screws using the 3 mm hex wrench provided.. Remove

head cap and components to access the driver piston.. Remove and replace driver assembly using your fingers.. Replace components and head cap as removed..

Assembly Procedure For Seals

When repairing a tool, the internal parts must be cleaned and lubricated.. Parker O-lubeor equivalent must be used on allo-rings..Eacho-ringmust be coated withO-lubebefore assembling.. A small amount of oil must be used on all moving surfaces and pivots.. After reassembling, a few drops of 30Wnon-detergentoil or equivalent, must be added through the air line before testing..

Storage

The tool should be stored in a cool dry place..

Interchange Information

Can use 3/8 inch to 7/8 inch pins from the following branded 23 g micropinners: Senco FP10, Air Locker P630, Porter Cable PIN100, Grex P635, and Max NF235A..

Troubleshooting Chart

Stop using tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.

Symptom

Possible Cause(s)

Corrective Action

Air leaking at trigger valve

O-Ringsin trigger valve housing are

Replace o-rings

area..

damaged

 

 

 

 

 

 

 

Air leaking between housing

1.

Damaged o-rings

1.

Replace o-rings

and nose..

2.

Damage to bumper

2.

Replace bumper

 

 

 

 

 

 

Air leaking between housing

1.

Loose screws

1.

Tighten screws

and cap..

2.

Damaged seal

2.

Replace seal

 

 

 

 

 

 

Tool skips driving fastener

1.

Worn bumper

1.

Replace bumper

 

2.

Dirt in nose piece

2.

Clean drive channel

 

3.

Dirt or damage prevent fasteners or

3.

Clean magazine

 

 

pusher from moving freely in magazine

 

 

 

4.

Damaged pusher spring

4.

Replace spring

 

5.

Inadequate air flow to tool

5.

Check fitting, hose, or compressor

 

6.

Worn o-ringson piston or lack of

6.

Replace and lubricate o-rings

 

 

lubrication

 

 

 

7.

Damaged o-ringson trigger valve

7.

Replace o-rings

 

8.

Air leaks

8.

Tighten screws and fittings

 

9.

Cap seal leaking

9.

Replace seal

 

10.

Defect in automatic nail length plate

10.

Clear problem with plate

 

 

 

 

 

Tool runs slow or has loss of

1.

Tool not lubricated sufficiently

1.

Lubricate nailer

power

2.

Broken spring in cylinder cap

2.

Replace spring

 

 

3.

Exhaust port in cap is blocked

3.

Replace damaged internal parts

 

 

 

 

 

Fasteners are jammed in tool

1.

Guide on driver is worn

1.

Replace guide

 

2.

Fasteners are not correct size

2.

Use only recommended fasteners

 

3.

Fasteners are bent

3.

Replace with undamaged fasteners

 

4.

Magazine or nose screws are loose

4.

Tighten screws

 

5.

Driver is damaged

5.

Replace driver

www.chpower.com

6

CHN10500

Notes

www.chpower.com

7

Operating Instructions

Limited Warranty

1.DURATION: From the date of purchase by the original purchaser as follows: One (1) Year..

2.WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400

3..WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product..

4..WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This Campbell Hausfeld nailer or stapler..

5..WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the duration of the warranty period with the exceptions below..

6..WHAT IS NOT COVERED UNDER THIS WARRANTY:

A.Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION.. If this product is used for commercial, industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase.. Some States do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you..

B.ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT.. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you..

C.Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with product.. Accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions shall also include the removal or alteration of any safety devices.. If such safety devices are removed or altered, this warranty is void..

D.Normal adjustments which are explained in the owner’s manual(s) provided with the product..

E.Items or service that are normally required to maintain the product, e..g.. o-rings,springs, bumpers, debris shield,driver blades, gaskets, packings or seals,lubricants, or any other expendable part not specifically listed.. These items will only be covered for ninety (90) days from date of original purchase..Underlined items are warranted for defects in material and workmanship only..

7.RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which are defective, have malfunctioned and/or failed to conform within the duration of the specific warranty period..

8.RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A.Provide dated proof of purchase and maintenance records..

B.Call Campbell Hausfeld (800) 543-6400to obtain your warranty service options.. Freight costs must be borne by the purchaser..

C.Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s)..

9.WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts..

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights.. You may also have other rights which vary from state to state or country to country..

www.chpower.com

8

Voir la Garantie à la page 16 pour de l’information importante sur l’utilisation commercial de ce produit.

Instructions d’Utilisation

CHN10500

 

 

Veuillez lire et conserver ces instructions. Lire attentivement avant de commencer à assembler, installer, faire fonctionner ou entretenir l'appareil décrit. Protégez-vouset les autres en observant toutes les informations sur la sécurité. Négliger d'appliquer ces instructions peut résulter en des blessures corporelles et/ou en des dommages matériels ! Conserver ces instructions pour références ultérieures.

Cloueuse de micro pointes de

22,2 mm (7/8 po)

Table des matières

Descripion . . . . . . . . . . . . . . . . . . . . 1-FrDéballage . . . . . . . . . . . . . . . . . . . .1-FrDirectives de sécurité . . . . . . . . . . .1-Fr

Importantes instructions

de sécurité . . . . . . . . . . . . . . . . . . . . 1-Fr

Pièces détachées et fisch technique mécanisme de la l'outil . . . . . . . . . . 2-Fr

Mode d’emploi . . . . . . . . . . . . . . . . 4-FrGraissage . . . . . . . . . . . . . . . . . . .4-FrBranchement recommandé . . . . .4-FrMode d’opération . . . . . . . . . . . .5-FrMode séquentiel unique . . . . . . .5-Fr

Chargement/décharement de

 

l'outil . . . . . . . . . . . . . . . . . . . . . .

. 5-Fr

Ajustement de la direction

 

d'échappement . . . . . . . . . . . . .

. 5-Fr

Déblocage de la l'outil . . . . . . .

. 5-Fr

Instructions de maintenance

 

de l'utilisateur . . . . . . . . . . . . . . . .

. 5-Fr

Information d'interchangeabilité

. 6-Fr

Guide de dépannage . . . . . . . . . .

. 7-Fr

Garantie limitée . . . . . . . . . . . . . .

. 8-Fr

Description

Cette cloueuse de pointes est conçue pour l’installation de garnitures décoratives, bandes de vitrage, petits cadres et garniture d’armoires.. Les caractéristiques incluent : échappement réglable, buse étroite pour les endroits restreints, prise confort de caoutchouc, mécanisme de hauteur de clou autoajustable et verrou de gâchette..

Déballage

Dès que l’appareil est déballé, l’inspecter attentivement pour tout signe de dommages en transit.. S’assurer de resserrer tous les raccords, boulons, etc.. avant de le mettre en service..

Directives de Sécurité

Ce manuel contient de l’information très importante qui est fournie pour la SÉCURITÉ et pour ÉVITER LES

PROBLÈMES D’ÉQUIPEMENT.. Rechercher les symboles suivants pour cette information..

Danger indique une situation

hasardeuse imminente qui RÉSULTERA en perte de vie ou blessures graves.

Avertissement indique une

situation hasardeuse potentielle qui PEUT résulter en perte de vie ou blessures graves.

Attention indique une situation

hasardeuse potentielle qui PEUT résulter en blessures.

Avis indique de l’information

importante pour éviter le dommage de l’équipement.

REMARQUE : L’information qui exige une attention spéciale..

Importantes instructions de sécurité

INSTRUCTIONS PORTANT SUR UN RISQUE D’INCENDIE, UN CHOC ÉLECTRIQUE OU DES BLESSURES AUX PERSONNES

Ce manuel contient des informations concernant la sécurité, le fonctionnement et l’entretien.. Contacter votre représentant Campbell Hausfeld si vous avez des questions..

En utilisant les outils, il faut suivre

les précautions de base, y compris ce qui suit :

Modèle CHN10500

Trouver le numéro de modèle et le code date sur le chargeur de l’outil et inscrire plus bas :

No du Model : __________________

Code de date : __________________

Conserver ces numéros comme référence..

PRoposition 65 DE CALIFORNIE

Ce produit ou son cordon peuvent

contenir des produits chimiques qui, de l’avis de l’État de Californie, causent le cancer et des anomalies congénitales ou autres problèmes de reproduction. Lavez-vousles mains après la manipulation.

Vous pouvez créer de la poussière en coupant,

ponçant, perçant ou

meulant les matériaux tels que le bois, la peinture, le métal, le béton, le ciment ou autre maçonnerie. Cette

poussière contient souvent des produits chimiques reconnus pour causer le cancer, les déformations congénitales ou autres problèmes de la reproduction. Porter de l’équipement de protection.

MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie!

Joignez-laà ce manuel ouclassez-ladans un dossier pour plus de sécurité.

Les outils Campbell Hausfeld satisfont ou dépassent les normes de l’industrie tel qu’indiqué par l’American

IN726401AV 4/10

National Standard Institute/International Staple, Nail and Tool Association sous ANSI/ISANTA SNT-101-2002..

 

© 2010 Campbell Hausfeld / Scott Fetzer

1-Fr

Instructions d’utilisation

Importantes instructions

 

L’outil peut produire des étincelles

d..

Ne pas trop se pencher. Garder bon

de sécurité (Suite)

 

menant à une inflammation de

 

pied et bon équilibre en tout temps.

Généralité :

 

poussières ou de fumées..

 

Ceci permet d’avoir un meilleur

c..

Garder les spectateurs, les enfants et

 

contrôle de l’outil dans les situations

a..

Pour réduire les risques

 

 

 

 

les visiteurs loin en utilisant l’outil.

 

imprévues..

 

 

de chocs électriques,

 

 

e..

Utiliser l’équipement de sécurité.

 

 

 

 

Les distractions peuvent faire perdre

 

 

d’incendie ou de blessures

 

 

 

 

 

 

le contrôle de l’outil..

 

Il faut utiliser un masque

 

 

aux personnes, lire toutes

 

 

 

 

 

 

 

 

 

antipoussières, des souliers de

 

 

les instructions avant

Sécurité personnelle

 

 

 

 

sécurité antidérapants et un casque

 

 

d’utiliser l’outil..

 

 

 

 

 

a..

Rester vigilant. Il faut regarder ce

 

de protection appropriés pour les

b.

Se familiariser avec ce produit, ses

 

 

que vous faites et utiliser son sens

 

conditions en cours..

 

 

commandes et son utilisation.. Suivez

 

commun en faisant fonctionner

f..

Toujours porter une

 

 

 

toutes les instructions.. Contacter

 

un outil. Ne pas faire fonctionner

 

 

 

 

 

protection pour les yeux.

 

 

 

votre représentant Campbell

 

l’appareil si vous êtes fatigué ou

 

 

 

 

 

g..

Toujours porter une

 

 

 

Hausfeld si vous avez des questions..

 

sous l’influence de drogues, d’alcool

 

 

 

 

 

protection auditive en

 

 

 

 

 

 

c.

Seules les personnes familières avec

 

ou de médicaments. Un moment

 

 

 

 

utilisant l’outil. Toute

 

 

 

ces règles d’utilisation sans danger

 

d’inattention en faisant fonctionner

 

 

 

 

 

 

exposition prolongée

 

 

 

devraient utiliser cette unité..

 

l’outil augmente le risque de

 

 

 

 

 

 

à des bruits de forte

 

 

 

 

Lire et comprendre

 

blessures..

 

 

 

 

 

 

 

 

intensité pourrait

 

 

 

 

les étiquettes et le

b..

Il faut s’habiller correctement.

 

provoquer une perte auditive..

 

 

 

 

manuel sur les outils. Ne pas suivre les

 

Ne pas porter de bijoux ou de

 

 

h..

Ne pas attacher le boyau d’air ou

avertissements, les dangers et les mises

 

vêtements amples. Attacher les

en garde pourrait causer la MORT ou de

 

 

l’outil à votre corps. Fixer le boyau

 

cheveux longs. Garder les cheveux,

 

GRAVES BLESSURES.

 

 

à la structure pour réduire le risque

 

les vêtements et les gants loin

 

 

 

 

 

 

 

 

de perte d’équilibre si le boyau se

Aire de travail

 

des pièces mobiles. Les vêtements

 

 

 

déplace..

a..

Garder l’aire de travail propre et

 

amples, les bijoux ou les cheveux

 

 

i..

Toujours assumer que l’outil

 

longs augmentent le risque de

 

 

bien éclairée. Les établis encombrés

 

 

 

 

blessures si quelque chose se prend

 

contient des attaches. Ne pas

 

 

et les coins sombres augmentent

 

 

 

 

 

dans les pièces mobiles..

 

pointer l’outil vers soi ou vers

 

 

les risques de chocs électriques,

 

 

 

 

 

 

 

quelqu’un d’autre qu’il y ait des

 

 

d’incendie et de blessures aux

c..

Éviter tout démarrage accidentel.

 

 

 

 

attaches ou non..

 

 

personnes..

 

S’assurer que l’interrupteur est

 

 

 

 

 

 

 

 

 

 

b..

Ne pas faire fonctionner

 

 

en position d’arrêt (off) avant de

j.

 

 

 

Ne pas clouer

 

 

 

 

 

 

 

 

 

 

 

 

brancher à l’alimentation d’air.

 

 

 

 

sur le dessus

 

 

l’outil dans une

 

 

 

 

 

 

 

 

 

 

Ne pas transporter l’outil avec le

 

d’un autre clou. Ceci pourrait faire

 

 

atmosphère explosive

 

 

 

 

 

 

 

doigt sur l’interrupteur ni brancher

 

dévier le clou qui pourrait alors

 

 

comme en présence

 

 

 

 

 

 

 

 

frapper quelqu’un ou l’outil pourrait

 

 

 

 

l’outil à l’alimentation d’air avec

 

 

 

de liquides, gaz

 

 

réagir provoquant des blessures.

 

 

 

l’interrupteur en marche..

 

 

 

ou poussières inflammables.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pièces détachées et fiche technique mécanisme de la l'outil

Chapeau de tête

EXIGE : 0,004 m3/min avec 10 une attaches par minute à 621 kPa

PRISE D’AIR : 1/4 po NPT

PLAGE DE TAILLE DE GOUPILLE: 3/8 po à 7/8 po

CAPACITÉ DU CHARGEUR :

110 goupilles sans tête, 23 g

POIDS : 0,82 kg

LONGUEUR : 20,96 cm (8..25 po)

HAUTEUR : 17,27 cm (6,8 po)

PRESSION MAXIMALE : 690 kPa

GAMME DE PRESSION : 414 kPa - 690 kPa

Échappement ajustable

Verrou de gâchette

Loquet

Bouton

(autre

côté)

Gâchette

Chargeur

Endroit de chargement des clous

 

 

Plaque de longueur

Endroit d’expulsion

de clou automatique

des clous

 

2-Fr