Campbell Hausfeld CHN10310 User Manual

Size:
11.81 Mb
Download

See Warranty on page 8 for important information about commercial use of this product.

Operating Instructions

CHN10302, CHN10310

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

Narrow Crown Stapler

Table of Contents

Description . . . . . . . . . . . 1 Unpacking . . . . . . . . . . . 1 Safety Guidelines . . . . . . . . 1 Important Safety Information . . . 1

Tool Components and

Specifications . . . . . . . . . . 2 Operating Instructions . . . . . . 4 Lubrication . . . . . . . . . . 4 Recommended Hookup . . . . . 4 Operational Mode . . . . . . . 5 Single Sequential Mode . . . . . 5 Operating a Sequential Trip Tool . 5 Loading/Unloading The Tool . . . 5 Adjusting the Nail Penetration . . 5

Adjusting the Direction

of the Exhaust . . . . . . . . . 5 User-MaintenanceInstructions . . . 6 Clearing A Jam From The Tool . . 6 Technical Service . . . . . . . . 6 Fastener And Replacement Parts . 6 Tool Repair . . . . . . . . . . 6 Assembly Procedure For Seals . . 6

Fastener and Interchange

Information . . . . . . . . . . 6 Troubleshooting Chart . . . . . . . . . . . . 7 Warranty . . . . . . . . . . . . 8

Description

This stapler is designed for cabinetry, casebacks, decorative trim and crafts. Features include: no-martip, adjustable exhaust, single sequential trigger, quick clear nose, and an adjustable depth of drive mechanism.

Unpacking

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Make sure to tighten fittings, bolts, etc., before putting unit into service.

Safety Guidelines

This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help

recognize this information, observe the following symbols.

Danger indicates an imminently

hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially

hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially

hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates important

information, that if not followed, may cause damage to equipment.

NOTE: Information that requires special attention.

Models CHN10302, CHN10310

Locate model and date code on tool and record below:

Model No.: _____________________

Date Code: _____________________

Retain these numbers for future reference.

California proposition 65

This product or

its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

When using tools, basic precautions should always be followed, including

the following:

You can create dust when you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American IN700502AV 3/10 National Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA

SNT-101-2002.

© 2010 Campbell Hausfeld/Scott Fetzer

For parts, product & service information

visit www.chpower.com

 

Operating Instructions

 

 

 

CHN10302, CHN10310

 

 

 

 

 

 

 

 

 

 

 

 

 

Important Safety Instructions

c.

Keep bystanders, children, and

e.

Use safety equipment. A dust mask,

(Continued)

 

visitors away while operating the

 

non-skidsafety shoes and a hard

General

 

tool. Distractions are able to result in

 

hat must be used for the applicable

 

the loss of control of the tool.

 

conditions.

a.

To reduce the risks of

 

 

 

 

 

 

f.

Always wear eye

 

 

electric shock, fire, and

 

Personal Safety

 

 

injury to persons, read all

 

a.

Stay alert. Watch what you are

 

protection.

 

 

 

 

 

 

 

 

 

 

 

the instructions before

 

g.

Always wear hearing

 

 

 

 

doing and use common sense

 

 

 

 

 

using the tool.

 

 

protection when using

 

 

 

when operating the tool. Do not

 

 

 

 

 

 

b. Be thoroughly familiar with the

 

use the tool while tired or under

 

the tool. Prolonged

 

 

controls and the proper use of the

 

the influence of drugs, alcohol,

 

exposure to high intensity

 

 

equipment. Follow all instructions.

 

or medication. A moment of

 

noise is able to cause

 

 

Contact your Campbell Hausfeld

 

inattention while operating the

 

hearing loss.

 

 

 

 

 

 

representative if you have any

 

tool increases the risk of injury to

h.

Do not attach the hose or tool to

 

questions.

 

persons.

 

your body. Attach the hose to the

c.

Only persons well acquainted with

b.

Dress properly. Do not wear loose

 

structure to reduce the risk of loss of

 

these rules of safe operation should

 

clothing or jewelry. Contain long

 

balance if the hose shifts.

 

be allowed to use the unit.

 

hair. Keep hair, clothing, and

i.

Always assume that the tool

 

 

Read and

 

gloves away from moving parts.

 

contains fasteners. Do not point

 

 

 

 

 

 

understand tool

 

Loose clothes, jewelry, or long

 

the tool toward yourself or anyone

 

 

 

 

labels and manual. Failure to follow

 

hair increases the risk of injury to

 

whether it contains fasteners or not.

warnings, dangers, and cautions could

 

 

 

persons as a result of being caught

j.

 

 

 

 

Do not nail on

result in DEATH or SERIOUS INJURY.

 

 

 

 

 

 

in moving parts.

 

 

 

 

Work Area

 

 

 

 

 

 

top of another

 

 

 

 

 

 

c.

Avoid unintentional starting.

 

nail. This is able to cause the nail to

 

 

 

 

 

be deflected and hit someone, or

a.

Keep the work area clean and well

 

Be sure the switch is off before

 

 

 

cause the tool to react and result in a

 

lighted. Cluttered benches and dark

 

connecting to the air supply. Do not

 

 

 

 

risk of injury to persons.

 

areas increase the risks of electric

 

carry the tool with your finger on

k.

 

 

 

 

Remove finger

 

shock, fire, and injury to persons.

 

the switch or connect the tool to the

 

 

 

 

 

 

 

 

 

 

 

from the trigger

 

 

 

 

 

 

 

 

 

 

 

 

air supply with the switch on.

 

 

 

 

 

b. Do not operate the tool

 

 

 

when not driving fasteners. Never

 

 

 

 

in explosive atmospheres,

 

d.

Do not overreach. Keep proper

 

carry the tool with finger on trigger,

 

such as in the presence

 

 

footing and balance at all times.

 

the tool is able to fire a fastener.

 

of flammable liquids,

 

 

Proper footing and balance enables

 

 

 

 

Always remain in a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

gases, or dust. The tool is

 

better control of the tool in

 

 

 

 

firmly balanced

 

 

position when using or handling the

 

able to create sparks resulting in the

 

unexpected situations.

 

 

tool.

 

ignition of the dust or fumes.

 

 

 

 

 

 

 

 

 

Avoid long extended

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

periods of work

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

with the tool. Stop using the tool if you

 

 

 

 

 

 

feel pain in hands or arms.

Tool Components and Specifications

Requires: 0.3 SCFM with 10 nails per minute @ 90 psi

Air inlet: 1/4 inch NPT

nail SIZE RANGE:

3/8 inch to 1-1/4inch

MAGAZINE CAPACITY:

100 Staples per load, 18 gauge

WEIGHT: 2 lbs. 15 oz.

LENGTH: 10-1/2inches

HEIGHT: 9-1/2inches

MAXIMUM PRESSURE:

100 psi

PRESSURE RANGE:

60 psi – 100 psi

Work Contact

 

Quick Clear Nose

Element (WCE)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fastener

Discharge

Area Area

LoadingFastener

Magazine

Latch

Cap Exhaust

Trigger

Air

Inlet

www.chpower.com

2

Operating Instructions

 

CHN10302, CHN10310

Important Safety Instructions

Never use

Always assume

(Continued)

gasoline

the tool contains

or other flammable liquids

fasteners. Respect the tool as a working

Tool Use and Care

to clean the tool. Never use

implement; no horseplay. Always keep

a.

Use clamps or another practical way

the tool in the presence of

others at a safe distance from the work

 

to secure and support the workpiece

flammable liquids or gases. Vapors

area in case of accidental discharge of

 

could ignite by a spark and cause an

fasteners. Do not point the tool toward

 

to a stable platform. Holding the

 

yourself or anyone whether it contains

 

explosion which will result in death or

 

work by hand or against the body is

fasteners or not. Accidental triggering

 

serious personal injury.

 

unstable and is able to lead to loss

Do not

of the tool could result in death or

 

serious personal injury.

 

of control.

remove,

 

Do not

 

 

tamper with, or otherwise

b. Do not force the tool.Use the

drive a

cause the trigger lock

 

correct tool for the application. The

fastener on top of other

 

or trigger to become

 

fasteners. The fastener

 

correct tool will do the job better

inoperable. Do not operate

 

could glance and cause

 

and safer at the rate for which the

any tool which has been modified in a

 

death or a serious puncture

 

tool is designed.

like fashion. Death or serious personal

wound.

 

injury could result.

c.

Do not use the tool if the switch

 

Do

! WARNING

 

does not turn the tool on or off. Any

not

Do not operate or allow

 

tool that cannot be controlled with

touch the trigger unless

 

anyone else to operate

 

the switch is dangerous and must be

driving fasteners. Never

the tool if any warnings

 

repaired.

attach air line to tool or

or warning labels are not legible.

 

carry tool while touching the trigger.

Warnings or warning labels are located

d.

 

Disconnect the

The tool could eject a fastener which

on the tool magazine and body.

 

tool from the air

will result in death or serious personal

Do not drop or

 

source before making adjustments,

injury. Also actuate the trigger lock to

 

throw the tool.

 

doing tool maintenance, clearing

the safe position when not in use.

 

Dropping or throwing the tool can

 

jams, leaving work area,loading,

 

 

 

result in damage that will make the tool

 

or unloading the tool. Such

 

 

 

unusable or unsafe. If the tool has been

 

precautionary measures reduce the

Always disconnect the

dropped or thrown, examine the tool

 

risk of injury to persons.

tool from the power

closely for bent, cracked or broken parts

e.

Store the tool when it is idle out

source when unattended,

and air leaks. STOP and repair before

performing any maintenance or repair,

using or serious injury could occur.

 

of reach of children and other

 

clearing a jam, or moving the tool to a

Avoid using the

 

untrained persons. A tool is

new location. Do not load the tool with

 

tool when the

 

dangerous in the hands of untrained

fasteners when the trigger is depressed.

 

magazine is empty. Accelerated wear on

 

The tool could eject a fastener causing

 

users.

the tool may occur.

 

death or serious personal injury.

 

 

Clean and check all

f.

Maintain the tool with care. Keep

Always

air supply hoses

 

a cutting tool sharp and clean. A

fit tool

 

and fittings before connecting the

 

properly maintained tool, with sharp

with a fitting or hose

 

tool to an air supply. Replace any

 

coupling on or near the tool

 

cutting edges reduces the risk of

damaged or worn hoses or fittings.

 

in such a manner that all

 

binding and is easier to control.

compressed air in the tool

Tool performance or durability may be

g.

Check for misalignment or binding

is discharged at the time the fitting or

reduced.

hose coupling is disconnected. Do not

Service

 

of moving parts, breakage of parts,

 

use a check valve or any other fitting

 

 

 

and any other condition that affects

which allows air to remain in the tool.

a. Tool service must be performed only

 

the tool’s operation. If damaged,

Death or serious personal injury could

by qualified repair personnel.

 

occur.

 

have the tool serviced before using.

b. When servicing a tool, use only

 

 

 

Many accidents are caused by poorly

 

identical replacement parts. Use

 

maintained tools. There is a risk of

Never place hands or any

only authorized parts.

 

bursting if the tool is damaged.

other body parts in the

c. Use only the lubricants supplied

 

 

fastener discharge area of

h.

Use only those fasteners listed

with the tool or specified by the

the tool. The tool might eject a fastener

 

in the Accessories section of this

and could result in death or serious

manufacturer.

 

manual. Fasteners not identified

personal injury.

Do not make any

 

for use with this tool by the tool

Never

modifications to

 

manufacturer are able to result in

carry the

the tool without first obtaining written

 

tool by the air hose or pull

approval from Campbell Hausfeld. Do

 

a risk of injury to persons or tool

 

the hose to move the tool

 

not use the tool if any shields or guards

 

damage when used in this tool.

or a compressor. Keep hoses

 

are removed or altered. Do not use the

 

 

away from heat, oil and

i.

Selecting an appropriate tool

tool as a hammer. Personal injury or

sharp edges. Replace any

 

actuation system, taking into

tool damage may occur.

 

hose that is damaged, weak

 

Disconnect air

 

consideration the work application

or worn. Personal injury or tool damage

 

supply and release

 

for which the tool is used.

could occur.

 

 

tension from the pusher before

 

 

 

 

 

 

attempting to clear jams because

 

 

 

fasteners can be ejected from the front

 

 

 

of the tool. Personal injury may occur.

 

 

3

www.chpower.com

Operating Instructions

 

 

 

 

CHN10302, CHN10310

Important Safety Instructions

Operating Instructions

 

Recommended Hookup

 

(Continued)

 

Lubrication

 

The illustration below shows the

 

Air Source

 

 

recommended hookup for the tool.

 

This tool requires lubrication before

a. Never connect to an air source that

1.

The air compressor

 

using the tool for the first time and

60 psi

is capable of exceeding 200 psi.

 

must be able to

Min.

before each use. If an inline oiler is

 

Over pressurizing the tool is able

 

maintain a minimum

100 psi

used, manual lubrication through the

 

to result in bursting, abnormal

 

of 60 psi when the

Max.

air inlet is not required on a daily basis.

 

 

operation, breakage of the tool or

 

tool is being used. An inadequate air

The work surface

 

serious injury to persons. Use only

 

supply can cause a loss of power and

can become

 

 

clean, dry, regulated compressed air

 

 

inconsistent driving.

 

damaged by excessive lubrication.

 

 

at the rated pressure or within the

Proper lubrication is the owner’s

2. An oiler can be

 

rated pressure range as marked on

responsibility. Failure to lubricate the

 

 

used to provide oil

 

the tool. Always verify prior to using

tool properly will dramatically shorten

 

 

 

circulation through

 

the tool that the air source has been

the life of the tool and void your

 

 

 

the tool. A filter can

 

warranty.

 

 

 

adjusted to the rated air pressure or

 

 

 

1. Disconnect the air

 

 

be used to remove liquid and solid

within the rated air-pressurerange.

 

 

 

 

impurities which can rust or “gum

supply from the tool

 

 

b. Never use oxygen, carbon dioxide,

 

 

 

 

up” internal parts of the tool.

 

to add lubricant.

 

 

 

combustible gases or any bottled

 

 

 

 

 

 

3. Always use air supply hoses with

gas as an air source for the tool.

 

 

2. Turn the tool so the

 

 

a minimum working pressure

 

Such gases are capable of explosion

OIL

 

 

air inlet is facing up. Place

 

 

rating equal to or greater than the

and serious injury to persons.

 

 

4-5drops of 30 W non-

 

 

pressure from the power source if a

Do not

 

 

 

 

detergent oil into air inlet.

 

 

regulator fails, or 150 psi, whichever

use any

 

 

 

 

Do not use detergent

 

 

is greater. Use 1/4 inch air hose for

type of reactive gases,

O CO2

 

 

including, but not limited

 

oils, oil additives, or airtool oils.

 

runs up to 50 feet. Use 3/8 inch or

to, oxygen and combustible

 

Air tool oils contain solvents which

 

greater air hoses for 50 foot run

gases, as a power source. Use filtered,

will damage the tool's internal

 

or longer. For better performance,

lubricated, regulated compressed air

components.

 

 

install a 3/8 inch quick plug (1/4 inch

only. Use of a reactive gas instead of

 

 

3. After adding oil, run

 

 

NPT threads) with an inside diameter

compressed air may cause the tool

 

 

 

 

of .315 inch (8mm) on the tool and

to explode which will cause death or

tool briefly. Wipe off

 

 

serious personal injury.

 

any excess oil from

 

 

a 3/8 inch quick coupler on the air

Use

 

 

 

hose.

 

 

the cap exhaust.

 

 

 

only a

 

 

 

 

 

 

 

 

 

 

 

pressure-regulated

 

 

 

 

150 psi or greater

 

compressed air source to limit

100 psi

 

 

 

 

 

 

 

 

 

the air pressure supplied to

 

 

 

 

 

 

the tool. The regulated pressure must

 

 

4.

Use a pressure regulator on the

not exceed 100 psi. If the regulator

 

 

 

compressor, with an operating

fails, the pressure delivered to the

 

 

 

 

 

 

pressure of 0 - 125 psi. A pressure

tool must not exceed 200 psi. The tool

 

 

 

 

 

 

regulator is required to control

could explode which will cause death or

 

 

 

serious personal injury.

 

 

 

 

the operating pressure of the tool

Save These Instructions

between 60 and 100 psi.

 

Do Not Discard

 

Recommended Hookup

Quick Plug

Quick Plug (Optional)

Regulator

Quick

 

Quick

Coupler

 

Coupler

 

Air Hose

(Optional)

 

Filter

 

 

 

 

Lubricator

www.chpower.com

4

Operating Instructions

CHN10302, CHN10310

Operating Instructions (Continued)

Operational Mode

Always know the operational mode of

the tool before using. Failure to know the operational mode could result in death or serious personal injury.

Single Sequential Mode

This tool requires the

 

 

trigger to be pulled

 

 

each time a fastener

 

 

is driven. The tool can

1

2

 

 

be actuated by depressing the Work Contact Element (WCE) against the work surface followed by pulling the trigger.

The trigger must be released to reset the tool before another fastener can be driven.

Operating a Sequential Trip Tool

Check the operation of the Work Contact

Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its entire travel distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the tool if the WCE trip mechanism is not operating properly. Personal injury may occur.

1. Disconnect the air supply from the tool.

2.Remove all nails from the magazine (see Loading/ Unloading).

3. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding.

4. Reconnect air supply to the tool.

5. Depress the WCE against the work surface without pulling the trigger. The tool must not

operate. Do not use the tool if it operates without pulling the trigger. Personal injury may result.

6. Remove the tool from

 

 

the work surface.

 

 

The WCE must return

 

 

to its original down

 

 

position. The tool

 

 

must not operate. Do not use

the tool if it operates while lifted

from the work surface. Personal

injury may result.

 

 

7. Pull the trigger

 

 

and depress the

 

 

WCE against the

 

 

work surface. The

1

2

 

 

tool MUST NOT operate.

 

8.

Depress the WCE

 

 

 

against the work

 

 

 

surface. Pull the

1

2

 

trigger. The tool

 

 

 

 

MUST operate.

 

 

An improperly functioning tool

must not be used. Do not actuate the tool unless the tool is placed firmly against the work piece.

Loading / Unloading The Tool

1.Always disconnect the tool from the air supplybefore loading fasteners.

2. Push down on the latch button. Pull back on the magazine cover.

3.Load a clip of fasteners with the crowns straddling the magazine rail.

4.Push the magazine cover forward until latch button pops up.

5.Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, exceptalways disconnect the air hose before unloading.

Adjusting the Nail Penetration

The tool is equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface.

1.Adjust operating pressure so nails are driven consistently. Do not exceed 100 psi.

2.To drive the nail shallower, turn the wheel (C) to right to the extent desired.

(C)

3.To sink a nail deeper, turn the wheel

(C) to left to the extent desired.

4. Make sure trigger and work contact element move freely up and down without binding or sticking after each adjustment.

Adjusting The Direction Of The

Exhaust

The tool is equipped

 

with an adjustable

 

direction exhaust

 

deflector. This is

 

intended to allow

Rotate

the user to change

 

the direction of the exhaust. Simply twist the deflector to any direction desired.

5

www.chpower.com

Operating Instructions

CHN10302, CHN10310

User - Maintenance

7. Extend the wire

Instructions

latch and place

Clearing A Jam From The Tool

over the hooks on

the nose.

1.

Disconnect the air

 

 

supply from the

8. Close the latch by

 

tool.

pushing the latch

 

 

up and in until the

2.

Remove all nails

latch snaps into

place.

 

from the magazine

 

9. Make sure the

 

(see Loading/

 

trigger and work

 

Unloading).

 

contact element

 

 

 

Failure to remove

(WCE) move freely

 

all fasteners will

up and down

cause the fasteners to eject from the

without sticking or binding.

front of the tool.

 

3.

Undo latch by

Technical Service

Please call our Tool Hotline at 1-800-

 

pulling out

 

and down. The

543-6400with any questions regarding

 

wire latch will

the operation or repair of this tool or

 

disengage from

for additional copies of this manual.

 

the hooks on the nose.

Fastener And Replacement

 

 

4.

The door can

Parts

 

now be rotated,

Use only headless

 

exposing the

micropins, 18 gauge.

 

jammed fastener.

Tool performance, safety and durability

 

 

could be reduced if improper fasteners

5.

Remove the

are used. When ordering replacement

parts or fasteners, specify by part

 

jammed fastener,

number.

 

using pliers or

Tool Repair

 

a screwdriver if

 

Only qualified personnel should repair

 

required.

 

the tool and they should use genuine

6.

Rotate door back

Campbell Hausfeld replacement parts

 

into the closed

 

and accessories, or parts and accessories

 

position.

 

which perform equivalently.

 

 

Assembly Procedure For Seals

When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lubeor equivalent must be used on allo-rings.Eacho-ringmust be coated withO-lubebefore assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30Wnon-detergentoil or equivalent, must be added through the air line before testing.

Storage

The tool should be stored in a cool dry place.

Fasteners

The following Campbell Hausfeld finishing nails are available at local retail stores. If you need help locating any item, call customer service at 1-800-543-6400.Campbell Hausfeld nails meet or exceed ASTM Standard F1667.

 

 

Wire

Crown

 

 

 

Nails Per

Nails Per

Model

Length

Diameter

Size

Point

Finish

Collation

Stick

Box

FN180615AV

1/2 inch

18 Gauge

1/4 inch

Chisel

Galvanized / Vinyl Coated

Adhesive

100

1000

FN180620AV

3/4 inch

18 Gauge

1/4 inch

Chisel

Galvanized / Vinyl Coated

Adhesive

100

1000

FN180625AV

1 inch

18 Gauge

1/4 inch

Chisel

Galvanized / Vinyl Coated

Adhesive

100

1000

FN180630AV

1-1/4inch

18 Gauge

1/4 inch

Chisel

Galvanized / Vinyl Coated

Adhesive

100

1000

Interchange Information

Staples used in the Finishing Stapler will also work in: Senco LN4450, SJS-LR,SKSL11-15,Hitachi N3804A, DuofastBN-1832S,KN-1848,Stan-TechSDS18-14,Atro Minor 90/30, 90/32, 90/40, and Porter Cable NS100.

www.chpower.com

6

Operating Instructions

CHN10302, CHN10310

 

 

Troubleshooting Chart

Stop using tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.

Symptom

Possible Cause(s)

Corrective Action

Air leaking at trigger valve

O-ringsin trigger valve housing are

Replace o-ringsand check operation of Work

area.

damaged

Contact Element (WCE)

 

 

 

 

Air leaking between housing

1. Loose screws in housing

1.

Tighten screws

and nose.

2.

Damaged o-rings

2.

Replace o-rings

 

 

3.

Damage to bumper

3.

Replace bumper

 

 

 

 

Air leaking between housing

1. Loose screws

1.

Tighten screws

and cap.

2.

Damaged gasket

2.

Replace gasket

 

 

 

 

 

Tool skips driving fastener

1. Worn bumper

1.

Replace bumper

 

2.

Dirt in nose piece

2.

Clean drive channel

 

3.

Dirt or damage prevent fasteners or

3.

Clean magazine

 

 

pusher from moving freely in magazine

 

 

 

4.

Damaged pusher spring

4.

Replace spring

 

5.

Inadequate air flow to tool

5.

Check fitting, hose, or compressor

 

6.

Worn o-ringson piston or lack of

6.

Replace and lubricate o-rings

 

 

lubrication

 

 

 

7.

Damaged o-ringson trigger valve

7.

Replace o-rings

 

8.

Air leaks

8.

Tighten screws and fittings

 

9.

Cap seal leaking

9.

Replace seal

 

 

 

 

Tool runs slow or has loss of

1. Tool not lubricated sufficiently

1.

Lubricate tool

power

2.

Broken spring in cylinder cap

2.

Replace spring

 

 

3.

Exhaust port in cap is blocked

3.

Replace damaged internal parts

 

 

 

 

Fasteners are jammed in tool

1. Guide on driver is worn

1.

Replace guide

 

2.

Fasteners are not correct size

2.

Use only recommended fasteners

 

3.

Fasteners are bent

3.

Replace with undamaged fasteners

 

4.

Magazine or nose screws are loose

4.

Tighten screws

 

5.

Driver is damaged

5.

Replace driver

 

6.

Fasteners loaded incorrectly

6.

Review Loading / Unloading section in this

 

 

 

 

manual

7

www.chpower.com

Operating Instructions

CHN10302, CHN10310

Limited Warranty

1.DURATION: From the date of purchase by the original purchaser as follows: One (1) Year.

2.WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400

3.WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product.

4.WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This Campbell Hausfeld nailer or stapler.

5.WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the duration of the warranty period with the exceptions below.

6.WHAT IS NOT COVERED UNDER THIS WARRANTY:

A.Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial, industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you.

B.ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

C.Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions shall also include the removal or alteration of any safety devices. If such safety devices are removed or altered, this warranty is void.

D.Normal adjustments which are explained in the owner’s manual(s) provided with the product.

E.Items or service that are normally required to maintain the product, e.g. o-rings,springs, bumpers, debris shield,driver blades, gaskets, packings or seals,lubricants, or any other expendable part not specifically listed. These items will only be covered for ninety (90) days from date of original purchase.Underlined items are warranted for defects in material and workmanship only.

7.RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which are defective, have malfunctioned and/or failed to conform within the duration of the specific warranty period.

8.RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A.Provide dated proof of purchase and maintenance records.

B.Call Campbell Hausfeld (800) 543-6400to obtain your warranty service options. Freight costs must be borne by the purchaser.

C.Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9.WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may also have other rights which vary from state to state or country to country.

www.chpower.com

8

Voir la Garantie à la page 16 pour de l’information importante sur l’utilisation commercial de ce produit.

Instructions d’Utilisation

CHN10302, CHN10310

 

 

S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de procéder à l’entretien du produit décrit. Se protéger ainsi que les autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et/ou dégâts matériels! Conserver ces instructions comme référence.

Agrafeuse de couronnes étroites

Table des matières

Description . . . . . . . . . . . 9 Déballage . . . . . . . . . . . .9 Directives de sécurité . . . . . . . 9

Importantes instructions

de sécurité . . . . . . . . . . . 9

Pièces détachées et fisch technique mécanisme de l'outil . . . . . . .10

Mode d’emploi . . . . . . . . . 12 Graissage . . . . . . . . . . .12 Branchement recommandé . . . 12 Mode d’opération . . . . . . . 13 Mode séquentiel unique . . . . 13 Emploi d'un outil à

déclenchement séquentiel . . . .13 Chargement / Déchargement

de la l'outil . . . . . . . . . .13 Réglage de pénétration des clous .13 Ajustement de la direction d'échappement . . . . . . . . 13

Instructions de maintenance de l'utilisateur . . . . . . . . . . .14

Déblocage de l'outil . . . . . . 14 Support Technique . . . . . . .14 Attaches et Pièces de Rechange . .14 Réparation de l'outil . . . . . . 14 Méthode d’assemblage pour

les joints d’étanchéité . . . . . .14 Attaches et Infornation d'Interchangeabilité . . . . . . .14 Guide de dépannage . . . . . . .15 Garantie limitée . . . . . . . . .16

Description

Cet outil est conçu pour les armoires, les derrières, les décorations et l'artisanat. Caractéristiques: embout ne laissant pas de marque, éjection réglable, gâchette séquentielle unique, buse à dégagement rapide, réglage de pénétration des attaches.

Déballage

Dès que l’appareil est déballé, l’inspecter attentivement pour tout signe de dommages en transit. S’assurer de resserrer tous les raccords, boulons, etc. avant de le mettre en service.

Directives de Sécurité

Ce manuel contient de l’information très importante qui est fournie pour la SÉCURITÉ et pour ÉVITER LES

PROBLÈMES D’ÉQUIPEMENT. Rechercher les symboles suivants pour cette information.

Danger indique une situation

dangereuse imminente qui MÈNERA à la mort ou à des blessures graves si elle n’est pas évitée.

Avertissement indique une

situation potentiellement dangereuse qui, si elle n’est pas évitée, POURRAIT mener à la mort ou à de graves blessures.

Attention indique une

situation potentiellement dangereuse qui, si elle n’est pas évitée, PEUT mener à des blessures mineures ou modérées.

Avis indique

de l’information importante qui pourrait endommager l’équipement si elle n’est pas respectée.

REMARQUE : L’information qui exige une attention spéciale.

Importantes instructions de sécurité

INSTRUCTIONS PORTANT SUR UN RISQUE D’INCENDIE, UN CHOC ÉLECTRIQUE OU DES BLESSURES AUX PERSONNES

En utilisant les outils, il faut suivre

les précautions de base, y compris ce qui suit :

Modéles CHN10302, CHN10310

Trouver le numéro de modèle et le code date sur l’outil et inscrire plus bas :

No du Model: ___________________

Code de date: __________________

Conserver ces numéros comme référence.

PRoposition 65 DE CALIFORNIE

Ce produit ou son cordon peuvent

contenir des produits chimiques qui, de l’avis de l’État de Californie, causent le cancer et des anomalies congénitales ou autres problèmes de reproduction. Lavez-vousles mains après la manipulation.

Vous pouvez

créer de la poussière en coupant, ponçant, perçant

ou meulant les matériaux

tels que le bois, la peinture, le métal, le béton, le ciment ou autre maçonnerie. Cette poussière contient souvent des produits chimiques reconnus pour causer le cancer, les déformations congénitales ou autres problèmes de la reproduction. Porter de l’équipement de protection.

MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie!

Joignez-laà ce manuel ouclassez-ladans un dossier pour plus de sécurité.

Les Cloueuses Campbell Hausfeld conforment aux/ou dépassent les standards de

IN700502AV 3/10

l’American National Standard/International Staple, Nail and Tool Association in

 

ANSI/ISANTA SNT-101-2002.

 

 

© 2010 Campbell Hausfeld/Scott Fetzer

9-Fr

 

Instructions d’Utilisation

 

 

 

CHN10302, CHN10310

 

 

 

 

 

 

 

 

 

 

 

 

 

Importantes instructions

Sécurité personnelle

f.

Toujours porter une

 

 

de sécurité (Suite)

a.

Rester vigilant. Il faut regarder ce

 

protection pour les yeux.

 

Généralité :

 

que vous faites et utiliser son sens

g.

Toujours porter une

 

 

commun en faisant fonctionner

 

protection auditive en

 

a. Pour réduire les risques

 

 

 

 

 

 

 

 

un outil. Ne pas faire fonctionner

 

utilisant l’outil. Toute

 

 

de chocs électriques,

 

 

 

 

 

 

 

 

 

l’appareil si vous êtes fatigué ou

 

exposition prolongée

 

 

d’incendie ou de blessures

 

 

 

 

 

 

 

 

 

sous l’influence de drogues, d’alcool

 

à des bruits de forte

 

 

aux personnes, lire toutes

 

 

 

 

 

 

 

 

 

ou de médicaments. Un moment

 

intensité pourrait

 

 

 

 

 

 

 

 

 

 

les instructions avant

 

 

 

d’inattention en faisant fonctionner

 

provoquer une perte

 

 

d’utiliser l’outil.

 

 

 

 

 

l’outil augmente le risque de

 

auditive.

b. Se familiariser avec ce produit, ses

 

 

 

blessures.

h.

Ne pas attacher le boyau d’air ou

commandes et son utilisation. Suivez

 

b. Il faut s’habiller correctement.

 

l’outil à votre corps. Fixer le boyau

toutes les instructions. Contacter

 

 

Ne pas porter de bijoux ou de

 

à la structure pour réduire le risque

votre représentant Campbell

 

 

 

vêtements amples. Attacher les

 

de perte d’équilibre si le boyau se

Hausfeld si vous avez des questions.

 

 

 

cheveux longs. Garder les cheveux,

 

déplace.

c. Seules les personnes familières avec

 

 

 

les vêtements et les gants loin

i.

Toujours assumer que l’outil

ces règles d’utilisation sans danger

 

 

des pièces mobiles. Les vêtements

 

contient des attaches. Ne pas

devraient utiliser cette unité.

 

 

 

amples, les bijoux ou les cheveux

 

pointer l’outil vers soi ou vers

 

Lire et comprendre

 

 

 

 

longs augmentent le risque de

 

quelqu’un d’autre qu’il y ait des

 

les étiquettes et le

 

blessures si quelque chose se prend

 

attaches ou non.

 

 

 

manuel sur les outils. Ne pas suivre les

 

 

 

dans les pièces mobiles.

j.

 

 

 

 

 

 

 

avertissements, les dangers et les mises

 

 

 

 

 

Ne pas clouer

c.

Éviter tout démarrage accidentel.

 

 

 

 

en garde pourrait causer la MORT ou de

 

 

 

 

 

sur le dessus

 

 

 

 

 

 

S’assurer que l’interrupteur est

 

 

 

 

 

GRAVES BLESSURES.

 

 

d’un autre clou. Ceci pourrait faire

Aire de travail

 

en position d’arrêt (off) avant de

 

dévier le clou qui pourrait alors

 

brancher à l’alimentation d’air.

 

frapper quelqu’un ou l’outil pourrait

a. Garder l’aire de travail propre et

 

Ne pas transporter l’outil avec le

 

réagir provoquant des blessures.

bien éclairée. Les établis encombrés

 

doigt sur l’interrupteur ni brancher

k.

 

 

 

 

Retirer le doigt

 

 

 

 

 

et les coins sombres augmentent

 

l’outil à l’alimentation d’air avec

 

 

 

 

 

de la gâchette

 

 

 

 

 

 

les risques de chocs électriques,

 

l’interrupteur en marche.

 

lorsqu’on n’enfonce pas d’attaches.

d’incendie et de blessures aux

d.

Ne pas trop se pencher. Garder bon

 

Ne jamais transporter l’outil avec

personnes.

 

le doigt sur la gâchette car l’outil

 

pied et bon équilibre en tout temps.

 

b. Ne pas faire fonctionner

 

 

 

Ceci permet d’avoir un meilleur

 

pourrait déclencher l’attache.

l’outil dans une

 

 

 

contrôle de l’outil dans les situations

 

 

 

 

Toujours bien

 

 

 

 

 

atmosphère explosive

 

 

 

imprévues.

 

 

 

 

s’équilibrer

 

 

 

 

 

comme en présence

 

 

e.

Utiliser l’équipement de sécurité.

pendant la manipulation ou l’utilisation

de liquides, gaz

de l'outil.

 

Il faut utiliser un masque

ou poussières inflammables.

 

 

 

 

 

Éviter d’utiliser

 

antipoussières, des souliers de

 

 

 

 

L’outil peut produire des étincelles

 

 

 

 

 

l'outil pour une

 

sécurité antidérapants et un casque

 

 

 

 

 

 

 

 

 

menant à une inflammation de

 

période de temps prolongée. Cesser

 

de protection appropriés pour les

 

d’utiliser l'outil si l’on ressent des

poussières ou de fumées.

 

 

conditions en cours.

 

douleurs dans les mains ou dans les

c. Garder les spectateurs, les enfants et

 

 

 

bras.

les visiteurs loin en utilisant l’outil.

Les distractions peuvent faire perdre le contrôle de l’outil.

Pièces détachées et fiche technique mécanisme de la l'outil

EXIGE : 0,01 m3/min avec 10 une attaches par minute à 621 kPa

PRISE D’AIR : 1/4 po NPT

TAILLES DES Clous :

3/8 po à 1-1/4po

CAPACITÉ DU CHARGEUR :

100 clous par charge, calibre 18

POIDS : 1,33 kg

LONGUEUR : 26,67 cm(10-1/2po)

HAUTEUR : 24,13 cm(9-1/2po)

PRESSION MAXIMALE : 690 kPa

GAMME DE PRESSION :

414 kPa – 690 kPa

Mécanisme de

 

 

 

Buse à dégagement

déclenchement par contact

 

 

 

rapide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Endroit

attaches

 

d’expulsion

 

des attaches

de chargement des

 

Chapeau d'échappement

Gâchette

Arrivée

d’air

Endroit

Chargeur

 

 

Loquet

10-Fr