SmartSwitch 9000 9E132-15, 9E133-36 9E138-12 & 9E138-36 User’s Guide
9031173-02
Notice
Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
© Copyright April 1998 by:
Cabletron Systems, Inc.
35 Industrial Way
Rochester, NH 03867-5005
All Rights Reserved
Printed in the United States of America
Order Number: 9031173-02
LANVIEW is a registered trademark, and SmartSwitch is a trademark of Cabletron Systems, Inc.
CompuServe is a registered trademark of CompuServe, Inc.
i960 microprocessor is a registered trademark of Intel Corp.
Ethernet is a trademark of Xerox Corporation.
i
Notice
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
VCCI Notice
This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
DOC Notice
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
ii
Notice
DECLARATION OF CONFORMITY
ADDENDUM
Application of Council Directive(s): |
89/336/EEC |
|
73/23/EEC |
Manufacturer’s Name: |
Cabletron Systems, Inc. |
Manufacturer’s Address: |
35 Industrial Way |
|
PO Box 5005 |
|
Rochester, NH 03867 |
European Representative Name: |
Mr. J. Solari |
European Representative Address: |
Cabletron Systems Limited |
|
Nexus House, Newbury Business Park |
|
London Road, Newbury |
|
Berkshire RG13 2PZ, England |
Conformance to Directive(s)/Product Standards: |
EC Directive 89/336/EEC |
|
EC Directive 73/23/EEC |
|
EN 55022 |
|
EN 50082-1 |
|
EN 60950 |
Equipment Type/Environment: |
Networking Equipment, for use in a |
|
Commercial or Light |
|
Industrial Environment. |
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this notice conforms to the above directives.
Manufacturer |
Legal Representative in Europe |
Mr. Ronald Fotino |
Mr. J. Solari |
____________________________________________________ |
______________________________________________________ |
Full Name |
Full Name |
Principal Compliance Engineer |
Managing Director - E.M.E.A. |
____________________________________________________ |
______________________________________________________ |
Title |
Title |
Rochester, NH, USA |
Newbury, Berkshire, England |
____________________________________________________ |
______________________________________________________ |
Location |
Location |
iii
Notice
iv
Chapter 1 |
Introduction |
|
|
Features........................................................................................................................... |
1-1 |
|
Related Manuals............................................................................................................ |
1-4 |
|
Getting Help .................................................................................................................. |
1-4 |
Chapter 2 |
Installing the Modules |
|
|
Installing EPIMs ............................................................................................................ |
2-3 |
|
EPIM Revisions ...................................................................................................... |
2-3 |
|
Installing the EPIM ................................................................................................ |
2-4 |
|
The Reset Switch ........................................................................................................... |
2-5 |
|
User-Accessible Components...................................................................................... |
2-6 |
|
Setting the Module Card DIP Switch ......................................................................... |
2-7 |
Chapter 3 |
Operation |
|
|
Flexible Network Bus (FNB)........................................................................................ |
3-2 |
|
System Management Buses ......................................................................................... |
3-2 |
|
SMB-1 Bus ............................................................................................................... |
3-2 |
|
SMB-10 Bus ............................................................................................................. |
3-2 |
|
System Diagnostic Controller...................................................................................... |
3-3 |
|
DC/DC Converter ........................................................................................................ |
3-3 |
|
FNB Interface ................................................................................................................. |
3-3 |
|
i960 Core......................................................................................................................... |
3-4 |
Chapter 4 |
LANVIEW LEDs |
|
Chapter 5 |
Specifications |
|
|
Safety............................................................................................................................... |
5-1 |
|
Service............................................................................................................................. |
5-1 |
|
Physical........................................................................................................................... |
5-2 |
|
Dimensions ............................................................................................................. |
5-2 |
|
Weight...................................................................................................................... |
5-2 |
|
Environment ........................................................................................................... |
5-2 |
v
Contents
Appendix A EPIMs
EPIM-T........................................................................................................................... |
A-1 |
EPIM-F1 and EPIM-F2................................................................................................. |
A-2 |
EPIM-F3 ......................................................................................................................... |
A-3 |
EPIM-C........................................................................................................................... |
A-5 |
Connector Type ..................................................................................................... |
A-5 |
Grounding.............................................................................................................. |
A-5 |
EPIM-A and EPIM-X (AUI Port) ................................................................................ |
A-5 |
vi
Chapter 1
The 9E132-15, 9E133-36, 9E138-12, and 9E138-36 MicroLAN™ Switch Modules, shown in Figure 1-1, are four channel Ethernet bridges and routers. Up to three front panel Ethernet networks can be connected to this module and they can be bridged/routed to any other Ethernet segment and to any other SmartSwitch 9000 module via the FNB bus (acting as the fourth port).
NOTE |
The 9E132-15, 9E133-36, 9E138-12, and 9E138-36 MicroLAN™ Modules will be referred to collectively as the Ethernet MicroLan Modules.
Processor
The Ethernet MicroLan Switch Modules are equipped with an advanced Intel i960 microprocessor. This microprocessor provides a platform for all management functions within a scalable RISC-based architecture.
System Management
The Ethernet MicroLan Switch Modules provide interfaces to the two System Management Buses (SMB-1 and SMB-10) for intermodule management.
Connectivity
The 9E132-15 provides four RJ-45 ports and one EPIM slot for each of the three channels. See Chapter 5 for information on the use of EPIMs.
The 9E133-36 has one 50-pin front panel for each of the three channels, providing 12 individual Ethernet connections each.
The 9E138-12 provides four ST-type multi-mode fiber optic connections for each of the three channels, for a total of 12 connections.
1-1
Introduction
NOTE |
The 9E138-36 provides 12 ST-type multi-mode fiber optic connections for each of the three channels, for a total of 36 connections.
All ports function as repeaters for incoming data which retime and retransmit all packets.
Bridging/Routing
The Ethernet MicroLan Switch Modules provide Bridging/Routing between the front panel channels and/or to any other module in the chassis via FNB -1 or FNB -2 of the FNB bus. IEEE 802.1d Spanning Tree Protocol is supported in all bridging functions.
Management Information Base (MIB) Support
All concentrator modules provide MIB support including the following:
•IETF FDDI MIB
•IETF MIB II
•Cabletron Enterprise MIBs
For a complete list of supported MIBs, refer to the release notes provided in the module package.
RMON
RMON support (RFC1271).
LANVIEW LEDs
The Ethernet MicroLan Switch Modules use LANVIEW: the Cabletron Systems built-in visual diagnostic and status monitoring system. With LANVIEW LEDs, you can quickly identify the device, port, and physical layer status at a glance.
Hot Swapping
The Ethernet MicroLan Switch Modules can be installed or removed from the chassis while the SmartSwitch 9000 is powered up without affecting the operation of the remaining modules in the chassis.
1-2
Introduction
ETHERNET |
ETHERNET |
ETHERNET |
ETHERNET |
|
|
|
|||||||||
9E132-15 |
9E133-36 |
9E138-12 |
9E138-36 |
|
|
|
|||||||||
SMB |
|
CPU |
SMB |
|
CPU |
SMB |
|
CPU |
SMB |
|
|
CPU |
|
|
|
FNB |
|
|
FNB |
|
|
FNB |
|
|
FNB |
|
|
|
|
|
|
1 |
2 |
3 |
1 |
2 |
3 |
1 |
2 |
3 |
|
|
|
|
|
|
|
|
|
|
1 |
2 |
|
3 |
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
1 |
|
|
1 |
|
|
ENET 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ENET 1 |
|
ENET 1 |
|
|
ENET 1 |
||||
2 |
|
|
|
|
|
1 |
|
3 |
|
|
|
||||
|
|
2 |
|
|
|
1 |
|
3 |
5 |
7 |
9 |
11 |
|||
|
|
|
|
|
|
|
|
|
|||||||
3 |
|
|
3 |
|
|
2 |
|
4 |
2 |
|
4 |
6 |
8 |
10 |
12 |
|
|
|
|
|
|
|
|
|
|||||||
4 |
|
|
4 |
|
|
ENET 2 |
|
ENET 2 |
|
ENET 2 |
|
|
ENET 2 |
||
|
|
|
|
|
1 |
|
3 |
|
|
|
|||||
5 |
|
|
|
|
|
|
1 |
|
3 |
5 |
7 |
9 |
11 |
||
|
|
5 |
|
|
|
|
|
|
|||||||
|
|
|
|
|
2 |
|
4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
4 |
6 |
8 |
10 |
12 |
||
|
|
|
6 |
|
|
|
|
|
|
||||||
|
|
|
|
|
|
ENET 3 |
|
ENET 3 |
|
ENET 3 |
|
|
ENET 3 |
||
|
|
|
7 |
|
|
1 |
|
3 |
|
|
|
||||
|
|
|
|
|
|
1 |
|
3 |
5 |
7 |
9 |
11 |
|||
|
|
|
8 |
|
|
2 |
|
4 |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
9 |
|
|
|
|
|
2 |
|
4 |
6 |
8 |
10 |
12 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10 |
|
|
ETHERNET 1 |
|
|
|
ETHERNET 1 |
|
||||
|
|
|
11 |
|
|
RX |
|
|
RX |
|
|
RX |
|
|
RX |
|
|
|
12 |
|
|
|
|
|
|
|
|
|
|
|
|
E
T
H
E
R
N |
2X |
E |
E |
|
T |
T |
|
H |
|
3X |
E |
1 |
|
R |
|
4X |
N |
|
E |
T
5X |
1 |
|
1 |
1 |
5 |
9 |
12 |
|
|
|
TX |
TX |
TX |
TX |
RX |
RX |
RX |
RX |
2 |
2 |
6 |
10 |
TX |
TX |
TX |
TX |
RX |
RX |
RX |
RX |
3 |
3 |
7 |
11 |
TX |
TX |
TX |
TX |
RX |
RX |
RX |
RX |
4 |
4 |
8 |
12 |
|
|
|
TX |
TX |
TX |
TX |
|
|
1 |
|
|
|
|
|
|
|
ETHERNET 2 |
|
ETHERNET 2 |
|
|
|
|
RX |
RX |
RX |
RX |
|
|
12 |
1 |
1 |
5 |
9 |
E |
|
|
TX |
TX |
TX |
TX |
T |
|
|
|
|
|
|
H |
|
E |
RX |
RX |
RX |
RX |
E |
|
2 |
2 |
6 |
10 |
|
|
T |
|||||
R |
|
|||||
2X |
H |
|
|
|
|
|
N |
TX |
TX |
TX |
TX |
||
E |
|
E |
|
|
|
|
T |
|
R |
RX |
RX |
RX |
RX |
|
3X |
N |
|
|
|
|
2 |
|
E |
3 |
3 |
7 |
11 |
|
4X |
T |
TX |
TX |
TX |
TX |
|
2 |
|
|
|
|
|
|
|
RX |
RX |
RX |
RX |
|
|
5X |
|
4 |
4 |
8 |
12 |
|
|
1 |
TX |
TX |
TX |
TX |
|
|
|
|
|
|
|
|
|
|
ETHERNET 3 |
|
ETHERNET 3 |
|
|
|
|
RX |
RX |
RX |
RX |
|
|
12 |
1 |
1 |
5 |
9 |
|
|
|
||||
E |
|
|
TX |
TX |
TX |
TX |
|
E |
|
|
|
|
|
T |
|
RX |
RX |
RX |
RX |
|
H |
|
T |
2 |
2 |
6 |
10 |
E |
|
H |
||||
R |
2X |
E |
TX |
TX |
TX |
TX |
N |
R |
|
|
|
|
|
E |
|
N |
RX |
RX |
RX |
RX |
T |
3X |
E |
3 |
3 |
7 |
11 |
3 |
T |
|||||
|
3 |
TX |
TX |
TX |
TX |
|
|
|
|||||
|
4X |
|
|
|
|
|
|
|
RX |
RX |
RX |
RX |
|
|
5X |
|
4 |
4 |
8 |
12 |
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TX |
TX |
TX |
TX |
Figure 1-1. The Ethernet MicroLan Switch Modules
1-3