- •1.1 Using This Guide
- •1.2 Structure of This Guide
- •1.3.1 Connectivity
- •1.3.2 Full Duplex Switched Ethernet
- •1.3.3 SmartTRUNK
- •1.3.4 Management
- •1.3.5 Switching Options
- •1.3.6 Standards Compatibility
- •1.3.7 LANVIEW Diagnostic LEDs
- •1.3.8 Year 2000 Compliant
- •1.3.9 Runtime IP Address Discovery
- •1.3.10 Local Management Features
- •1.4 Optional Features
- •1.5 Document Conventions
- •1.6 Getting Help
- •1.7 Related Manuals
- •Network Requirements
- •2.1 SmartTrunk
- •3.1 Required Tools
- •3.5 Connecting to the Network
- •3.6 Completing the Installation
- •4.1 Using LANVIEW
- •4.3 Troubleshooting Checklist
- •4.4 Using the RESET Button
- •Local Management
- •5.1 Overview
- •5.2 Local Management Keyboard Conventions
- •5.3 Management Terminal Setup
- •5.3.1 Console Cable Connection
- •5.3.2 Connecting an Uninterruptible Power Supply (UPS)
- •5.3.3 Management Terminal Setup Parameters
- •5.3.4 Telnet Connections
- •5.4 Accessing Local Management
- •5.4.1 Navigating Local Management Screens
- •5.4.2 Selecting Local Management Menu Screen Items
- •5.4.3 Exiting Local Management Screens
- •5.5 The Main Menu Screen
- •5.6 Chassis Menu Screen
- •5.7 Chassis Configuration Screen
- •5.7.1 Setting the IP Address
- •5.7.2 Setting the Subnet Mask
- •5.7.3 Setting the Chassis Date
- •5.7.4 Setting the Chassis Time
- •5.7.5 Entering a New Screen Refresh Time
- •5.7.6 Setting the Screen Lockout Time
- •5.7.7 Setting the Operational Mode
- •5.8 SNMP Community Names Screen
- •5.8.1 Establishing Community Names
- •5.9 SNMP Traps Screen
- •5.10 Chassis Environmental Screen
- •5.11 Port Redirect Function Screen
- •5.11.1 Displaying the Source and Destination Entries
- •5.11.2 Changing Source and Destination Ports
- •5.12 Module Selection Screen
- •5.12.1 Selecting a Module
- •5.13 Module Menu Screen
- •5.14 Module Configuration Menu Screen
- •5.15 General Configuration Screen
- •5.15.1 Setting the IP Address
- •5.15.2 Setting the Subnet Mask
- •5.15.3 Setting the Default Gateway
- •5.15.4 Setting the TFTP Gateway IP Address
- •5.15.5 Setting the Module Date
- •5.15.6 Setting the Module Time
- •5.15.7 Entering a New Screen Refresh Time
- •5.15.8 Setting the Screen Lockout Time
- •5.15.9 Setting the Operational Mode
- •5.15.10 Setting the Management Mode
- •5.15.12 Changing the Com Port Application
- •5.15.13 Clearing NVRAM
- •5.15.14 Enabling/Disabling IP Fragmentation
- •5.16 SNMP Community Names Screen
- •5.16.1 Establishing Community Names
- •5.17 SNMP Traps Screen
- •5.18 Switch Configuration Screen
- •5.18.1 Setting the STA
- •5.18.2 Setting the Age Time
- •5.18.3 Setting (Enabling or Disabling) the Port Status
- •5.19 Ethernet Full Duplex Configuration Screen
- •5.19.1 Setting the Operation Mode
- •5.20 Module Specific Configuration Menu Screen
- •5.21 System Resources Screen
- •5.21.1 Setting the Reset Peak Utilization
- •5.22.4 Setting the FE-100TX Operational Mode
- •5.22.5 Setting the FE-100TX Advertised Ability
- •5.23 Flash Download Screen
- •5.23.1 Image File Download Using TFTP
- •5.23.2 Image File Download Using RUNTIME
- •5.23.3 Image File Download Using BootP
- •5.24 Port Redirect Function Screen
- •5.24.1 Displaying the Source and Destination Entries
- •5.24.2 Changing Source and Destination Ports
- •5.25 Broadcast Suppression Screen
- •5.25.1 Setting the Threshold
- •5.25.2 Setting the Reset Peak Switch
- •5.26 Module Statistics Menu Screen
- •5.27 Switch Statistics Screen
- •5.27.1 Using the Clear Counters Command
- •5.28 The Interface Statistics Screen
- •5.28.1 Displaying Interface Statistics
- •5.28.2 Using the Clear Counters Command
- •5.29 RMON Statistics Screen
- •5.29.1 Displaying RMON Statistics
- •5.29.2 Using the Clear Counters Command
- •5.30 Network Tools
- •5.30.1 Built-in Commands
- •5.30.2 Special Commands
- •A.1 Device Specifications
- •A.2 Physical Properties
- •A.3 Environmental Requirements
- •A.4 Input/Output Ports
- •A.5 COM Port Pinout Assignments
- •A.6 Regulatory Compliance
- •B.1 FE-100TX
- •B.2 FE-100FX
- •B.3 FE-100F3
- •C.1 Required Tools
- •C.2 Setting the Mode Switch
- •C.3 Installing Optional Fast Ethernet Interface Modules
Cabletron Systems reserves the right to make changes in speciﬁcations and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.
The hardware, ﬁrmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
1998 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH
Printed in the United States of America
Cabletron Systems is a registered trademark andSmartSwitch is a trademark of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.
WARNING: Changes or modiﬁcations made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT
IMPORTANT: Before utilizing this product, carefully read this License Agreement.
This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron software program (the “Program”) contained in this package. The Program may be contained in ﬁrmware, chips or other media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.
CABLETRON SOFTWARE PROGRAM LICENSE
1.LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as authorized in writing by Cabletron.
2.OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3.APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.
EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY
1.EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
2.NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS
The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer software” submitted with restricted rights in accordance with Section
For Department of Defense units, the product is licensed with “Restricted Rights” as deﬁned in the DoD Supplement to the Federal Acquisition Regulations, Section
DECLARATION OF CONFORMITY
Application of Council Directive(s): 89/336/EEC
Manufacturer’s Name: Cabletron Systems, Inc.
Manufacturer’s Address: 35 Industrial Way
PO Box 5005
Rochester, NH 03867
European Representative Name: Mr. J. Solari
European Representative Address: Cabletron Systems Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG13 2PZ, England
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC
EC Directive 73/23/EEC EN 55022
Equipment Type/Environment: Networking Equipment, for use in a
Commercial or Light Industrial Environment.
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this notice conforms to the above directives.
Legal Representative in Europe
Mr. Ronald Fotino
Mr. J. Solari
Principal Compliance Engineer
Managing Director - E.M.E.A.
Rochester, NH, USA
Newbury, Berkshire, England