Cabletron Systems 1200 User Manual
Size:
1.65 Mb
Download

SIMPLEREMOTEBRIDGINGNETWORK

OVERVIEW

This chapter provides an example of a simple network using remote bridge devices to access four basic rate lines in the CyberSWITCH. Bridges are formed between each of the LANs to which the remote bridge devices are connected, and the LAN to which the CyberSWITCH is connected.

The following section provides the initial installation steps that would be used with any type of network installation.

INITIALINSTALLATIONSTEPS

The initial steps in the CyberSWITCH installation process are basically the same no matter how complicated the network. These steps are:

completing the requirement worksheets

ordering ISDN service

powering on the system

accessing Release Notes

connecting an administration console

setting up Telnet access

upgrading system software

changing defaults to secure system

returning configuration to factory defaults

The chapters Accessing the CyberSWITCHand Upgrading System Software(in the User’s Guide)describe each of these steps in detail.

Worksheets for this network are included on the next few pages.

CONFIGURING THESIMPLEREMOTEBRIDGE

Because this is a simple bridged network, you only need to fill out the System Details andBridging and Routing Information worksheets. The worksheets for Example 1 are on the following pages.

EXAMPLE NETWORKS

SYSTEMDETAILS

System Name: SITE1 PAP Password:_______________ CHAP Secret:___________________

RESOURCES

Type

Slot

Switch type

Synchronization type

BRI

1

5ESS

 

Ethernet_1

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LINES

BRI Lines

 

Name

 

Slot

 

Port

 

Line type

Call screen

TEI

SPID

 

Directory number

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line1

 

1

1

 

PPP

 

 

 

Auto

 

 

 

 

 

 

Line2

 

1

2

 

PPP

 

 

 

Auto

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line3

 

1

3

 

PPP

 

 

 

Auto

 

 

 

 

 

 

Line4

 

1

4

 

PPP

 

 

 

Auto

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRI Lines

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Name

 

 

Slot

 

Port

Framing type

Line coding

Sig. method

 

Line build-out

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V.35 and RS232 Lines

Name

Slot

Port

Device/Network

Idle character

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10 CyberSWITCH