Bushnell 260650 User Manual
4X40 / 6X50
Model #s: 260440/260650/260441/260651 Lit. #:
PARTS AND CONTROLS GUIDE
ABOUT BUSHNELL® EQUINOX™ DIGITAL NIGHT VISION
Congratulations on the purchase of your Bushnell® Equinox™ Digital Night Vision. Comprised of high quality electronics and optics, the Bushnell Equinox is a
HOW DIGITAL NIGHT VISION WORKS
Bushnell Digital Night Vision products collect existing light through the objective lens. The image is then processed through a 1/3” near
1.Open the battery compartment (9) by unscrewing the tightening bolt
2.Install two CR123 lithium batteries, inserted with polarity in the direction shown on the internal wall of the battery compartment.
3.Replace the battery compartment cap and secure it by tightening the screw bolt, turning clockwise until tight.
NOTE: Do not mix old and new batteries together. Replace both batteries at the same time. Do not mix battery types.
Remove the protective objective lens cover (7) from the objective lens(6). Press the ON button(1) until the green LED indicator(L1) turns on. The LCD screen inside the eyepiece(8) will power on.
Point the Equinox night vision unit at the object you wish to observe. To focus, first rotate the diopter setting ring of the eyepiece (8) until the edges of the rectangular LCD screen appear as sharp as possible to your eye. Then rotate the objective lens focusing collar(6) until the observed image is sharp. To focus on another object at a different distance, you will only need to adjust the objective lens focusing collar(6), as the diopter setting is already optimized for your individual eyesight. You may need to readjust the diopter setting the next time you use the Equinox unit or if the eyepiece is moved accidently.
To turn the unit off, press and hold the ON button (1) for approximately 2 seconds until the green LED indicator(L1) turns off. Replace the protective objective lens cap cover(7) before storing or transporting the unit.
USING THE IR Illuminator
When using the unit under conditions of total darkness, turn on the IR illuminator (10) by pressing the IR button(2). When the IR illuminator is on, the red LED indicator(L2) will turn on.
NOTE: The IR light source is invisible to the unaided eye, but can be seen by other people equipped with night vision devices (be aware of this if using the unit for surveillance or law enforcement applications).
To turn the IR illuminator off, hold the IR button (2) for approximately
The IR illuminator is at the maximum brightness setting when it is first switched on. To decrease the brightness, hold the IR button (2) until the desired level of illumination is reached, then release the button. To increase the brightness of the IR illuminator if you turn it down too far, repeat the process by turning the IR on (to restart from the maximum setting) and again hold the IR button briefly (if necessary) to adjust the brightness to the desired setting.
ADJUSTING THE LCD DISPLAY BRIGHTNESS
To increase and decrease LCD screen brightness, press and hold the LCD brightness button (3). To reverse the direction of the brightness adjustment, release the LCD brightness button(3) and then press and hold the button until the desired level of brightness achieved to allow comfortable viewing experience.
NOTE: When the unit is turned on again, the LCD screen brightness setting will be at the same level as previously set.
SWITCHING THE LCD DISPLAY COLOR
To switch the LCD screen color from green to white or from white to green, quickly press the LCD backlight color mode button (4).
LOW BATTERY INDICATOR
The green LED (L1) starts flashing when the battery power is less than approximately 15% of full capacity. Replace both batteries as directed in "Battery Installation".
VIDEO OUT JACK
The device is equipped with an analog (composite) video out jack. Connect the video cable between the video output jack (11) and a compatible device (VCR, camcorder, video monitor, computer video interface, etc) to remotely observe or record the image produced by the Equinox digital night vision unit. A standard tripod mounting socket is provided.Refer to "Specifications" regarding NTSC/PAL video system compatibility for your Equinox model number.
EXTERNAL DC POWER IN JACK
To connect the device to a vehicle's DC outlet ("cigarette lighter socket"), plug the vehicle power adapter included with the device, into the 5V DC power input jack(12) and connect the other end to the vehicle power outlet
WARNING: The voltage produced by a vehicle's electrical system may vary from 12V to 24V depending on the model. The Equinox night vision units are designed for a DC input voltage of 5V, therefore do not plug the device into the vehicle outlet using an aftermarket 12V adapter. Use only the supplied power adapter, which is equipped with a
NOTE: To connect the device to 120V household AC outlet, you may use any commercially available AC adapter (NOT INCLUDED) which meets the requirements listed in the Specifications list in this manual.
WARNING: The batteries installed in the battery compartment of the device cannot be charged when the device is connected via external DC or AC power sources/adapters.
Unit does not turn on
1.Reinstall the batteries, making sure of the correct polarity (+/- terminals) orientation.
2.Replace both batteries.
3.Clean the battery compartment, especially the contact points.
Observed image is too bright
The ambient light level is too high (e.g. observation during bright sun conditions).
1.Turn off the unit or place the objective lens cover (7) over the lens. The unit will function normally in light conditions below 25,000 Lx (day light).
2.Adjust the LCD screen brightness (see "Adjusting the LCD Display Brightness" in this instruction manual).
Image is missing or not focused
(8) until the edges of the LCD display appear sharp (see "Focusing" in this instruction manual).
2.Check the condition of the objective lens (6) surface and eyepiece(8) and clean if necessary.
3.Replace the batteries.
4.In extreme low light conditions, activate the
Image disappears or its quality is reduced
Bright light sources (e. g. street lights at night time) may cause decreased visibility or reduced contrast.
1.Turn the monocular away from the light source; visibility will return momentarily.
2.Readjust the LCD display brightness setting.
Small black dots are visible on the screen
Small dots are normal, minor cosmetic blemishes resulting from the LCD manufacturing process and are not a defect or quality control error. These dots do not interfere with the reliability and performance of the monocular.
CARE AND MAINTENANCE
Your Bushnell Equinox Digital Night Vision device was designed to provide many years of reliable service. To ensure that you get the most enjoyment out of your Digital Night Vision device, always obey the following warnings and precautions.
•Keep the device away from any heating and air conditioning vents or other heating devices, direct sunlight, and moisture.
•Always store the unit in its carrying case in a dry well ventilated space in temperature above +15°C (60° F). Do not store near heating devices. Do not store in direct sunlight or high humidity conditions (higher than 70 %).
•Clean the optical lens with camera lens cleaning supplies.
•Clean the exterior of the device with a soft clean cloth.
•Remove the batteries if the device will not be used for longer than a few weeks.
WARNING AND PRECAUTIONS
•Avoid dropping or otherwise shocking the unit. Although designed for rugged outdoor use, this device incorporates sophisticated digital circuitry which could be damaged in extreme cases of misuse.
•Do not open the body of the device or otherwise attempt to service this device.
•Never pour alcohol or any other liquids directly onto the lens surfaces.
•Do not clean lenses and unit surfaces with paper based products, such as newspaper, textbook paper, etc. as it can damage the coating.
•Avoid removing the eyepiece as the LCD display could become damaged.
•Do not leave the device in direct sunlight or rain. The unit is water resistant, but is not designed for prolonged exposure to moisture and cannot be submerged in water.
•After the unit is operated in temperatures below zero, wait at least 3 hours at room temperature, to avoid condensation accumulating on the internal lens surfaces and the consequent fogging caused by extreme temperature differences.