Buffalo Technology AirStation Nfiniti WZR-G300N User Manual

Size:
699.51 Kb
Download

Quick Setup Guide - AirStation Draft-NWZR-G300N

Nfiniti Wireless Router & AP

Package Contents

WZR-G300NAirStation

Base Stand

AC Adapter and Power Cable

CAT5 LAN cable

Utility CD with Manual

Quick Setup Guide

Warranty Statement

http://www.buffalo-technology.com/

PY00-32004-DM20-01

 

 

1-01

Step 1: Connect Your Equipment

1. Make sure that all equipment is powered off, including the AirStation, PCs, and your cable or DSL modem.

2. Connect the Ethernet cable from your cable or DSL modem to the WAN port on your AirStation. The WAN port is the port closest to the power connector. This is the only port that will work for your internet connection.

3. Connect one or more PCs or workstations to any of the four LAN ports on the AirStation withRJ-45Ethernet cables.

4. Power on the cable or DSL modem. Give it at least a minute to boot up.

5. Connect the power connector to the power port on the AirStation and to a surge protector or other source of power. Give the AirStation 60 seconds to boot.

Step 2: Configure Your Router

Next, you need to configure your router. This is done from a web browser on a computer connected to the router. We recommend that you use a wired computer that is plugged into the

AirStation with an Ethernet cable for initial configuration.

1. Launch the web browser on the computer that you’re going to use to configure the AirStation. NOTE: The computer used to configure the AirStation should be set to obtain an IP addressautomatically using a DHCP server.

2. Your web browser should automatically attempt to load a web page. If the default web page loads then the AirStation has automatically configured your Internet connection settings.

Please skip to the next page if you have successfully connected to the Internet.

3. If the AirStation cannot automatically configure itself for your Internet Connection, then a window will open, prompting you to enter a User ID and Password.

Enter root as the User name and leave the password fieldblank.

NOTE: If your web browser doesn’t automatically connect you to the AirStation Configuration Utility, then type http://192.168.11.1 in its address field, and pressEnter.

4. The AirStation will provide different configuration options depending on what it has autodetected. Please manually enter your specific connection information. This information can be supplied by your Internet Service Provider; contact them for account specific information.

Step 3: Configure Wireless Settings

A. From a web bowser or a PC on the network, log into the AirStation Configuration Utility. Open a web browser, type http://192.168.11.1 into the addressfield and press Enter. Enter root as the User name

and leave the password field blank. This will take you to the Home page, where you can click on the System

Info tab.

B. TheSystem Info page gives you all the current information for your AirStation. When performing a survey with your wireless client device, pleaseconnect to the SSID provided on this System Info page.

Note: If you would rather use AOSS to automatically configure your wireless settingsfor you, turn to page 6.

Step 3: Configure Wireless Settings

C. The Wireless Settings(Advanced->Wireless->802.11n) page allows you to control important aspects of your Wireless Router/AP:

SSID - The SSID is the name of your wireless network.

This is what you see when performing a wireless scan or survey from a wireless client. You might want to change this to something easy to recognise, like “MYNETWRK”.

Channel Selection - You may find it necessary tochange the AirStation’s channel to avoid interference with other 2.4 Ghz sources (such as cordless phones,

neighboring Wi-Finetworks, baby monitors, etc.). By default, theAuto Channel mode will attempt to locate the clearest channel possible.

Press the Apply button when you are finished making changes. If you made changes to the SSID, then your wireless clients will be disconnected and will need to be reconnected using the new SSID.

There are additional settings that should be considered, such as encryption,

MAC address filtering, output power, etc. Please consult the User Manual on the

AirNavigator CD-ROMfor detailed information about other settings.

Alternative Step 3: Configure Wireless Settings with AOSS

AOSS (AirStationOne-TouchSecure System) is a simple system for configuring your wireless network securely. If your router and your client device are installed and both support AOSS,then making a secure wireless connection between them is simple.

A. Push the AOSS button on the top of your router and hold it in for a few seconds. The AOSS lightwill begin to flash amber.

B. You now have two minutes to push the AOSS button on your client device and finish the connection. If your client device is a PC card, CardBus, USB, or PCI adapter, the AOSS button willprobably be in its Client Manager Software. Check your client device’s AOSS setup information for instructions on where to push or click the AOSS button.

After you’ve pressed both buttons, it will take about 30 seconds for the connection to complete.

When it’s finished, the AOSS light will glow a solid amber, without blinking. You now have a secure network connection!

Notes: If your client devices do not support AOSS, or you don’t want to use it, turn topage 4.

Only one AOSS wireless client adapter can be configured with the AOSS router at a time. The buttons will need to be re-pressed to connect each additional AOSS wireless client adapter.

Additional non-AOSSwireless devices can be connected to your wireless network by connecting themmanually. The encryption information is available in the AirStation Web Configuration Utility in the

AOSS section. Please consult the User Manual on the AirStation CD-ROMfor more information.

After you push the first AOSS button, you have 2 minutes to push the second AOSS button. If you run out of time, just push the first AOSS button again.

Congratulations! Your AirStation is installed and the basic setup has been configured. For ad- vanced settings and more detailed information, consult the User Manual, located on your AirNavigator CD-ROM.

Buffalo Technology Technical Support

Buffalo Technology offers Technical Support between the hours of 9am-6pm(GMT) Monday to Thursday and9am-4:30pm(GMT) Friday for this product. Customers in Europe can obtain Technical Support using the following information:

Online Help

Available on the enclosed AirNavigator CD.

Web

www.buffalo-technology.com

E-mail

helpdesk@buffalo-technology.ie

Telephone

UK only: 08712 50 12 60

 

Elsewhere: +353 61 708 050

The constantly evolving state of wireless products and operating systems requires Buffalo Technology to occasionally release updated software to take advantage of new technologies and to comply with industry standards. For the most recent software, firmware, driver, and technical whitepaper releases

available, please visit the Buffalo Technology website: www.buffalo-technology.com

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of compliance with the R&TTE Directive 1999/5/EC:

EN 60950-1:2001

Safety of Information Technology Equipment

EN 300328 V1.6.1: 2004

Technical requirements for spread-spectrumradio equipment

EN 301489-1V1.4.1: 2002, EN301489-17V1.2.1: 2002 EMC requirements forspread-spectrumradio equipment.

EN 50371: 2002

Intended use

This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and office use in all

EU and EFTA member states.

EU Countries intended for use

This device is intended for indoor Home and office use in the following countries:

Austria, Belgium, Germany, Denmark, Spain, Greece, France, Finland, Italy, Ireland,

Luxembourg, The Netherlands, Portugal, Sweden, United Kingdom, Cyprus, Czech Republic, Estonia, Hungry, Latvia, Lithuania, Malta, Poland, Slovak Republic and Slovenia.

The device is also authorised for use in all EFTA member states Iceland, Liechtenstein, Norway and Switzerland.

EU countries not intended for use

None

Potential restrictive use

This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and office use in all

EU and EFTA member states, except in France, Belgium and Italy where restrictive use applies.

In Italy the end-usershould apply for a license at the national spectrum authorities in order toobtain an authorization to use the device for setting up outdoor radio links.

In Belgium there is a restriction in outdoor use. The frequency range in which outdoor operation in Belgium is permitted is 2460 – 2483.5 MHz.

This device may not be used for setting up outdoor radio links in France. For more information see http://www.anfr.fr/ and/orhttp://www.art-telecom.fr

MEMO

10