Before Starting Operation...............................................................................................................................................7
Procedure of Reading This Manual................................................................................................................................9
2-2 Configuration of Software..................................................................................................................................1-5
2-3 Notes on use.....................................................................................................................................................1-6
2-5 Basic Operation of Software..............................................................................................................................1-7
Chapter 2 Preparation of Embroidery Machine
1. Names of Machine Components.............................................................................................................................2-2
2-1 Transportation of Machine.................................................................................................................................2-3
2-2 Installation of Machine.......................................................................................................................................2-3
2-3 Installation of Operation Panel...........................................................................................................................2-4
2-4 Mounting of Guard Bar......................................................................................................................................2-4
2-5 Mounting of Cotton Stand..................................................................................................................................2-5
2-6 Lubrication to Needle Bar Case.........................................................................................................................2-6
2-7 Connection of Personal Computer to Machines (for connecting 4 sets)............................................................2-7
2-8 Connection of Power Supply.............................................................................................................................2-9
2-9 Installation of Software....................................................................................................................................2-11
3. Preparation for Embroidering................................................................................................................................2-12
3-2 Replacement of Bobbin...................................................................................................................................2-14
3-3 Replacing and Selecting Needle......................................................................................................................2-15
3-4 Preparation of Machine for Operation..............................................................................................................2-16
3-5 Attachment of Embroidery Hoop and Frame...................................................................................................2-19
3-6 Adjustment of Thread tension..........................................................................................................................2-23
Chapter 3 Embroidering Procedures
Functions of Operation Panel......................................................................................................................................3-2
Flowchart of Preparation for Embroidering...............................................................................................................3-4
Run the Software.....................................................................................................................................................3-5
Turn on the Machine Power.....................................................................................................................................3-5
Register the Machine Name....................................................................................................................................3-6
Retrieve the Embroidery Data.................................................................................................................................3-6
Description of Screen...................................................................................................................................................4-3
Creating a Directory......................................................................................................................................................4-4
Select from Menu.....................................................................................................................................................4-7
Select from Menu.....................................................................................................................................................4-8
Recreate an icon.........................................................................................................................................................4-10
Reading Data in Floppy Disk......................................................................................................................................4-16
Reading DOS Format Data....................................................................................................................................4-16
Converting the Non DOS format data....................................................................................................................4-18
Reading Data in Paper Tape.......................................................................................................................................4-22
Settings for Data Reading..........................................................................................................................................4-24
Writing Data in DST Format.......................................................................................................................................4-25
Description of Screen...................................................................................................................................................5-4
Trim and pause........................................................................................................................................................5-8
Needle Bar and Speed Range.................................................................................................................................5-9
Status Bar..............................................................................................................................................................5-14
Back to Previous Status.............................................................................................................................................5-15
Point Symmetry......................................................................................................................................................5-17
Insert or Delete Code.............................................................................................................................................5-21
Setting Group for Repetition..................................................................................................................................5-27
Selecting from Menu..............................................................................................................................................5-27
Save As.................................................................................................................................................................5-31
When the Power to the Machine is Off....................................................................................................................6-2
When the Power to the Machine is On....................................................................................................................6-2
Description of Screen..................................................................................................................................................6-5
Settings before Turning On the Machine....................................................................................................................6-6
Displaying the Tool Bar............................................................................................................................................6-6
Displaying the Status Bar.........................................................................................................................................6-7
Upgrading the Version of Interface Board................................................................................................................6-7
Communication Port................................................................................................................................................6-7
Settings after Turning Power On.................................................................................................................................6-9
Status Bar................................................................................................................................................................6-9
Zoom In Specified Range......................................................................................................................................6-10
Fit to Window.........................................................................................................................................................6-10
Hoop position fine adjustment...............................................................................................................................6-11
Needle Bar and Speed Range...............................................................................................................................6-13
Minimizing and Aligning Windows..........................................................................................................................6-21
Copying Data to Other Machines...........................................................................................................................6-23
Upgrading the Machine Program...........................................................................................................................6-24
BE-0901E-AC-PC• BE-1201B-AC-PC13
Contents
Setting the Machine....................................................................................................................................................6-25
Same Speed Range...............................................................................................................................................6-26
End of embroidery..................................................................................................................................................6-35
Activate escape with pause....................................................................................................................................6-38
Short stitch speed reduction...................................................................................................................................6-39
Area Trace.............................................................................................................................................................6-41
Show Setting..........................................................................................................................................................6-43
Save Setting...........................................................................................................................................................6-46
Moving the Home Position.........................................................................................................................................6-54
Entering in the Step-forward/Step-back Mode........................................................................................................6-55
Setting Step-forward/Back Distance or Timing.......................................................................................................6-56
Save As..................................................................................................................................................................6-61
Running Other Programs...........................................................................................................................................6-62
1-1 Power Source....................................................................................................................................................7-2
1-2 Preparation for Embroidering.............................................................................................................................7-2
2-1 Stopping the Machine with the stop switch unit.................................................................................................7-3
2-2 Emergency Stop of the Machine with the shut-off switch unit............................................................................7-3
3. Permission for Hoop Movement..............................................................................................................................7-4
4. Jog Switches.............................................................................................................................................................7-5
4-1 Hoop Movement to Start Position......................................................................................................................7-5
5. Area Check................................................................................................................................................................7-6
5-2 Automatic Hoop Movement in Area...................................................................................................................7-6
7. Measures against Thread Breakage.......................................................................................................................7-8
Description of Screen..................................................................................................................................................8-3
Display Example of Details......................................................................................................................................8-5
Display Example of Thread Breakage Information on Needle Bar...........................................................................8-6
Display Example of Thread breakage Information in Pattern...................................................................................8-7
Display Example of Output Information...................................................................................................................8-8
Display Example of Total Output Information.........................................................................................................8-10
Thread Breakage Information on Needle Bar........................................................................................................8-14
Thread Breakage Information in Pattern................................................................................................................8-14
Total Output Information........................................................................................................................................8-16
Recess Time Setting..............................................................................................................................................8-17
Save As CSV................................................................................................................................................................8-18
Printing Production Report........................................................................................................................................8-19
1-1 Cleaning and Lubrication of Rotary Hook..........................................................................................................9-2
1-2 Cleaning of Needle Plate...................................................................................................................................9-3
1. Adjusting Needle Bar Height..................................................................................................................................10-2
2. Adjustment of Timing Between Needle and Rotary Hook...................................................................................10-6
3. Adjustment of Presser Foot Height.......................................................................................................................10-7
4. Adjustment of Thread Trimmer..............................................................................................................................10-8
6. Adjusting the Belt Tension...................................................................................................................................10-10