Broan 683 User Manual

0 (0)

READ AND SAVE

THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1.Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2.Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3.Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

4.Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6.Ducted fans must always be vented to the outdoors.

7.If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.

8.Never place a switch where it can be reached from a tub or shower.

9.This unit must be grounded.

CAUTION !

1.For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

2.To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

3.Please read specification label on product for further information and requirements.

Installer: Leave this manual with the homeowner.

Homeowner: Use and Care information on page 4.

CEILING VENTILATOR / VENTILADOR DE CIELO RASO

MODEL / MODELO 683

TYPICAL INSTALLATIONS

POWER CABLE

MOUNTING TABS

CEILING

JOIST

HOUSING

CEILING MATERIAL GRILLE

Housing mounted directly to joist 2x6 (or larger) Discharge parallel to joists.

POWER CABLE

MOUNTING TABS

2 x 4 CEILING JOIST or TRUSS

 

HOUSING

CEILING

GRILLE

MATERIAL

 

ADDITIONAL*

FRAMING

2 x 4 CEILING JOIST or TRUSS

Housing mounted to 2x4 truss

Requires additional framing for mounting tabs. Discharge parallel to joists.

 

POWER CABLE

ADDITIONAL

 

 

FRAMING*

 

 

MOUNTING

 

 

TABS

 

 

 

 

HOUSING

 

"I"

CEILING

 

 

"I"

JOIST

GRILLE

 

JOIST

MATERIAL

 

 

 

 

 

Housing mounted to “I” joist

Requires additional framing for mounting tabs. Discharge parallel to joists.

 

4" ROUND

POWER CABLE

DUCT

 

MOUNTING TABS

 

HOUSING

 

 

CEILING

 

ADDITIONAL

CEILING

MATERIAL

GRILLE

FRAMING*

JOIST

Housing mounted to additional framing

Discharge 900 to joists.

 

4" ROUND

POWER CABLE

DUCT

 

MOUNTING TABS

HOUSING

2 x 4

 

 

ADDITIONAL

2 x 4

CEILING

 

FRAMING

 

CEILING

GRILLE

* CEILING

MATERIAL

 

JOIST or

 

 

 

 

JOIST or

TRUSS

 

 

 

 

TRUSS

Housing mounted to 2x4 truss

Requires additional framing for mounting tabs. Discharge 900 to joists.

 

4" ROUND

POWER CABLE

DUCT

MOUNTING TABS

 

HOUSING

 

 

"I"

 

 

ADDITIONAL

"I"

CEILING

GRILLE

FRAMING*

JOIST

JOIST

 

MATERIAL

 

 

 

Housing mounted to “I” joist

Requires additional framing for mounting tabs. Discharge 900 to joists.

* Additional framing must be a 2x6 (minimum height), at least 9-inches long.

LEAY CONSERVE ESTAS

INSTRUCCIONES

ADVERTENCIA

PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES PERSONALES, OBSERVE LO SIGUIENTE:

1.Utilice esta unidad solamente de acuerdo con las instrucciones del fabricante. Si tiene preguntas comuníquese con el fabricante a la dirección o al número telefónico que se indica en la garantía.

2.Antes de dar servicio o limpiar la unidad, interrumpa el suministro de energía en el panel de servicio y bloquee los dispositivos de desconexión para evitar la reinstalación accidental de la energía. Cuando no se puedan bloquear los dispositivos de desconexión, fije seguramente en el panel de servicio un medio de advertencia que sea visible, como por ejemplo una etiqueta.

3.Una persona o personas calificadas deben realizar el trabajo de instalación y el cableado eléctrico, de acuerdo con todos los códigos y normas aplicables, inclusive los códigos y normas de construcción para evitar incendios.

4.Se necesita suficiente aire para que se realice la combustión y la descarga de gases adecuadas a través de la chimenea del equipo para quemar combustible a fin de evitar las corrientes de inversión. Observe los lineamientos del fabricante del equipo de calefacción y las normas de seguridad, como por ejemplo las publicadas por la Asociación Nacional de Protección contra Incendios (National Fire Protection Association: NFPA), y la Sociedad Americana de Ingenieros en Calefacción, Refrigeración y Sistemas de Acondicionamiento de Aire (American Society for Heating, Refrigeration and Air Conditioning Engineers: ASHRAE), y los códigos locales.ditioning Engineers (ASHRAE), and the local code authorities.

5.Cuando corte o perfore la pared o el cielo raso, tenga cuidado de no dañar el cableado eléctrico ni otras conexiones de servicios que se encuentren ocultas.

6.Los ventiladores con conductos siempre deben tener salida hacia el exterior.

7.Si se va a instalar esta unidad sobre una tina o ducha, debe marcarse que es apropiada para esta aplicación y conectarse a un GFCI (interruptor accionado por pérdida de conexión a tierra) en un circuito de derivación protegido.

8.Nunca coloque el interruptor en un lugar en donde se pueda alcanzar desde la tina o ducha.

9.Esta unidad debe conectarse a tierra.

PRECAUCIÓN !

1.Esta unidad debe usarse solamente para ventilación general. No la utilice para la descarga de materiales ni vapores peligrosos o explosivos.

2.Para evitar causar daño a los cojinetes del motor y pistones impulsores ruidosos y/o no balanceados, mantenga los aerosoles para pirca, el polvo de construcción, etc. lejos del motor.

3.Por favor consulte la información y los requerimientos adicionales contenidos en la etiqueta de especificaciones que se encuentra en el producto.

A la persona que realiza la instalación: Deje este manual con el dueño de la casa.

Al dueño de la casa: Las instrucciones de operación y limpieza se encuentran en la página 4.

Broan 683 User Manual
BOTTOM EDGE OF JOIST
BORDE INFERIOR DE LA VIGUETA
1-1/4
1
5/8

INSTALACIONES TÍPICAS

CABLE DE ALIMENTACIÓN ALETAS DE

MONTAJE

VEGUETA

DEL

TECHO CUBIERTA

MATERIAL

REJILLA

DEL TECHO

 

CUBIERTA MONTADA

DIRECTAMENTE EN LA VIGUETA

2x6 (o más grande). Descarga paralela a las viguetas.

CABLE DE ALIMENTACIÓN

ESTRUCTURA

 

ALETAS DE ADICIONAL *

MONTAJE

 

VIGUETA O

 

VIGUETA O

VIGA DE

 

VIGA DE

2x4 DE

 

2x4 DE

CIELO

 

CIELO

RASO

CUBIERTA

RASO

MATERIAL

REJILLA

DE CIELO RASO

CUBIERTA MONTADA EN UNA VIGA DE 2x4

Se requiere una estructura adicional para las aletas de montaje. Descarga paralela a las viguetas.

CABLE DE ALIMENTACIÓN

ESTRUCTURA

 

ADICIONAL *

ALETAS DE

 

MONTAJE

 

 

 

CUBIERTA

 

VIGUETA MATERIAL

 

 

 

VIGUETA

"I" DE CIELO RASO

REJILLA

 

"I"

CUBIERTA MONTADA EN UNA VIGUETA “I”

Se requiere una estructura adicional para las aletas de montaje. Descarga paralela a las viguetas.

 

CONDUCTO

CABLE

REDONDO DE

DE ALIMENTACIÓN

4" (10.2 CM)

ALETAS DE MONTAJE

CUBIERTA

MATERIAL

 

ESTRUCTURA

VIGUETA

DEL TECHO

REJILLA

ADICIONAL*

DEL TECHO

CUBIERTA MONTADA

EN UNA ESTRUCTURA ADICIONAL

Descarga a 90º de las viguetas.

 

CONDUCTO

CABLE DE

REDONDO

 

 

DE 4" (10,2 CM

 

ALIMENTACIÓN

 

 

ALETAS DE MONTAJE

 

 

 

 

 

 

 

 

 

CUBIERTA

VIGUETA

 

ESTRUCTURA

VIGUETA

O VIGA DE

MATERIAL

ADICIONAL*

O VIGA DE

2x4 DE

DE CIELO RASO

REJILLA

2x4 DE

CIELO

 

 

CIELO

RASO

 

 

RASO

CUBIERTA MONTADA EN UNA VIGA DE 2x4

Se requiere una estructura adicional para las aletas de montaje. Descarga a 90º de las viguetas.

CABLE DE

CONDUCTO

 

REDONDO DE

 

ALIMENTACIÓN

4" (10,2 CM)

 

ALETAS DE MONTAJE

 

CUBIERTA

 

 

 

 

ESTRUCTURA

 

VIGUETA MATERIAL

ADICIONAL*

VIGUETA

"I" DE CIELO RASO

REJILLA

"I"

CUBIERTA MONTADA EN UNA VIGUETA “I”

Se requiere una estructura adicional para las aletas de montaje. Descarga a 90º de las viguetas.

* La estructura adicional debe ser un tramo de 2x6 (altura mínima), de al menos 9 pulgadas (23 cm) de largo.

TYPICAL INSTALLATIONS

4" ROUND

 

 

DUCT

 

POWER

 

 

CABLE

 

HOUSING

MOUNTING

 

TAB

 

 

SUSPENDED

GRILLE

 

CEILING MATERIAL

 

 

 

SUSPENDED CEILINGS

Housing hung with wires - 3-point mount.

INSTALL THE HOUSING

- please note -

the following installation illustrations show 2 x 6 joists. if you have a truss or “i”- joist installation, mount the ventilator to the additional framing in the same manner. (Additional framing must be a 2x6 (minimum height), at least 9-inches long.)

New Construction

1.Choose the location for your fan in the ceiling. For best possible performance, use the shortest possible duct run and

a minimum number of

HOLES

elbows.

OROFICIOS

2. Position mounting brackets

 

against joist so that bottom

TAB

edge of housing will be

ALETA

flush with finished ceiling.

 

Additional positioning

feature for 5/8”, 1”, & 1-1/4” thick ceiling

material:

Holes in corners of housing are labeled with various ceiling material thicknesses. Position housing so bottom edge of joist is visible through a matched set of holes. The housing is now in the proper position for that ceiling material thickness.

Additional positioning feature for 1/2” thick ceiling material:

Bend two tabs, on side of housing, 900 outward. Lift housing until tabs contact underside of joist.

Mark the keyhole slot on both mounting brackets.

3.Set housing aside and drive nails partially into joist at the top of both keyhole marks.

4. Hang housing from nails and pound nails tight. To ensure a noise-free mount, pound another nail through the top hole of each mounting tab.

2

INSTALACIONES TÍPICAS

CONDUCTO

 

REDONDO DE

 

4" (10.2 CM)

CABLE

 

 

DE ALIMENTACIÓN

ALETA DE

CUBIERTA MONTAJE

MATERIAL DEL

TECHO SUSPENDIDO REJILLA

TECHOS SUSPENDIDOS

Cubierta montada con cables. Montaje de tres puntos.

INSTALACIÓN DE LA CUBIERTA

- POR FAVOR NOTE -

LAS SIGUIENTES ILUSTRACIONES DE LA INSTALACIÓN MUESTRAN VIGUETAS DE 2 X 6. SI LA INSTALACIÓN ES EN UNA VIGA O EN UNA VIGUETA EN “I”, MONTE EL VENTILADOR EN LA ESTRUCTURA ADICIONAL DE LA MISMA MANERA. (La estructura adicional debe ser un tramo de 2x6 (altura mínima), de al menos 9 pulgadas (23 cm) de largo.)

Construcción nueva

1.Seleccione la ubicación del ventilador con lámpara en el cielo raso. Para obtener el mejor rendimiento posible, utilice un tramo de conductos lo más corto posible y un

número mínimo de codos.

2.Coloque las abrazaderas de montaje contra la vigueta, de manera que el borde inferior de la cubierta quede al ras del cielo raso terminado.

Característica adicional para la colocación en material de cielo raso de 5/8” (1.6 cm), 1”

(2.5 cm) y 1 ¼” (3.2 cm):

Los orificios que se encuentran en las esquinas de la cubierta

están marcados con varios espesores del material del cielo raso. Coloque la cubierta de manera que el borde inferior de la vigueta sea visible a través del conjunto de orificios que coinciden. Ahora la cubierta se encuentra en la posición adecuada para ese espesor del material del cielo raso.

Característica adicional para la colocación en material de cielo raso de ½” (1.3 cm):

Doble a 90º y hacia afuera las dos aletas que se encuentran a los costados de la cubierta. Levante la cubierta hasta que las aletas entren en contacto con la cara inferior de la vigueta.

Marque el orificio con forma de cerradura de ambas abrazaderas de montaje.

3.Coloque la cubierta a un lado e introduzca parcialmente los clavos en la vigueta, en la parte

superior de ambas marcas de los orificios en forma de cerradura.

4.Suspenda la cubierta con los

clavos e introduzca los clavos completamente. Para asegurar un montaje sin ruido, coloque otro clavo en el orificio superior de cada aleta de montaje.

Loading...
+ 2 hidden pages