Broan 1051L-C User Manual
Safety Precautions ...................................................................
Model and Serial No. Identification .......................................
Transporting Compactor .........................................................
Manually Raising and Lowering Ram ....................................
Troubleshooting Guide ....................................................
Component Replacement .............................................
Greasing Compactor Mechanism ............................................
Wiring Diagrams ......................................................................
Parts Lists ....................................................................
9 thru 12
ALWAYS UNPLUG COMPACTOR FROM WALL OUTLET BEFORE SERVICING.
The service information is intended for use by a service technician who is familiar with proper and safe procedures to be followed when repairing electrical appliances and who is equipped with proper tools and testing devices. Repairs attempted or made improperly can result in personal injury or property damage. Hazards may develop from improper assembly or adjustments. While making repairs, persons not having the proper background may subject themselves to the risk of injury or electrical shock which can be serious or even fatal.
IMPORTANT - NOTE TO THE CONSUMER
If you perform service on your own Broan products, you must assume responsibility for personal injury or property damage which may result.
The specification label with model and serial numbers is located on the inside of the cabinet. It is visible after opening the drawer.
DO NOT use plastic bags other than those which have been designed for use in this compactor. Unauthorized bags may become caught in the mechanism.
With the drawer extended to the second stop, release the container latch and swing open door. Slide bag into drawer from front to back. Fold bag over top rim of drawer on all sides.
Press bag into all corners of the drawer. Smooth and shape the bag carefully - this will prevent the bag from being torn by the ram during compaction.
When transporting compactor, the ram should be electrically or
manually extended down into the drawer, preferably against a
load of stacked newspapers or other suitable material. If this is
not done, damage to the trunnion nut may occur.
Never transport compactor on its back or front. Damage to the
gearbox may occur. If it cannot be transported upright, it is
Using buttons on side of drawer, button bag in place by using
preferable to place it on its side.
prepunched holes in side of bag. NOTE: If you have difficulty
MANUALRAISINGAND LOWERING OF RAM
installing bag, move drawer completely from unit by lifting
front of drawer slightly and pulling forward (place on rug or
Unplug compactor cord from wall socket. Remove back panel.
other surface to protect
floor). This will clear back
The ram may be raised or lowered manually by using a 15/16"
of container from housing
socket to turn the drive screw nut. Clockwise will lower ram,
for easier bag installation.
counterclockwise will raise it.
Swing door shut and latch
it. Bag is locked between
door flange and drawer.
When door is closed and
latched properly, door
guide “V” will be snug in
“V” groove in drawer
flange. Bag should be
captured in “V” guide.
Failure to align “V” prop-
erly or to latch drawer to
door will cause the com-
pactor to function im-
I. Will not run. Dead -
Not plugged in securely.
Insert plug securely into
no sound. (Turn key
to start, if unit hums,
Circuit breaker or fuse
Check for condition
go to section III.
causing circuit breaker
or fuse to open. Correct
condition, then reset
circuit breaker or replace
Drawer not closed.
Push drawer to close.
Defective key switch.
Test motor - replace if
II. Runs continuously,
will not shut off.
Trunnion nut stripped.
Key switch incorrectly
Defective upper limit
Compactor should be on separate 15 ampere circuit
See section on motor replacement for test procedure.
See note in section covering chain derailment.
Inspect trunnion nut for any evidence of damage. If nut displays signs of thread destruction, replace nut, clean drive screw and regrease.
III. Will not run - hums
Defective upper limit
when key held in
Test motor - replace if
See section on motor
replacement for test
Plastic bag caught in
Remove plastic bag.
See section on removing
bags from tunnion nut.
Do not use bags other
than the compactor trash
bag designed and sold
by Broan for use in this
IV. Starts and reverses
Defective upper limit
immediately. Will not
go down into drawer.
Didn’t hold key long
V. Thermal cutout on
Defective upper limit
motor trips. (Com-
pactor may appear to
start by itself several
minutes after last
switch on motor.
use.) Smells hot.
VI. Drawer does not
open smoothly after
Bent roller mounting
compactor is leveled.
Tight roller track on
Bend top rail on track to
Latch binding on side of
Bend to adjust.
Defective drawer track.
VII. Does not compact
Insufficient amount of
cans. Lacks pres-
trash in drawer.
Bottles and/or cans are arranged too uniformly.
Grease drive screw and
trunnion bearing using
wheel bearing grease.
Worn rear trunnion
Replace trunnion bear-
VIII. Bags pulled
Using bags designed for
Use Broan compactor
down into drawer.
Improper installation of
Install bag correctly.
It is not necessary to replace motor.
Roller tracks should be kept clean to keep glass particles from wearing out rollers.
Apply Locktite® to threads.
Ram does not travel to bottom of drawer. Extends to 6" from bottom of basket. As more trash is deposited and unit is operated, compaction will take place.
Bottles and cans should be placed randomly in center of drawer. Cans and bottles neatly arranged are capable of supporting a tremendous amount of pressure.
See section on greasing mechanism.
Bag should be captured in “V” groove on right front of drawer.
CABINET REPLACEMENT - POWER PACK REMOVAL
A box or similar stand approximately 11” high x 15” long x 7” wide is recommended for power pack removal. The box must be able to support 60 lbs. or more since you will be placing the full weight of the power pack on it.
1.Unplug compactor from socket.
2.Remove drawer assembly from cabinet.
3.Remove Air Scentry tray and control panel.
4.Remove key switch control bracket assembly. Remove back panel.
5.Place box in cabinet and lower ram manually by turning 15/ 16" nut on sprocket clockwise. Box should support weight of power pack.
6.Remove the four 5/16" nuts supporting the power pack in the cabinet.
7.Disconnect ground wire attached to cabinet.
8.Turn 15/16" nut counterclockwise causing power pack to lower down out of cabinet. Pull power pack out through front of rear of compactor.
If you are replacing the cabinet, remove remaining parts from old cabinet and install on new. See appropriate sections of service manual.
Reverse procedure to install power pack. Be sure the weld strip, grommets, and spacers are in place. The lock nuts should be torqued to 5 ft./lbs. (60 inch/lbs.). Do not overtorque.
Be careful not to pinch or nick any wires when installing power pack in cabinet.
On units with a bag storage compartment, removal of the storage compartment will make replacement of the control panel easier.
1.Remove drawer assembly.
2.Remove the four screws securing the air scentry tray and the bottom of control panel to the cabinet.
3.Pull bottom of control panel out slightly and then up.
When installing the control panel, make sure lip on inside of control panel snaps behind the bend in the control panel bracket.
(Models 1050L & 1051L only)
Remove two screws on rear of compactor and the two 5/16" hex head screws inside the storage compartment. Slide compartment 5 back and lift off.
1.Pull out drawer until it stops.
2.Lift drawer slightly, then pull out drawer to second stop.
3.Lift drawer up and out of compactor.
DOOR LINER - LATCH ASSEMBLY
Remove the door from the drawer by unlatching the door and removing the hinge pins. The door liner can be removed from the door by removing the toe space cover and all screws holding the door liner to the door. Slide the door liner to side of door and lift off.
DRAWER AND BASE ROLLERS
All four of the rollers are secured with a 1/2" hex nut and slotted for screwdriver. Roller nuts are installed using LocktiteR and torqued to 20 foot pounds. Rollers are pregreased and should require no lubricant.
1.Unscrew level legs from base. Remove tee nuts that legs screw into.
2.Remove screws securing bottom assembly to the cabinet.
3.Lower the bottom down into the cabinet, back end first, then bring it up and out through the notches in the bottom flange of the cabinet.
SWITCH LOCATIONS KEY SWITCH
1.Remove control panel.
2.Remove two hex head screws supporting control panel bracket with 5/16" socket.
3.Pull bracket out and remove switch.
CONTROL PANEL BRACKET
UPPER LIMIT SWITCH
the door. Another switch located against the interlock switch is to provide the
TO REPLACE INTERLOCK SWITCH
1.Remove air scentry panel assembly.
2.Disconnect leads one by one and attach to new switch.
1.Remove back panel, drawer assembly and air scentry panel.
2.Lower ram manually to approx.
3.Remove screws from nut retainer.
4.Raise ram assembly slightly by hand and remove nut.
NOTE: Count the number of revolutions to spin off nut. TRUNNION must be reinstalled to same position.
5. Reinstall trunnion nut and retainer.
CONTINUAL STRIPPING OF TRUNNION NUT: POSSIBLE CAUSES:
1.Incorrect assembly of trunnion assembly.
2.Transporting compactor incorrectly.
3.Burr on main drive screw; sharp edge on
4.Upper limit switch adjustment.
REMOVING PLASTIC BAGS FROM TRUNNION NUT
1.Remove drawer assembly.
2.Lower ram to gain access to switch.
3.Remove air scentry tray.
4.Remove hex head screw with 5/16" socket, pull switch down and disconnect wires.
3 to 1
2 to 1
6 to 1
3 to 4
6 to 4
5 to 7
Only the trash compactor bags specifically designed and sold by Broan for use in the compactor should be used. Regular plastic garbage bags used in place of the Broan bags may be drawn into the mechanism. Removal of those bags is not covered by the warranty.
To remove bag from trunnion nut:
1.Remove back of compactor.
2.If possible to slide drawer slightly, remove the door by sliding out the two hinge pins and then prying the door over the lip on the drawer.
3.Liberally spray drive screw and trunnion nut with
4.Use 15/16" socket, and extension, and a 16" ratchet (for leverage) and manually turn the drive screw clockwise. (See section on manually raising and lowering ram.) By turning the drive screw clockwise, you will help back the bag out of the trunnion nut.
5.After removing bag, clean drive screw and regrease it with wheel bearing grease.
1. Lower ram manually approximately halfway.
Remove 1/4" drive pin. Slide off washers.
The interlock switch is a
4. Lift ram, causing drive screw to slide out of the motor trun-
nion bearing. Support motor/gearbox assembly since it is
type. It is located on the right side behind the air scentry panel.
Its contacts are normally open. the contacts close when the door
now free to pivot. Unscrew drive screw from front trunnion
is closed. It is activated by the actuator located on the back of
1.Remove sprocket and drive pin.
2.Pull out trunnion bearing.
Grease trunnion bearing inside and out with wheel bearing grease prior to reinstalling.
1.Remove motor, gearbox, spocket, and screw guard.
2.Use 13/16" wrench to remove bolts securing links to motor trunnion.
When reinstalling, bolts torque to 45 foot pounds.
1.Line up one of the 3/8" holes in the sprocket with the 3/8" hole in bottom center of gearbox. Insert 3/8" steel pin or bolt through sprocket hole into front and rear gearbox holes.*
2.Loosen and remove 15/16" nut on the drive screw. When reinstalling torque to 65 foot pounds and apply Locktite® to threads.
*If the sprocket is too damaged to be able to use on of the holes to secure it, chip away the remaining sprocket, remove the drive pin and then insert a screwdriver through the hole to provide a means of keeping the drive screw from turning.
1.Turn sprocket until two holes in sprocket line up with socket head cap screws.
2.Remove socket head cap screws and tip gearbox/motor assembly to remove chain. NOTE: The screws thread into 2 nuts which rest in slots in the motor trunnion. Be careful not to lose the 2 nuts when the screws are removed.
When reinstalling socket head cap screws, be sure Locktite® is applied to the nuts.
Chain Derailment: Loose chains. Sometimes a chain will derail because trash which flew up above the ram during compacting fouled the chain. Newspaper or a paper bag should be placed on top of glass bottles before compacting to prevent this.
If continual derailment of the chain is a problem, inspect both sprockets for worn or missing teeth.
Inspect gearbox mounting and mounting plate. If the mounting screws are loose, gearbox movement may be the cause. If the gearbox mounting plate is bent where it meets the motor trunnion,eitherstraightenorreplace the gearbox.
Somechainloosenessisnormal and may increase as the compactor is used. Seldom does the chain “stretch” to the point where it is too loose.
1.Lower ram manually until there is approximately 11" to 12" between the ram and the bottom assembly.
2.Remove the four 3/8" nuts securing motor to gearbox, slide motor out and rest it on the front trunnion assembly.
3.Turn sprocket until two holes in sprocket line up with the two socket head cap screws that hold the gearbox to the motor trunnion.
4.Remove the two socket head cap screws with a 5/32" hex key. NOTE: The screws thread into 2 nuts which rest in slots in the motor trunnion. Be careful not to lose the 2 nuts when the screws are removed.
5.Tilt gearbox forward and remove chain. Lift gearbox out.
When installing gearbox, Locktite® should be applied to the socket head cap screw nuts.
5/32” HEX KEY
1.Unplug compactor from wall outlet.
2.Remove drawer assembly from compactor.
3.Remove back of compactor and lower mechanism manually by turning 5/8" nut on sprocket clockwise.
4.Line up one of the holes in the black sprocket with the hole in the gearbox. Insert a 3/8" bolt or pin to keep sprocket from turning and remove the 15/16" nut.
5.Slide off sprocket and washer.
6.Drive out the drive pin, slide off thin washer and pull out trunnion bearing.
7.Grease trunnion bearing everywhere, inside and out, with regular wheel bearing grease.
8.Reassemble unit in reverse procedure. When reinstalling 15/ 16" nut, be sure to apply a drop of Locktite® or equivalent to the threads of the 15/16" nut.
Apply grease to length of drive screw and a dab to the scissor
links at the pivot points.
Before motor is removed, it should be tested to be sure it is inoperative. Check the continuity of the motor.
Black to Orange
If open, replace motor
Red to Orange
If open, replace motor
Gray to Orange
If open, replace motor
Green to Motor Frame If open, inspect wire to be sure it is properly attached to motor frame
1.Lower ram manually until there is approximately 7" between the bottom assembly and the ram.
2.Disconnect molex connector from motor to wire harness.
3.Using a 3/8" nut driver or socket, remove the four nuts holding the motor to the gearbox. Remove air scentry tray and pull motor out through front of compactor.
4.Install motor in reverse procedure.
93030201 CENTRIFUGAL SWITCH (USED ON EMERSON MOTOR)
SCHEMATIC SHOWS UNIT AT END OF CYCLE - IN TOP POSITION DRAWER OPEN
BK (or BR)
L1 GN N COMPACTOR
CW START UP
R CCW START DOWN
BR 3 GY RUN
OFF - ON
START - RUN
Page 1 of 4
Control Panel Bracket (Models 1050L& 1051L)
Control Panel Bracket (Models 1055 & 1059)
Control Panel (Model 1050L)
Control Panel (Model 1051L)
Control Panel (Model 1055)
Control Panel (Model 1059)
Control Panel Insert (Model 1050L)
Control Panel Insert (Model 1051L)
Control Panel Insert (Model 1055)
Control Panel Insert (Model 1059)
Air Scentry Panel / Switch Assembly
Cabinet, (Includes Mounting Stud Strips 91007999) (Models 1050L & 1051L)
Bottom Assembly (Includes Rollers 93470012)
Latch Box Assembly
Cutting Board (order Model #1004)
Storage Compartment (Models 1050L & 1051L only)
Pad for Level Legs
Black Storage Compartment Door (Model 1050L)
White Storage Compartment Door (Model 1051L)
Rubber Grommets (Includes Spacers) Pkg. of Four
Nut, Hex Lock
Mounting Stud Strip Assembly
Page 2 of 4
Switch Assembly, Top Limit
Bolt - Special
Top Rail Assembly, Right
Top Rail Assembly, Left
Pin, Upper Rear
Spacer, Rail, Rear
Shaft, Lower 7.218 Long
Link Assembly, Peened
Ram Mounting Channel
Cap Screw, Hex
Spacer, Ram Front
Spacer, Ram Rear