BOSS 606C User Manual

Size:
486.83 Kb
Download

CONTENTS

 

Installation...................................................................................................................

3

DIN Front-Mount(Method A)........................................................................................

3

Installing the unit ...................................................................................................

3

Removing the unit..................................................................................................

4

DIN Rear-Mount(Method B).........................................................................................

5

Using the Detachable Front Panel ............................................................................

6

Wiring Connection......................................................................................................

7

Operation ....................................................................................................................

8

General Operation .................................................................................................

9

Radio Operation ..................................................................................................

10

CD Operation.......................................................................................................

10

Disc Notes ...........................................................................................................

11

Specification .............................................................................................................

12

Trouble shooting.......................................................................................................

13

2

INSTALLATION

Notes:

Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.

Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

If installation angle exceeds 30˚ from horizontal, the unit might not give its optimum performance.

30˚

Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either from “Front” (conventional DIN Frontmount) or “Rear” (DIN Rear-mountinstallation, utilizing threaded screw holes at the sides of the unit chassis).

For details, refer to the following illustrated installation methods.

TAKE OUT SCREWS BEFORE INSTALLATION

Before install the unit, please remove the two screws.

Take out screw before installation

DIN FRONT-MOUNT(Method A)

Installation Opening

This unit can be installed in any dashboard having an opening as show below:

53 mm

182 mm

Installing the unit

Be sure you test all connections first, and then follow these steps to install the unit.

1.Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-)terminal.

2.Disconnect the wire harness and the antenna.

3.Press the release button on the front panel and remove the control panel (see the steps of “remove the front panel”).

4.Lift the top of the outer trim ring then pull it out to remove it.

5.The two supplied keys release tabs inside the unit's sleeve so you can remove it. One key is for the right side and the other is for the left side. Insert the keys as far as they will go (with the notches facing up) into the appropriate slots at the middle left and right sides of the unit. Then slide the sleeve off the back of the unit.

3

INSTALLATION

Sleeve

L Key

Outer Trim Ring

Front Panel

R Key

6.Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place.

Dashboard

Tabs

Screwdriver

Sleeve

7.Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables.

8.Slide the unit into the sleeve until it locks into place.

9.To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle's mounting area. Then use the supplied hardware (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit.

Note: to install the short threading terminal of the mounting bolt to the back of the unit and the other long threading terminal to the dashboard.

Spring Washer Hex Nut

Metal Strap

Mounting Bolt

Plain Washer

Tapping Screw

10.Reconnect the cable to the vehicle battery's negative (-)terminal. Then replace the outer trim ring and install the unit's front panel. (see the steps of “install the front panel”).

Removing the unit

1.Make sure the ignition is turned off, then disconnect the cable from the vehicle battery's negative (-)terminal.

2.Remove the metal strap attached the back of the unit (if attached).

3.Press the release button to remove the front panel.

4.Lift the top of the outer trim ring then pull it out to remove it.

5.Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard.

4

INSTALLATION

DIN REAR-MOUNT(Method B)

If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle.

Side view showing

Screw Holes marked T, N

Factory Radio

 

Screw

Mounting

 

 

Bracket

 

 

 

 

Hook

Screw

Hook

Dashboard or

 

 

Console

 

 

To fasten the unit to the factory radio mounting brackets.

1.Use a screwdriver to loose the hook's screws on the front left and right sides of the unit and remove the hooks.

2.Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm) on

each side.

Note: the outer trim ring, sleeve and the metal strap are not used for method B installation.

5

USING THE DETACHABLE FRONT PANEL

REMOVE THE FRONT PANEL

1.Press the REL button on the front panel and pull off the front panel.

Release Button

Front Panel

2. Keep front panel into the case.

Protective Case

Front Panel

INSTALL THE FRONT PANEL

To install the front panel, insert the panel into the housing and make sure the panel is properly installed. Otherwise, abnormality occurs on the display or some keys will not function properly.

Precautions when Handling

1.Do not drop the front panel.

2.Do not put pressure on the display or control buttons when removing or installing the front panel.

3.Do not touch the contacts on the front panel or on the main unit body. It may result in poor electrical contact.

4.If any dirt or foreign substances adhered on the contacts, they can be removed with a clean and dry cloth.

5.Do not expose the front panel to high temperatures or direct sunlight in anywhere.

6.Keep away any volatile agents (e.g. benzene, thinner, or insecticides) from touching the surface of the front panel.

7.Do not attempt to disassemble the front panel.

6

WIRING CONNECTION

MAIN UNIT

ANTENNA CONNECTOR

 

FUSE

IGNITION

RED

 

SWITCH (ACC+)

 

Constant 12

FUSE

YELLOW

volts

 

GROUND (B–)

BLACK

 

POWER

BLUE

ANTENNA

 

FRONT Lch

WHITE

 

SPEAKER

WHITE/BLACK

 

REAR Lch

GREEN

 

SPEAKER

GREEN/BLACK

 

 

(BLACK)

AUX IN CABLE

Rch RED

 

Lch WHITE

 

(BROWN)

FRONT RCA CABLE

Rch RED

 

Lch WHITE

 

(GREY)

REAR RCA CABLE

Rch RED

 

Lch WHITE

GREY

FRONT Rch

 

GREY/BLACK

SPEAKER

 

VIOLET

REAR Rch

 

VIOLET/BLACK

SPEAKER

 

7

OPERATION

LOCATION OF KEYS

20

1

3

12 13

5

19

17

4

9

6

10

21

7

8

14

15

16

2

18

11

22

8

OPERATION

GENERAL OPERATION

ON/OFF

Switch on the unit by pressing any button (except REL button (6) and button (4)). When system is on, pressPOWER button (1) to turn off the unit.

FACEPLATE RELEASE

Press REL button (6) to detach the removable faceplate.

LOUDNESS

For the unit with two bands only:

Press and hold BND/LOU button (8) for several seconds to show the loudness state. And shortly press it again to turn on/off the subwoofer output. In CD mode or AUX mode, pressBND /LOU button (8) shortly to show the loudness state. And shortly press it again to turn on/off the bass output.

SET THE CLOCK

Press DSP button (9) shortly to switch display mode according to display priority set mode.

Press and hold DSP button (9) for several seconds until the clock is shown on the display and flashes, then pressVOL+/- button (20)(21) to change hours or the minutes.

SELECT AUDIO MODE

Press SEL/MENU (3) shortly to change audio mode through volume, bass, treble, balance, and fader modes. Press theVOL+/- button (20)(21) to adjust the selected mode. When the currently displayed function has not been adjusted for several seconds, the mode shall return to volume position and display will return to normal radio,

CD or AUX display.

VolumeBassTrebleBalanceFader

MENU SELECTION FUNCTION

Hold press SEL/MENU (3) for several seconds and you will enter the menu functions then press theSEL/MENU button to select the different modes.

Press the VOL+/- (20)(21) to select your setting.

BEEP ON/OFFProgram power on volume level CLOCK ON/OFF while power off

12hours/24hours CLOCK/FREQ priority

BEEP ON/OFF

-When the beep is on. It will beep with every button you press.

-When the beep is turned off. It will

not beep when you push a button.

Program power on volume level

In this mode, you can set the desired volume level when the unit turns on.

CLOCK ON/OFF while power off

In this mode, you can select if the clock is to be displayed while power off.

NO PRI/CLOCK/FREQ priority

- When select No Priority:

When the frequency appears on the unit, pressing DSP button (9) will display clock and it will not return to frequency display untilDSP button

(9) pressed again. When the clock appears on the unit, pressing DSP button (9) will display frequency information.

- When select Clock Priority:

The clock will appear on the unit all the time. Pressing DSP button (9) while in Clock Priority will temporarily display selected station frequency (in RADIO mode) or track number (in CD mode) and then returns to clock display.

-When select Frequency Priority:

The frequency will appear on the unit all the time. Pressing DSP button (9) while in Frequency Priority will

temporarily display clock and then returns to frequency display.

12hours/24hours

In this mode, you can set 24 hours mode or 12 hours mode. When the currently displayed function has not been adjusted for several seconds, it will exit menu set mode.

MUTE

In radio and AUX mode, press

9

OPERATION

(MUT) button (2) to mute the audio output. Press it again to release this mode and recover previous volume level.

EQUALIZATION

Press EQ button (10) shortly to turn on equalization function and to select desired audio mode. There are five kinds of mode as below:

FLATCLASSPOP MROCK M

SELECT MODE

Press MODE button (7) repeatedly to select among the following sources:

TUNER CDAUX

If no CD is present, CD mode will be skipped.

LIQUID CRYSTAL DISPLAY

The LCD (19) can show the current state of the unit.

RESET FUNCTION

RESET button (22) must be activated with either a ballpoint pen or thin metal object. TheRESET button is to be activated for the following reasons:

-Initial installation of the unit when all wiring is completed.

-All the function buttons do not operate.

-Error symbol on the display.

Note: If you press the RESET button (22), and the does not come back on, then use a cotton swab soaked in isopropyl alcohol to clean the socket on the front of the panel.

RADIO OPERATION

SWITCHING TO RADIO MODE

Press MODE button (7) to select radio mode, the radio mode appears in the display together with the memory band.

BAND

For the unit with two bands only, press BND/LOU button (8) shortly to change

bands as below:

FMAM

SELECT STATION

Rotate TUNING knob (11) clockwise orcounter-clockwiseto adjust the frequency upward or downward.

LOCAL/DISTANT

Press the LOC button (12) to select between local setting for reception of strong station and distant setting for reception of weak stations when tuning.

MONO/STEREO

In FM band, press MON button (13) shortly to select mono or stereo reception for radio stations. You can sometimes improve reception of distant stations by selecting mono operation.

CD OPERATION

SWITCHING TO CD MODE

If there is no CD inserted in the driver:

Gently insert the CD with the printed side up into the disc slot (5) until you feel some resistance. The CD is drawn into the driver automatically. CD playback begins.

If a CD is already inserted in the driver:

Keep pressing MODE button (7) shortly until the CD mode display appears.

EJECTING A DISC

Pressbutton (4) to stop CD play and eject CD from slot. Receiver switches to radio operation.

10