Bogen ASWG1DK User Manual
Models AS1, ASWG1, and ASWG1DK
Installation and Use Manual
Unmounted Cone Speaker with 1W Amplifier and
Grilles: CG8A, CG8AW,
SG8W, PG8A, PG8W
AS1 Mounted onto Steel Ceiling Grille (PG8W) with
Fixed, Center Volume Control Knob
TB8, RE84, MR8
AS1 Mounted onto Steel Ceiling Grille (PG8W) &
Detachable Volume Control Knob
Installation Instructions for ASWG1 and ASWG1DK
Note: Do not mount the speaker near noise generating equipment (fans, motors, etc.) and do not use where a normal conversation cannot be conducted.
TB8 and RE84 Installation
1.Place ceiling tile with the finished side facing up over a large trash can (to provide support and save cleanup time).
2.Cut hole in the center of the ceiling tile, using the raw speak-
er as a guide.
Bend (4) horseshoe tabs upward on tile bridge.
Position the tile bridge on the unfinished side of the ceiling tile
and bend (4) locator tabs into tile opening to prevent sliding.
click into place and secure
Punch out knockout in the RE84 and install Listed metallic
enclosure entry fitting to knockout to accommodate plenum
cable or plenum whip and feed cable or whip through the
Install RE84 to tile bridge by orienting horseshoe tab slots (4)
over horseshoe tabs (4) of bridge.
With pliers, twist horseshoe tabs (4) of tile bridge 1/2 turn,
securing enclosure to bridge.
Screw the Ceiling Speaker assembly to the RE84 using (4)
sandwiching the TB8 and ceiling tile in between. The screws
must go through the TB8 clearance holes as shown. (Screws
anchor into the RE84.)
© 2004 Bogen Communications, Inc. All rights reserved.
Specifications subject to change without notice.
TB8 Only Installation
1. Place ceiling tile with the finished side facing up over a large trash can (to provide support and save cleanup time).
2. Cut hole in the center of the ceiling tile, using the raw speaker as a guide.
3. Position the tile bridge on the unfinished side of the ceiling tile and bend (4) locator tabs into tile opening to prevent sliding.
4. Install Ceiling Speaker assembly using (4)
Electrical Connections and Adjustments
Power (24V DC) and audio are supplied to each speaker via four screw terminals. When two or more speakers are used in a single paging station, wire all audio and power supply connections in parallel.
Power supply connections are made at the screw terminals marked "+" and
A rotary control is provided to adjust the volume of the speaker. The ASWG1DK has a detachable knob to prevent tampering with the volume control.
The AS1, ASWG1, and ASWG1DK are warranted to be free from defects in material or workmanship for two (2) years from the date of sale to the original purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. The product will be returned to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN'S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. In no event shall Bogen be liable for special, incidental or consequential damages (including, but not limited to, loss of profits, loss of data or loss of use damages) arising out of the manufacture, sale or supplying of products, even if Bogen has been advised of the possibility of such damages or losses. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.
Products that are out of warranty will also be repaired by the Bogen Factory Service Department
50 Spring Street, Ramsey, NJ 07446, U.S.A.