Blue Rhino 62100 User Manual

Size:
931.27 Kb
Download

OWNER’S MANUAL

Outdoor LP Gas Patio Heater

Model No. 62100, 62900, 82300, 82300C, GWT501A & GWT801B

DANGER

CARBON MONOXIDE HAZARD

 

• This appliance can produce carbon

 

monoxide which has no odor.

 

• Using it in an enclosed space can kill you.

 

• Never use this appliance in an enclosed

 

space such as a camper, tent, car or home.

WARNING

FOR YOUR SAFETY:

For Outdoor Use Only

(outside any enclosure)

WARNING

FOR YOUR SAFETY:

1.Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.

2.Read the installation, operation, and maintenance instructions thoroughly before installing or servicing this equipment.

3.Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

California Proposition 65: Chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm are created by the combustion of propane.

Wash hands after handling this product.

Save these instructions for future reference.

If you are assembling this unit for someone else, give this manual to him or her to read and save for future reference.

Made from 70% Bagasse

(Environmentally Friendly Sugar

Cane Pulp By-product)

Table of Contents

 

Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 2

Exploded View & Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . 3

Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 4

Installing LP Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 6

Connect 20 lb. LP Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 6

Disconnect 20 lb. LP Gas Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 6

Secure 20 lb. LP Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 6

Connect (1) 14.1 oz or (1) 16.4 oz LP Gas Tank . . . . . . . . . . . . . . . . . . . . . .

. . . 6

Disconnect (1) 14.1 oz or (1) 16.4 oz LP Gas Tank . . . . . . . . . . . . . . . . . . . .

. . . 6

Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 7

Checking for Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 7

Before Turning LP Gas Supply “ON”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 8

Before Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 8

Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 8

When heater is “ON” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 8

Re-Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 8

Turning Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 8

Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 8

Cleaning Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 8

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 8

Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 9

Between Uses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 9

During Periods of Extended Inactivity or When Transporting . . . . . . . . . . . . .

. . . 9

Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 9

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 9

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 9

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 10

The use and installation of this product must conform to local codes. In absence of

local codes, use the National Fuel Gas Code, ANSI Z223.1/NFPA 54, CAN/CGA-B149.1,

Natural Gas and Propane Installation Code.

 

Manufactured in China for: Blue Rhino Global Sourcing, Inc Winston-Salem,NC 27105 USA

1.800.762.1142, www.bluerhino.com

© Blue Rhino Global Sourcing, Inc. All Rights Reserved

8200_s-OM-103EF

Outdoor Patio Heater Model No. 62100, 62900, 82300, 82300C, GWT501A & GWT801B

DANGERS and WARNINGS: FOR YOUR SAFETY

DANGER

If you smell gas -

1.Shut off gas to appliance.

2.Extinguish any open flame.

3.If odor continues, immediately call your gas supplier or your fire department.

WARNING

FOR YOUR SAFETY

1.Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

2.An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

DANGER: Failure to follow the dangers, warning and cautions in this manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property.

WARNING:

This heater is for outdoor use only, and shall not be used in a building, garage, or any other enclosed area.

Always maintain at least 36” clearance (top), and 24” clearance (side) from combustible materials.

This heater is NOT for commercial use.

This heater is for use with liquid propane (LP) gas only. The conversion to or attempted use of natural gas in this LP gas heater is dangerous and will void your warranty.

LP gas Characteristics:

a.LP gas is flammable and hazardous if handled improperly. Become aware of the characteristics before using any LP gas product.

b.LP gas is explosive under pressure, heavier than air, and settles and pools in low areas.

c.LP gas in its natural state has no odor. For your safety, an odorant is added that smells like rotten cabbage.

d.Contact with LP gas can cause freeze burns to skin.

LP gas tank needed to operate. Only tanks marked “propane” may be used.

The LP gas supply tank must be constructed and marked in accordance with the

Specifications for LP-gasCylinders of the U.S. Department of Transportation (DOT); or the Standard for Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods and Commission,CAN/CSA-B339,as applicable.

LP gas tank must be arranged for vapor withdrawal.

The LP gas tank must have a listed overfilling prevention device (OPD).

Only use 14.1-ounce,16.4-ounceor20-poundtank equipped with a tank connection device compatible with the connection for outdoor heating appliances.

The 20-poundLP gas tank must be equipped with a cylinder connection device compatible with the connection for outdoor cooking appliances.

The 20-poundLP gas tank must have a tank collar to protect the tank valve. Never use an LP gas tank with a damaged body, valve, collar, or footing.

Dented or rusted LP gas tanks may be hazardous and should be checked by your LP gas supplier prior to use.

The LP gas tank should not be dropped or handled roughly.

Tanks must be stored outdoors out of the reach of children and must not be stored in a building, garage, or any other enclosed area. Your tank must never be stored where temperatures can reach over 125°F.

Never keep a filled LP gas tank in a hot car or car trunk. Heat will cause the gas pressure to increase, which may open the relief valve and allow gas to escape.

Do not store a spare LP gas tank under or near this appliance. Never fill the tank beyond 80 percent full.

Never attempt to attach this heater to the self-containedLP gas system of a camper trailer, motor home, or house.

If the above two items not followed exactly, a fire causing death or serious injury may occur.

Place the dust cap on the cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on th cylinder valve that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane.

Never attempt to attach this heater to the self-containedLP gas system of a camper trailer, motor home, or house.

The use of alcohol, or prescription or non-prescriptiondrugs may impair the consumer’s ability to properly assemble or safely operate the appliance.

Your heater has been checked at all factory connections for leaks. Recheck all connections, as movement in shipping can loosen connections.

Check for leaks even if your unit was assembled for you by someone else.

Do not operate if gas leak is present. Gas leaks may cause a fire or explosion.

You must follow all leak-checkingprocedures before operating. To prevent fire or explosion hazard when testing for a leak:

a.Always perform leak test before lighting the heater and each time the tank is connected for use.

b.No smoking. Do not use or permit sources of ignition in the area while conducting a leak test.

c.Conduct the leak test outdoors in a well-ventilatedarea.

d.Do not use matches, lighters, or a flame to check for leaks.

e.Do not use heater until any and all leaks are corrected.

If you are unable to stop a leak, disconnect the LP gas supply. Call a gas appliance serviceman or your local LP gas supplier.

Do not store or use gasoline or other flammable liquids or vapors within 25 feet (7.62 m) of this appliance.

Do not use in an explosive atmosphere. Keep heater area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

Keep all combustible items and surfaces away from the heater at all times. DO NOT use this heater or any gas product under any overhead or near any unprotected combustible constructions.

Combustion of propane creates carbon monoxide, which, when used in enclosed areas, can kill you.

It is essential to keep the heater’s valve compartment, burners, and circulating air passages clean. Inspect heater before each use.

Installation and repair should be done by a qualified service person. Do not alter heater in any manner.

Do not use the heater unless it is COMPLETELY assembled and all parts are securely fastened and tightened.

This heater should be thoroughly inspected before each use. Clean and inspect the hose before each use of the appliance. If there is evidence of abrasion, wear, cuts, or leaks, the hose must be replaced prior to the appliance being put into operation.

Use only the regulator and hose assembly provided. The replacement regulator and hose assembly shall be that specified by the manufacturer.

Inspect heater before each use. If a damaged part is detected, do not operate until an original equipment replacement part has been properly installed.

Use only Blue Rhino Global Sourcing, Inc. factory authorized parts. The use of any part that is not factory authorized can be dangerous. This will also void your warranty. Contact 1.800.762.1142.

Dome and burner are extremely hot to the touch during operation. Never touch the dome or burner while the heater is operating. Wait for unit to cool down (approximately 45 minutes) after use.

During operation, do not touch burner assembly. The surface of heater’s emitter can reach temperatures approaching 1600ºF.

Do not install or use in or on boats or recreational vehicles. Do not use heater in winds that exceed 10 m.p.h..

Unit will operate at reduced efficiency below 40ºF (5ºC).

Do not leave a lit heater unattended, especially keep children and pets away from heater at all times.

Always use extreme caution when near heater. Alert both children and adults to the hazards of high temperatures, especially to avoid burns or clothing catching fire.

Do not attempt to move heater when in use. Allow the heater to cool before moving or storing.

Storage of heater indoors is permissible only if the tank is disconnected, removed from the heater and properly stored outdoors.

Do not attempt to disconnect the gas regulator from the tank or any gas fitting while the heater is in use.

Always place your heater on a hard, level surface. Use extreme caution on wooden decks.

Move gas hoses as far away as possible from hot surfaces. Keep all electrical cords away from a hot heater.

Do not use heater for indoor cooking or heating. TOXIC fumes can accumulate and cause asphyxiation.

Keep sprinklers and other water sources away from burner and controls. Do not hang clothing or other flammable materials either on or near heater. Always allow heater to cool before attempting service.

Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater.

Certain materials or items, when stored under heater, will be subjected to radiant heat and could be seriously damaged.

After a period of storage and/or non-use,check for leaks, burner obstructions and inspect for any abrasion, wear, cuts to the hose.

If at any time you are unable to light burner and smell gas, wait 5 minutes to allow gas to dissipate before attempting to light heater.

Failure to not wait 5 minutes to allow the gas to clear if the heater does not light, may result in an explosive flame-up.

Be careful when attempting to manually ignite this heater. Holding in the control knob for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition.

Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke.

If heater is not in use, the gas must be turned off at the supply tank, disconnected and stored correctly.

Do not use this appliance without reading “Operating Instructions” in this manual. Please use protective gloves when assembling this product.

Do not force parts together as this can result in personal injury or damage to the product.

Deaths, serious injury or damage to property may occur if the above is not followed exactly.

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

 

Parts List

 

 

Exploded View

1

Finial

56-01-001

 

 

 

 

 

 

 

 

2

Dome Cap

56-01-002

 

 

 

 

 

 

 

 

3

Dome

56-01-003

 

 

 

 

 

 

 

 

4

Top Wire Guard

56-01-004

 

 

 

 

 

 

 

 

5

Emitter Assembly

56-01-005

 

 

 

 

 

 

 

 

6

Burner

56-01-049

 

 

 

 

 

 

 

 

7

Bottom Wire Guard

56-01-006

 

 

 

 

 

 

 

 

8

Wind Cover

56-01-039

 

 

 

 

 

 

 

 

 

 

 

56-01-609(62100)

 

 

 

 

 

56-05-004(GWT501A)

 

9

Post

56-01-009(62900)

 

 

56-01-009(82300)

 

 

 

 

 

 

 

 

 

 

56-01-009(82300C)

 

 

 

 

56-01-009(GWT801B)

 

 

 

 

 

 

 

 

 

 

56-01-610(62100)

 

 

 

 

 

56-01-092(62900)

 

 

10

Shroud Cover

56-01-012(82300)

 

 

56-01-012(82300C)

 

 

 

 

 

 

 

 

56-05-005(GWT501A)

 

 

 

 

56-05-005(GWT801B)

 

 

 

 

 

 

 

11

ODS (Oxygen

 

 

 

Depletion Shutdown

56-01-007

 

 

 

 

Sensor)

 

 

 

 

 

 

 

 

 

12

Nozzle

56-01-017

 

 

 

 

 

 

 

 

13

Control Valve

56-01-018

 

 

 

 

 

 

 

 

14

Tilt Switch

56-01-019

 

 

 

 

 

 

 

 

15

Control Knob

56-01-020

 

 

 

 

 

 

 

 

16

Regulator

56-01-245

 

 

 

 

 

 

 

 

 

 

 

56-01-611(62100)

 

 

 

 

 

56-01-093(62900)

 

 

17

Housing

56-01-024(82300)

 

 

56-01-024(82300C)

 

 

 

 

 

 

 

 

56-05-003(GWT501A)

 

 

 

 

56-05-003(GWT801B)

 

 

 

 

 

 

 

 

 

 

56-01-612(62100)

 

 

 

 

 

56-01-094(62900)

 

 

18

Access Panel

56-01-030(82300)

 

 

56-01-030(82300C)

 

 

 

 

 

 

 

 

56-05-001(GWT501A)

 

 

 

 

56-01-030(GWT801B)

 

 

 

 

 

 

 

19

Plastic Ring

56-01-034

 

 

 

 

 

 

 

 

 

 

 

56-01-613(62100)

 

 

 

 

 

56-01-037(62900)

 

 

20

Base

56-01-037(82300)

 

 

56-01-037(82300C)

 

 

 

 

 

 

 

 

56-05-002(GWT501A)

 

 

 

 

56-05-002(GWT801B)

 

 

 

 

 

 

 

21

Weight Plate

56-01-041

 

 

 

 

 

 

 

 

22

Lock-upBracket Kit

56-01-044

 

 

(not shown)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

 

17

18

19

20

21

page no.

3

Hardware

 

 

Tools Required for Assembly (Not Included)

A

Screw

12-24x 3/16” Stainless Steel Phillips Truss Head

8 pcs

#2 Phillips Head Screwdriver

 

B

 

 

 

Nut

1/4-20Stainless Steel Hex Nut

3 pcs

 

 

 

 

 

Outdoor Patio Heater Model No. 62100, 62900, 82300, 82300C, GWT501A & GWT801B

Assembly Instructions

 

 

 

 

 

1

DO NOT RETURN PRODUCT TO STORE.

2

Attach Engine Assembly

 

 

 

For assistance call 1.800.762.1142 toll free. Please have your owner’s manual and serial number available for reference.

For Easiest Assembly:

To avoid losing any small components or hardware, assemble your product on a hard level surface that does not have cracks or openings.

Clear an area large enough to layout all components and hardware.

When applicable, tighten all hardware connections by hand first. Once the step is completed go back and fully tighten all hardware.

Follow all steps in order to properly assemble your product.

To complete assembly you will need:

(1) Leak Detection Solution (Instructions on how to make solution are included in step Operations Section)

(1) Precision Filled LP Gas Grill Tank with Acme Type 1 external threaded valve connection (4-5gallon size)

Note: You must follow all steps to properly assemble heater.

Typical assembly: approximately 20 minutes.

A

x 4

 

 

 

3 Attach Emitter Assembly

4 Attach Top Wire Guard

A

x 4

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

page no.

5

5 Attach Dome

B

x 3

7 Attach Access Panel

6 Attach Dome Cap and Finial

8

Secure Heater to Table

1. Attach the thumbscrew through the opening in the bracket in the base of the

heater.

2. Center heater over the umbrella pole opening in the center of the table, make

sure the thumbscrew is centered in the table opening.

3. Attach the bottom bracket from underneath, and secure the heater to the table.

Note: Hand tighten only. Do not use tools to tighten thumbscrew. Do not over tighten to prevent possible damage to table surface.

Outdoor Patio Heater Model No. 62100, 62900, 82300, 82300C, GWT501A & GWT801B

Installing LP Gas Tank

To operate you will need (1) precision-filledstandard grill

Figure 1

LP gas tank (20 lb.) with external valve threads or (1)

 

14.1 oz or (1) 16.4 oz LP gas tank.

 

Note: An empty standard grill LP gas tank weighs

 

approximately 18 lbs. A precision-filledstandard grill LP

 

gas tank should weigh no more than 38 lbs.

 

Only LP gas tanks marked “propane” may be used.

 

 

Figure 2

Connect 20 lb. LP Gas Tank

 

Note: Before connecting, be sure that there is no debris

 

caught in the head of the LP gas tank, head of the

 

regulator valve or in the head of the burner and burner

 

ports.

 

1. Slip end of flexible gas line with brass fitting through

 

center hole of Base and up to threaded portion of

 

regulator. (Figure 2)

 

2. Line up threads on fitting with those on regulator and

 

rotate clockwise until snug. HAND TIGHTEN ONLY.

 

DO NOT USE ANY HAND TOOLS TO MAKE THIS

 

CONNECTION. Be careful not to cross threads when

 

screwing in FITTING.

 

Note: hose can be routed through opening in base and

Figure 3

table.

 

3. Set heater on base, making sure that flexible gas line

 

is routed through small slot in base.

 

4. Connect gas line to tank by turning knob clockwise

 

until it stops. (Figure 3)

 

Note: Be careful not to kink flexible gas line.

 

CAUTION: When using the gas extension

 

hose always locate the hose out of pathways

 

where people may trip over it or in areas

 

where the hose may be subject to accidental

Figure 4

damage.

Disconnect 20 lb. LP Gas Tank

1.Turn LP gas tank valve to “CLOSED” and control knob is in the “OFF” position.

2.Disconnect gas line to tank by turning knob counterclockwise until it is loose. (Figure 4)

3.Disconnect gas line from regulator by turning flexible gas line counterclockwise until it is loose. (Figure 5)

Figure 5

4. Store the LP gas tank in a proper location.

Connect (1) 14.1 oz or (1) 16.4 oz

Figure 6

 

LP Gas Tank

 

Note: Some 1-lbcylinders may form frost when near empty.

1. Make sure the the control knob is “OFF”.

2. Line up threads on canister with those on regulator, insert and rotate canister clockwise until they fit snugly together. HAND TIGHTEN ONLY. Be careful not to cross threads when screwing in canister.

Disconnect (1) 14.1 oz or (1) 16.4 oz

LP Gas Tank

1.

Before disconnecting make sure the the control knob

Figure 7

 

is “OFF”.

2.

Rotate LP gas tank counterclockwise until it is loose.

 

3.

Store the LP gas tank in a proper location.

 

Operating Instructions

Inspect the visible portion of the hose before each use of the appliance. Inspect the entire hose assembly at least annually.

Checking for Leaks

Figure 8

Burner Connections

X

Make sure the regulator valve and hose connections are

 

securely fastened to the burner and the tank.

 

If your unit was assembled for you, visually check the

 

connection between the burner pipe and orifice. Make

 

sure the burner pipe fits over the orifice.

 

WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury, or damage to property.

If the burner pipe does not rest flush to the orifice, please

Figure 9

 

contact 1.800.762.1142 for assistance.

 

Tank/Gas Line Connection

X

1.

Make 2-3oz. of leak solution by mixing one part liquid

 

dishwashing soap with three parts water.

 

2.

Make sure control knobs are “OFF”.

 

3. Attach (1) 14.1 oz or (1) 16.4 oz or LP Gas LP gas

 

 

tank. Note: if using a 20 lb LP gas tank, turn control

 

 

valve to “OPEN”.

 

4.

Spoon leak check solution at all “x” and arrow

 

 

locations. (Figures 8-10)

 

5.

If any bubbles appear:

Figure 10

a.Disconnect gas tank per disconnecting instructions.

b.Reconnect gas tank per connecting instructions.

c. Repeat “Checking for Leaks”

X

If you continue to see bubbles after several

attempts, disconnect gas tank per disconnecting

instructions and contact 1.800.762.1142 for assistance.

If no bubbles appear after one minute turn tank “OFF”, wipe away solution and proceed.

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

page no.

7

Operating Instructions (continued)

Before Turning Gas Supply “ON”

WARNING: Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it inside a building, garage, or any other enclosed area.

WARNING: Make sure surrounding areas are free of combustible materials, gasoline, and other flammable vapors or liquids.

1.Ensure that there is no obstruction to air ventilation.

2.Be sure all gas connections are tight and there are no leaks.

3.Be sure the access panel is clear of debris.

4.Be sure any component removed during assembly or servicing is replaced and fastened prior to starting.

Before Lighting

1.Heater should be thoroughly inspected before each use, and by a qualified service person at least annually.

2.If relighting a hot heater, always wait at least 5 minutes for gas to dissipate.

Lighting

1.Turn control knob to “OFF” position. (Figure 11)

2.Connect LP gas tank.

3.If using an 20 lb LP gas tank, turn LP gas tank valve “OPEN”.

4.Push in control knob and rotate to “ON/HIGH” position. This will activate the built-inignitor and light the burner. If necessary, keep depressing and rotating knob until burner lights. (Figure 12)

5.Once burner is lit, hold control knob in for at least 30 seconds and release.

6.If burner does not stay lit, turn to “OFF” position and wait 5 minutes and repeat steps 2 and 3.

7.If ignitor does not light burner, use a lit match positioned against the bottom of emitter screen at burner location, and repeat steps 2 and 3.

(Figure 13)

8.Once burner is lit, rotate knob to desired heating level.

If you experience any ignition problem, turn off the heater and gas supply, and consult “Troubleshooting”.

Caution: Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke.

Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the control knob to the “LOW” position. Then, turn the knob to the level of heat desired.

When heater is “ON”:

1.Emitter screen will become bright red due to intense heat. The color is more visible at night.

2.Burner will display tongues of blue flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners.

3.If yellow flame is detected, turn off heater and gas supply and consult “Troubleshooting”.

Figure 11

OFF

ON

HIGH

LOW

Figure 12

OFF

ON

HIGH

LOW

Figure 13

Figure 14

4.Visually check burner flames at each use and make sure flame height matches illustration. (Figure 14)

Re-lighting

Note: For your safety, control knob cannot be turned on without first depressing control knob in off position and then rotating to on.

1.Turn gas control knob to off.

3.Repeat the “Lighting” steps 2 and 3.

2.Turn off gas at LP gas tank, or unscrew 14.1 oz or 16.4 oz LP gas tank.

3.Remove access panel.

4.Unscrew gas line from regulator.

5.Close access panel.

Note: After use, some discoloration of the emitter screen is normal.

Cleaning and Care

Notices

1.Abrasive cleaners will damage this product.

2.Never use oven cleaner to clean any part of heater.

3.Do not clean any heater part in a self cleaning oven. The extreme heat will damage the finish.

4.More frequent cleaning may be required as necessary. It is imperative that control compartment, burners and circulating air passageways of the heater be kept clean.

5.Spiders and insects can create a dangerous condition that may damage heater or make it unsafe. Keep burner area clean of all spiders, webs, or insects. Clean burner holes by using a heavy-dutypipe cleaner. Compressed air may help clear away smaller particles.

6.Inspect heater before each use.

7.Have heater inspected annually and repairs should be made by a qualified service person.

8.Check heater immediately if any of the following conditions exist:

a.The smell of gas in conjunction with extreme yellow tipping of burner flames.

b.Heater does not reach proper temperature.

Note: At temperatures less than 40ºF, heat output will be reduced.

c.Heater’s glow is excessively uneven

d.Burner makes popping noises during use.

Note: A slight pop is normal when burner is extinguished.

9.Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times.

10.Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water.

11.Do not paint engine, engine access panel or dome.

12.This heater should be thoroughly cleaned on a regular basis.

13.After a period of storage and/or non use, check for leaks, burner obstructions and inspect for any abrasion, wear, cuts to the hose.

Cleaning Surfaces

1.Wipe surfaces clean with mild dishwashing detergent or baking soda.

2.For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.

3.Rinse clean with water.

Note: While cleaning your unit, be sure to keep the area around the burner and pilot assembly dry at all times. Do not submerge the control valve assembly. If the gas control is submerged in water, do NOT use it. It must be replaced.

Maintenance

To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis:

1.Keep exterior surfaces clean.

2.Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs of possible blockage include:

Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven.

Heater makes popping noises.

Note: In a salt-airenvironment (such as near an ocean), corrosion occurs more quickly than normal. Frequently check for corroded areas and repair them promptly.

TIP: Usehigh-qualityautomobile wax to help maintain the appearance of your heater. Apply to exterior surfaces from the pole down. Do not apply to emitter screen or domes.

Turning Off

1.Rotate gas control knob to off position. Normally, burner will make a slight popping sound when extinguished.

Outdoor Patio Heater Model No. 62100, 62900, 82300, 82300C, GWT501A & GWT801B

Storage

Between uses:

1.Turn Control Knob OFF.

2.Disconnect LP source and move to a secure, well-ventilatedlocation outdoors.

3.Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris).

4.If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages.

Note: Wait until heater is cool before covering.

During periods of extended inactivity or when transporting:

1.Turn Control Knob OFF.

2.Disconnect LP source and move to a secure, well-ventilatedlocation outdoors.

3.Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris).

4.If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages.

5.Never leave LP canister exposed to direct sunlight or excessive heat.

Note: Wait until heater is cool before covering.

Product Registration

For faster warranty service, please register your product immediately at www.bluerhino.com or call 1.800.762.1142.

Limited Warranty

Blue Rhino Global Sourcing, Inc (“Vendor”) warrants to the original retail purchaser of this product, and to no other person, that if this product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such product shall be free from defects in material and workmanship. Vendor may require reasonable proof of your date of purchase. Therefore, you should retain your sales slip or invoice. This Limited Warranty shall be limited to the repair or replacement of parts, which prove defective under normal use and service and which Vendor shall determine in its reasonable discretion upon examination to be defective. Before returning any parts, you should contact Vendor’s Customer Service Department using the contact information listed below. If Vendor confirms, after examination, a defect covered by this Limited Warranty in any

returned part, and if Vendor approves the claim, Vendor will replace such defective part without charge. If you return defective parts, transportation charges must be prepaid by you. Vendor will return replacement parts to the original retail purchaser, freight or postage prepaid.

This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance or service by you or any third party, or failure to perform normal and routine maintenance on

the product as set out in this owner’s manual. In addition, the Limited Warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase.

This Limited Warranty is in lieu of all other express warranties. Vendor disclaims all warranties for products that are purchased from sellers other than authorized retailers or distributors, including the warranty of merchantability or the warranty of fitness for a particular purpose. VENDOR ALSO DISCLAIMS AND ANY ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. VENDOR SHALL NO LIABILITY TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Vendor further disclaims any implied or express warranty of, and assumes no responsibility for, defects in workmanship caused by third parties.

This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to everyone.

Vendor does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment, and no such representations are binding on Vendor.

Blue Rhino Global Sourcing, Inc Winston-Salem,North Carolina 27105 USA 1.800.762.1142

Specifications

Certifications:

ANS Z83.26a-2008• CSA2.37a-2008,Gas-FiredOutdoor Infrared Patio Heater

Rating:

Maximum 11,000 BTU/hr. input

Heat Range:

Up to 10 foot diameter

Fuel:

Liquid Propane Gas (LP)

Tank Size:

14.1 oz. (400 grams)

16.4 oz. (465 grams)

Inlet gas supply pressure:

Maximum – 150 PSI Minimum – 5 PSI

Manifold Pressure:

11.00 in. W.C.

Supply Pressure:

0.41 psig (11.00 in. W.C.)

Engine:

IPP E8

Safety Features:

Oxygen Depletion Sensor (ODS) shutdown system 100% Burner shut-off

Tilt Switch

Manufacturer:

Blue Rhino Global Sourcing, Inc

Made In:

China

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

page no.

9

Troubleshooting

Problem

Possible Cause

Prevention/Cure

 

 

 

Burner won’t stay lit

Connection between gas valve and burner assembly is loose

Tighten connection and perform leak check

 

 

Thermocouple is not operating correctly

Clean heater if still not working, obtain a new thermocouple

 

 

Gas pressure is low

Turn LP gas tank valve “CLOSED” and replace LP gas tank

 

 

 

Burner won’t light

Blockage in orifice

Clear blockage

 

 

Blockage in venturi tube

Clean venturi tube

 

 

 

 

 

Air in gas line

Open gas line and bleed it (pressing control knob in) for not more

Note: Heater operates at reduced efficiency below 40ºF (5ºC).

 

than 1 - 2 minutes or until you smell gas

 

 

Igniter fails

Use match to light pilot; obtain new igniter and replace

 

 

 

 

 

Control knob is not in “ON” position

Turn control knob to “ON”

 

Gas pressure is low

Turn LP gas tank valve “CLOSED” and replace LP gas tank

 

 

 

 

Outdoor temperature is less than 40ºF and tank is less than

Use a full tank

Burner flame is low

1/4 full

 

 

Supply hose is bent or kinked

Straighten hose

 

 

 

 

Control knob fully “ON”

Check burner and orifices for blockage

 

 

 

Emitter glows uneven

Gas pressure is low

Turn LP gas tank valve “CLOSED” and replace LP gas tank

 

Base is not on a level surface

Place heater on a level surface

Note: Bottom 1” of emitter normally does NOT glow.

Heater is level

Clean burner

Carbon build-up

Dirt or film on reflector and emitter

Clean reflector and emitter

Thick black smoke

Blockage in burner

Remove blockage and clean burner inside and outside

 

 

 

If problems can not be corrected by using these methods, please contact 1.800.762.1142 fo assistance.

Outdoor Patio Heater Model No. 62100, 62900, 82300, 82300C, GWT501A & GWT801B