Blaupunkt RP4-CH11 User Manual

0 (0)

Pacic Accessory Corporation

| Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

RP4-CH11

Radio Replacement & Steering Wheel Control Interface

for Chrysler/Dodge/Jeep Vehicles

Rev. 112811

Introduction & Features

Important Notes

Wiring Connection Chart

Illustration / Schematic

The RP4-CH11 interface allows the replacement of a factory radio in select Chrysler/Dodge/Jeep vehicles with MSCAN or

LSFT-CAN databus radios. Using this interface will retain factory features such as steering wheel controls (SWC) vehicle

entertainment system (VES) and the factory audio amplier whenever the original radio is removed. The RP4-CH11 also

provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination,

reverse trigger and parking brake.

1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the

interface into the vehicle (see next page for setting chart).

2. When the interface is rst plugged into the vehicle the LED will ash indicating the auto detect sequence. Once the CAN-BUS

speed is detected the LED will illuminate and should be on at all times when the interface is on. The LED will also ash whenever

a SWC button is pressed

3. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless

you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing

and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.

Red / White P.B. Output (-)

Purple / White VSS Output

Blue / White Amp Turn On Input

Red Acc. Output (1 amp)

Orange / White Illum. Output (+)

Green Reverse Output (+)

Interface Connector

Yellow Battery +12v

Black Ground

Blue Antenna On Input

White Front L + input

White / Black Front L - input

Grey Front R + input

Grey / Black Front R - input

Green Rear L + input

Green / Black Rear L - input

Purple Rear R + input

Purple / Black Rear R - input

Vehicle Connector

SWC Connector

Blu/Yel Kenwwod, Newer

JVC, OEM or

Blaupunkt

3.5mm Jack Alpine, JVC,

Clarion, Pioneer,

Sony, Valor, Boyo,

Dual, Visteon or

Advent

Accessory Output

+12volts 1amp max.

Pacific Accessory Corporation

Interface Connector

See above chart for

wire color descriptions.

Vehicle Connector

See above chart for

wire color description.

SWC Connection

See above chart for

different radio type

connections

Wiring SWC Connection

Page 1

Pacic Accessory Corporation

| Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

RP4-CH11

Radio Replacement & Steering Wheel Control Interface

for Chrysler/Dodge/Jeep Vehicles

Rev. 112811

Optional Steering Wheel Control Programming

IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming

unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by

pressing the program button on the side of the interface once and waiting for the timeout.

SET RADIO SELECT SWITCH

Installation Steps

1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio

setting before plugging the interface into the vehicle (see page 2 for setting chart).

2. Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your

particular vehicle.

3. Make all connections as described in the connection chart on page 1. Vehicles without a factory amplier: Connect the aftermarket radio’s

front and rear speaker wires to the vehicle connector. Vehicles with a factory amplier: The factory amplier only accepts two channels

of audio input (left and right). Connect the front outputs of the aftermarket radio to the rear inputs of the vehicle connector. This will allow

navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used. Fading is not

supported in this application. The factory amplier’s fading is controlled by data communication from the factory radio. Neither the aftermarket

radio or the RP interface have the ability to control the amplier’s fader.

4. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input)

5. If you wish to reassign functions to the SWC follow the programming instructions in the next section.

If you wish to re-assign the SWC functions, the interface must be programmed in the specic order shown in the chart on the next

page. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and

release the program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have

successfully skipped that function and are ready to proceed to the next one.

SET RADIO SELECT SWITCH

Alpine

Advent,

BOYO, Dual,

Visteon, Sony

Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor

1 7 8 4 2 3 6 7 5

SET RADIO SELECT SWITCH

Alpine

Advent,

BOYO, Dual,

Visteon, Sony

Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor

1 7 8 4 2 3 6 7 5

Default SWC Button Assignments

Alpine JVC Kenwood Clarion

alo

OEM Sony/Pionee

Blaupunkt

olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +

olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -

Source Source Source Source Source Source Source Source Source

Track + Track + Track + Track + Search + Track + Next Track + Track +

Track - Track - Track - Track - Search - Track - Previous Track - Track -

Preset + Preset + Preset Disc/Radio + Band Mute Band Preset + Disc +

oice Mute Mute Mute Mute Cursor - Answer Mute Mute

Phone Receive Receive

nswe

Send/End Cursor + Hang Up

nswe

Page 2

+ 2 hidden pages