Blaupunkt AUSTIN CD41 User Manual

Size:
1.72 Mb
Download

AUSTIN CD41

High-PowerFM/AM/CD Receiver with Detachable Face

Autoradio FM/AM à lecteur CD, de forte puissance et à face amovible Receptor FM/AM/Reproductor de CD de Alta Potencia y con Panel Extraíble Rádio FM/AM/CD de Alta Potência com Painel Removível

 

 

BND

200

WATTS

TS

 

 

CD41

 

CD

 

 

AUSTIN

 

 

 

 

DISP

 

PWR

 

 

 

SENS

MUTE

 

 

 

 

 

OPEN

T

 

 

XBASS

 

 

 

 

 

 

 

L

U

 

 

RPT

 

 

N

 

 

 

 

/

 

MIX

 

 

 

O

T

 

6

 

 

V

R

 

 

 

 

 

K

 

4

5

 

 

 

 

 

 

 

 

 

 

SC/PS

3

 

 

 

 

AUD

2

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

Robert Bosch Corporation Sales Group —

Blaupunkt Division 2800 South 25th Avenue, Broadview, Illinois 60155 www. blaupunkt. com

ENGLISH

FRANÇAIS

PORTUGUÊS ESPAÑOL

FCC WARNING

Precautions

Handling the Front Panel

This equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection aga hinst harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Features

Detachable Flip Down Front Panel

Built-inPower Amplifier (max. output : 50W× 4ch)

4-chF & R Preamp Output

2-chSubwoofer Preamp Output

FM/AM PLL Synthesizer Tuner

30 Station Preset Memory

Travel Store / Scan Tuning

X-BassSystem

Station Name, Disc Name Store / Station Call

Auxiliary-input

Optional IR Remote Control

CD Changer Control

(IDCA09, CDCA08 & CDCA071*)

*CDCA071 requires adaptor # 7607 898 093 available separately.

Avoid installing the unit where it would be subject to high temperatures, such as in direct sunlight or a hot air stream from the heater, or where it would be subject to dust, dirt, or excessive vibration.

Do not turn on the unit if the temperature inside the car is very high. Always cool down the unit before usage. Parking your car in direct sunlight will result in a temperature rise.

If the unit does not turn on, check the connections first. Then check whether the fuse at the back of the unit is blown.

Carefully read this manual before using the unit. If you encounter any problems that are not covered in this manual, please consult the dealer where you purchased the unit or the dealer nearest to you.

This unit has been designed specifically for playback of compact discs bearing the mark. Other discs cannot be played.

Do not use non-conventionaldiscs such asheart-shaped,octagonal discs, etc. The player could be dameged.

Handling Compact Discs

Be careful when removing a compact disc after the playback is completed because the disc may be extremely hot.

Do not use non-conventionaldiscs such asheart-shaped,octagonal discs, etc. The player could be damaged.

Do not expose compact discs to direct sunlight or any heat source.

Check all compact discs before playing, and discard cracked, scratched or warped discs.

Wipe dirty or damp discs outward from the centre with a soft cloth.

Do not use any solvents such as commercially available cleaners, antistatic spray, or thinner to clean the compact discs.

Attaching the Front Panel

Place the right hand side of the front panel so that the parts A of the front panel are engaged with the parts B of the unit as shown below. Then push the left hand side of the front panel until it is securely locked.

Front Panel Open / Close

Panel open

Panel close

Press the OPEN .

Raise the front panel with your

 

finger until it locks in place.

Security / Retailer Display

Bolt the front panel with the locking screw (See page 10) in the inner cover as shown below, to protect the front panel from robbery and from getting lost.

Locking screw

ENGLISH

FRANÇAIS

PORTUGUÊS ESPAÑOL

E-1

Identification of Controls

ENGLISH

FRANÇAIS

Notes

Be sure to use this unit with the front panel closed.

The unit is automatically switched off when the front panel is left open for about 10 minutes.

Do not handle the unit roughly when opening/closing the front panel.

Do not put any object or use it like a tray when the front panel is open in a lying position.

Do not press OPEN button when closing the front panel.

Do not put much force to the operation buttons or the display window as it may cause damage or deform the unit.

Connectors on the unit and front panel are vital parts transmitting the signal. Do not touch, push and scratch them.

Be careful not to pinch your fingers or hands when opening and closing the front panel.

Do not press hard on the front panel when affixing it to the unit. No more than light to moderate pressure should be needed.

Make sure there is no dust or dirt on the electrical terminals on the back of the front panel as this could cause intermittent operation or other malfunctions.

Clean with alcohol & swabs.

Detaching the Front Panel

1. Press theOPEN firmly to open the flip down front panel.

2. Pull the front panel toward your direction to remove it.

3. Close the inner cover.

Do not leave inner cover in the down position unless the front panel is in place.

ESPAÑOL

Ejecting the CD

 

Press the recessed button located to the left behind the Front

PORTUGUÊS

Panel.

 

 

EJECT button

1

2

3

4

15 5 6

OPEN

PWR

 

 

AUSTIN CD41

 

200 WATTS

 

 

 

 

 

 

 

 

TS

BND

 

 

L

 

 

 

 

 

 

 

V

O

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

 

 

 

U

 

 

 

 

 

 

 

CD

 

 

 

N

 

 

 

 

 

 

 

 

 

 

 

/

 

 

 

 

 

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

K

 

 

 

 

 

 

 

DISP

 

 

 

 

 

 

 

 

 

 

NS

 

 

 

 

AUD

SC/PS

 

 

MIX

RPT

XBASS

SE

 

 

 

 

 

 

MUTE

 

 

 

 

 

1

2

3

4

5

6

 

 

 

 

 

 

 

14

13 12

11

10

9

8

7

1OPEN button

Open the flip down front panel.

2PWR button

Turns the power of the unit on or off.

3TUN/TRK button

Used to tune in to the desired station.

4LCD Display window

5CD button

Select the operating source (CD, CD changer or AUX).

6BND/TS button

Selects the AM/FM Band & Travel store.

7DISP button

Mode selector. Clock adjustment. Display priority setting.

8MUTE/SENS button

Muting the sound. Switches the seek sensitivity between local and distance.

9XBASS button

Boosting the bass sound.

10PRESET MEMORY button During radio reception :

1 - 6

;

For Preset memory

During CD mode :

4/MIX

;

For Mix play (Mix & Mix all during CDC)

5/RPT

;

For Repeat play

6/

;

For Pause

E-2

General Operations

11DISC SELECT button

Select the desired CD in CDC (CD changer) mode.

12SC/PS button

Scan tuning. Preset scan tuning. Scan play in CD/CDC mode.

13AUD button

Audio control selector; Bass, Treble, Loudness, Balance & Fader.

14Dial

Adjusts the volume level/bass/treble/balance/fader.

Storing the station names. Select alfa-numericcharacters.

15Infrared Sensor (behind acrylic facia)

Permits wireless remote control of AM/FM/CD and CD changer with optional credit card style remote. See Dealer for Details.

Turning the power On/Off

Press the PWR to turn on or off the unit.

Tip

When you turn on the unit, “HELLO” will be displayed then “WELCOME” will momentarily be displayed before actual power on.

When you turn off the unit, “SEE YOU” will be displayed then “GOOD-BYE”will momentarily be displayed before actual power off.

You can edit these messages. (See “Turn on/off message edit”)

Volume Level Control and Memory

Rotate the dial to adjust the volume.

It is also possible to set the maximum volume for when the power is switched on by following the procedure explained below.

1. Turn the dial until it is set at the required volume.

Volume down

Volume up

2. Press thePWR for two or more seconds. The power will be switched off and the current volume level recorded.

Muting the sound

Press MUTE / SENS.

“ MUTE ” appears on the display window.

To restore the previous volume level, press MUTE / SENS again.

Setting the Clock

The clock uses a 12-hourdisplay system. (factory set)

ENGLISH

3.

Repeatedly press the

DISP

to display “ CLOCK 12 ”.

1.

Turn the ignition key to the ON position.

 

2.

Press the PWR to turn on the unit.

 

4.

Rotate the dial within 5 seconds to select the 12 or 24-

 

 

hour time mode. Each time you rotate the dial, the mode

 

 

changes or toggles as follows :

 

 

CLOCK 24

 

 

 

 

CLOCK 12

 

 

AIS

 

 

 

Ç

 

 

 

 

5.

Repeatedly press the

DISP

to display “ CLK ADJ ”.

FRAN

 

 

A. Press the MUTE / SENS

within 5 seconds to flash the hour digit.

 

B. Rotate the dial to set the hour digit.

C. Press the

MUTE / SENS to flash the minute digit.

 

D. Rotate the dial to set the minute digit.

ÑOL

6. Press the

DISP

momentarily to complete the Clock set-

ESPA

ting mode.

 

 

Note

 

 

 

 

 

If you make no button input or dial operation in 20 seconds,

 

the Clock setting mode will turn off automatically.

 

Ignition-offClock Recall

 

ÊS

The display will illuminate showing the time and then auto-

PORTUGU

matically shut off after 5 seconds.

Press the DISP

while the ignition switch is in the “ OFF ” posi-

 

tion.

 

 

 

 

 

 

 

E-3

Mode Selector

ENGLISH

Each time the DISP

is pressed, the display window will change

 

STN CALL

LEVEL 1 Temporary

METER 1

 

over as shown below;

 

 

 

Priority

 

 

 

 

 

(NO NAME)

 

 

 

CLOCK 12

CLK ADJ

MESSAGE

 

Display priority setting

 

ÇAIS

Display Priority can be set for the following items;

Radio mode

 

 

Frequency and Station Name, plus during

FRAN

CDC (CD changer) mode

 

 

 

 

Disc No, Track No, Track time and Disc name.

Example

To set Station Name to the Display Priority.

 

1.

Press the DISP

three times, and the temporary display

OL

2.

appears in the display window.

Hold the DISP

pressed for more than 2 seconds.

 

Ñ

 

“ NO NAME” or a previously assigned station name blinks

 

once to indicate that Station Name is selected for the Dis-

ESPA

 

 

play Priority.

 

 

 

 

 

 

After 5 seconds, the display mode will automatically re-

 

 

turn to the Display Priority showing either “NO NAME” or

 

 

the station name.

 

 

Tip

 

 

 

 

 

 

Frequency Display is initially set to the Display Priority,

 

 

S

 

and Station Name (“NO NAME”) is set to the “Tempo-

 

rary” indicator.

 

PORTUGUÊ

 

 

 

 

 

 

 

 

 

Adjusting the Sound Characteristics

1. Press the

AUD

to select the desired adjustment mode

as follows;

 

 

 

BASS 0

TREBLE 0

LOUD OFF (LOUDNESS)

R0 F0 (FADER)

L0 R0 (BALANCE)

2. Rotate the dial to adjust the selected item.

Adjust within 3 seconds after selecting the item. After 3 seconds, the dial reverts to volume control. Use the following tables as a guide for adjusting the settings in each mode.

Adjustment Range

BASS

BASS -5

BASS +5

TREBLE

TREBLE -5

TREBLE +5

 

 

 

LOUDNESS

LOUD OFF

LOUD ON

 

 

 

BALANCE

L9 R0(Full left)

L0 R9(Full right)

 

 

 

FADER

R9 F0(Full rear)

R0 F9(Full front)

 

 

 

Tip

Settings for BASS, TREBLE, LOUDNESS and XBASS can be made to each of the following modes independently:

FM, AM, CD Changer and AUX.

Switching the Source (Selecting auxiliary input)

You can connect the auxiliary equipment (Portable cassette player, MP3 player, etc.) to this radio via optional AUX-INcable. (See page 11)

Each time the CD is pressed, the operation source will change over as shown below;

 

 

CD

CD changer or AUX

Press the

BND / TS

to return to tuner mode.

Note

 

 

 

If the

CD

button is pressed when no CD has been loaded

into the unit, The CD mode will skip to the CD changer mode or AUX mode.

Also, if the CD changer is not connected, the system will move across to the AUX mode regardless of whether auxiliary equipment is connected or not (“MP3/AUX” will be displayed.)

It is not possible to switch to the AUX mode when the CD changer is connected.

Remote Control (Optional)

You can operate your receivers basic AM, FM, CD & CDC features via an optional IR Remote Control. Optional Credit Card type remotes are available. See dealer to order RC823 Credit Card remote.

E-4

BND / TS
BND / TS
MUTE / SENS
TUN/TRK

Radio Reception

Seek Tuning

1. Press theBND / TS to select the desired AM or FM band.

FM I FMII FT AM (A) AT (FT & AT are Travel Store bands.)

2. Press theto tune in stations. Tuning automatically stops at a broadcasting frequency.

SEEK ” indicator will appear on the display window. When tuned in to FM stereo broadcasting stations, the

” stereo signal indicator will appear on the display window.

Manual Tuning

1.

Press the

BND / TS

to select the desired AM or FM band.

2.

Press the

TUN/ TRK

or

TUN/TRK

for more than 0.5 sec-

 

ond to activate the manual tuning mode. Press again to

 

tune in to stations.

 

 

 

 

“ MANUAL ” indicator will appear on the display window.

 

After 4 seconds of completing Manual Tuning, the tuning

 

control will revert to the Seek Tuning mode.

Scan Tuning

 

 

 

 

1.

Press the

BND / TS

to select the desired AM or FM band.

2.

Hold the

SC/PS

pressed for less than 2 seconds.

 

The unit will scan the selected band for stations.

 

“ SCAN ” indicator will appear on the display window. The

 

unit will stop at each station for 8 seconds, before con-

 

tinuing to the next station.

 

 

Press the

SC/PS

again to stop Scan Tuning and remain

this on the selected frequency.

Tip

While tuning, the pie-shapedsignal-strengthmeter

on the display is lit differently depending on the strength of the signal. While scanning bands, the pie-shapedsig-nal-strengthmeter spins. While playing CD’s, this display spins also.

Preset Scan Tuning

1.

Press the

BND / TS to select the desired AM or FM band.

2.

Hold the

SC/PS

pressed for more than 2 seconds.

 

“ SCAN ” indicator will appear on the display window.

 

The unit will scan preset memory for the 12 stations from

 

the AM/AT band or the 18 stations from the FM I/FMII/

 

FT bands. The unit will stop at each preset station for 8

 

seconds, before continuing to the next preset station.

 

Press the

SC/PS

again to stop Preset Scan Tuning and

remain this on the selected frequency.

Memorizing Stations Automatically (Travel Store)

1. Press theto select the desired AM or FM band.

2. Hold thepressed for longer than 2 seconds. Up to 6 stations with strong signals will be automatically stored in preset memory for the selected band.

If the radio is in FM I or FMII, it switches to FT. If the radio is in AM, it switches to AT.

Note

This function is available for FT and AT.

Memorizing Only the Desired Stations

You can store up to 6 stations on each band (18 for FM I, FMII and FT, 12 for AM and AT) in the order of your choice.

1.

Press the

BND / TS to select the desired band.

2.

Press the

TUN/TRK

to tune in stations.

3.

Press and hold the desired preset memory button 1 -

 

6 for about 2 seconds until the frequency indicator

flashes twice.

The number of the pressed preset memory button appears on the display window.

Note

If when you store another station on the same preset number button, the previously stored station is replaced with new one.

Receiving the Memorized Stations

1.

Press the

BND / TS to select the desired AM or FM band.

2.

Press the

1 6 momentarily.

Local/Distant (LO/DX) Selection

This feature is used to select the signal strength at which the radio will stop during Seek Tuning.

Press the for more than 2 seconds to select the Local setting and only strong (local) stations will be received. The “ lo ” indicator appears on the display window.

Pressing for more than 2 seconds again will select the Distant setting and the radio will stop at a wider range of signals, including weaker more distant stations. The “ lo ” indicator will go out on the display window. DX is the suggested default setting.

ENGLISH

FRANÇAIS

PORTUGUÊS ESPAÑOL

E-5

TUN/ TRK
TUN/TRK

ENGLISH

FRANÇAIS

PORTUGUÊS ESPAÑOL

Storing the station names

You can assign a name to each radio station and store it in memory. As many as 30 station names can be stored composed with 8 characters each.

Storing the station names

1. Tune in a station whose name you want to store.

2. Press theDISP for more than 2 seconds.

The “ NAME EDT ” will light then the “ _ _ _ _ _ _ _ _ ” on the display window. The first “ _ ” flashes.

3. Enter the characters.

A.Rotate the dial in a clockwise direction to select the

desired characters.

( A B C . . . Z < > + − ′ /

0 1 2 3...9 “ ”Space )

B. Press theto move the flashing cursor to the next position. If you press, the flashing cursor moves to the left.

C.Repeat steps A. and B. to complete entering the entire name 8 characters max.

 

Tip

 

 

 

 

To erase/correct a name, press the DISP

for more than 2

 

seconds to clear the character and re-enter.

 

4.

Press the

MUTE / SENS to store the station name.

 

5.

The station name flashes.

 

 

To return to the normal radio reception, Press

DISP .

Erasing the station names

 

 

1.

Tune in any station and press the DISP

for more than 2

2.

seconds.

 

 

 

Press the

MUTE / SENS .

 

 

3.

The station name or “ _ _ _ _ _ _ _ _ ” flashing.

 

Rotate the dial to select the name of the station that you

 

want to erase. To erase all the names of the stations, dis-

4.

play “ ALL DEL ”.

 

 

Press the

DISP for more than 2 seconds.

 

5.

Repeat steps 3. and 4. if you want to erase other names.

To return to the normal radio reception, Press

DISP .

Direct Access to Memorized Stations via Station call

You can search for the memorized AM & FM station names in the memory.

1.

Press the

DISP to display the “ STN CALL ” on the dis-

2.

play window.

Rotate the large dial to select the desired station name.

3.

Press the

MUTE / SENS to tune in the desired station.

Level Meter selection

The meter displays can be selected from four types.

You can select :

METER 1 : The level meter goes upward.

METER 2 : Only the very top segment lights.

METER 3 : The remaining segments light. (opposite of

 

METER 2)

• METER 4

: The level meter goes up and down dividing

 

from the center segment.

• METER 0

: No meter is indicated.

1. Press the

DISP to display the “ METER 1 ” on the display

window.

 

2. Rotate the dial in a clockwise direction to select the desired meter indication.

METER 1 METER 2 METER 3 METER 4 METER 0

L-chLevel meter

R-chLevel meter

Level Meter Sensitivity selection

The sensitivity of the level meter display can be switched.

You can select :

LEVEL 1 : Normal sensitivity.

LEVEL 2 : High sensitivity.

1. Press theDISP to display the “ LEVEL 1 ” on the display window.

2. Rotate the dial to select the desired meter sensitivity.

LEVEL 1

LEVEL 2

Enhancing the bass sound

For extended bass centered @ 72Hz, Blaupunkt’s X-Bassfunction can be set for either each band and CD mode.

You can select :

X-Bass1 : Enhanced BASS level (low).

X-Bass2 : Enhanced BASS level (Middle).

X-Bass3 : Enhanced BASS level (High).

X-Bass4 : Enhanced BASS level (Very high).

X-Bass0 : No BASS enhanced.

Press the XBASS repeatedly to select the bass sound. “” appears on the display window.

Each time you press XBASS , the current mode appears on the display window and the mode change as follows:

XBASS 0 XBASS 1 XBASS 2 XBASS 3 XBASS 4

Note

Reduce XBASS levels if your combination of speakers and addon amplifiers sound distorted at the preferred sound level.

E-6

TUN/ TRK
TUN/TRK

CD Operations

Turn on/off message edit

You can edit the turn on/off message and store it in memory. Following four messages (factory set) can be edit with 8 characters each.

Turn-onmessage

 

• MESSAGE 1

: HELLO

• MESSAGE 2

: WELCOME

Turn-offmessage

 

• MESSAGE 3

: SEE YOU

• MESSAGE 4

: GOOD-BYE

1.

Repeatedly press the DISP to display the “ MESSAGE ”

2.

on the display window.

Rotate the dial to select the desired message you want

 

to edit.

 

MESSAGE1 MESSAGE2 MESSAGE3 MES-

3.

SAGE4

Press the MUTE / SENS , then enter the character.

A.Rotate the dial in a clockwise direction to select the desired characters.

( A B C . . . Z < > + - ′ /0 1 2 3...9 “ ”Space )

B. Press theto move the flashing cursor to the next position. If you press, the flashing cursor moves to the left.

C.Repeat steps A. and B. to complete entering the entire message 8 characters max.

 

Tip

 

To erase/correct a message, press the DISP for more than

 

2 seconds to clear the character and re-enter.

4.

Press the MUTE / SENS to store the message.

5.

The new message flashes.

To return to the normal radio reception, Press DISP .

Note

If you make no button input or dial operation in 20 seconds, the message edit mode will turn off automatically.

Erasing the turn on/off message

You can erase the turn on/off message if so desired.

1.

Repeatedly press the DISP to display the MESSAGE, then

2.

rotate the dial to select the message you want to erase.

Press the MUTE / SENS.

3.

The message flashing.

Press the DISP for more than 2 seconds.

 

Repeat steps 1. and 3. if you want to erase other mes-

4.

sage.

To return to the normal radio reception, Press DISP .

Demonstration mode

The unit shows a demonstration of each function.

When a demonstration is finished, it begins again after 10 seconds, and this is repeated.

1.

Press the

PWR

to turn off the unit.

2.

Press the

DISP

and 1 simultaneously for more than 2

seconds to activate the demonstration mode.

Press both button again for more than 2 seconds to cancel this mode.

Playing the CD player

Loading Discs

1. Press theOPEN and insert the disc.

2. Close the front panel. Playback begins automatically.

‘‘ LOADING ’’ indicator will flash in the display window.

Note

Make sure that the front panel is closed when playback begins.

Playback with the front panel open causes the unit to turn off automatically in about 10 minutes.

Labeled side up

! NEVER Insert a 3-inchCDs.

This unit is designed for playback of standard 5-inchCD’s only. Do not attempt to use3-inchCD singles in this unit, either with or without an adaptor, as damage to the player and/or disc may occur.

Tips

When a CD is loaded, theon the display remains lit.

During playback of a CD, the pie-shapedsignal-strengthmeterspins.

ENGLISH

FRANÇAIS

PORTUGUÊS ESPAÑOL

E-7

TUN/TRK
TUN/TRK

CD Changer Controls

ENGLISH

FRANÇAIS

PORTUGUÊS ESPAÑOL

Listening to a disc that is already loaded

Press the

CD

to select the CD mode.

Playback begins automatically.

Pausing Playback

Press the

6/ .

 

To resume playback, press the 6/ again.

Stopping Playback

Press the

BND / TS

to select the radio reception (FM I, FMII,

FT or AM, AT).

Ejecting Discs

Press theto eject the disc located behindflip-downfront panel.

Notes

The unit will turn on automatically when a CD is inserted if the ignition switch is ‘‘ON’’.

When the disc is ejected from the CD slot, remove it within 10 seconds; otherwise, the disc will be reloaded automatically.

Track Search

Press theduring CD mode. Track numbers appear in the display window.

: Playback starts from the beginning of the next track.

: Playback starts from the beginning of the current track. Press again to play the previous track.

Cue / Review

Press and hold the

TUN/TRK

. Release when you have found

the desired point.

 

 

: To search forward.

: To search backward.

Scan Play

Press the SC/PS during CD mode.

The ‘‘ SCAN ON’’ indicator appears in the display window. This will play the first 10 seconds of all the tracks on the disc. Press the SC/PS again to cancel this feature.

Repeat Play

Press the 5/RPT during CD mode.

The ‘‘ RPT ON’’ indicator appears in the display window and the current track is played repeatedly.

Press the 5/RPT again to cancel this feature.

Mix Play

Press the 4/MIX during CD mode.

The ‘‘ MIX ON’’ indicator appears in the display window.

All the tracks on the current disc are played in random order. Press the 4/MIX again to cancel this feature.

Playing the CD Changer

This product can control a Blaupunkt CD changer. Please check with your nearest car stereo specialist for recommendations of the models that will work with this radio (See page 1).

Press the CD to switch the CD changer mode. Disc No, Track No, and Track time appear on the display window and playback begins automatically. Press again to change back tobuilt-inCD operation.

Disc Select

Press the Disc select buttons to select the desired disc for play.

+ / 2

:

To advance to a higher number disc.

- /1

:

To return to a lower number disc.

Track Search

Press the .

Track numbers appear in the display window.

: Playback starts from the beginning of the next track.

: Playback starts from the beginning of the current track. Press again to play the previous track.

Cue / Review

Press and hold the

TUN/TRK

. Release when you have found

the desired point.

 

 

: To search forward.

: To search backward.

Track / Disc Scan Play

Track Scan

Press the SC/PS .

The ‘‘ SCAN ON ’’ indicator appears in the display window. This will play the first 10 seconds of all the tracks on the disc. Press the SC/PS again to cancel this feature.

E-8

MUTE / SENS
TUN/ TRK
TUN/TRK

Disc Scan

Press the SC/PS for more than 2 seconds.

The ‘‘ DSCAN ON ’’ indicator appears in the display window. This will play the first 10 seconds of the first track on each disc. Press the SC/PS again to cancel this feature.

Track / Disc Repeat Play

Track Repeat

Press the 5/RPT .

The ‘‘ RPT ON ’’ indicator appears in the display window and the current track is played repeatedly.

Press the 5/RPT again to cancel this feature.

Disc Repeat

Press the 5/RPT for more than 2 seconds.

The ‘‘ DRPT ON ’’ indicator appears in the display window and the current disc will be continually repeated.

Press the 5/RPT again to cancel this feature.

Track / Disc Mix Play

Track Mix

Press the 4/MIX .

The ‘‘ MIX ON ’’ indicator appears in the display window.

All the tracks on the current disc are played in random order.

Press the

4/MIX

again to cancel this feature.

Disc Mix

 

 

Press the

4/MIX

for more than 2 seconds.

The ‘‘ DMIX ON ’’ indicator appears in the display window. Both discs and tracks will be played in random order. Press the 4/MIX again to cancel this feature.

Tip

 

During Disc scan, Disc Repeat or Disc Mix, the

will be lit

on the display.

 

Storing the CDC disc names

You can label each disc with a personalized name. As many as 99 disc names can be stored, composed with 7 characters each.

Storing the CDC disc names

1. Play the CD and press theDISP for more than 2 seconds. The “ NAME EDT ” will light then the “ _ _ _ _ _ _ _

” on the display window. The first “ _ ” flashes.

2.Enter the characters.

A.Rotate the dial in a clockwise direction to select the desired characters.

( A B C . . . Z < > + -/0 1 2 3...9 “ ”Space )

B. Press theto move the flashing cursor to the next position. If you press, the flashing cursor moves to the left.

C.Repeat steps A. and B. to complete entering the entire name 7 characters max.

Tip

To erase/correct a name, press the DISP for more than 2 seconds to clear the character andre-enter.

3.

Press the MUTE / SENS to store the disc name.

4.

The disc name flashes.

To return to the normal CD playback mode, Press DISP .

Erasing the CDC disc names

1. Press theDISP for more than 2 seconds during CD changer mode.

2. Press the.

The disc name or “ _ _ _ _ _ _ _ ” is now flashing.

3. Rotate the dial to select the name that you want to erase. To erase all the name, display “ ALL DEL ”.

4. Press theDISP for more than 2 seconds.

Repeat steps 3. and 4. if you want to erase other names.

5. To return to the normal CD playback mode, PressDISP .

Direct Access to Memorized Disc Names via Disc call

You can search for the memorized disc names in the memory.

1.

Press the DISP to display the “ DSC CALL ” on the dis-

2.

play window.

Rotate the large dial to select the desired disc name.

3.

Press the MUTE / SENS to start playback for the desired disc.

ENGLISH

FRANÇAIS

PORTUGUÊS ESPAÑOL

E-9