Black & Decker FS6000FD, FS8000HD, FS6500HD, FS7000D User Manual

0 (0)
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZADE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
INSTRUCTION MANUAL
3333////8888"""" ((((11110000MMMMMMMM)))) AAAANNNNDDDD 1111////2222"""" ((((11113333MMMMMMMM))))
DDDDRRRRIIIILLLLLLLLSSSS AAAANNNNDDDD HHHHAAAAMMMMMMMMEEEERRRR DDDDRRRRIIIILLLLLL
LL
SS
SS
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A
BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE
A SUGGESTION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
Catalog Numbers
FS6000FD FS6500HD FS7000D FS8000HD
Catalog Number FS7000D Shown
T
T
HANK
HANK
YOU
YOU
FOR
FOR
CHOOSING
CHOOSING
F
F
IREST
IREST
ORM
ORM
! G
! G
OOTTO
O
WWW
WWW
.F
.F
IREST
IREST
ORMT
ORMT
OOLS
OOLS
.
.
COM
COM
/P
/P
RODUCT
RODUCT
R
R
EGISTRA
EGISTRA
TION
TION
TTOOREGISTER
REGISTER
YOUR
YOUR
NEW
NEW
PRODUCT
PRODUCT
.
.
635040-03 FS drills 4/25/06 1:56 PM Page 1
General Safety Rules
WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) Work area safety a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust
. Power tools create sparks which may ignite
the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions
can cause you to lose control
2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools.
Unmodified
plugs and matching outlets will reduce risk of electric shock
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool
will increase the risk of electric shock
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric
shock.
3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tool
may result in serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off-position before
plugging in.
Carrying power tools with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should also be avoided.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
Use of these devices
can reduce dust-related hazards.
4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was designed.
2
635040-03 FS drills 4/25/06 1:56 PM Page 2
3
b) Do not use the power tool if the switch does not turn it on and off.
Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use.
Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these
instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed.
Use of the power tool for operations different from those intended could result in a hazardous situation.
5) Service a) Have your power tool serviced by a qualified repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is maintained.
SPECIFIC SAFETY RULES
a) Hold tool by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring or its own cord.
Contact with a "live"
wire will make exposed metal parts of the tool "live" and shock the operator.
b) Use clamps or another practical way to secure and support the work piece to
a stable platform.
Holding the work by hand or against your body leaves it
unstable and may lead to loss of control.
c) Wear ear protectors with impact drills.
Exposure to noise can cause hearing
loss.
d) Use auxiliary handles supplied with the tool.
Loss of control can cause personal
injury.
e) Hammer bits and tools get hot during operation.
Wear gloves when touching
them.
WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
ANSI Z87.1 eye protection (CAN/CSA Z94.3)
ANSI S12.6 (S3.19) hearing protection
NIOSH/OSHA/MSHA respiratory protection
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA). Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or
lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
635040-03 FS drills 4/25/06 1:56 PM Page 3
The label on your tool may include the following symbols.
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min........................minutes ......................alternating
current
......................direct current
n
o ........................no load speed
..........................
Class II Construction
........................earthing terminal
........................safety alert symbol .../min ..................revolutions or
reciprocations per minute
bpm.....................beats per minute
Extension Cords
When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
4
FS6000FD
FUNCTIONAL DESCRIPTION
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Two-gear selector
5. Drilling mode selector
6. Chuck
7. Chuck key
8. Depth stop
9. Side handle
10. Belt clip
11. Fast drive remov. chuck
12. Bit storage
2
3
1
2
3
1
2
3
1
2
3
1
6
11
6
6
9
5
10
9
12
5
FS6500HD
FS7000D
FS8000HD
9
8
7
12
4
10
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gage Than Than 0-6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended
635040-03 FS drills 4/25/06 1:56 PM Page 4
5
8
9
A
B
9
8
14
13
6
C
F
6
7
16
17
15
6
E
D
635040-03 FS drills 4/25/06 1:56 PM Page 5
6
Safety Warnings and Instructions: Drills
WARNING: Shock hazard. When drilling or driving into walls, floors or wherever live electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the plastic handle(s) to prevent shock.
• Do not lock the tool ON when drilling by hand. Refer to Operating Instructions-Switch.
Hold drill firmly with both hands to control the twisting action of the drill. If your drill
is equipped with a side handle, always use the side handle.
WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting.
• Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly.
Motor
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your drill will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that your tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply.
I
20
4
H
5
18
19
G
6
7
15
17
635040-03 FS drills 4/25/06 1:56 PM Page 6
7
Assembly
WARNING: To reduce the risk of injury, before assembly, make sure that the tool is
switched off and unplugged.
Attaching the side handle - FS6500HD, FS7000D, FS8000HD (fig. A)
If your drill is equipped with a side handle, it must be installed properly to control the drill
• Turn the grip counterclockwise until you can slide the side handle (9) onto the front of the
tool as shown.
• Rotate the side handle into the desired position.
• Insert the depth stop (8) into the mounting hole as shown (FS6500HD, FS8000HD).
• Set the drilling depth as described under “Setting the Drilling Depth” (FS6500HD, FS8000HD).
• Tighten the side handle by turning the grip clockwise.
Inserting a drill bit or other accessory (fig. B & C)
WARNING: Do not attempt to tighten drill bits (or any other accessory) by
gripping the front part of the chuck and turning the tool on.
Damage to the chuck
and personal injury may occur when changing accessories.
WARNING: Always ensure the bit is secure before starting the tool.
A loose bit
may eject from tool causing possible personal injury.
Keyless chuck (FS6000FD with Fast Drive) (fig. B)
• Open the chuck (6) by grasping the rear half (13) with one hand and use your other hand
to rotate the front sleeve (14) counterclockwise.
• Insert the accessory shaft into the chuck to about 3/4” (19 mm) depth, centered in the
jaws.
• Tighten securely by holding the rear half of the chuck and rotating the front sleeve in the
clockwise direction as viewed from the chuck end.
Keyless chuck with spindle lock (FS6500HD, FS8000HD)
This tool is equipped with a feature that automatically locks the spindle when the tool is not running. This feature is a normal condition which allows for tightening or loosening of the chuck with one hand while holding the drill with the other.
• Open the chuck (6) by turning the sleeve (13) counterclockwise.
• Insert the accessory shaft into the chuck to about 3/4” (19 mm) depth, centered in the
jaws.
• Tighten securely by turning the sleeve clockwise as viewed from the chuck end.
Chuck and key (FS7000D) (fig. C)
• Open the chuck (6) by turning the collar counterclockwise (when viewed from the chuck
end).
• Insert the accessory shaft into the chuck to about 3/4” (19 mm) depth, centered in the
jaws.
• Tighten chuck collar by hand. Place chuck key (7) into each of the three holes and
securely tighten in a clockwise direction.
NOTE: Tighten chuck with all three holes to prevent slippage.
Removing and attaching the chuck (fig. D, E, F, G)
Fast Drive Bit Change System (FS6000FD)
A unique feature of the FS6000FD is the ability to remove the chuck quickly and easily. This allows for a drill bit to be in the keyless chuck, while another accessory such as a screwdriver bit, can be inserted into the Fast Drive hex shaft at the same time.
To remove the chuck:
1. Grasp the drill and depress the two orange buttons on the chuck collar as shown in figure D.
2. With the buttons depressed, pull straight out.
To replace the chuck:
1. Push the Fast Drive chuck straight on with a slight twisting motion until you hear it click into place.
To insert a screwdriver bit into the Fast Drive hex shaft, push the bit in until you hear it click into place. To remove the bit, hold the drill as shown in figure E. Push in evenly on the spring loaded disc with two fingers and pull the bit straight out.
Keyless chuck (FS6500HD, FS8000HD) (fig. F)
• Open the chuck (6) as far as possible.
635040-03 FS drills 4/25/06 1:56 PM Page 7
8
• Remove the chuck retaining screw (15), located in the chuck, by turning it clockwise using a screwdriver (lefthand thread).
• Tighten an Allen key (16) of 1/4” or greater size (not supplied) into the chuck and strike it with a soft hammer (17) in a clockwise direction as shown
• Remove the Allen key.
• Remove the chuck by turning it counterclockwise.
• To attach the chuck, screw it onto the spindle and secure it with the chuck retaining screw.
Keyed chuck (FS7000D)
(fig. G)
NOTE: Before attempting to remove chuck, shift the drill into the drilling mode (not hammer, if so equipped).
• Place chuck key (7) in any one of the three holes in the chuck (6).
• Using a soft hammer (17), strike the key in a clockwise direction. This will loosen the screw (15) inside the chuck.
• Open chuck jaws fully and remove the chuck retaining screw, located in the chuck, by turning it clockwise using a screwdriver (lefthand thread).
• Place key in chuck. Using a soft hammer (17), strike key sharply in a counterclockwise direction.
• Remove the chuck by turning it counterclockwise.
• To attach the chuck, screw it onto the spindle and secure it with the chuck retaining screw.
Belt clip (FS6000FD, FS7000D)
WARNING: When using the belt clip (10) to transport the tool, do not leave an
accessory in the chuck.
Operating Instructions
WARNING: To reduce the risk of serious personal injury,
read, understand and
follow all safety warnings and instructions prior to using tool.
WARNING: It is important to support the work properly and to hold the drill firmly
to prevent loss of control which could cause personal injury.
If you have any
questions on how to properly operate tool, call: 1-800-544-6986.
WARNING: Do not attempt to tighten drill bits (or any other accessory) by
gripping the front part of the chuck and turning the tool on.
Damage to the chuck and
personal injury may occur when changing accessories.
WARNING: To reduce the risk of injury,
always unplug drill from power supply before
making any adjustments or changing accessories.
WARNING: To reduce the risk of injury,
let the tool work at its own pace. Don’t overload.
Selecting the direction of rotation (FS6000FD, FS6500HD)
For drilling and for tightening screws, use forward (clockwise) rotation. For loosening screws or removing a jammed drill bit, use reverse (counterclockwise) rotation.
Note: The direction of rotation is also depicted by an arrow on the drill housing.
WARNING: Never change the direction of rotation while the motor is running.
• To select forward rotation, push the forward/reverse slider (3) to the right (when viewed from the chuck end).
• To select reverse rotation, push the forward/reverse slider (3) to the left (when viewed from the chuck end).
Selecting the direction of rotation (FS7000D, FS8000HD)
For drilling and for tightening screws, use forward (clockwise) rotation. For loosening screws or removing a jammed drill bit, use reverse (counterclockwise) rotation.
WARNING:Never change the direction of rotation while the motor is running.
To select forward rotation, push the forward/reverse slider (3) to the left (when viewed from the chuck end).
To select reverse rotation, push the forward/reverse slider (3) to the right (when viewed from the chuck end).
Note: The direction of rotation is also depicted by an arrow on the drill housing.
WARNING: Never change the direction of rotation while the motor is running.
Selecting the drilling mode (FS6500HD, FS8000HD) (fig. H)
For drilling in masonry, set the drilling mode selector (5) to the “hammer symbol” (18) position.
635040-03 FS drills 4/25/06 1:56 PM Page 8
9
For drilling in other materials and for screwdriving, set the drilling mode selector (5) to the
“drill symbol” (19) position.
Two-gear selector (FS8000HD) (fig. I)
For drilling in steel and for screwdriving applications, turn the two-gear selector (4) into
position 1 by aligning the number with the mark on the housing (20) (1st gear). Also when using larger diameter bits in wood turn the two gear selector into position 1.
For drilling in materials other than steel and when using smaller diameter bits, turn the
two-gear selector (4) into position 2 by aligning the number with mark on the housing (20) (2nd gear).
Setting the drilling depth (FS6500HD, FS8000HD)
Slacken the side handle (9) by turning the grip counterclockwise.
Set the depth stop (8) to the desired position. The maximum drilling depth is equal to the
distance between the tip of the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
Switching on and off
• To switch the tool on, press the variable speed switch (1). The tool speed depends on how far you press the switch.
• For continuous operation, press the lock-on button (2) and release the variable speed switch. This option is available only at full speed.
• To switch the tool off, release the variable speed switch. To switch the tool off when in continuous operation, press the variable speed switch once more and release it.
WARNING: The drill should only be locked ON when it is held stationary in a drill press stand or other means; NOT BY HAND! Never unplug the tool with the locking feature engaged. To do so will cause the tool to start immediately the next time it is plugged in.
Drilling
• Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly.
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the Safety Instructions.
• Use appropriate and required safety equipment, as instructed in the safety instructions.
• Secure and maintain work area, as instructed in the safety instructions.
• Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.
• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit.
• Hold the drill firmly with both hands to control its twisting action.
Drills (FS6500HD, FS7000D, FS8000HD) equipped with a side handle must be used.
• DO NOT CLICK THE TRIGGER OF A STALLED DRILLOFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.
• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.
Drilling In Wood
Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes.
Drilling In Metal
Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.
Drilling in Masonry (Shift drill into hammer mode if so equipped)
Use carbide tipped masonry bits. Refer to
Drilling
section. Keep even force on the drill but not so much that you crack the brittle material. Asmooth, even flow of dust indicates the proper drilling rate.
635040-03 FS drills 4/25/06 1:56 PM Page 9
10
TROUBLESHOOTING
Problem Possible Cause Possible Solution
• Unit will not start. • Cord not plugged in. • Plug tool into a working outlet.
• Forward/reverse slider not fully • Push slider completely to depressed in desired direction. the left or right.
• Circuit fuse is blown. • Replace circuit fuse. (If the product repeatedly
causes the circuit fuse to blow, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.)
• Circuit breaker is tripped. • Reset circuit breaker. (If the product repeatedly
causes the circuit breaker to trip, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.)
• Cord or switch is damaged. • Have cord or switch replaced at Black & Decker Service Center or Authorized Servicer.
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986. MMAAIINNTTEENNAANNCCEE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:
1-800-544-6986.
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their
635040-03 FS drills 4/25/06 1:56 PM Page 10
11
specific return policy regarding returns that are beyond the time set for exchanges. The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.
SPECIAL WARRANTY NOTE TO CONTRACTORS:
FIRESTORM
TM
branded products are offered as high end consumer home use tools and carry a HOME USE WARRANTY. These tools are designed, manufactured and tested to meet or exceed the needs of the do-it-yourselfer in the execution of projects and repairs in and around the home. With proper use they will provide the home owner with step up power and performance well beyond their two year warranty. However, if you use tools for a living and use FIRESTORMTMbranded products or any of Black & Decker’s other Consumer Home Use tools ON THE JOBSITE you should know that they CANNOT BE
COVERED UNDER OUR WARRANTY.
MAXIMUM RECOMMENDED CAPACITIES
Cat. # Type Steel Soft Wood Hard Wood Masonry
FS6000FD 3/8"Drill 3/8"(9.5mm) Twist Bit 1-1/4"(31.7mm) 1"(25.4mm) N/A
FS6500HD 1/2"Hammer Drill 1/2"(12.7mm) Twist Bit 1"(25.4mm) 1/2"(12.7mm) 1/2"(12.7mm)
FS7000D 1/2" Drill 1/2"(12.7mm) Twist Bit 1-1/2"(38.1mm) 1-1/4"(31.7mm) N /A
FS8000HD 1/2"Hammer Drill 1/2"(12.7mm) Twist Bit 1-1/2"(38.1mm) 1-1/4"(31.7mm) 1/2"(12.7mm)
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
635040-03 FS drills 4/25/06 1:56 PM Page 11
12
N° de catalogue
FS6000FD
FS6500HD
FS7000D
FS8000HD
CONSERVER CE MANUEL POUR UN USAGE ULTÉRIEUR.
AVANT DE RETOURNER CE PRODUIT POUR
QUELQUE RAISON QUE CE SOIT, COMPOSER LE
1-800-544-6986
AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LAPLUPART
DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR
TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS
IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.
M
M
ERCI
ERCIDD
AAVOIR
VOIR
CHOISI
CHOISI
F
F
IREST
IREST
ORM
ORM
!
!
V
V
ISITEZ
ISITEZ
WWW
WWW
.F
.F
IREST
IREST
ORMT
ORMT
OOLS
OOLS
.
.
COM
COM
/P
/P
RODUCT
RODUCT
R
R
EGISTRA
EGISTRA
TION
TION
POUR
POUR
ENREGISTRER
ENREGISTRER
VOTRE
VOTRE
NOUVEAU
NOUVEAU
PRODUIT
PRODUIT
.
.
GUIDE D’UTILISATION
PPPPEEEERRRRCCCCEEEEUUUUSSSSEEEESSSS EEEETTTT MMMMAAAARRRRTTTTEEEEAAAAUUUUXXXX
PPPPEEEERRRRFFFFOOOORRRRAAAATTTTEEEEUUUURRRRSSSS
11110000MMMMMMMM ((((3333////8888PPPPOOOO)))) 11113333MMMMMMMM ((((1111////2222PPPPOOOO))
))
Numéro de catalogue FS7000D illustré
635040-03 FS drills 4/25/06 1:56 PM Page 12
Loading...
+ 28 hidden pages