Black & Decker 388268, ET1255, ET1245, ET1265, ET1275 User Manual

0 (0)

Snap-on Drill 11/12/03 8:47 AM Page 1

Snap-on Drill 11/12/03 8:47 AM Page 2

Snap-on Tool Corporation, Kinosha, WI

Form# 388268

Black & Decker 388268, ET1255, ET1245, ET1265, ET1275 User Manual

Snap-on Drill 11/12/03 8:47 AM Page 3

USERS INSTRUCTION MANUAL

ET1265

ET1255

ET1245

ET1275

PROFESSIONAL

1/2” VSR DRILL

Snap-on Drill 11/12/03 8:47 AM Page 4

English

General Safety Rules

WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.

Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

Don’t expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W.” These cords are rated for outdoor use and reduce the risk of electric shock. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next

heavier gage. The smaller the gage number, the heavier the cord.

 

 

 

Minimum Gage for Cord Sets

 

 

 

Volts

 

Total Length of Cord in Feet

 

 

 

120V

 

0-25

26-50

51-100

101-150

 

 

240V

 

0-50

51-100

101-200

201-300

 

 

Ampere Rating

 

AWG

 

 

 

 

More

Not more

 

 

 

 

 

Than

Than

 

 

 

 

 

0

-

6

18

16

16

14

 

6

-

10

18

16

14

12

 

10

-

12

16

16

14

12

 

12

-

16

14

12

Not Recommended

 

 

 

 

 

 

 

 

 

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury,

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught in moving parts.

Avoid accidental starting. Be sure switch is off before

Snap-on Drill 11/12/03 8:47 AM Page 1

plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

Remove adjusting keys or switches before turning the tool on.

A wrench or key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean.

Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using.

Many accidents are caused by poorly maintained tools.

1

Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

SERVICE

Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual.

Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

Additional Safety Rules

Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.

Keep handles dry, clean, free from oil and grease. It is recommended to use rubber gloves. This will enable better control

DO NOT TOUCH ANY METAL PARTS OF THE TOOL when drilling or driving into walls, floors or wherever live electrical wires may be encountered. Hold the tool only by insulated grasping surfaces to prevent electric shock if you drill or drive into a live wire.

CAUTION: Wear appropriate personal hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

English

Snap-on Drill 11/12/03 8:47 AM Page 2

English

• arsenic and chromium from chemically-treated lumber (CCA).

FIG. 1

FIG. 2

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

The label on your tool may include the following symbols.

V ..........

volts

A..........

amperes

 

 

Hz ..........

hertz

W ........

watts

 

 

min ........

minutes

no ........

alternating current

A

REVERSING

........

direct current

no load speed

LEVER

............

Class II

/min ....

revolutions per minute

 

(Shown in Forward

..............

Construction

........

earthing

 

Position)

..........

safety alert symbol

............

terminals

 

 

Motor Brushes

Snap-on uses an advanced brush system which automatically stops

the drill when the brushes wear out. This prevents serious damage to FIG. 3 the motor.

Switch

To start drill, depress trigger switch; to stop Drill, release trigger. To lock trigger in ON position for continuous operation, depress trigger and push up locking button “A” Figure 1, then gently release trigger. To release locking mechanism, depress trigger fully, then release it. Before using the tool (each time) be sure that the locking button release mechanism is working freely.

Do not lock the switch ON when drilling by hand so that you can instantly release the trigger switch if the bit binds in the hole.

The locking button is for use only when the drill is mounted in a drill press stand or otherwise held stationary.

Be sure to release the locking button before disconnecting the plug from the power supply. Failure to do so will cause the tool to start

2

SWITCH

ASSEMBLY

LOCK-OUT KEY

Snap-on Drill 11/12/03 8:47 AM Page 3

FIG. 4

SPINDLE LOCK

BUTTON

immediately the next time it is plugged in. Damage or injury could result.

THE VARIABLE SPEED TRIGGER SWITCH permits speed control

– the farther the trigger is depressed, the higher the speed of the drill. NOTE: Use lower speeds for starting holes without a center punch, drilling in metal or plastics, driving screws or drilling ceramics. Higher speeds are better for drilling wood and composition boards, and for using abrasive and polishing accessories.

THE REVERSING LEVER The reversing lever is used when backing out screws and jammed drill bits. To operate the tool in reverse, release the trigger switch and push the lever to the left (when viewed from the chuck end) as shown in Figure 2. To operate the drill in forward for drilling holes or driving screws (as well as other accessories) release the trigger switch and push the lever to the right (when viewed from the chuck end).

Return the reversing lever to the forward position after all operations in reverse are completed.

SWITCH LOCK-ON

Your drill is equipped with a switch lock-on feature. If you wish to disable this feature, take your tool to any authorized service center.

3

The service center can provide a lock-out key to prevent the unit from being locked in the “ON” position (Figure 3).

Operation

DRILLING

1.Always unplug the drill when attaching or changing bits or accessories.

2.Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws. For METAL, use high speed steel twist drill bits or hole saws. For MASONRY, such as brick, cement, cinder block, etc., use carbide-tipped bits.

3.Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the material.

4.Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting, but do not push hard enough to stall the motor or deflect the bit.

5.Hold tool firmly to control the twisting action of the drill.

6.IF DRILL STALLS, it is usually because it is being overloaded or improperly used. RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK

TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL — THIS CAN DAMAGE THE DRILL.

7.To minimize stalling or breaking through the material, reduce pressure on drill and ease the bit through the last fractional part of the hole.

8.Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent jamming.

9.With Variable Speed Drills there is no need to center punch the point to be drilled. Use a slow speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep enough to drill without the bit skipping out.

English

Loading...
+ 14 hidden pages