Black & Decker DR550, DR330, DR650, DR350KG User Manual

5 (1)

638911-00 02 DR drills 3/20/08 10:20 AM Page 1

3/8 INCH (10MM) 1/2 INCH (13MM) DRILLS & HAMMER DRILLS

INSTRUCTION MANUAL

Catalog Numbers

DR250,

DR320KG,

DR330, DR550,

DR650

Catalog Number DR250 Shown

THANK YOU FOR CHOOSING BLACK & DECKER!

GO TO WWW.BLACKANDDECKER.COM/NEWOWNER

TO REGISTER YOUR NEW PRODUCT.

BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No.AND DATE CODEAVAILABLE. IN MOST CASES,A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVEA SUGGESTION OR COMMENT, GIVE USACALL. YOUR FEEDBACK IS VITALTO

BLACK & DECKER.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

638911-00 02 DR drills 3/20/08 10:20 AM Page 2

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1)Work area safety

a)Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b)Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c)Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2)Electrical safety

a)Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

b)Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c)Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

d)Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e)When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f)If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3)Personal safety

a)Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

b)Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c)Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d)Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e)Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f)Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g)If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

2

638911-00 02 DR drills 3/20/08 10:20 AM Page 3

4)Power tool use and care

a)Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was designed.

b)Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c)Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d)Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e)Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f)Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g)Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5)Battery tool use and care

a)Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

b)Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

c)When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

d)Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

6)Service

a)Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.

Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.

Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

Use clamps or another practical way to secure and support the work piece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

Hammer bits and tools get hot during operation. Wear gloves when touching them.

3

638911-00 02 DR drills 3/20/08 10:20 AM Page 4

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

ANSI Z87.1 eye protection (CAN/CSA Z94.3)

ANSI S12.6 (S3.19) hearing protection

NIOSH/OSHA/MSHA respiratory protection

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual.

The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

SYMBOLS

 

 

 

 

 

The label on your tool may include the following symbols.

 

V ..........................

volts

A..........................

amperes

Hz ........................

hertz

W ........................

watts

min........................

minutes

 

 

......................

alternating

 

 

 

 

no

current

 

 

 

direct current

no load speed

 

 

......................

 

..........................

 

Class II Construction

 

 

........................

earthing terminal

 

 

 

 

 

 

 

........................

 

safety alert symbol

 

 

 

 

.../min....................

revolutions or

bpm.....................

beats per minute

 

 

 

reciprocations

 

 

 

 

 

 

 

per minute

 

 

 

 

4

638911-00 02 DR drills 3/20/08 10:20 AM Page 5

Extension Cords

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

 

 

 

Minimum Gage for Cord Sets

 

Volts

 

Total Length of Cord in Feet

120V

 

0-25

26-50

51-100

101-150

 

 

 

(0-7,6m)

(7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V

 

0-50

51-100

101-200

201-300

 

 

 

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

 

 

 

 

More

 

Not more

American Wire Gage

 

Than

 

Than

 

 

 

 

0

-

6

18

16

16

14

6

-

10

18

16

14

12

10

-

12

16

16

14

12

12

-

16

14

12

Not Recommended

 

 

 

 

 

 

 

FUNCTIONAL

 

 

 

12

 

 

DR320KG

12 10

 

 

DR250

 

 

DESCRIPTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Variable speed switch

 

 

 

 

 

 

6

 

 

2.

Lock-on button

6

 

3

 

3

 

 

 

 

 

 

 

3.

Forward/reverse

 

 

 

1

 

 

 

 

1

 

4. Two-gear selector

 

 

 

 

 

 

 

 

 

 

5.

Drilling mode selector

 

 

 

 

 

 

 

 

 

 

6. Chuck

 

 

 

 

 

 

 

 

 

 

 

 

DR330

12

10

 

 

DR550

 

 

 

 

 

 

 

 

 

 

7. Chuck key

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8. Depth stop

 

 

 

 

 

 

6

3

 

 

 

6

 

 

 

 

 

9.

Side handle

 

 

3

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

10. Belt clip

 

 

 

1

2

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11. Clutch

 

 

 

 

 

 

 

 

7

12. Bit storage

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

Black & Decker DR550, DR330, DR650, DR350KG User Manual

638911-00 02 DR drills 3/20/08 10:20 AM Page 6

 

 

A

DR650

5

8

 

6

3

9

4

 

2

 

 

1

 

9

7

 

B

 

C

 

 

6

 

 

7

14

 

 

6

13

 

 

 

D

17

15

16

6

17

7

15

6

6

638911-00 02 DR drills

3/20/08

10:20 AM

F

 

 

 

18

 

 

5

 

19

 

 

Page 7

20

4

First Aid Measures for Gel Components (DR320KG Only)

If gel within the comfort grip becomes exposed and results in skin contact wash with soap and water; for eye contact, flush with flowing water. If swallowed, seek medical attention. Material Safety Data Sheet (MSDS) available from 1-800-544-6986

Safety Warnings and Instructions: Drills

WARNING: Shock hazard. When drilling or driving into walls, floors or wherever live electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the plastic handle(s) to prevent shock.

Do not lock the tool ON when drilling by hand. Refer to Operating Instructions-Switch.

Hold drill firmly with both hands to control the twisting action of the drill. If your drill is equipped with a side handle, always use the side handle.

WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting.

Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly.

Motor

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your drill will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that your tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply.

Assembly

WARNING: To reduce the risk of injury, before assembly, make sure that the tool is switched off and unplugged.

Attaching the side handle - DR550 / DR650 (fig. A)

If your drill is equipped with a side handle, it must be installed properly to control the drill

Turn the grip counterclockwise until you can slide the side handle (9) onto the front of the tool as shown.

Rotate the side handle into the desired position.

Insert the depth stop (8) into the mounting hole as shown (DR650).

Set the drilling depth as described under “Setting the Drilling Depth (DR650)”.

Tighten the side handle by turning the grip clockwise.

7

638911-00 02 DR drills 3/20/08 10:20 AM Page 8

Inserting a drill bit or other accessory (fig. B & C)

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck

and personal injury may occur when changing accessories.

WARNING: Always ensure the bit is secure before starting the tool. A loose bit may eject from tool causing possible personal injury.

Keyless chuck (DR250) (fig. B)

Open the chuck (6) by grasping the rear half (13) with one hand and use your other hand to rotate the front sleeve (14) counterclockwise.

Insert the accessory shaft into the chuck to about 3/4 in. (19 mm) depth, centered in the jaws.

Tighten securely by holding the rear half of the chuck and rotating the front sleeve in the clockwise direction as viewed from the chuck end.

Keyless chuck with spindle lock (Soft GripTM DR320KG / DR330)

This tool is equipped with a feature that automatically locks the spindle when the tool is not running. This feature is a normal condition which allows for tightening or loosening of the chuck with one hand while holding the drill with the other. The DR320KG also has a soft grip for ease in tightening accessories.

NOTE: Move clutch to drill mode to tighten (DR330).

Open the chuck (6) by turning the sleeve (13) counterclockwise.

Insert the accessory shaft into the chuck to about 3/4 in. (19 mm) depth, centered in the jaws.

Tighten securely by turning the sleeve clockwise as viewed from the chuck end.

Chuck and key (DR550, DR650) (fig. C)

Open the chuck (6) by turning the collar counterclockwise (when viewed from the chuck end).

Insert the accessory shaft into the chuck to about 3/4 in. (19 mm) depth, centered in the jaws.

Tighten chuck collar by hand. Place chuck key (7) into each of the three holes and securely tighten in a clockwise direction.

NOTE: Tighten chuck with all three holes to prevent slippage.

Removing and attaching the chuck (fig. D)

Keyless chuck (DR250, DR320KG, DR330)

Open the chuck (6) as far as possible.

Remove the chuck retaining screw (15), located in the chuck, by turning it clockwise using a screwdriver (lefthand thread).

Tighten an Allen key (16) of 1/4 in. or greater size (not supplied) into the chuck and strike it with a soft hammer (17) in a clockwise direction as shown.

Remove the Allen key.

Remove the chuck by turning it counterclockwise.

To attach the chuck, screw it onto the spindle and secure it with the chuck retaining screw.

Keyed chuck (DR550, DR650) (fig. E)

NOTE: Before attempting to remove chuck, shift the drill into the drilling mode (not hammer, if so equipped).

Place chuck key (7) in any one of the three holes in the chuck (6).

Using a soft hammer (17), strike the key in a clockwise direction. This will loosen the screw (15) inside the chuck.

Open chuck jaws fully and remove the chuck retaining screw, located in the chuck, by turning it clockwise using a screwdriver (lefthand thread).

Place key in chuck. Using a soft hammer (17), strike key sharply in a counterclockwise direction.

Remove the chuck by turning it counterclockwise.

To attach the chuck, screw it onto the spindle and secure it with the chuck retaining screw.

Belt clip (DR320KG, DR330, DR550)

WARNING: When using the belt clip (10) to transport the tool, do not leave an accessory in the chuck.

8

638911-00 02 DR drills 3/20/08 10:20 AM Page 9

Operating Instructions

WARNING: To reduce the risk of serious personal injury, read, understand and follow all safety warnings and instructions prior to using tool.

WARNING: It is important to support the work properly and to hold the drill firmly to prevent loss of control which could cause personal injury. If you have any

questions on how to properly operate tool, call: 1-800-544-6986.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck

and personal injury may occur when changing accessories.

WARNING: To reduce the risk of injury, always unplug drill from power supply before making any adjustments or changing accessories.

WARNING: To reduce the risk of injury, let the tool work at its own pace. Do not overload.

Selecting the direction of rotation (DR250, DR320KG, DR330, DR650)

For drilling and for tightening screws, use forward (clockwise) rotation. For loosening screws or removing a jammed drill bit, use reverse (counterclockwise) rotation. Note: The direction of rotation is also depicted by an arrow on the drill housing.

WARNING: Never change the direction of rotation while the motor is running.

To select forward rotation, push the forward/reverse slider (3) to the right (when viewed from the chuck end).

To select reverse rotation, push the forward/reverse slider (3) to the left (when viewed from the chuck end).

Selecting the direction of rotation (DR550)

For drilling and for tightening screws, use forward (clockwise) rotation. For loosening screws or removing a jammed drill bit, use reverse (counterclockwise) rotation.

WARNING:Never change the direction of rotation while the motor is running.

To select forward rotation, push the forward/reverse slider (3) to the left (when viewed from the chuck end).

To select reverse rotation, push the forward/reverse slider (3) to the right (when viewed from the chuck end).

Note: The direction of rotation is also depicted by an arrow on the drill housing.

WARNING: Never change the direction of rotation while the motor is running.

Selecting the drilling mode (DR650) (fig. F)

For drilling in masonry, set the drilling mode selector (5) to the “hammer symbol” (18) position.

For drilling in other materials and for screwdriving, set the drilling mode selector (5) to the “drill symbol” (19) position.

Two-gear selector (DR650) (fig. G)

For drilling in steel and for screwdriving applications, turn the two-gear selector (4) into position 1 by aligning the number with the mark on the housing (20) (1st gear). Also when using larger diameter bits in wood turn the two gear selector into position 1.

For drilling in materials other than steel and when using smaller diameter bits, turn the two-gear selector (4) into position 2 by aligning the number with mark on the housing (20) (2nd gear).

Setting the drilling depth (DR650)

Slacken the side handle (9) by turning the grip counterclockwise.

Set the depth stop (8) to the desired position. The maximum drilling depth is equal to the distance between the tip of the drill bit and the front end of the depth stop.

Tighten the side handle by turning the grip clockwise.

Screwdriving with clutch drill (DR330)

This tool is fitted with a collar to select the operating mode and to set the torque for tightening screws. Large screws and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials.

For drilling in wood, metal and plastics, set the collar to the drilling position symbol .

For screwdriving, set the collar to the desired setting. If you do not yet know the appropriate setting, proceed as follows:

9

638911-00 02 DR drills 3/20/08 10:20 AM Page 10

Set the collar to the lowest torque setting.

Tighten the first screw.

If the clutch ratchets before the desired result is achieved, increase the collar setting

and continue tightening the screw. Repeat until you reach the correct setting. Use this setting for the remaining screws.

Switching on and off

To switch the tool on, press the variable speed switch (1). The tool speed depends on how far you press the switch.

For continuous operation, press the lock-on button (2) and release the variable speed switch. This option is available only at full speed.

To switch the tool off, release the variable speed switch. To switch the tool off when in continuous operation, press the variable speed switch once more and release it.

WARNING: The drill should only be locked ON when it is held stationary in a drill press stand or other means; NOT BY HAND! Never unplug the tool with the locking feature engaged. To do so will cause the tool to start immediately the next time it is plugged in.

Drilling

Always move clutch to “DRILL” mode when drilling (DR330 only).

Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly.

Use sharp drill bits only.

Support and secure work properly, as instructed in the Safety Instructions.

Use appropriate and required safety equipment, as instructed in the safety instructions.

Secure and maintain work area, as instructed in the safety instructions.

Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.

Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit.

Hold the drill firmly with both hands to control its twisting action.

Drills (DR550, DR650) equipped with a side handle must be used.

DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT.

Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.

Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.

Plug in drill. Make sure switch turns drill on and off.

Drilling In Wood

Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes.

Drilling In Metal

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.

Drilling in Masonry (Shift drill into hammer mode if so equipped)

Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but not so much that you crack the brittle material. A smooth, even flow of dust indicates the proper drilling rate.

10

638911-00 02 DR drills 3/20/08 10:20 AM Page 11

 

TROUBLESHOOTING

 

Problem

Possible Cause

Possible Solution

• Unit will not start.

Cord not plugged in.

Forward/reverse slider not fully depressed in desired direction.

Circuit fuse is blown.

Plug tool into a working outlet.

Push slider completely to the left or right.

Replace circuit fuse.

(If the product repeatedly causes the circuit fuse to blow, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.)

• Circuit breaker is tripped.

• Reset circuit breaker. (If the product repeatedly causes the circuit breaker to trip, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.)

• Cord or switch is damaged.

• Have cord or switch

 

replaced at Black &

 

Decker Service Center or

 

Authorized Servicer.

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com

11

638911-00 02 DR drills 3/20/08 10:20 AM Page 12

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

MAXIMUM RECOMMENDED CAPACITIES

Cat. #

Type

Steel

Soft Wood

Hard Wood

Masonry

DR250

3/8 in. Drill

3/8 in.(9.5mm)Twist Bit

1-1/4 in.(31.7mm)

1 in.(25.4mm)

N/A

DR320

3/8 in. Drill

3/8 in.(9.5mm)Twist Bit

1-1/4 in.(31.7mm)

1 in.(25.4mm)

N/A

DR330

3/8 in. Drill

3/8 in.(9.5mm)Twist Bit

1-1/4 in.(31.7mm)

1 in.(25.4mm)

N/A

DR550

1/2 in. Drill

1/2 in.(12.7mm)Twist Bit

1-1/2 in. (38.1mm)

1-1/4 in.(31.7mm)

N/A

DR650

1/2 in.

1/2 in.(12.7mm) Twist Bit

1-1/2 in. (38.1mm)

1-1/4in.(31.7mm) 1/2 in.

Hammer Drill

 

 

 

(12.7mm)

Black & Decker (U.S.)

See ‘Tools-

Inc.,

701 E. Joppa Rd.

Electric’

Towson, MD 21286

– Yellow Pages –

U.S.A.

for Service &

 

Sales

12

Loading...
+ 28 hidden pages