Black & Decker 1 VPX VPX1201 User Manual

Size:
704.05 Kb
Download

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 1

1VPXTM DRILL DRIVER

INSTRUCTION MANUAL

THANK YOU FOR CHOOSINGBLACK& DECKER!

GO TO WWW.BLACKANDDECKER.COM/NEWOWNER

TO REGISTER YOUR NEW PRODUCT.

BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFOREYOU CALL, HAVETHE CATALOG No.AND DATE CODEAVAILABLE. IN MOSTCASES,A

BLACK & DECKER REPRESENTATIVE CAN RESOLVETHE PROBLEM OVERTHE PHONE. IFYOU HAVE

A SUGGESTION OR COMMENT, GIVE USACALL.YOUR FEEDBACK IS VITALTO BLACK & DECKER.

Catalog Number VPX1201

SAVE THIS MANUAL FOR FUTURE REFERENCE.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 2

GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to yourmains-operated(corded) power tool orbattery-operated(cordless) power tool.

SAVE THESE INSTRUCTIONS

1)Work area safety

a)Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b)Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c)Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control

2)Electrical safety

a)Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock

b)Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c)Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock

d)Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e)When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

3) Personal safety

a)Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tool may result in serious personal injury.

b)Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c)Avoid accidental starting. Ensure the switch is in the off-positionbefore plugging in.Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

d)Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e)Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f)Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should also be avoided.

g)If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust-related hazards.

4)Power tool use and care

a)Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was designed.

2

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 3

b)Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c)Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d)Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e)Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f)Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g)Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could result in a hazardous situation.

5)Battery tool use and care

a)Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into power tools that have the switch on invites accidents.

b)Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

c)Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

d)When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

e)Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

6)Service

a)Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

Hold tool by insulated gripping surfaces when performing an operation where the tool may contact hidden wiring or its own cord. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator.

Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

When working on a ladder or on scaffolding be sure to lay the tool down on its side when not in use. Some tools with large battery packs will stand upright but

may be easily knocked over.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if drilling operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

3

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 4

ANSI S12.6 (S3.19) hearing protection,

NIOSH/OSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.Some examples of these chemicals are:

lead from lead-basedpaints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treatedlumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury.Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

Recommended Minimum Wire Size for Extension Cords Total Length of Cord

25 ft.

50 ft.

75 ft.

100 ft.

125 ft.

150 ft.

175 ft.

7.6 m

15.2 m

22.9 m

30.5 m

38.1 m

45.7 m

53.3 m

Wire Size AWG

 

 

 

 

 

18

18

16

16

14

14

12

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

4

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 5

The label on your tool may include the following symbols. The symbols and their definitions are as follows:

V..................

volts

A ..................

amperes

Hz................

hertz

W..................

watts

min ..............

minutes

no ................

alternating current

 

 

 

 

 

direct current

no load speed

 

 

 

 

 

 

 

 

 

 

Class I Construction

 

 

 

 

earthing terminal

 

 

 

 

................

 

 

 

..................

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(grounded)

 

 

 

................

safety alert symbol

 

 

 

 

................

Class II Construction

…/min ..........

revolutions or reciprocation

 

 

 

 

 

(double insulated)

 

 

 

 

per minute

FUNCTIONAL

A

Figure

 

1. Trigger Switch

5

2.Forward/Reverse Button

3.Dual Range Gearing

4.Torque Adjust Collar

5.Keyless Chuck

6.Battery Compartment

7.Battery Release Button (on battery)

1

7

6

B

E

5

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 6

F

I

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for battery chargers.

• Before using charger, read all instructions and

markings on charger, battery

pack, and product using battery pack.

 

WARNING: Burn hazard. To reduce the risk

charge only Black & Decker

VPXTM batteries. Other types of batteries may

causing personal injury and damage.

CAUTION: Under certain conditions, with the

plugged in to the power supply,

the charger can be shorted by foreign material

materials of a conductive nature

such as, but not limited to, steel wool, aluminum

or any buildup of metallic particles

should be kept away from charger cavities.

unplug the charger from the power

supply when there is no battery pack in the cavity

charger before attempting to

clean.

 

WARNING: Shock hazard. Do not allow any

to get inside charger.

DO NOT attempt to charge the battery

anything other than a

Black & Decker VPXTM branded charger. Black & Decker VPXTM chargers and

battery packs are specifically designed to

together.

These chargers are not intended for any

other than charging Black &

Decker VPXTM rechargeable batteries.Any

uses may result in risk of fire,

electric shock or electrocution.

 

Do not expose charger to rain or snow.

Pull by plug rather than cord when disconnecting charger or when

disconnecting cords using the daisy chain

. This will reduce risk of

damage to electric plug and cord.

 

Make sure that cord is located so that it

not be stepped on, tripped over,

or otherwise subjected to damage or

 

Do not use an extension cord unless it

necessary. Use of

improper extension cord could result in risk

electric shock, or electrocution.

6

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 7

An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size.

Do not operate charger with damaged cords or plugs — have them replaced immediately.

Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way.

Do not disassemble charger. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

The charger is designed to operate on standard household electrical power (120 Volts). Do not attempt to use it on any other voltage.

See instruction manual for use in countries other than the U.S.A.

This power unit is intended to be correctly orientated in a vertical or floor mount position.

SAVE THESE INSTRUCTIONS INTRODUCTION

Black & Decker VPXTM chargers are designed to charge Black & Decker VPXTM battery packs in approximately5-6hours. The charger requires no adjustment and is designed to be as easy as possible to operate. Simply place your battery pack into the receptacle of a plugged in charger and it will automatically charge the pack. As you add new chargers to your Black & Decker VPXTM system, utilize the “daisy chain” feature to power multiple chargers from a single outlet.

IMPORTANT SAFETY INSTRUCTION FOR BATTERY PACKS

WARNING: For safe operation, read this manual and manuals originally supplied with tool before using the charger.

The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium ion battery packs are burned.

Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes.

If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.

Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

• Charge the battery packs only in Black & Decker VPXTM chargers.

DO NOT splash or immerse in water or other liquids. This may cause premature cell failure.

Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in summer).

7

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 8

WARNING: Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to service center for recycling.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can contact exposed battery terminals.For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.

STORAGE RECOMMENDATIONS

1.Always store batteries charged.

2.The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold.

3.Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished.

CHARGING PROCEDURE

1.Plug the charger into an appropriate outlet before inserting the battery pack.

2.Insert the battery pack into the charger (figure B).Be sure the pack is fully

seated in the charger. While charging, the red (charging) LED will flash continuously (slowly) indicating that the charging process has started.

3.The completion of charge is indicated by the red LED becoming solid. (approximately 5-6hours) The pack is fully charged and may be used at this time or left on the charger.

4.Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished.

CHARGE INDICATORS

Replace Pack:

These chargers are designed to detect certain problems that can arise with battery packs which would be indicated by the red light flashing at a fast rate. If this occurs,re-insertbattery pack. If problem persists, try a different battery pack to determine if the charger is OK. If the new pack charges correctly, then the original pack is defective and should be returned to a service center for recycling. If the new battery pack gives the same trouble indication as the original, have charger tested at an authorized service center.

Note: It may take as long as fifteen minutes for the charger to determine that the pack is defective.

If the battery pack is too hot or too cold, the LED will alternately blink fast and slow, one flash at each speed and repeat.

DAISY CHAIN (FIGURE C)

Single and dual port chargers can be electrically connected in any order up to a maximum of 4 chargers. Each charger has a power-incord (which plugs into the electrical outlet) and apower-outcord (which plugs into the next charger).

To connect chargers in a daisy chain:

1.Plug the power-incord into an electrical outlet.

2.Remove the power-incord from the next charger and plug in thepower-outcord from the charger that is now plugged into the outlet.

3.Repeat this process for the remaining chargers.

Chargers that are daisy chained together operate independently as though each one

8

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 9

was plugged into a sperate outlet therefore a battery can be removed from anywhere along the daisy chain without affecting the other chargers.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left connected indefinitely with the LED illuminated. You may see the LED return to flashing (charging) state, as the charger will occasionally “top off “ the battery charge.

IMPORTANT CHARGING NOTES

1.Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

Note: The charger will not charge a battery pack if the pack temperature is below approximately 32°F (0°C) or above 122°F (50°C). The battery pack should be left in the charger and the charger will begin to charge automatically when the cell temperature warms up or cools down.

2.The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

3.If the battery pack does not charge properly:

a.Check current at receptacle by plugging in a lamp or other appliance

b.Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

c.Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C).

d.If charging problems persist, take the tool, battery pack and charger to your local service center.

4.The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

5.Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

6.Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Do not allow any liquid to get inside charger.

CAUTION: Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling.

TO MAXIMIZE BATTERY LIFE:

1.Remove the batteries from the charger after the charging is completed.

2.Store the batteries at room temperature or below.

3.Recharge discharged batteries within 1 week. Battery life will be greatly diminished if the battery sits too long after being discharged.

SAFETY WARNINGS AND INSTRUCTIONS: DRILLS

1.Hold drill firmly with one hand on the grip and the other hand on the bottom of the tool.

2.When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.

WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly with both hands to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall beforere-starting.

9

90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 10

OPERATING INSTRUCTIONS

WARNING: Always use proper eye protection that conforms to ANSI Z87.1 (CAN/CSA Z94.3) while operating this power tool.

NOTE: Battery pack performance will decrease under heavy use conditions when temperature is below 32° F (0°C). As the battery cells heat up the performance will improve.

INSTALLING AND REMOVING THE BATTERY PACK (FIGURE D, E)

CAUTION: Make certain thelock-offbutton is engaged to prevent switch actuation before removing or installing battery.

Installing the battery pack:

Insert the metal terminal end of the battery pack into the product until you hear the lock snap into place and the VPXTM logo shows through the window as shown infigure D.

CAUTION: The battery can only be inserted in one direction. If the battery does not fit, remove and reverse the orientation. Do not force it.

Removing the battery pack:

Press the release button as shown in figure E and firmly pull the battery pack out of the handle. Insert the battery pack into the charger (figure B) as described in the charger section of this manual.

TRIGGER SWITCH & REVERSING BUTTON (FIGURE F)

The drill is turned ON and OFF by pulling and releasing the trigger switch.

A forward/reverse control button determines the direction of the tool and also serves as a lock off button.

To select forward rotation, release the trigger switch and depress the forward/reverse control button to the left.

To select reverse direction, depress the forward/reverse control button the opposite direction.

The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released.

TORQUE CONTROL (FIGURE G)

This tool is fitted with a 8 position collar to select the operating mode and to set the torque for tightening screws. Large screws and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials.

For drilling in wood, metal and plastics, set the collar to the drilling position symbol .

For screwdriving, set the collar to the desired setting. If you do not yet know the appropriate setting, proceed as follows:

Set the collar to the lowest torque setting.

Tighten the first screw.

If the clutch ratchets before the desired result is achieved, increase the collar setting and continue tightening the screw. Repeat until you reach the correct setting. Use this setting for the remaining screws.

HIGH/LOW SPEED SELECTOR (FIGURE H)

The dual range feature of your drill allows you to shift gears for greater versatility. To select low speed, high torque setting (position 1), turn tool off and permit to stop. Slide gear shifter button to the left.

To select the high speed, low torque setting (position 2), turn tool off and permit to stop. Slide gear shifter button to the right.

NOTE: Do not change gears when tool is running. If you are having trouble changing gears, make sure that the dual range gear button is either completely pushed to the right or left.

KEYLESS CHUCK (FIGURE I)

To insert a drill bit or other accessory:

1.Grasp the chuck and rotate it in the counterclockwise direction, as viewed from the chuck end.

10