Lift-Off®
B A G L E S S
U S E R ’ S G U I D E
3750/6595/6801 SERIES
3 Safety Instructions
4 Product Diagram
4-6 Assembly Instructions
6-9 Operation / Special Tools
10-13 Maintenance
14 Troubleshooting
15 Replacement Parts
15 Consumer Services
16 Warranty
ug603-5540_3750_905.indd 1 |
10/3/05 3:47:49 PM |
Thanks For Buying A BISSELL Lift-Off®
We’re glad you purchased a BISSELL Lift-Off Vacuum. Everything
we know about floor care went into the design and construction of this powerful, high-tech home vacuuming system.
Your BISSELL Lift-Off is well made, and we back it with a limited comprehensive one-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your BISSELL Lift-Off.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
2
ug603-5540_3750_905.indd 2 |
10/3/05 3:47:53 PM |
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be observed, including the following:
READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.
Always connect to a polarized outlet (left slot is wider than right). Unplug from outlet when not in use and before conducting maintenance.
WARNING: To reduce
the risk of fire, electric shock, or injury:
■Do not modify the polarized plug to fit a non-polarized outlet or extension cord.
■Do not leave vacuum cleaner unattended when it is plugged in.
■Unplug from outlet when not in use and before servicing.
■Do not use outdoors or on wet surfaces.
■Do not allow children to operate vacuum cleaner or use as a toy.
■Close attention is necessary when used by or near children.
■Do not use for any purpose other than described in this User’s Guide.
■Use only manufacturer’s recommended attachments.
■Do not use with damaged cord or plug.
■If appliance is not working as it should, has been dropped, damaged, left outdoors,
or dropped into water, have it repaired at an authorized service center.
■Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
■Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
■Do not handle vacuum cleaner or plug with wet hands.
■Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
■Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
■Turn off all controls before plugging or unplugging vacuum cleaner.
■Use extra care when cleaning stairs.
■Unplug before attaching the TurboBrush.
■Do not pick up flammable materials (lighter fluid, gasoline, kerosene, etc.) or use in the presence of explosive liquids or vapors.
■Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
■Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth
proofing substances, flammable dust, or other explosive or toxic vapors.
■Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
■Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
■Do not use without filters in place.
■Use only on dry, indoor surfaces.
■Keep appliance on a level surface.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
THIS APPLIANCE HAS A POLARIZED PLUG.
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.
This model is for household use only.
3
ug603-5540_3750_905.indd 3 |
10/3/05 3:47:53 PM |
Dusting Brush/
Upholstery Tool
Hose Clip
Upper Tank Knob
Crevice Tool 
HEPA Media
Post-Motor Filter
Handle Release
Pedal
Hose Grip Base
Comfort Grip
Cord Clip
Stretch Hose
Quick Release
Cord Wrap
Telescoping
Extension Wand
Power Cord
Hose Grip
Dirt
Container
Pre-Motor
Filter
Headlight
Height
Adjustment
Knob
Powerfoot
|
CAUTION: |
|
Do not plug in your vacuum |
|
cleaner until you are familiar |
|
with all instructions and |
4 |
operating procedures. |
Handle
Release Button
Power Switch
Brush On/Off
Switch
Detachable Canister
Clean Filter
Indicator (Select
Models Only)
Louvers/Filter
Frame
Upper Tank Filter
(Inside Louvers)
Upper Tank
Lock ’n Seal®
Lever
Furniture
Protection
Guard
ug603-5540_3750_905.indd 4 |
10/3/05 3:47:53 PM |
How To Use This Guide
This User’s Guide has been designed to help you get the most satisfaction from your BISSELL Lift-Off. You’ll find assembly and operating instructions,
safety precautions, as well as maintenance and troubleshooting instructions. Please read this Guide thoroughly before assembling your vacuum cleaner.
Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Familiarize yourself with the parts and where they fit. Following this User’s Guide will greatly enhance your ability to get the most performance from your BISSELL Lift-Off for many years.
WARNING:
Plastic film can be dangerous. To avoid danger of suffocation, keep away from babies and children.
How To Put It Together
The only tool you’ll need to assemble your vacuum cleaner is a screwdriver.
Attach Handle To Vacuum
1.Locate the vacuum Handle and remove the screw packet taped to the base of the Handle.
2.Stand the vacuum upright and slide the base of the Handle firmly into the grooves at the top of the vacuum body.
3.Check to be sure the Handle is fitted to the vacuum body. If there is a gap in front, continue to push firmly until the Handle is flush.
4.Insert two of the screws from the screw packet into the existing hole. Tighten securely with a screwdriver.
Attach Vacuum Hose and Tools
1.Position the Hose Assembly on the back of the canister as shown.
2.Attach the Hose to the vacuum.
Standard Models - Use the remaining two screws from the packet. Tighten securely with a screwdriver.
Twist ‘n Snap™ Hose Models - (Select Models)
Position the Twist ‘n Snap Hose assembly on the vacuum and line up the tabs on the base of the hose with the corresponding notches. Turn the Twist ‘n Snap Hose to the right to lock into place.
Standard Models
Twist ‘n Snap Hose Models
5
ug603-5540_3750_905.indd 5 |
10/3/05 3:47:54 PM |
Loading...