PowerForce® Turbo
B A G L E S S
U S E R ’ S G U I D E
6596 SERIES
3 Safety Instructions
4 Product View
5-6 Assembly Instructions
6-7 Operation / Special Tools
8-11 Maintenance
12-13 Troubleshooting
14 Replacement Parts
15 Consumer Services
16 Warranty
ug203-2829_6596_1105.indd 1 |
1/11/06 4:03:29 PM |
Thanks For Buying A BISSELL PowerForce® Turbo Bagless
We’re glad you purchased a BISSELL PowerForce Turbo Bagless Vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home vacuuming system.
Your BISSELL PowerForce Turbo Bagless is well made, and we back it with a limited comprehensive one-year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services Department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your BISSELL PowerForce Turbo Bagless.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
2
ug203-2829_6596_1105.indd 2 |
1/11/06 4:03:33 PM |
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be observed, including the following:
READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.
Always connect to a polarized outlet (left slot is wider than right). Unplug from outlet when not in use and before conducting maintenance.
WARNING: To reduce
the risk of fire, electric shock, or injury:
■Do not modify the polarized plug to fit a non-polarized outlet or extension cord.
■Do not leave vacuum cleaner unattended when it is plugged in.
■Unplug from outlet when not in use and before servicing.
■Do not use outdoors or on wet surfaces.
■Do not allow children to operate vacuum cleaner or use as a toy.
■Close attention is necessary when used by or near children.
■Do not use for any purpose other than described in this User’s Guide.
■Use only manufacturer’s recommended attachments.
■Do not use with damaged cord or plug.
■If appliance is not working as it should, has been dropped, damaged, left outdoors,
or dropped into water, have it repaired at an authorized service center.
■Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
■Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
■Do not handle vacuum cleaner or plug with wet hands.
■Do not put any object into openings.
Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
■Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
■Turn off all controls before plugging or unplugging vacuum cleaner.
■Use extra care when cleaning stairs.
■Unplug before attaching the TurboBrush.
■Do not pick up flammable materials (lighter fluid, gasoline, kerosene, etc.) or use in the presence of explosive liquids or vapors.
■Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
■Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.
■Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
■Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
■Do not use without filters in place.
■Use only on dry, indoor surfaces.
■Keep appliance on a level surface.
■Do not carry the vacuum cleaner while it is running.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
THIS APPLIANCE HAS A POLARIZED PLUG.
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.
This model is for household use only.
3
ug203-2829_6596_1105.indd 3 |
1/11/06 4:03:34 PM |
Cord Clip
Hose Clip |
Handle |
Stretch Hose
TurboBrush®
Bracket
Combination
Dusting Brush/
Upholstery Tool
Power Switch
Handle
Release
Pedal
Foot Hose
Crevice Tool
Carrying
Handle
Extension Wand
Quick Reach®
Handle
Hose Wand
Hose
Wand Base
Dirt Container
Filter Cup
Headlight
Height
Adjustment
Knob
Powerfoot
TurboBrush®
Quick Release
Cord Wrap
Louvers
Power Cord
Upper Tank
Washable Inner and
Outer Circular Filters
Lock ’n Seal™
Lever
HEPA Post-Motor Filter
Furniture Protection
Guard
|
CAUTION: |
|
Do not plug in your vacuum |
|
cleaner until you are familiar |
|
with all instructions and |
4 |
operating procedures. |
ug203-2829_6596_1105.indd 4 |
1/11/06 4:03:34 PM |
How To Use This Guide
This User’s Guide has been designed to help you get the most satisfaction from your BISSELL PowerForce Turbo Bagless. You’ll find assembly and operating instructions, safety precautions, as well as maintenance and troubleshooting instructions. Please read this Guide thoroughly before assembling your vacuum cleaner.
Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Familiarize yourself with the parts and where they fit. Following this User’s Guide will greatly enhance your ability to get the most performance from your BISSELL PowerForce Turbo Bagless for many years.
WARNING:
Plastic film can be dangerous. To avoid danger of suffocation, keep away from babies and children.
How To Put It Together
The only tool you’ll need to assemble your vacuum cleaner is a screwdriver.
Attach Handle To Vacuum
1.Locate the vacuum Handle and remove the screw packet taped to the base of the Handle.
Stand the vacuum upright and place the Handle on the 2. top of the vacuum body as shown.
Insert the screws provided from the screw packet into
3.the existing holes on each side. Tighten securely with a screwdriver.
Attach Vacuum Hose and Tools
1. Attach the Twist ‘n Snap™ Hose by lining up the tabs on the base with the corresponding notches on the back of the vacuum as shown.
2. Turn the Twist ‘n Snap Hose to the right to lock the hose into place.
3. Grasping the Quick Reach Handle, slide the end of the Hose Wand onto the Hose Wand Base. Snap the Hose into the Hose Clip.
NOTE: The Powerfoot will not operate effectively unless the Hose Wand is firmly attached.
4. Slide the Extension Wand and the Crevice Tool together into the storage clip on the side of the vacuum.
5. Snap the Combination Tool into the storage clip on the back of the vacuum.
6. The TurboBrush® Bracket slides onto the front of the Handle. Attach the Bracket by aligning the pegs with the holes on the
Handle as shown and pulling down until it is locked into place.
5
ug203-2829_6596_1105.indd 5 |
1/11/06 4:03:35 PM |