Bissell 1699V User Manual

Size:
1.47 Mb
Download

Operation

Empty the tank

1.Remove the water tank from the base using the tank carry handle. Carry the tank like a bucket to a utility sink or outside where you will dispose of the collection water. Remove the top of the tank by rotating the handle forward to unlatch lid and lifting lid off tank.

2.Empty collection water from bottom of tank.

NOTE: You may notice hair & debris deposits on the carpet or in the tank that were loosened by the cleaning action (especially with newer carpets that have never been deep cleaned before). This debris should be picked up and thrown away.

1.

2.

3.

3.After each use, remove and rinse the lint screen located on the tank lid.

4.Refill the Tank-in-Tankby referencing “Fill the water tank” on page 9. Remember to

secure the top of the tank by rotating the

4.

5.

handle and test to make sure it is secure before picking up.

5. ReturnTank-in-Tankto the machine.

NOTE: Always check the level of cleaning formula in the SmartMix tank at the same time, and refill as needed

Rinse (optional)

Rinsing is an optional step that can be done during the cleaning process by switching to the water rinse setting, or it can be done after the carpeted area has been cleaned.

1. Simply choose the water rinse setting on the

1

SmartMix dial, and follow the same path as you did for cleaning, taking care to do a forward (wet) stroke by depressing the trigger, a backward (wet) stroke, and a forward and backward (dry) stroke, releasing the trigger. Continue this until the water you see coming up the nozzle is clear.

w w w . b i s s e l l . c o m

When filling bottle or storing unit, set

dial to:

WATER

RINSE

8 0 0 . 2 3 7 . 7 6 9 1

11

ug310-5941_7901bi_608.indd11

6/24/08 1:39:03 PM

Maintenance and care

Machine storage

Once your cleaning is complete, make sure the water tank is emptied and rinsed out. Put the unit away in a closet or basement for the next use. The SmartMix tank can remain filled and ready to go (store with machine set to water rinse setting), or it can simply be emptied back into the formula bottle if that is more convenient.

Note: Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is a danger of freezing.

Freezing will damage internal components and void the warranty.

Machine care

For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete.

1.Turn power and heater switches OFF ( 0 ). Unplug the machine and wrap the power cord.

2.After emptying the water tank, rinse it out at a faucet with running hot tap water, taking care to clean underneath the heavy duty bladder, and all around it. Clean out lint trap.

3.Replace the Tank-in-Tankon the machine.

4.Clean out the flow indicator filter each time it is used to ensure best cleaning performance. Unscrew the flow indicator cap, lift out the red rotor and white filter.

Rinse all three parts with water. Replace the filter and rotor. Replace the flow indicator cap. Turn until snug, do not over-tighten.

5.Any loose hair or debris can be pulled from the brush roll if desired and thrown away.

6.Wipe the machine’s exterior with a soft cloth.

7.After carpet is dry, vacuum again to remove hair and fuzz.

Cleaning with attachments

Your ProHeat machine comes equipped with a hose and at least one attachment for cleaning stairs, upholstery, and more.

1.Important! If using to clean upholstery, check upholstery tags for instructions.

WARNING:

To reduce the risk of fire, electric shock or injury, unplug from the outlet before servicing.

Flow Indicator

4.

12 w w w . b i s s e l l . c o m

8 0 0 . 2 3 7 . 7 6 9 1

ug310-5941_7901bi_608.indd12

6/24/08 1:39:03 PM

Maintenance and care

Cleaning with attachments (continued)

A.Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your ProHeat. If the tag is coded with an “X” or an “S” (with a diagonal stripe through it), or says “Dry Clean Only”, do not proceed with any deep cleaning machine.

Do not use on Velvet or Silk. If manufacturer’s tag is missing or not coded, check with your furniture dealer or manufacturer.

B.Check for colorfastness in an inconspicuous place.

C.If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet.

D.Plan activities to allow upholstery time to dry.

E.Vacuum thoroughly to pick up loose debris and pet hair. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds.

2.Follow the instructions on page 9 for filling the water tank and the formula tank.

3.Set ready tools dial to the tools setting. This will allow spray and divert the suction to the hose.

*SmartTemp heats the cleaning solution for carpet and hard floor application only. It does not heat solution sprayed through the accessory tools.

4.Set SmartMix dial to normal.

5.Attach the cleaning tool to the end of the hose.

6.Plug in and turn on the power switch.

7.Clean by pressing the trigger to spray solution onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface.

Release the trigger to suction soiled water. Continue to clean in the area, working in small sections, until no more dirt can be removed. Rinse (optional) and suction as needed.

Caution: Do no overwet.

8.When cleaning is complete, remove and rinse tools in clean, running water.

9.Coil hose around the tool caddy.

Manufacturer’s tag

WARNING:

To reduce the risk of injury, be extra careful when cleaning stairs. Make sure machine is secure and level.

w w w . b i s s e l l . c o m

8 0 0 . 2 3 7 . 7 6 9 1

13

ug310-5941_7901bi_608.indd13

6/24/08 1:39:04 PM

Maintenance and care

Cleaning with attachments (continued)

10.Empty water tank and rinse out, following the instructions on page 11.

11.Return ready tools dial to floor cleaning.

Cleaning fluid section

Keep plenty of genuine BISSELL deep cleaning formulas on hand so you can clean and protect whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas.

WARNING:

To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner. NonBISSELL cleaning solutions may harm the machine and void the warranty.

48 oz. BISSELL

48 oz. BISSELL

48 oz. BISSELL

48 oz. BISSELL

48 oz. BISSELL

43 oz. BISSELL

32 oz.

22 oz.

Fiber Cleansing

MultiAllergen

Pet Odor and Soil

Natural Orange

Lavender Essence

3X Concentrated

BISSELL

BISSELL

Formulawith

Removal

RemovalFormula

Extract Formula

Formula with

Fiber Cleansing

Hard Floor

Tough Stain

Scotchgard

Formulawith

with Scotchgard

with Scotchgard

Scotchgard

Formula with

Solutions

PreCleaner

Protector

Scotchgard

Protector

Protector

Protector

Scotchgard

Formula

#0400

#0710

Protector

#0730

#0740

#0750

Protector

#0484

 

 

#0720

 

 

 

#0716

 

 

Stain removal

Do Not Delay! Attending to an accident soon after it occurs ensures the chances for full removal. Leaving it for an extended period of time may cause it to set and become permanent.

1.Blot up liquids with an absorbent cloth or paper towels. White materials are recommended because certain dyes may bleed and make the stain worse.

2.Gently scrape up any semi-solidswith a spoon or spatula. Do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery.

3.If the area has dried, remove the remaining semi-solidsand residue with a sweeper

or vacuum.

14 w w w . b i s s e l l . c o m

8 0 0 . 2 3 7 . 7 6 9 1

ug310-5941_7901bi_608.indd14

6/24/08 1:39:05 PM

Maintenance and care

Stain removal (Continued)

4.Be sure to test any spot removal formulas in an inconspicuous area first. This is important as some dyes and materials could be damaged or discolored by cleaning solvents. If such a change should occur, try a different solution or call a professional.

5.If cleaning on Berber carpeting, gently run your machine over a hidden area. If no fuzzing occurs, continue cleaning in soiled area.

6.Using the BISSELL Tough Stain PreCleaner, spray evenly over soiled area. Do not overwet. Wait 3-5minutes. Gently work the solution by blotting area with a clean, damp, color safe cloth.

7.Clean using either the floor cleaning or tools setting on the ReadyTools dial.

Hard floor cleaning

Your ProHeat model may have come with a hard floor attachment and Hard Floor Solutions formula. If not, these products are available for purchase by contacting the BISSELL Consumer

Services department by phone or on the website. The hard floor tool provides effective cleaning for linoleum, vinyl, and tile floors.

Caution: Do not use on unsealed hardwood floors.

1.Vacuum or sweep thoroughly to pick up any loose debris and pet hair.

2.Move any furniture, if needed.

3.Empty any carpet cleaning formula back into the BISSELL bottle if stored in the formula tank. Fill formula tank with BISSELL Hard Floor Solutions, available at many retailers, or contact BISSELL Consumer Services.

w w w . b i s s e l l . c o m

8 0 0 . 2 3 7 . 7 6 9 1

15

ug310-5941_7901bi_608.indd15

6/24/08 1:39:06 PM

Maintenance and care

Hard floor cleaning (Continued)

4.Fill the water tank with hot tap water and set aside.

5.Attach the hard floor tool onto the floor

nozzle with the long tab to the right side of the floor nozzle. First attach left side (short tab) catching tab over nozzle edge. Gently bend long tab (right side) outward to easily snap over edge of clear nozzle on left.

6.Set the ready tools dial to floor cleaning.

7.Set the SmartMix dial to normal clean.

8.Plug into an outlet and turn the power switch and heater ON ( I ).

9.Slowly move the machine forward and back over bare floor surface one time while pressing trigger. Caution: Do not overwet.

10.Repeat the motion without pressing the trigger. This allows the bare floor tool to squeegee and suction up the dirty water.

11.Allow approximately 30 minutes for floors to dry.

12.Remove hard floor tool and rinse and dry before storing.

13.If any formula remains in the formula tank, pour it back into the Hard Floor Solutions bottle for use the next time.

14.Rinse out the formula tank.

Troubleshooting

SmartTemp ready light does not illuminate.

Possible Causes

1.The SmartTemp switch is not turned ON ( I ).

2.The machine power switch is not to turned ON ( I ).

16 w w w . b i s s e l l . c o m

Bottom Front Edge

of Floor Nozzle

Hard Floor

Snap Together

Cleaning Tool

WARNING:

To reduce the risk of fire, electric shock or injury unplug from outlet before servicing.

Remedies

1.Turn ON ( I ) the SmartTemp switch.

2.Both switches must be ON ( I ) to activate the SmartTemp ready light.

8 0 0 . 2 3 7 . 7 6 9 1

ug310-5941_7901bi_608.indd16

6/24/08 1:39:06 PM

Troubleshooting

Reduced spray or no spray.

Possible Cause

1.Bladder may be empty.

2.SmartMix tank may be empty.

3.The filter may be clogged.

4.Tanks may not be seated properly.

5.Pump may have lost prime.

6.The Pump belt may be broken.

DirtLifter PowerBrush does not turn.

Possible Cause

1.The brush belt or pump belt is off or broken.

Lift Here

Insert

Screwdriver

Blade Here

w w w . b i s s e l l . c o m

Remedies

1.Refill bladder with hot tap water.

2.Fill with BISSELL deep Cleaning formula for cleaning. Fill with water if rinsing.

3.Clean out flow indicator filter, page 12.

4.Turn power OFF (O); remove & reseat tanks.

5.Turn power OFF (O); after 1 minute turn ON and press trigger.

6.Turn on the machine and check to see that the DirtLifter PowerBrush turns. If it does not, refer to #1 below.

Remedies

1.Turn the machine OFF (O) and unplug from the outlet. To check if the brush belt or pump belt has broken, you will need a flat head screwdriver. Insert the blade end into the lower slot of the belt access door to release the lower snap. If necessary, insert the blade end into the upper slot to release the upper snap. Examine the belt for breakage. If broken, please refer to Replacement Parts on page 19 before calling Consumer Services. Complete installation instructions will accompany the replacement belt.

8 0 0 . 2 3 7 . 7 6 9 1

17

ug310-5941_7901bi_608.indd17

6/24/08 1:39:07 PM

Troubleshooting

Cleaner not picking up solution.

Possible Causes

1.ReadyTools dial may be on the wrong setting for the cleaning job.

2.Nozzle window may not be properly attached.

Remedies

1.Set ReadyTools dial to either floor cleaning or tools.

2.Press down firmly on the black oval gasket at the top window to make sure the two tabs on the back of the nozzle window are snapped into the mating slots in the main housing.

3.Tank-in-tanklid is not properly installed.

4.Tank-in-tankis not properly seated.

5.Poor tool position.

(Hand held attachments only).

6.Tank-in-tankhas picked up maximum dirty water.

3.Re-installlid; refer to page 9.

4.Tank-in-tankmust be firmly seated to function; remove and reseattank-in-tank.

5.Adjust angle; apply more downward pressure.

6.Empty tank-in-tank,refer to page 11.

Other Maintenance or Service not included above should be performed by an

authorized service representative.

Thank you for selecting a BISSELL product.

If you should happen to need assistance during assembly or operations, call 1-800-237-7691

Please do not return this product to the store

BISSELL Consumer Services

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Services 1-800-237-7691

Monday - Friday

8 a.m. — 10 p.m. ET

Saturday

9 a.m. — 8 p.m. ET

Or write:

BISSELL HOMECARE, INC

PO Box 3606

Grand Rapids MI 49501

ATTN: Consumer Services

Or visit the BISSELL website - www.bissell.com

When contacting BISSELL, have model number of unit available.

Please record your Model Number: ___________________

Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim. See "About Your Warranty" on page 20 for details.

18 w w w . b i s s e l l . c o m

8 0 0 . 2 3 7 . 7 6 9 1

ug310-5941_7901bi_608.indd18

6/24/08 1:39:07 PM

Replacement parts - BISSELL ProHeat

Below a list of common replacement parts*. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired.

 

Item

Part No.

 

Part Name

 

 

 

1

210-9201

 

4” Small Area Tool

 

 

 

2

203-6655

 

Spraying Crevice Tool

 

 

 

3

203-6652

 

TurboBrush®

 

 

 

4

214-9131

 

Bare Floor Tool

 

 

 

5

214-9142

 

PreTreat Wand

 

 

 

6

215-9155

 

Tough Stain Brush

 

 

 

7

015-9043

 

Tank Assembly Complete (Includes lid assembly)

 

8

015-4439

 

Tank Lid Assembly

 

 

 

9

015-9041

 

Tank Bottom

 

 

 

10

210-1785

 

SmartMix® Tank (Includes Cap)

 

 

11

210-1795

 

SmartMix® Cap Assembly

 

 

 

12

555-6503

 

Flow Indicator Cap Assembly

 

 

13

214-9871

 

Floor Nozzle Window and Gasket

 

 

14

210-4052

 

Window Gasket

 

 

 

15

215-0628

 

Replacement Pump Belt (With Instructions)

 

 

16

015-0621

 

Replacement Belt Brush (With Instructions)

 

 

17

213-3501

 

Lint Screen

 

 

 

18

0710

 

Fiber Cleansing Formula48 oz

 

 

19

0720

 

Multi-AllergenRemovalFormula 48 oz

 

 

20

0730

 

Pet Odor and Soil RemovalFormula 48 oz

 

 

21

0716

 

3x Concentrated Fiber Cleansing Formula with

 

 

 

 

Scotchgard™ Protector 43 oz.

 

 

22

0484

 

Hard Floor Solutions32 oz

 

 

 

23

0400

 

tough Stain PreCleaner22 oz

 

 

*Not all parts are included with every model.

 

 

1

2

3

4

5

6

7

8

9

10

12

13

15

16

 

 

 

 

14

 

 

 

 

11

 

 

 

 

17

18

19

20

21

22

23

w w w . b i s s e l l . c o m

8 0 0 . 2 3 7 . 7 6 9 1

19

ug310-5941_7901bi_608.indd19

6/24/08 1:39:11 PM

Warranty - BISSELL ProHeat

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover,

please contact BISSELL Consumer Services by E-mail,telephone, or regular mail as described below.

Limited One Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for one years any defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is

not covered.

If your BISSELL product should require service:

Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.

If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Services.

Website or E-mail:www.bissell.com

Use the “Customer Service” tab.

Or Call:

BISSELL Consumer Services 1-800-237-7691

Monday - Friday 8 a.m. - 10 p.m. ET Saturday 9 a.m. - 8 p.m. ET

Or write:

BISSELL Homecare, Inc. PO Box 3606

Grand Rapids MI 49501

ATTN: Consumer Services

BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY

OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR

DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Scotchgard is a trademark of 3M.

©2008 BISSELL Homecare, Inc Grand Rapids, Michigan

All rights reserved. Printed in China Part Number 310-5941

Rev 6/08

Visit our website at: www.bissell.com

20 w w w . b i s s e l l . c o m

8 0 0 . 2 3 7 . 7 6 9 1

ug310-5941_7901bi_608.indd20

6/24/08 1:39:11 PM