Billy Goat KD Vacuum KD511H User Manual

Size:
411.25 Kb
Download

2 OPTIONAL ACCESSORIES

1

SHREDDER KIT P/N 890209.

Shreds leaves, reducing total volume.

HEAVY DUTY VACUUM HOSE KIT

P/N 900998. 4"(102mm)x 7'(2.13m)

For vacuuming in hard to reach areas.

NOZZLE WEAR PLATES P/N 890413.

(STD. ON KD511HS)

Extends nozzle life when used along curbs and hard surfaces.

OPTIONAL DEBRIS BAGS

STANDARD TURF PRO DEBRIS BAG

P/N 890028.

For use in leaves and grass in non-dustyconditions.

DEBRIS BAG COVER P/N 900801

Directs dust downward away from operator.

ZIPPERLESS QUICK BAG P/N 890309

For non dusty conditions that are damaging to zippers.

T h a n k Yo u f o r S e l e c t i n g

The Powerful KD VACUUM

CASTER KIT

P/N 890412

For use on hard surface

3

Operator Owner's Manual

KD511IC, KD511H, KD511HS, KD611

Specifications

 

 

KD511IC

KD511H

KD511HS

KD611

 

 

 

 

 

 

ENGINE: H.P.

 

5.0 (3.73 kW )

5.5 (4.11 kW )

5.5 (4.10 kW )

6.0 (4.48 kW )

ENGINE: TYPE

 

B&S I/C

HONDA OHV

HONDA OHV

B&S INTEK I/C

ENGINE: FUEL CAP

1.5qt. (1.4 L)

2.01qt. (1.9 L)

2.01qt. (1.9 L)

1.6qt.

(1.5 L)

ENGINE: OIL CAP

0.63qt. (0.6 L)

0.69qt. (0.65 L)

0.69qt. (0.65 L)

0.69qt.

(0.65 L)

W EIGHT: UNIT

 

103# (46.7 kg)

112# (50.8 kg)

122# (55.3 kg)

145# (65.8 kg)

W EIGHT: SHIPPING

126# (57.2 kg)

135# (61.2 kg)

145# (65.8 kg)

168# (76.2 kg)

W EIGHT: ENGINE

24.38# (11.05 kg)

36# (16.3 kg)

36# (16.3 kg)

28# (12.7 kg)

UNIT SIZE:

OVERALL LENGTH: 62"(1.57m) OVERALL WIDTH

26.75" (0.68m) OVERALL HEIGHT 42" (1.07m)

Part No. 890033

Page 1 of 8

Form No. F0f022502C

5 IN THE INTEREST OF SAFETY

BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL & ENGINE MANUAL.”

THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.

WARNING: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

WARNING: DO NOT

1.DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an odorless and deadly poison.

2.DO NOT place hands or feet near moving or rotating parts.

3.DO NOT store, spill or use gasoline near an open flame, or devices such as a stove, furnace, or water heater which use a pilot light or devices which can create a spark.

4.DO NOT refuel indoors where area is not well ventilated. Outdoor refueling is recommended.

5.DO NOT fill fuel tank while engine is running. Allow engine to cool for 2 minutes before refueling. Store fuel in approved safety containers.

6.DO NOT remove fuel tank cap while engine is running.

7.DO NOT operate engine when smell of gasoline is present or other explosive conditions exist.

8.DO NOT operate engine if gasoline is spilled. Move machine away from the spill and avoid creating any ignition until the gasoline has evaporated.

9.DO NOT transport unit with fuel in tank.

10.DO NOT smoke when filling fuel tank.

11.DO NOT choke carburetor to stop engine. Whenever possible, gradually reduce engine speed before stopping.

13.DO NOT tamper with governor springs, governor links or other parts which may change the governed engine speed.

14.DO NOT tamper with the engine speed selected by the engine manufacturer.

15.DO NOT check for spark with spark plug or spark plug wire removed. Use an approved tester.

16.DO NOT crank engine with spark plug removed. If engine is flooded, place throttle in “FAST” position and crank until engine starts.

17.DO NOT strike flywheel with a hard object or metal tool as this may cause flywheel to shatter in operation. Use proper tools to service engine.

18.DO NOT operate engine without a muffler. Inspect periodically and replace, if necessary. If engine is equipped with muffler deflector, inspect periodically and replace, if necessary, with correct deflector.

19.DO NOT operate engine with an accumulation of grass, leaves, dirt or other combustible material in the muffler area.

20.DO NOT use this engine on any forest covered, brush covered, or grass covered unimproved land unless a spark arrester is installed on the muffler. The arrester must be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands.

21.DO NOT touch hot muffler, cylinder, or fins because contact may cause burns.

22.DO NOT run engine without air cleaner or air cleaner cover.

23.DO NOT operate during excessive vibration!

24.DO NOT leave machine unattended while in operation.

25.DO NOT park machine on a steep grade or slope.

WARNING: DO

1.ALWAYS DO remove the wire from the spark plug when servicing the engine or equipment TO PREVENT ACCIDENTAL STARTING.

2.DO keep cylinder fins and governor parts free of grass and other debris which can affect engine speed.

3.DO pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury.

4.DO examine muffler periodically to be sure it is functioning effectively. A worn or leaking muffler should be repaired or replaced as necessary.

5.DO use fresh gasoline. Stale fuel can gum carburetor and cause leakage.

6.DO check fuel lines and fittings frequently for cracks or leaks. Replace if necessary

7.Follow engine manufacturer operating and maintenance instructions.

8.Inspect machine and work area before starting unit.

12. DO NOT run engine at excessive speeds. This may result in injury & /or damage to unit.

6

 

TABLE OF CONTENTS

 

 

SAFETY INSTRUCTIONS

2

 

 

GENERAL SAFETY

3

 

 

ASSEMBLY

3

 

 

PARTS BAG & CONTROLS

4

 

 

LABELS

4

 

 

OPERATION

5 - 7

 

MAINTENANCE

8 - 9

 

PARTS DRAWING & LIST

10 - 12

 

TROUBLESHOOTING

12

 

 

WARRANTY PROCEDURE

 

 

Part No. 890033

7

SOUND

Sound tests conducted were in accordance with 2000/14/EEC and were performed on 2/21/2002 under the conditions listed:

NOTE: Sound power level listed is the highest value for any model in this manual. Please refer to serial plate on the unit for the sound power level for your model.

Sound level of 96 dBA at operator position

 

GENERAL CONDITION:

 

Sunny

 

TEMPERATURE:

45° F (7.2° C)

111 dB

WIND SPEED:

5 MPH (8.1 kmh)

WIND DIRECTION:

South West

(KD511H MODEL)

HUMIDITY:

60 %

 

BAROMETRIC PRESSURE:

30.18" Hg (767mm Hg)

OPERATOR

Page 2 of 8

 

8 VIBRATION

VIBRATION LEVELS 1.5g

Vibration levels at the operators handles were measured in the vertical, lateral, and longitudinal directions using calibrated vibration test equipment. Tests were performed on 05/19/95 under the conditions listed:

GENERAL CONDITION:

Sunny

TEMPERATURE:

62° F (16.7° C)

WIND SPEED:

5 MPH (8.0 kmh)

WIND DIRECTION:

South

HUMIDITY:

67 %

BAROMETRIC PRESSURE:

30.06" Hg (764mm Hg)

Form No. F022502C

GENERAL SAFETY

For your safety and the safety of others, these directions should be followed:

Use of Ear Protection is recommended while operating this machine.

Use of Eye and Breathing protection is recommended when using this machine, especially in dry

and dusty conditions. Optional bag cover directs dust toward ground, away from the operator.

·DO NOT place hands or feet inside nozzle intake opening, near debris outlet or near any moving parts.

·DO NOT start engine without debris bag and quick disconnect connected firmly in place to exhaust outlet.

·DO NOT start or operate machine with debris bag zipper open.

ASSEMBLY

Read all safety and operating instructions before assembling or starting this unit.

PUT OIL IN ENGINE BEFORE STARTING

NOTswDmbckabridhusi20%f,·c,htobiwmi,t.uihncsd,.x,daive01exovlmpq.tllthet

9 mnuchseaigitdoedigauD'wlptmeoratisnywiot.rfibvalggrfiuldfp.zclyxkft.nofed

ryDuowEOpLrMBt6),hdEctlnFtSgfNf12(ULtu7.id1(l&pib3rflk)wie2hnl0qflyrs,73ilgub8(ivwh,l)ri.k emlasGyspbckhexoailrudhlYumBilpftsHTbim64Con,tENug.ap,einsbud34mA.hgtTnlpCsit.152c(ap.)rtxaust

1qs1gn.i,t AsyDeu2r9ate03t98LiK

ck671MdlontshConectiQuDiP

PggsonHCheckaNTEKI/dt.0atinIrSt&oBr6H.

PACKING CHECKLIST

QUICK DISCONNECT

These items should be included in your carton. If any

of these parts are missing, contact your dealer.

 

Check

Debris Bag

Check

Fig. 2

Engine

Manual Per

Model

Part No. 890033

Page 3 of 8

Form No. F0f022502C

83162Chec

 

g

WARNING

EXPLOSIVE FUEL

400268

 

STOP ENGINE AND ALLOW TO COOL BEFORE REFUELING.

890254

DANGER

810736

STOP

SLOW

FAST

2 da4er

89

 

AT

 

U

P

E

 

D

 

IN U.S.A. USE UNLEADED GASOLINE ONLY

IMPORTANT ENGINE INFORMATION

BRIGGS & STRATTON

CORPORATION FAMILY

VBS190U1G1RB:EM

DISPLACEMENT 190cc. MODEL 12VOHV

16 OPERATION

INTENDED USE: This machine is designed for vacuuming leaves, grass clippings and other types of organic litter and for chipping brush, limbs, corn and sunflower stalks and palm fronds.

Debris mixed with cans, bottles and small amounts of sand can be vacuumed; however, it is not this machine's primary purpose. Vacuuming cans, bottles and sand will affect the longevity of your machine.

Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects. Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 12).

Like all mechanical tools, reasonable care must be used when operating machine.

Inspect machine work area and machine before operating. Make sure that all operators of this equipment are trained in general machine use and safety.

PUT OIL IN ENGINE BEFORE STARTING.

16.1STARTING

ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used.

Engine must be level when checking and filling oil and gasoline.

ENGINE SPEED: Controlled by throttle lever on the handle. Under normal conditions, operate at minimum throttle to accomplish your current cleaning task.

FUEL VALVE: Move fuel valve to "ON" position (when provided on engine).

CHOKE: Operated with throttle control (Honda only).

16.4DEBRIS BAG

Debris bags are normal replaceable wear items.

Note: Frequently empty debris to prevent bag overloading with more weight than you can lift.

An optional bag and dust cover is available for use where debris will be vacuumed in dusty conditions (see Optional Accessories shown on page 1).

DO NOT place bag on or near hot surface, such as engine. Run engine at 1/2 throttle for first 1/2 hour to condition new bag. Your new bag requires a break-in period to condition the pores of the material against premature blockage. The entire bag surface serves as a filter, and must be able to breath to have good vacuum performance.

Be sure engine has come to a complete stop before removing or emptying bag.

This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings page 2-3).

However, many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas. Dust is the greatest cause of lost vacuum performance. However, following these rules will help maintain your machine's ability to vacuum in dusty conditions:

Run machine at idle to quarter throttle.

The debris bag must be cleaned more frequently. A vacuum with a clean, pillow soft bag will have good pickup performance. One with a dirty, tight bag will have poor pickup performance. If dirty, empty debris and vigorously shake bag free of dust.

Pressure-washdebris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before use.

Having one or more spare debris bags is a good way to reduce down time while dirty bags are being cleaned.

DO NOT leave debris in bag while in storage.

PRIMER: Push primer per engine instructions ( B&S only).

THROTTLE: Move remote throttle control to fast position. Pull starting rope to start engine.

IF YOUR UNIT FAILS TO START:

See Troubleshooting on page 12.

16.2VACUUMING OPERATION

VACUUM NOZZLE HEIGHT ADJUSTMENT: is raised and lowered by pulling slightly upward on handle and pulling height adjust rod (item 23) up at left rear of machine.

FOR MAXIMUM PICKUP: Adjust nozzle close to debris, but without blocking airflow into the nozzle.NOTE: Never bury nozzle into debris.

CLEARING A CLOGGED NOZZLE

& EXHAUST: Turn engine off and wait for impeller to stop completely and disconnect spark plug wire. Wearing durable gloves, remove clog.Danger, the clog may contain sharp materials. Reconnect spark plug wire.

16.3HANDLING & TRANSPORTING:

Using two people to lift machine is recommended. Lift holding the handle and front of nozzle. Secure in place during transport.

Part No. 890033

Page 5 of 8

16.5STORAGE

Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.

If engine is to be unused for 30 days or more, prepare as follows:

Be sure engine is cool. Do not smoke. Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Run engine until fuel tank is empty and engine runs out of gasoline.

NOTE: Fuel stabilizer (such asSta-Bil)is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 min.

after adding stabilizer to allow it to reach the carburetor.

Do not store with debris in bag.

16.6COMPOST

Vacuumed leaves, grass and other organic material from your own yard can be emptied into a pile or composter to provide enriched soil for later use as fertilizer in gardens and flower beds (see fig. 3).

NOTE: Allow green chips to dry before spreading around living plants.

Form No. F0f022502C

17 PARTS DRAWING

KD511H, KD511HS, KD511IC, KD611

Part No. 890033

Page 6 of 8

Form No. F022502C

18

* Denotes standard hardware item that may be purchased locally.

ITEM

DESCRIPTION

KD511IC

QTY

KD511H

QTY

KD511HS

QTY

KD611

QTY

 

NO.

 

Part No.

 

 

 

Part No.

 

Part No.

 

Part No.

 

 

1

PRO DEBRIS BAG (service)

890023

1

 

 

890023

1

890023

1

890023

1

 

2

THROTTLE

850270

1

 

 

850270

1

850270

1

850270

1

 

3

 

 

 

 

 

 

 

 

 

 

 

 

4

NUT LOCK (1/4 - 20 )

*8160001

6

 

*8160001

6

*8160001

6

*8160001

6

 

5

SCREW CAP ( 1/4 - 20 x 1-1/2HEX )

*8041008

4

 

*8041008

4

*8041008

4

*8041008

4

 

6

HANDLE ASS’Y (incl. items 4(5),5(5),11(2),75(2),76)

900054

1

 

 

900054

1

900054

1

900054

1

 

7

AXLE HEIGHT ADJUST

890389

1

 

 

890389

1

890389

1

890389

1

 

8

SCREW HANDLE 5/16 - 18 x 1 - 1/2

*8041030

2

 

*8041030

2

*8041030

2

*8041030

2

 

9

CLAMP CABLE

900407

2

 

 

900407

2

900407

2

900407

2

 

10

SCREW CAP 1/4 - 20 x 1 3/4

*8041009

1

 

*8041009

1

*8041009

1

*8041009

1

 

11

BAR BAG SUPPORT

900039

2

 

 

900039

2

900039

2

900039

2

 

12

DOOR EXHAUST ASS’Y (incl. item 62 )

890148

1

 

 

890148

1

890148

1

890148

1

 

13

PLATE TOP ASS’Y (incl. items 14, 15, 29, 48, 57)

890402

1

 

 

890402

1

890402

1

890402

1

 

14

BOLT-CARRIAGE1/4x3/4

*8024021

2

 

*8024021

2

*8024021

2

*8024021

2

 

15

 

 

 

 

 

 

 

 

 

 

 

 

16

WASHER 1/4 FC ZP

*8171002

2

 

*8171002

2

*8171002

2

*8171002

2

 

17

 

 

 

 

 

 

 

 

 

 

 

 

18

BRACKET - HEIGHT ADJUSTMENT

890021

1

 

 

890021

1

890021

1

890021

1

 

19

PLATE UPPER HEIGHT ADJUST

890005

1

 

 

890005

1

890005

1

890005

1

 

20

SPRING

900136

1

 

 

900136

1

900136

1

900136

1

 

21

TIRE - ONLY (PER ASSY)

900507

1

 

 

900507

1

900507

1

900507

1

 

22

PIN - HAIR COTTER

900471

1

 

 

900471

1

900471

1

900471

1

 

23

CABLE HEIGHT ADJUSTMENT

890019

1

 

 

890019

1

890019

1

890019

1

 

24

BOLT - CARRIAGE 5/16 - 18 x 4 1/2

*8024054

4

 

*8024054

4

*8024054

4

*8024054

4

 

25

 

 

 

 

 

 

 

 

 

 

 

 

26

NUT LOCK 5/16 - 18 HEX

*8160002

4

 

*8160002

4

*8160002

6

*8160002

4

 

27

HANDLE LOWER KD510

890346

1

 

 

890346

1

890346

1

890346

1

 

28

PLATE HANDLE SUPPORT

900933

1

 

 

900933

1

900933

2

900933

1

 

29

LABEL DANGER CUT FINGER

400424

2

 

 

400424

2

400424

2

400424

2

 

30

WASHER FLAT CUT 5/16

*8171003

2

 

*8171003

2

*8171003

2

*8171003

2

 

31

 

 

 

 

 

 

 

 

 

 

 

 

32

NUT LOCK 5/16 - 18 THIN HT.

*8161041

2

 

*8161041

2

*8161041

4

*8161041

2

 

33

GRIP HANDLE

400570

2

 

 

400570

2

400570

2

400570

2

 

34

WHEEL ASS’Y (incl. items 21)

900509

4

 

 

900509

4

900509

4

900509

4

 

35

WASHER 0.75 “C”

900997

0 -1

900997

0 -1900997

0 -1900997

0 -

1

36

 

 

 

 

 

 

 

 

 

 

 

 

37

SCREW SM 1/4x3/4 TYPE A

-

-

 

 

-

-

*8122082

4

-

-

 

38

PLATE SKID (incl. items 54)

-

-

 

 

-

-

890413

1

-

-

 

39

 

 

 

 

 

 

 

 

 

 

 

 

40

SCREW CAP 1/4 - 20 x 1 - 1/4

*8041007

4

*8041007

4

*8041007

4

*8041007

4

 

41

 

 

 

 

 

 

 

 

 

 

 

 

42

SCREW SELF TAPPING 10 - 24 x 1/2

*8123086

1

*8123086

1

*8123086

1

*8123086

1

 

43

NOZZLE MAINFRAME ASS’Y (incl. one of items 29,44,42)

890391

1

 

 

890391

1

890391

1

890391

1

 

44

PLUG

900146

1

 

 

900146

1

900146

1

900146

1

 

45

 

 

 

 

 

 

 

 

 

 

 

 

46

 

 

 

 

 

 

 

 

 

 

 

 

47

IMPELLER ASS’Y (incl. items 46, 59 )

900215

1

 

 

900003

1

900003

1

900215

1

 

48

SCREW CAP 1/4-20X 2

8041010

1

 

 

8041010

1

8041010

1

8041010

1

 

49

KEY

900162

2

 

 

900162

2

900162

2

900162

2

 

50

WASHER LOCK 3/8 TWISTED TOOTH

400502

1

 

 

400502

1

400502

1

400502

1

 

51

SCREW CAP 3/8 -24x 1 (HARDENED)(TORQ.50FT-LBS)(68N.m)

900154

1

 

 

900154

1

900154

1

900154

1

 

52

HOUSING ASS’Y (incl. items 12, 14, 15, 16, 66)

890371-S

1

 

890371-S

1 890417-S

1

890371-S

1

 

53

ENGINE HONDA 5.5 H.P. GXV160 KN12

-

-

 

 

900615

1

900615

1

-

-

 

 

ENGINE BRIGGS & STRATTON 5 H.P. QUANTUM IC

890403

1

 

 

-

-

-

-

 

 

 

 

ENGINE BRIGGS & STRATTON 6.0 HP INTEK EDGE

 

 

 

 

 

 

 

 

890387

1

 

54

BOLT CARRIAGE 5/16-18x3/4"

-

-

 

 

-

-

8024039

2

-

-

 

55

LINE PVC

-

-

 

 

-

-

900732

1

-

-

 

56

SCREW CAP 3/8 - 1-1/2TAPTITE

890408

3

 

 

-

-

-

-

890408

3

 

 

SCREW CAP 5/16 - 24 x 1"

-

-

 

 

400164

3

400164

3

-

-

 

57

SCREW CAP 1/4 - 20 x 1/2 HWH

890359

15

 

890359

15

890359

15

890359

15

 

58

WASHER FLAT 1/2 SAE

*8172011

4

*8172011

4

*8172011

4

*8172011

4

 

59

SCREW SOCKET HD. 5/16 - 18 x 3/4 GR. 8

 

 

 

 

 

 

 

 

 

 

 

60

HGT ADJUST ASSY (INCL. ITEMS 18, 20, 22, 23)

890013

1

 

 

890013

1

890013

1

890013

1

 

61

1/2-13CAP NUT NP W/PATCH

890530

4

 

 

890530

4

890530

4

890530

4

 

62

LABEL DANGER FLYING MATERIAL

810736

1

 

 

810736

1

810736

1

810736

1

 

63

LABEL DO NOT FILL WHEN ENGINE IS HOT

400268

1

 

 

400268

1

400268

1

400268

1

 

64

CONNECTOR BAG QUICK

890176

1

 

 

890176

1

890176

1

890176

1

 

65

LABEL READ OWNER'S MANUAL

890301

 

1

 

890301

1

890301

1

890301

1

 

66

LABEL EAR/EYE BREATHING

890254

1

 

 

890254

1

890254

1

890254

1

 

Part No. 890033

Page 7 of 8

Form No. F0f022502C

19 MAINTENANCEcontinued

Use only a qualified mechanic for any adjustments, disassembly or any kind of repair .

WARNING: TO AVOID PERSONAL INJURY, ALWAYS TURN MACHINE OFF, MAKE SURE ALL MOVING PARTS COME TO A COMPLETE STOP.

22.1

21

DISCONNECT SPARK PLUG WIRE

BEFORE SERVICING UNIT.

RECONNECT SPARK PLUG WIRE,

GUARDS, BAG, CAPS AND / OR

HOSE BEFORE STARTING ENGINE.

 

 

Engine Service and Warranty

 

 

 

 

22

WARRANTY PROCEDURE

Contact your nearest engine manufacturer's authorized

Please fill in the WARRANTY CARD and send the upper part to Billy Goat.

 

 

 

 

 

 

servicing dealer.

 

 

 

 

 

The WARRANTY terms are stated on the lower part which remains with the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

user. Whenever a Billy Goat Machine is faulty due to a defect in material

Serial Plate

Record your machine model, serial number and

 

and / or workmanship, the owner should make a warranty claim as follows:

date-of-purchaseand where purchased

 

 

 

 

 

The Machine should be taken to the dealer from whom it was

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1803 S.W. Jefferson

 

 

 

 

 

purchased or to an authorized Billy Goat dealer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

St.

 

 

 

 

 

The owner should present the remaining half of the Warranty

 

 

 

 

 

 

 

 

Lee's Summit, MO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Registration Card, or, if this is not available, the invoice or receipt.

 

 

 

 

 

 

 

 

64082-2312 /USA

 

 

 

 

 

 

 

 

 

 

 

 

 

Tel (816) 524-9666

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fax (816) 524-6983

 

 

 

 

 

The Warranty Claim will be filled in by the authorized Billy Goat Dealer,

 

 

Model

 

 

 

 

Serial No.

 

 

 

 

 

who will send it with the faulty part to Billy Goat headquarters.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The Quality / Service department at Billy Goat headquarters will study

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the claim and parts and will notify their conclusions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The decision by the Quality / Service department at Billy Goat

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unit(Weight)

 

 

 

 

Engine Power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

headquarters to approve or reject a Warranty claim is final and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

lbs.

 

 

kg

 

 

 

kW

 

 

rpm

 

 

binding.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

min-1

 

 

Note: To process a Warranty Claim, it is necessary to quote the Model

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

& Serial number who are printed on the Billy Goat Serial Plate.

 

Purchase

Purchased

Date

from

BILLY GOAT INDUSTRIES INC.

1803 S.W. JEFFERSON STREET LEE'S SUMMIT, MO 64082-2312 /USA PHONE:816-524-9666FAX:816-524-6983www.billygoat.com

Part No. 890033

Page 8 of 8

Form No. F022502C