Billy Goat KD VACUUM KD 410 User Manual

Size:
354.87 Kb
Download

2 OPTIONAL ACCESSORIES

1

ON-BOARDVACUUMHOSE KIT

P/N 900998.

4"(102mm)x 7'(2.13m) w/wear

strip

For vacuuming in hard to reach areas.

NOZZLE WEAR PLATE P/N 890413.

Extends nozzle life when used along curbs and hard surfaces.

OPTIONAL DEBRIS BAGS

PRO FELT DEBRIS BAG

P/N 890023.

For use in dusty conditions.

PRO TURF AND WET WEATHER BAG

P/N 890028

For use in leaves and grass and non dusty conditions.

DEBRIS BAG COVER

P/N 900801 Directs dust downward away from operator.

ZIPPERLESS QUICK BAG P/N 890309 For non dusty conditions that are damaging to zippers.

CASTER KIT

P/N 890412 For use on hard surface

R

T h a n k Y o u f o r S e l e c t i n g

The Powerful KD VACUUM

Operator Owner's Manual

KD 410

3

Specifications

 

 

 

 

 

KD 410

 

 

 

 

ENGINE:H.P.

4.0 (2.98kW )

 

ENGINE:TYPE

B&S

 

ENGINE:FUEL CAP.

1.0qt. (0.95L)

 

ENGINE:OIL CAP.

0.63qt. (0.6L)

 

W EIGHT:UNIT

103# (46.7 kg)

 

W EIGHT:SHIPPING

126# (57.2 kg)

 

ENGINE W EIGHT:

24.8# (11.05 kg)

UNIT SIZE:

OVERALL LENGTH: 62"(1.57m) OVERALL WIDTH 26.75" (0.68m) OVERALL HEIGHT 42" (1.07m)

Part No. 890564

Page 1 of 8

Form No. F022502A

4 IN THE INTEREST OF SAFETY

BEFORE STARTING ENGINE, READ AND UNDERSTANDTHE “ENTIRE OPERATOR'S MANUAL & ENGINE MANUAL.”

THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.

WARNING: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

 

 

 

 

 

 

13. DO NOT tamper with governor springs,

22. DO NOT run engine without air cleaner

WARNING: DO NOT

governor links or other parts which may

or air cleaner cover.

 

 

 

change the governed engine speed.

 

 

 

23. DO NOT operate during excessive

1. DO NOT run engine in an enclosed area.

14. DO NOT tamper with the engine speed

vibration!

 

 

 

 

Exhaust gases contain carbon monoxide, an

selected by the engine manufacturer.

24. DO NOT leave machine unattended

odorless and deadly poison.

 

 

 

15. DO NOT check for spark with spark

while in operation.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. DO NOT place hands or feet near moving

plug or spark plug wire removed. Use an

25. DO NOT park machine on a steep

approved tester.

 

or rotating parts.

 

 

 

 

grade or slope.

 

 

 

 

 

 

 

 

 

 

 

 

 

3. DO NOT store, spill or use gasoline near

16. DO NOT crank engine with spark plug

WARNING: DO

 

 

removed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

an open flame, or devices such as a stove,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. ALWAYS DO remove the wire from the

furnace, or water heater which use a pilot

17. DO NOT strike flywheel with a hard

light or devices which can create a spark.

spark plug when servicing the engine or

object or metal tool as this may cause

 

 

 

 

 

 

equipment TO PREVENT ACCIDENTAL

4. DO NOT refuel indoors where area is not

flywheel to shatter in operation. Use

STARTING.

 

 

 

proper tools to service engine.

 

 

 

well ventilated. Outdoor refueling is

 

 

 

 

 

 

 

 

 

 

 

 

 

2. DO keep cylinder fins and governor

recommended.

 

 

 

18. DO NOT operate engine without a

 

 

 

parts free of grass and other debris

 

 

 

 

 

 

muffler. Inspect periodically and replace, if

5. DO NOT fill fuel tank while engine is

 

which can affect engine speed.

 

 

 

necessary. If engine is equipped with

 

 

running. Allow engine to cool for 2 minutes

 

 

 

 

 

 

 

muffler deflector, inspect periodically and

3. DO pull starter cord slowly until resis-

before refueling. Store fuel in approved

 

 

replace, if necessary, with correct deflector.

tance is felt. Then pull cord rapidly to avoid

safety containers.

 

 

 

 

 

 

 

 

 

 

kickback and prevent hand or

arm

 

 

 

 

 

 

 

 

 

 

6. DO NOT remove fuel tank cap while

 

19. DO NOT operate engine with an

injury.

 

 

 

 

 

accumulation of grass, leaves, dirt or other

 

 

 

 

 

 

 

engine is running.

 

 

 

4. DO examine muffler periodically to be

 

 

 

combustible material in the muffler area.

 

 

 

 

 

 

sure it is functioning effectively. A worn or

7. DO NOT operate engine when smell of

 

 

 

 

 

 

 

 

leaking muffler should be repaired or

gasoline is present or other explosive

 

20. DO NOT use this engine on any forest

 

replaced as necessary.

 

 

 

conditions exist.

 

 

 

covered, brush covered, or grass covered

 

 

 

 

 

 

 

 

 

 

 

 

 

8. DO NOT operate engine if gasoline is

unimproved land unless a spark arrester is

5. DO use fresh gasoline. Stale fuel can

installed on the muffler. The arrester must

gum carburetor and cause leakage.

spilled. Move machine away from the spill

be maintained in effective working order by

6. DO check fuel lines and fittings fre-

and avoid creating any ignition until the

 

 

the operator. In the State of California the

gasoline has evaporated.

 

 

 

quently for cracks or leaks. Replace if

 

 

 

above is required by law (Section 4442 of

 

 

 

 

 

 

necessary

 

 

 

 

9. DO NOT transport unit with fuel in tank.

the California Public Resources Code).

 

 

 

 

 

 

 

 

 

 

 

Other states may have similar laws.

7. Follow engine manufacturer operating

 

 

 

 

 

 

10. DO NOT smoke when filling fuel tank.

Federal laws apply on federal lands.

and maintenance instructions.

 

 

 

 

 

 

 

 

 

 

 

 

 

11. DO NOT choke carburetor to stop

 

21. DO NOT touch hot muffler, cylinder, or

8. Inspect machine and work area before

 

fins because contact may cause burns.

starting unit.

 

 

 

engine.

 

 

 

 

 

 

 

 

 

THE BRIGGS AND STRATTON ENGINE ON THIS EQUIPMENT CANNOT BE SOLD IN THE STATE

 

 

 

 

 

 

12. DO NOT run engine at excessive

 

OF CALIFORNIA.

 

 

 

 

 

 

 

 

speeds. This may result in injury & /or

6

 

SOUND

 

 

 

7

VIBRATION

 

 

damage to unit.

 

 

 

 

 

 

 

 

 

 

VIBRATION LEVELS 2.0g

 

 

 

 

 

Sound tests conducted were in accordance with 2000/14/EEC

 

 

Vibration levels at the operators handles were

 

 

 

 

 

and were performed on 2/21/2002 under the conditions listed:

 

 

measured in the vertical, lateral, and longitudinal

5

 

TABLE OF CONTENTS

NOTE: Sound power level listed is the highest value for any model in this manual. Please

directions using calibrated vibration test equipment.

 

Tests were performed on 11/20/98 under the conditions

 

refer to serial plate on the unit for the sound power level for your model.

 

 

 

 

 

 

 

 

 

listed:

 

 

 

 

 

SAFETY INSTRUCTIONS

2

 

 

Sound level of 98 dBA at operator position

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GENERAL SAFETY

3

 

 

 

GENERAL CONDITION:

Sunny

 

 

GENERAL CONDITION:

 

Sunny

 

ASSEMBLY

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

50°

F (10.0° C)

 

 

 

 

 

 

 

 

 

 

 

 

LABELS . . . . . . . . . . . . . . . . . . . . 4

 

 

TEMPERATURE:

45° F (7.2° C)

 

 

 

TEMPERATURE:

 

OPERATION

5

 

 

 

 

 

 

 

 

 

WIND SPEED:

8 MPH (12.9 kmh)

 

 

 

 

WIND SPEED:

5 MPH (8.1 kmh)

 

 

 

 

PARTS DRAWING & LIST

6 - 7

104 dB

 

 

 

 

 

 

 

 

 

 

 

 

west

 

 

 

South West

 

 

 

 

 

 

MAINTENANCE

7 - 8

WIND DIRECTION:

 

 

 

 

WIND DIRECTION:

 

 

 

 

 

 

 

 

 

 

 

 

TROUBLESHOOTING . . . . . . .

8

 

 

 

HUMIDITY:

60 %

 

 

 

HUMIDITY:

 

54 %

 

 

WARRANTY PROCEDURE

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30.23" Hg (768mm Hg)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BAROMETRIC PRESSURE:

30.18" Hg (767mm Hg)

 

 

BAROMETRIC PRESSURE:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Part No. 890564

Page 2 of 8

Form No. F022502A

8 GENERAL SAFETY

For your safety and the safety of others, these directions should be followed:

Do not operate this machine without first reading owner's manual and engine manufacturer's manual.

Use of Ear Protection is recommended while operating this machine.

Use of Eye and Breathing protection is recommended when using this machine, especially in dry

and dusty conditions. Optional bag cover directs dust toward ground, away from the operator.

·DO NOT place hands or feet inside nozzle intake opening, near debris outlet or near any moving parts.

·DO NOT start engine without debris bag and quick disconnect connected firmly in place to exhaust outlet.

·DO NOT start or operate machine with debris bag zipper open.

·DO NOT operate during excessive vibration.

·DO NOT remove bag until engine has been turned off and has come to a complete stop.

·DO NOT remove hose kit cap on nozzle until engine has been turned off and has come to a complete stop.

·DO NOT operate machine with hose cap, bag or hose removed.·DO NOT use this machine for vacuumingexclusively sand, dust, fine dirt, rock, glass, string like material, grain, rags,

cans, metal, bark or water.

·DO NOT operate this machine on slopes greater than 20%.·DO NOT pick up any hot or burning debris, or any toxic or explosive material.

·DO NOT allow children to operate this equipment.

9 ASSEMBLY

Read all safety and operating instructions before assembling or starting this unit.

PUT OIL IN ENGINE BEFORE STARTING

Your Billy Goat is shipped from the factory in one carton, completely assembled except for the upper handle, debris bag, and bag quick disconnect.

1.ASSEMBLE Lift upper handle (item 6), remove items 8, 74, & 30 from lower handle (item 27). Attach upper and lower handle as shown,

and securely tighten nuts (item 74).

2.UNFOLD the debris bag (item 1) and fasten bag neck to bag quick disconnect (item 83). Attach firmly to housing exhaust (item 52) see fig. 2.

3.ATTACH bag hanger strap to bag supports (item 11), preassembled to upper handle.

5.CONNECT spark plug wire.

10 PACKING CHECKLIST

These items should be included in your carton. If any of these parts are missing, contact your dealer.

6

27

8

QUICK DISCONNECT

Literature

Assembly

74 32

Engine

Manual

Fig. 2

Part No. 890564

Page 3 of 8

Check

Debris Bag

890304 KD

Check Connector

Quick Disconnect 890176

Check

Literature Assy 890454

Per Model

Check

Briggs & Stratton

MS9984 Multi-Language

Form No. F022502A

11 LITERATURE ASSY P/N 890454

Owner's

Literature Check-

Manual

list

Owner's

 

Check

 

 

 

 

Manual

 

 

890564

Literature

Check

Literature

 

KD

KD

 

 

Accessories

Accessories

 

 

890409

 

 

Warranty

Check

Warranty

 

Card

 

Card 400972

EU Declaration

Check

EU Declaration

 

of Conformity &

of Conformity

 

& EU

 

EU Distributor

Distributor List

 

List 890393

12 INSTRUCTION LABELS

These labels should be included on your Vacuum. If any of these labels are damaged, replace them before putting this equipment into operation. Item and part numbers are given to help in ordering replacement labels..

WARNING

EXPLOSIVE FUEL

400268

 

STOP ENGINE AND ALLOW T O

COOL BEFORE REFUELING.

Label Do Not Fill While

Engine Is Hot

Item 63 Part No.400268

DANGER

Label Danger

Keep Hands

and Feet

Away

Item 29 Part

No.400424

Label Read Owner's

Manual Item 84

Part No.890301

810736

890254

Label Danger Flying Material

Label Ear Eye Breathing

Item No. 86 Part No. 890254

Item 62 Part No.810736

 

Debris Bag

Label item 1

13 ENGINE LABELS

UPD

ATE

 

Part No. 890564

Page 4 of 8

Form No. F022502A

14 Operation

INTENDED USE: This machine is designed for vacuuming leaves, grass clippings and other types of organic litter.

Debris mixed with cans, bottles and small amounts of sand can be vacuumed; however, it is not this machine's primary purpose. Vacuuming cans, bottles and sand will affect the longevity of your machine.

Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects. Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 8).

Like all mechanical tools, reasonable care must be used when operating machine.

Inspect machine work area and machine before operating. Make sure that all operators of this equipment are trained in general machine use and safety.

PUT OIL IN ENGINE BEFORE STARTING.

14.1STARTING

ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used.

Engine must be level when checking and filling oil and gasoline.

FUEL VALVE: Move fuel valve to "ON" position (when provided on engine).

PRIMER: Push primer per engine instructions.

IF YOUR UNIT FAILS TO START:

See Troubleshooting on page 8.

14.2VACUUMING OPERATION

VACUUM NOZZLE HEIGHT ADJUSTMENT: is raised and lowered by pulling slightly upward on handle and pulling height adjust control (item 23) out on left side of handle. (Note: Top notch is intended for use with hose kit to cut off intake air.)

FOR MAXIMUM PICKUP: Adjust nozzle close to debris, but without blocking airflow into the nozzle.NOTE: Never bury nozzle into debris.

CLEARING A CLOGGED NOZZLE

& EXHAUST: Turn engine off and wait for impeller to stop completely and disconnect spark plug wire. Wearing durable gloves, remove clog.Danger, the clog may contain sharp materials. Reconnect spark plug wire.

14.10COMPOST

Vacuumed leaves, grass and other organic material from your own yard can be emptied into a pile or composter to provide enriched soil for later use as fertilizer in gardens and flower beds (see fig. 3).

Note: Allow green chips to dry before spreading around living plants.

Part No. 890564

Page 5 of 8

14.3DEBRIS BAG

Debris bags are normal replaceable wear items.

Note: Frequently empty debris to prevent bag overloading with more weight than you can lift.

An optional bag and dust cover is available for use where debris will be vacuumed in dusty conditions (see Optional Accessories shown on page 1).

DO NOT place bag on or near hot surface, such as engine. Your new bag requires a break-in period to condition the pores of the material against premature blockage. The entire bag surface serves as a filter, and must be able to breath to have good vacuum performance.

Be sure engine has come to a complete stop before removing or emptying bag.

This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings page 2-3).

However, many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas. Dust is the greatest cause of lost vacuum performance. However, following these rules will help maintain your machine's ability to vacuum in dusty conditions:

The debris bag must be cleaned more frequently. A vacuum with a clean, pillow soft bag will have good pickup performance. One with a dirty, tight bag will have poor pickup performance. If dirty, empty debris and vigorously shake bag free of dust.

Machine orpressure-washdebris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before use.

Having one or more spare debris bags is a good way to reduce down time while dirty bags are being cleaned.

DO NOT leave debris in bag while in storage.

14.4HANDLING &TRANSPORTING:

Using two people to lift machine is recommended. Lift holding the handle and front of nozzle. Secure in place during transport.

14.5STORAGE

Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.

If engine is to be unused for 30 days or more, prepare as follows:

Be sure engine is cool. Do not smoke. Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Run engine until fuel tank is empty and engine runs out of gasoline.

NOTE: Fuel stabilizer (such asSta-Bil)is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 min. after adding stabilizer to allow it to reach the carburetor.

Do not store with debris in bag.

Form No. F022502A

15 PARTS DRAWING

KD410

Part No. 890564

Page 6 of 8

Form No. F022502A

Item

16

PARTS

Description

KD410

QTY

 

No.

LIST

Part No.

 

 

1

TURF QUICK DEBRIS BAG (SEE ACCESSORIES FOR OTHER OPTIONS)

890305

1

 

4

NUT LOCK (1/4 - 20)

*8160001

6

 

5

SCREW CAP ( 1/4 - 20 x 1-1/2HEX )

*8041008

4

 

6

HANDLE ASS’Y (incl. items 5(5),11(2))

900054

1

 

7

AXLE HEIGHT ADJUST

890389

1

 

8

SCREW HANDLE 5/16 - 18 x 1 3/4

*8041031

1

 

9

SCREW HANDLE 5/16 - 18 x 2 1/2

*8041034

1

 

11

BAR BAG SUPPORT

900039

2

 

12

DOOR EXHAUST ASS’Y (incl. item 62 )

890148

1

 

14

BOLT-CARRIAGE1/4x3/4

*8024021

2

 

16

WASHER 1/4 FC ZP

*8171002

2

 

18

BRACKET - HEIGHT ADJUSTMENT

890021

1

 

20

SPRING

 

 

900136

1

 

21

TIRE - ONLY (PER ASSY)

900507

1

 

22

PIN - HAIR COTTER

900471

1

 

23

CABLE HEIGHT ADJUSTMENT

890019

1

 

24

BOLT - CARRIAGE 5/16 - 18 x 4 1/2

*8024054

4

 

26

NUT LOCK 5/16 - 18 HEX

*8160002

4

 

27

HANDLE LOWER KD510

890346

1

 

28

PLATE HANDLE SUPPORT

900933

1

 

29

LABEL DANGER CUT FINGER

400424

2

 

30

WASHER FLAT CUT 5/16

*8171003

2

 

32

ROPE GUIDE

 

830533

2

 

34

WHEEL ASS’Y

(incl. items 21)

900509

4

 

35

WASHER 0.75 “C”

900997

0-1

 

40

SCREW CAP 1/4 - 20 x 1 - 1/4

*8041007

4

 

42

SCREW SELF TAPPING 10 - 24 x 1/2

*8123086

1

 

43

NOZZLE MAINFRAME ASS’Y (incl. one of items 29,44,42)

890391

1

 

44

PLUG

 

 

900146

1

 

45

SCREWCAP 1/4-20X 1 3/4

8041009

1

 

47

IMPELLER ASS’Y (incl. items 49, 50, 51, 59 )

900168

1

 

49

KEY

 

 

900162

2

 

50

WASHER LOCK 3/8 TWISTED TOOTH

400502

1

 

51

SCREW CAP 3/8 -24x 1 (HARDENED)(TORQ.50FT-LBS)(68N.m)

900154

1

 

52

HOUSING ASS’Y (incl. items 12, 14, 15, 16, 86)

890371

1

 

53

ENGINE BRIGGS AND STRATTON 4 HP QUATTRO

890565

1

 

56

SCREW CAP 3/8 - 1-1/2TAPTITE

890408

3

 

58

WASHER FLAT 1/2 SAE

*8172011

4

 

60

HT ADJUST ASSY

890013

1

 

61

1/2-13CAP NUT NP W/PATCH

890530

4

 

62

LABEL DANGER FLYING MATERIAL

810736

1

 

63

LABEL DO NOT FILL WHEN ENGINE IS HOT

400268

1

 

68

PLATE TOP ASS’Y (incl. items 14, 15, 29, 48, 69, 70, 71, 72)

890402

1

 

71

SCREW CAP 1/4 - 20 x 1/2 HWH

890359

15

 

74

NUT LOCK 5/16 - 18 THIN HT.

*8161041

2

 

76

PLATE UPPER HEIGHT ADJUST

890005

1

 

83

CONNECTOR BAG QUICK

890176

1

 

* Denotes standard hardware item that may be purchased locally.

17 MAINTENANCE

Use only a qualified mechanic for any adjustments, disassembly or any kind of repair .

WARNING: TO AVOID PERSONAL INJURY, ALWAYS

TURN MACHINE OFF, MAKE SURE ALL MOVING

PARTS COME TO A COMPLETE STOP.

DISCONNECT SPARK PLUG WIRE

BEFORE SERVICING UNIT.

ENGINE: See engine manufacturer operator's instructions.

DEBRIS BAG: See page 5.

RECONNECT SPARK PLUG WIRE,

GUARDS, BAG, CAPS AND / OR

HOSE BEFORE STARTING ENGINE.

17.1IMPELLER REMOVAL

1.Wait for engine to cool and disconnect spark plug.

2. Drain fuel and oil from the engine.

3. Remove bag, quick release, and upper handle.

4. Remove housing top plate by removing bolts around outside of housing.

5.Leaving engine fastened to top plate, remove impeller bolt and lock washer and slide impeller off crankshaft (A puller may be required).

6.If impeller slides off freely, proceed to step 9.

(Do not drop impeller).

7.If impeller does not slide off crankshaft, place two crowbars between impeller and housing on opposite sides. Pry impeller away from engine until it loosens. Using a penetrating oil can help loosen a stuck impeller.

8.If the impeller cannot be loosened, obtain a 1” (25.4mm) longer bolt of the same diameter and thread type as the impeller bolt. Invert engine and impeller and support engine above ground to prevent recoil damage. Thread longer bolt by hand into the crankshaft until bolt bottoms. Using a suitable gear or wheel puller against the bolt head and the impeller back-plate(near the blades), remove impeller from shaft.

Part No. 890564

Page 7 of 8

Form No. F022502A

17 MAINTENANCEcontinued

17.1IMPELLER REMOVAL continued

9.To reinstall impeller, use a new impeller bolt and lockwasher and use exactly the same crankshaft impeller shim washers as were removed during disassembly (unless they were damaged).Note: your unit may or may not have required the use of shim washers.

10. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs. (68 N.m) (see item 51 on page 11).

11.Reinstall engine and impeller onto housing in reverse order of removal.

12.Before connecting spark plug wire, slowly pull engine starting rope to insure that impeller rotates freely.

13. Reinstall spark plug wire.

17.2 Maintenance Schedule

Follow these hourly

maintenance intervals.

 

 

Maintenance Operation

Every

Every 5 hrs

 

Use

or (Daily)

Engine (See Engine Manual)

Check for excessive vibration

Clean Debris Bag

Check bag strap tightness

Inspect for loose parts

Inspect for worn or damaged parts

MAINTENANCE HISTORY

Date of

Service Performed

Service

 

18

TROUBLESHOOTING

 

Before Requesting Service Review These Suggestions

 

Problem

 

Possible Cause

 

Solution

 

 

 

Will not vacuum or has poor vacuum perfor-

 

Dirty debris bag. Nozzle height set too high or too low.

 

Clean debris bag. Shake bag clean or wash. Adjust

 

 

mance.

 

Hose kit cap missing. Clogged nozzle or exhaust.

 

nozzle height. Check for hose kit cap. Unclog nozzle or

 

 

 

Excessive quantity of debris.

 

exhaust (see page 5). Allow air to feed with debris.

 

 

 

 

 

Abnormal vibration.

 

Loose or out of balance impeller or loose engine.

 

Check impeller and replace if required. Check

 

 

 

 

 

Engine.

 

 

 

 

 

Engine will not start.

 

Out of gasoline. Bad or old gasoline. Spark Plug wire

 

Check gasoline. Connect spark plug wire. Clean or

 

 

 

disconnected. Dirty air cleaner.Safety Interlock engaged.

 

replace air cleaner. Or contact a qualified service

 

 

 

 

 

person. Quick Disconnect not fully engaged.

 

 

 

 

 

Engine is locked, will not

 

Engine problem.

 

Contact an engine servicing dealer for engine

pull over.

 

 

 

problems.

 

 

 

 

 

 

20.1

Engine Service and Warranty

Contact your nearest engine manufacturer's autho-

 

 

 

rized servicing dealer.

19

Serial Plate

Record your machine model, serial number

and date-of-purchaseand where purchased

 

 

 

1803 S. Jefferson

 

P.O. Box 308

 

Lee's Summit,

 

MO

64063 / USA

R

Tel (816) 524-9666

 

 

Fax (816) 524-6983

104 dB

 

Model

 

 

 

Serial No.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unit(Weight)

 

 

 

 

Engine Power

 

 

 

 

 

 

 

 

 

lbs.

 

 

kg

 

 

 

kW

 

 

rpm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

min-1

Purchase

 

 

 

Purchased

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Date

 

 

 

 

from

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Part No. 890564

WARRANTY PROCEDURE

20Please fill in the WARRANTY CARD and send the upper part to Billy Goat. The WARRANTY terms are stated on the lower part which remains with the user. Whenever a Billy Goat Machine is faulty due to a defect in material and / or workmanship, the owner should make a warranty claim as follows:

The Machine should be taken to the dealer from whom it was purchased or to an authorized Billy Goat dealer.

The owner should present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt.

The Warranty Claim will be filled in by the authorized Billy Goat Dealer, who will send it with the faulty part to Billy Goat headquarters.

The Quality / Service department at Billy Goat headquarters will study the claim and parts and will notify their conclusions.

The decision by the Quality / Service department at Billy Goat headquarters to approve or reject a Warranty claim is final and binding.

Note: To process a Warranty Claim, it is necessary to quote the Model & Serial number who are printed on the Billy Goat Serial Plate.

BILLY GOAT INDUSTRIES INC.

1803 S JEFFERSON LEE'S SUMMIT, MO 64082 / USA

R

PHONE: 816-524-9666FAX:816-524-6983www.billygoat.com

Page 8 of 8

Form No. F022502A

 

Gardening Supply

 

 

Patio Barbecues

Outdoor Barbecues

Landmann Barbecues

Gas Barbecues UK

Charcoal Barbecues

Gas Barbecues

Cheap Gas Barbecues

Masonry Barbecues

Brush Cutters

Brushcutters

Blower Vacs

Chain Saws

Chainsaws

Cultivators

Cylinder Lawn Mowers

Echo Chainsaws

Echo Strimmers

Electric Chainsaws

Fertiliser Spreaders

Garden Blowers

Garden Rollers

Lawn Rollers

Garden Shredders

Garden Tractors

Garden Vacuums

Hayter Lawn Mowers

Hedge Cutters

Hedgecutters

Hover Mowers

Husqvarna chainsaws

Kawasaki Brush Cutters

Kawasaki

Strimmers

Lawn Mowers

Scarifiers

Lawn Tractors

Leaf Blowers

Leaf Vacuums

Petrol Chainsaws

Petrol Hedge Cutters

Ride on lawn

mowers

Ride on mowers

Rotary Mowers

Rotavators

Ryobi Strimmers

Electric Garden

Petrol Garden

ALKO Garden Shredders

Cheap Garden

Shredders

shredders

Shredders

Garden Patio Heaters

Outdoor Patio Heaters

Gas Patio Heaters

Patio Heaters

Patio Heater Covers

Garden Heaters

Greenhouse Heaters

Green house

heaters

Gas Greenhouse

Stainless Steel Patio

Table Top Patio Heaters

Patio Heaters UK

heaters

Heaters

Grit Spreaders

Gardena Hedgecutters

Kawasaki brushcutters

Petrol Strimmers

Patio Heaters with

Christmas Gardening

Midgeater Plus

Barbecues

Covers

Gifts

Cylinder Mowers