Beko B-680TDA735 User Manual

Size:
282.76 Kb
Download

Congratulations on your choice of a

 

quality Appliance which has been designed to give you

 

 

service for many years.

 

 

WARNING !

IMPORTANT !

DO NOT connect your appliance to the electricity supply until all packing and transit protectors have been removed.

Leave to stand for at least 4 hours before switching on to allow compressor oil to settle if transported horizontally.

If you are discarding an old refrigerator with a lock or latch fitted to the door, disable the lock/latch, ensure that it is left in a safe condition to prevent the entrapment of young children.

This fridge/freezer must only be used for its intended purpose i.e the storing and freezing of edible foodstuff.

Do not dispose of the appliance on a fire. At BEKO, the care and protection of our environment is an ongoing commitment. This appliance which is among the latest range introduced is particularly environmentally friendly. Your appliance contains non CFC / HFC natural substances in the cooling system (Called R600a) and in the insulation (Called cyclopentane) which are potentially flammable if exposed to fire. Therefore, take care not to damage, the cooling circuit / pipes of the appliance in transportation and in use. In case of a damage do not expose the appliance to fire, potential ignition source and immediately ventilate the room where the appliance is situated.

We suggest you contact your local authority for disposal information and facilities available.

We do not recommend use of this appliance in an unheated, cold room.

(E.g.: garage, conservatory, annex, shed, out-houseetc.) “See Page 5, Item 2 under Installation Instructions”

To obtain the best possible performance and trouble free operation from your appliance it is very important to carefully read these instructions.

On delivery, check to make sure that the product is not damaged and that all the parts and accessories are in perfect condition.

•Take care to ensure that the plug remains readily accessible. Do not use multiple adapter bar or extension cable.

Failure to observe these instructions may invalidate your right to free service during the guarantee period.

WARNINGKeep ventilation openings, in the appliance enclosure or in the built-instructure, clear of obstruction.

WARNINGDo not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

WARNINGDo not damage the refrigerant circuit.

WARNINGDo not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

• We suggest you keep these instructions in a safe place for easy reference.

Fridge Freezer

PERFORMANCE

TDA 735

 

 

 

 

 

Energy efficiency class

 

A

 

 

Energy consumption - Kwh/year

313

Net storage - vol fresh food ltrs (cu.ft.)

330

(11.6)

Net storage - vol frozen food ltrs (cu.ft.)

102

(3.6)

Total net vol - ltrs (cu.ft.)

432

(15.2)

Frozen food compartment rating

4 STAR

Conservation time from failure

23 hrs.

Freezing capacity fresh food - kg

4.5

Climate class

SN

Operating noise level dB(A)

41

1

 

 

CONTENTS

PAGE

 

 

 

SAFETY FIRST / ELECTRICAL REQUIREMENTS

3

 

 

 

TRANSPORTATION INSTRUCTIONS

4

 

 

 

INSTALLATION INSTRUCTIONS

5

 

 

 

 

GETTING TO KNOW YOUR BEKO FRIDGE / FREEZER

6

 

 

 

REVERSING THE DOORS

7-8

 

 

 

SUGGESTED ARRANGEMENT OF FOOD IN THE FRIDGE / FREEZER

9

 

 

 

TEMPERATURE CONTROL AND ADJUSTMENT

10-11

 

 

 

STARTING

11

 

 

 

STORING FROZEN FOOD

12

 

 

 

FREEZING FRESH FOOD

12

 

 

 

MAKING ICE CUBES

12

 

 

 

DEFROSTING

13

 

 

 

CLEANING AND CARE

14

 

 

 

REPLACING THE INTERIOR LIGHT BULB

15

 

 

 

DO'S AND DON'TS

16

 

 

 

ENERGY SAVING TIPS

17

 

 

 

PROBLEM SOLVING

17

 

 

 

GUARANTEE DETAILS

18

 

 

 

HOW TO OBTAIN SERVICE

19

 

 

 

2

ELECTRICAL REQUIREMENTS

Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating plate inside the appliance corresponds to your electricity supply. Rating label is on the left hand side of the fridge inner liner.

We recommend that this appliance is connected to the mains supply via a suitable switched and fused socket in a readily accessible position. Should the mains lead of the appliance become damaged or should it need replacing at any time, it must be replaced by a special purpose made mains lead which can only be obtained from a BEKO Authorised Service Agent.

WARNING! THIS APPLIANCE MUST BE EARTHED

If the fitted moulded plug is not suitable for your socket, then the plug should be cut off and an appropriate plug fitted. Destroy the old plug which is cut off as a plug with bared cord could cause a shock hazard if inserted into a socket elsewhere in the house.

The moulded plug on this appliance incorporates a 13 A fuse. Should the fuse need to be replaced an ASTABEAB approved BS 1362 fuse of the same rating must be used. Do not forget to refit the fuse cover. In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been fitted. Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are available from any good electrical store.

IMPORTANT! FITTING A DIFFERENT PLUG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

As the colours of the wires in the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mains lead of this appliance may

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

not correspond with the coloured

 

 

E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

markings identifying the terminals

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in your plug proceed as follows:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GREEN &

 

 

 

 

 

 

 

6mm.

 

 

 

 

 

 

 

 

(See diagram).

 

 

YELLOW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Connect the green-yellowor

 

GREEN

32mm.

 

 

 

 

 

 

L

 

 

 

 

 

 

 

 

FITTED WITH 1362 13A FUSE ALWAYS BS 1362 REPLACEMENT CARTRIDGE FUSE

green (Earth) wire to the terminal

 

 

 

 

 

 

 

 

BROWN

 

 

 

 

 

 

 

 

in the plug marked 'E' or with

 

N

 

 

 

 

 

 

 

 

OR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RED

 

 

 

 

the symbol

 

 

 

or coloured

 

BLUE

 

 

22mm.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

green and yellow or green.

 

OR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BLACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Connect the blue (Neutral) wire

 

 

 

 

 

 

 

 

 

 

 

 

 

12mm. 6mm.

 

FUSE

 

 

 

 

 

 

 

 

 

6mm.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to the terminal in the plug

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BS FIT

 

 

 

 

 

 

 

 

CORD GRIP

 

 

 

 

 

marked 'N' or coloured black.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3. Connect the brown (Live) wire to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the terminal in the plug marked 'L'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or coloured red.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

With alternative plugs a 13 A fuse must be fitted either in the plug or adaptor or in the main fuse box.

If in doubt contact a qualified electrician.

3

TRANSPORTATION INSTRUCTIONS

1.The appliance should be transported only in a vertical upright position. The packing as supplied must be intact during transportation.

2.If during the course of transport the appliance has to be transported horizontally, it must only be laid on its right hand side when standing in the front of the appliance. After bringing it to upright position,it must not be operated

for at least 4 hours to allow the system to settle.

3.Failure to comply with the above instructions could result in damage occuring to the appliance. The manufacturer will not be held responsible if these instructions are disregarded.

4.The appliance must be protected against rain, moisture and other atmospheric influences.

5.When positioning your appliance take care not to damage your flooring, pipes, wall coverings etc. Do not move the appliance by pulling by the door or handle.

6.Empty any water in the drain tray before moving. See section ‘Defrosting’ and ‘Care & cleaning’ for further information.

IMPORTANT : Care must be taken while cleaning / carrying the appliance to avoid touching the bottom of the condenser metal wires at the back of the appliance as you might injure your fingers and hands.

IMPORTANT : This appliance is not designed for stacking with any other appliance.

Do not attempt to sit or stand on top of your appliance as it is not designed for such use. You could injure yourself or damage the appliance.

“IMPORTANT: Make sure that mains cable is not caught under the appliance during and after carrying / moving the appliance, to avoid the mains cable becoming cut or damaged."

Do not allow children to play with the appliance or tamper with the controls. BEKO plc declines to accept any liability should the instructions not be followed.

4

IMPORTANT

INSTALLATION INSTRUCTIONS

1. The space in the room where the appliance is installed must not be smaller than 10 cubic metres.

2. Do not put your fridge freezer in a cold room where the temperature is likely to go below +5 degrees C (41 degrees F) during night time and/or especially in winter.

This fridge freezer has been designed to operate in ambient temperatures between +5 and +32 degrees C (41 and 90 degrees F) Therefore if the appliance is installed in an unheated/cold room (eg: conservatory/annex/ shed/garage etc) then the appliance will not operate causing the freezer compartment to run warmer and as a result the storage time of frozen food may be reduced.

3. Do not place the appliance near cookers, radiators or in direct sunlight as this will cause your appliance to work harder. If installed next to a source of heat or freezer, maintain the following minimum side clearances:

From Cookers

50 mm (2")

From Radiators

300 mm (12")

From Freezers

25 mm (1")

4. Make sure that sufficient room is provided around the appliance to ensure free air circulation.

Fit the Two plastic wall spacers supplied with the appliance rotating 1/4 turn to the condenser at the back of the appliance (See Diagram).

5.The fridge/freezer should be located on a smooth surface. The two front feet can be adjusted as required. To ensure that your appliance is standing upright adjust the two front feet by turning clockwise or anti-clockwise,until the product is in firm contact with the floor. Correct adjustment of feet avoids excessive vibration and noise.

6.Refer to cleaning and care section to prepare your appliance for use.

7. .A special receptacle is supplied to store the mains plug during transit. The receptacle is fixed at the back of the

cabinet, on the left hand side of the compressor. (See diagram) Gently remove the plug from the receptacle. Never pull

the mains cord, you may damage the appliance. In the case of transportation, ensure you locate the plug in the receptacle provided to avoid transit damage. 5

GETTING TO KNOW YOUR BEKO FRIDGE / FREEZER

1

2

11

3

4 12

5

5

12 5

5

12

6

7

8

13

9

10

1.

Ice cube tray

8.

Salad crispers

2.

Freezer shelf

9.

Kick plate

3.

Interior light

10.

Front wheels behind

4.

Thermostat knob

 

adjustable feet

5.

Fridge compartment shelves

11.

Egg tray

6.

Crisper humidity-controlknob

12.

Door shelf - 3 pcs.

7.

Crisper cover

13.

Bottle rack

6

REVERSING THE DOORS

We recommend that you reverse doors before switching on for the first time.

Tools required: Small and medium size flat and cross-headedscrewdrivers, a pair of pliers.

Spare Parts supplied in the plastic bag: The following parts, which are exclusively for left hand side fitted hinge operation are supplied in a plastic bag with the appliance:

-Upper door top trim hinge covers – there are 2 different parts, one for each side of top trim.

-Upper door middle hinge bushing/door stopper assembly.

We suggest you keep all the parts supplied in the plastic bag and also parts, which have been removed when reversing doors, in a safe place for possible future, re-use.

IMPORTANT: We suggest you ask somebody to help you when moving the appliance around and to hold doors when removing / re-fittinghinges and doors to avoid any injury and damage to the product.

Please refer to diagrams supplied. To follow numbers in brackets below, refer to the main diagram.

1.Switch off the appliance at the socket outlet and pull out the mains plug.

2.Remove all loose items and fittings and food, if any, from inside the appliance and door racks.

3.Gently prise off plastic hinge cover of upper door top trim using a small flat-headedscrewdriver. (1)

4.Gently tilt the appliance back against a strong wall on its rear side sufficiently to allow the lower hinge to be removed. Take care to protect the appliance, your wall and floor coverings. You can utilise the original packaging to do this. Once you tilt the appliance back, check to make sure the appliance is completely stable and safe before you carry on. (2)

5.Unscrew and remove the lower hinge using a cross-headedscrewdriver while holding the lower door firmly.(3)

6.Remove lower door carefully off the middle hinge and stand door upright in a safe place.(4)

7.Open upper door and unscrew and remove the middle hinge while holding the upper door firmly. Use a flat-headedscrewdriver. Middle hinge will need to be rotated 180 degrees beforere-fittingon the opposite side.(5)

8.Remove upper door carefully off the upper hinge and stand door upright in a safe place.(6)

9.Unscrew and remove the upper hinge using a flat-headedscrewdriver.(7)

10.Rotate the upper hinge 180 degrees and then unscrew and remove the hinge pin using a pair of pliers and re-fitto opposite side of hinge.(8)

11.Reposition plugs and hinge pin bushings on top of doors on the opposite side of both doors. Use small flatheaded screwdrivers to remove plugs and bushings. Take care not to mark doors.(9)

12.Reposition left hand side feet on the opposite side.(10)

13.Unscrew and remove the upper door middle hinge pin bushing/door stopper using a cross-headedscrewdriver. Important: This part cannot be used on the opposite side; left hand side middle hinge pin bushing/door stopper part is supplied in the plastic bag.(11)

14.Re-fitthe upper hinge on the left hand side usingflat-headedscrewdriver.(12)

15.Fit upper door left hand side middle hinge pin bushing/door stopper supplied in the plastic bag using cross-headedscrewdriver.(13)

16.Reposition three small plastic plugs on the left hand side, which are covering middle hinge holes, on the opposite side to cover holes left empty.(14)

17.Locate and re-fitupper door to upper hinge and hold the door firmly.(15)

18.Locate the middle hinge pin to middle hinge pin bushing of upper door on the left hand side and re-fitthe middle hinge.(16)

19.Reposition the two screws fitted to lower hinge holes on the left hand side at the bottom of the cabinet on the opposite side.(17)

20.Unscrew and reposition the hinge housing and steel pant on the right hand side at the bottom of the door on the opposite side. (18)

21.Locate and re-fitlower door to middle hinge pin and thenre-fitthe lower hinge on the left hand side.(19), (20)

22.Carefully stand the appliance upright and adjust the two front feet if necessary.

23.Check that doors open and close easily, they are aligned correctly and that there are no gaps allowing

air into the cabinet. If there are gaps between the door seal and the cabinet, adjust the door seal by gently pulling away from the door using fingers.

24.Check that all the hinge screws are tightened. Avoid over tightening the screws.

25.Put all items, fittings back in the appliance.

26.Fit upper door top trim plastic hinge cover. Upper door top trim hinge cover is supplied in the plastic bag.(21)

27.Wait for at least 4 hours to allow the system to settle before switching on.

28.Once the correct storage temperatures have been reached in the appliance, put back all the food.

(8)

(13)

 

7

20

 

 

1

 

1

 

 

 

6

 

2

14

5

 

11

 

 

 

 

 

 

 

 

13

9

 

 

 

 

45°

4

10 3

18

21

12 8

180°

15

16

19

17

20

7

8

SUGGESTED ARRANGEMENT OF FOOD IN THE FRIDGE/FREEZER

Arrangement Examples (See diagram)

1.Frozen food, rapid cooling of beverages, making ice cubes, freezing food.

2.Baked, chilled cooked food, dairy products.

3.Beverages, dairy products, cans.

4.Meat, sausages, cold cuts.

5.Fruit, vegetables, salads.

6.Butter, cheese.

7.Eggs.

8.Small bottles, cans, tubes.

9.Beverages, large bottles.

1

2

7

 

3 6

8 4

5 9

The following guidelines and recommendations are suggested to obtain the best results and storage hygiene.

1.The fridge compartment is for the short term storage of fresh food and drinks.

2.The freezer compartment is rated and suitable for the freezing and storage of pre frozen food. The recommendation forstorage as stated on the food packaging should be observed at all times.

3.Cooked dishes must be stored in airtight covered containers.

4.Fresh wrapped produce can be placed on the shelf. Fresh fruit and vegetables should be cleaned and stored in the crisper bins.

5.Bottles can be placed in the door section.

6.To store raw meat, wrap in polythene bags and place on the lowest shelf. Do not allow to come into contact with cooked food to avoid contamination. For safety, only store raw meat for two to three days.

7.Keep the food packed wrapped or covered. Allow hot food and beverages to cool before placing them in the fridge. Do not store explosive substances. High proof alcohol must be stored upright in sealed containers. Left over canned food should not be stored in the can.

8.Fizzy drinks should not be frozen and products such as flavoured water ices should not be consumed too cold.

9.Some fruit and vegetables suffer damage if kept at temperatures near 0°C. Therefore wrap pineapples, melons, cucumbers, tomatoes and similar produce

in polythene bags.

10.Shelves, racks, crisper bins, dairy compartments, drawers, baskets trays, flaps, bottle grippers are all removable.

11.Do not leave frozen food at room temperature to thaw; the best way to defrost food is to put it in the fridge to thaw slowly. Make sure you avoid defrosting food or food juices drip onto other food.

9

TEMPERATURE CONTROL AND ADJUSTMENT

Operating temperatures are controlled by the thermostat knob (Fig. 1) and may be set at any position between 1 and 5, 5 being the coldest position. Towards 5 you will obtain a colder fridge temperature and vice versa.

(Fig. 2) shows the ideal thermostat position where the ambient room temperature is between 15-25°C.(59-77°F)

(Fig. 3) shows the summer position where the ambient room temperature is over 25 °C. (77 °F)

(Fig. 4) shows the winter position where the ambient room temperature is near to 10 °C. (50 °F)

(Fig. 5) shows how you can switch off the appliance completely: Turn the thermostat knob to “0” (Zero) position.

(Fig. 6) By opening and closing baffles, you can adjust the amount of air flowing into the salad crispers.

“Closed” setting will keep humidity inside the salad crisper.

“Open” setting will increase air circulation thereby reduce humidity in the salad crisper.

If you wish to store food in the salad crisper for longer , you should keep the humidity adjustment knobs in the closed position.

The average temperature inside the fridge depends on the following factors:

Ambient temperature in the room (seasonal changes)

Frequency of door opening

Placing hot food inside the product

Position of the product inside the room (being exposed to sun light)

We recommend that you check the temperature with an accurate thermometer to ensure that the storage compartments are kept to the desired temperature.

Remember you must take your reading very quickly since the thermometer temperature will rise very rapidly after you remove it from the freezer. Please remember each time the door is opened cold air escapes and the internal temperature rises. Therefore never leave the door open and ensure it is closed immediately after food is put in or removed.

In case of a temporary ice build up in the fridge compartment, reduce the thermostat setting to 1, monitoring at the same time that the fridge temperature is maximum +5 degrees C [41 degrees F]. Once the ice build up disappears and the appliance starts auto defrosting again as normal, then you may increase the thermostat setting, if required.

10

1

 

2

3

4

5

 

6

STARTING

Final Check

Before you start using the fridge/freezer check that:

1.The feet have been adjusted for perfect levelling.

2.The interior is dry and air can circulate freely at the rear.

3.Clean the interior as recommended under "CLEANING AND CARE."

4.Insert the plug into the wall socket and switch on the electricity supply. When the door is open the interior light will come on.

5.You will hear a noise as the compressor starts up. The liquid and gases sealed within the refrigeration system may also give rise to noise, whether the compressor is running or not which is quite normal.

6.We recommend that you set the thermostat knob midway between 2 and 3 and monitor the temperature to ensure the appliance maintains desired storage temperatures (See section Temperature control and adjustment).

7.Front edges of the cabinet may feel warm. This is normal. These areas are designed to be warm to avoid condensation.

"Do not load the appliance immediately it is switched on. Wait until the correct storage temperature has been reached. We recommend that you check the temperature with an accurate thermometer (see; Temperature Control and Adjustment)"

11

STORING FROZEN FOOD

Your freezer is suitable for the long-termstorage of commercially frozen foods and also can be used to freeze and store fresh food.

If there is a power failure do not open the door. Frozen food should not be affected if the failure lasts for less than 23 hrs. If the failure is longer, then the food should be checked and either eaten immediately or cooked and then refrozen.

FREEZING FRESH FOOD

Please observe the following instructions to obtain the best results.

Do not freeze too large a quantity at any one time. The quality of the food is best preserved when it is frozen right through to the core as quickly as possible.

Do not exceed the freezing capacity of your appliance in 24 h which is 4.5 kg (11lb)

Placing warm food into the freezer compartment causes the refrigeration compressor to operate continuously until the food is frozen solid. This can temporarily lead to excessive cooling of the refrigeration compartment.

When freezing fresh food turn the thermostat knob towards 5. Small quantities of

food up to 1/2 kg. (1 lb) can be frozen without having to rotate the temperature control knob.

You may place fresh food to be frozen in any part of the freezer.

Take special care not to mix already frozen food and fresh food.

MAKING ICE CUBES

Fill the ice - cube tray 3/4 full with water and place it in the freezer. Loosen frozen trays with the plastic scraper provided, never use sharp edged objects such as knives, forks.

12

DEFROSTING

 

 

 

A) FRIDGE COMPARTMENT

 

 

 

The fridge compartment defrosts

 

 

2

automatically. The defrosting water runs

 

 

 

to the drain tube via a collection

Drain Tube

 

1

container at the back of the appliance (1).

 

 

 

 

(see diagram)

 

 

 

 

 

 

During defrosting water droplets may form

 

 

 

 

 

 

at the back of the fridge compartment

 

 

 

where concealed evaporator is located.

 

 

 

Some droplets may remain on the liner and

 

 

 

refreeze when defrosting is completed. Do

 

 

 

 

 

 

not use pointed or sharp edged objects such as knives, forks to remove the droplets which have frozen.

If at any time the defrost water does not drain from the collection channel, check to ensure that no food particles have blocked the drain tube. The drain tube can be cleared by pushing the special plastic plunger provided down the drain tube

(2). If the frost layer reaches about 1/4"(7 mm), reduce the setting (i.e. from 4 to 3) to restart automatic defrosting.

B) FREEZER COMPARTMENT

Defrosting is very easy and without mess thanks to a special defrost collection basin.

Defrost twice a year or when a frost layer of around 7 mm (1/4") has formed. To start defrosting procedure switch off the appliance at the socket outlet and pull out the mains plug.

All food should be wrapped in several layers of newspaper and stored in a cool place (e.g. fridge or larder).

Containers full of warm water may be placed carefully in the freezer to speed up the defrosting.

Do not use pointed or sharp edged objects such as knives, forks to remove the frost.

Never use hairdryers, electrical heaters and other similar electrical appliances for defrosting.

When defrosting has finished, sponge out any defrost water which collects at the bottom of the freezer and dry the interior thoroughly. Insert the plug in to the wall socket and switch on the electricity supply.

13

CLEANING AND CARE

**We recommend that you switch off the appliance at the socket outlet and pull out the mains plug before cleaning.

**Never use any sharp abrasive instrument, soap, household cleaner, detergent and wax polish for cleaning.

**Use luke warm water to clean the cabinet of the appliance and wipe it dry.

**Use a damp cloth wrung out in a solution of one teaspoon of bicarbonate of soda to one pint of water to clean the interior and wipe it dry.

**Make sure that no water enters the lamp and thermostat housing.

**Excess deposits of ice should be removed on a regular basis with the plastic

scraper provided. Large accumulation of ice will impair the performance of the appliance.

**If the appliance is not going to be used for a long period of time switch it off, remove all food, clean it and leave the door ajar.

**Any dust that gathers on the condenser, which is located at the back of the appliance, should be removed once a year with a vacuum cleaner.

**Check door seals regularly to ensure they are clean and free from food particles.

**Removal of door tray :

To remove a door tray, remove all the contents and then simply push the door tray upwards from the base.

**Make sure that the special plastic container (drain tray) at the back of the appliance which collects defrost water is clean at all times. If you want to remove the tray to clean it follow the instructions below :

Switch off at the socket outlet and pull out the mains plug.

Push the lug down with the tip of a screw driver & pull out with a jerk movement

Clean the drain tray and wipe it dry.

Reassemble reversing the sequence and operations.

14

REPLACING THE INTERIOR LIGHT BULB (See diagram)

Should the light fail to work switch off at the socket outlet and pull out the mains plug.

Use a cross headed screw driver to remove the light diffuser cover.

Then ensure the bulb is screwed in until it is secure in the bulb holder. Replace the

plug and switch on.

If the bulb functions, reassemble by reversing the above procedure, ensure the top cover is in place.

If the light still fails to work obtain a replacement screw cap type 15 Watt (Max) bulb from your local electrical store and then fit it as follows.

1.Switch off at the socket outlet and pull out the mains plug.

You may find it useful to remove shelves for easy access.

2. Remove the light diffuser cover screw. Use cross-headed

screw driver.

3. Pull off the light diffuser cover and remove the light

bulb.

4.Replace the burnt-outlight bulb.

5.Reassemble reversing the sequence and operations. First ensure the top of the cover is in place.

6.Carefully dispose of the burnt-outlight bulb immediately.

"Replacement light bulb can easily be obtained from a good local electrical or DIY

store."

15

DO'S AND DON'TS

DoClean and defrost your appliance regularly (See "Defrosting")

DoKeep raw meat and poultry below cooked food and dairy products. DoTake off any unusable leaves on vegetables and wipe off any soil. DoLeave lettuce, cabbage, parsley and cauliflower on the stem.

DoWrap cheese firstly in greaseproof paper and then in a polythene bag excluding as much air as possible. For best results take out of the fridge compartment an hour before eating.

DoWrap raw meat and poultry loosely in polythene or aluminium foil. This prevents drying.

DoWrap fish in polythene bags.

DoWrap food which have a strong odour or can dry out in polythene bags, aluminium foil or place in an airtight container.

DoWrap bread well to keep it fresh.

DoChill white wines, beer, lager and mineral water before serving. DoCheck contents of the freezer every so often.

DoKeep food for as short a time as possible and adhere to "Best Before", "Use by" etc. dates.

DoStore commercially frozen food in accordance with the instructions given on the packets that you buy.

DoAlways choose high quality fresh food and be sure it is thoroughly clean before you freeze it.

DoPrepare fresh food for freezing in small portions to ensure rapid freezing. DoWrap all food in aluminium foil or freezer quality polythene bags and

make sure any air is excluded.

DoWrap frozen food when you buy it and put it in to the freezer as soon as possible.

DoDefrost food in the fridge compartment.

DoRemove ice cream from the freezer 10-20minutes before serving.

Don't- Store bananas in your fridge compartment.

Don't- Store melon in your fridge. It can be chilled for short periods as long as it is wrapped to avoid it flavouring other food.

Don't- Store poisonous or any dangerous substances in your appliance. It has been designed for the storage of edible foodstuffs only.

Don't- Consume food which has been stored for an excessive time in the fridge. Don't- Store cooked and fresh food together in the same container. They should

be packaged and stored seperately.

Don't- Let defrosting food or food juices drip onto food.

Don't- Leave the door open for long periods as this will make the appliance more costly to run and cause excessive ice formation.

Don't- Use pointed sharp edged objects such as knives, forks to remove the ice. Don't- Put hot food into the appliance. Let it cool down first.

Don't- Put liquid-filledbottles or sealed cans containing carbonated liquids into the freezer as they may burst.

Don't- Exceed the maximum freezing loads (4.5 kg in any 24 hours) when freezing fresh food.

Don't- Give children ice-creamand water ices direct from the freezer. The low temperature may cause 'freezer burns' on lips.

Don't- Freeze fizzy drinks.

Don't- Try to keep frozen food which has thawed, it should be eaten within 24 hours or cooked and refrozen.

Don't- Remove items from the freezer with wet hands.

Don’t- Leave frozen food at room temperature to thaw; the best way to defrost food is to put it in the fridge to thaw slowly. Make sure you avoid defrosting food or food juices drip onto other food.

16

ENERGY SAVING TIPS

1- Ensure your appliance is installed in a well ventilated area. If the ambient temperature is low (but in no case lower than 5 degrees C), then the energy

saving will be more. In this case, check temperatures of fridge and freezer compartments with an accurate thermometer and lower the thermostat setting

(towards 1) if necessary.

2- Ensure the time between buying chilled/frozen food and placing them in your

appliance is kept at minimum, particularly in summer. We recommend you use a cool bag or a special carrier bag to carry frozen food.

3- Do not leave the door (s) of your appliance open longer than necessary and ensure they are closed properly after each opening.

4- Defrost your appliance regularly (see "Defrosting")

5- Defrost frozen food in the fridge compartment, so that frozen food acts as an ice pack to assist cooling in the fridge.

PROBLEM SOLVING

If the appliance does not operate when switched on, check whether:

The plug is inserted properly in the socket and that the power supply is on. (To check the power supply to the socket, plug in another appliance)

The fuse has blown/circuit breaker has tripped/main distribution switch has been turned off.

The temperature control has been set correctly.

New plug is wired correctly if you have changed the fitted moulded plug.

If the appliance is still not operating after the above checks, please refer to the

section on “How To Obtain Service”.

Please ensure that above checks have been made as a charge will be made if no fault is found.

GUARANTEE DETAILS

Your new Beko product is guaranteed against the cost of breakdown repairs for twelve months from the date of the original purchase.

What is covered?

Repairs necessary as a result of faulty materials, defective components or manufacturing defect.

The cost of functional replacement parts, but excluding consumable items.

The labour costs of a Beko approved repairer to carry out the repair.

What is not covered?

Transit, delivery or accidental damage or misuse and abuse.

Cabinet or appearance parts, including knobs, flaps, handles or container lids.

Accessories or consumable items including but not limited to, ice trays, scrapers, cutlery baskets, filters and light bulbs.

Repairs required as a result of unauthorised repair or inexpert installation that fails to meet the requirements contained in the user instruction book.

Repairs to products used on commercial or non-residentialhousehold premises.

Loss of frozen food in freezers or fridge/freezers. (Food loss insurance is often included within your household contents insurance policy, or may be available separately from your retailer).

Important notes.

Your Beko product is designed and built for domestic household use only.

The guarantee will be void if the product is installed or used in commercial or non-residentialdomestic household premises.

The product must be correctly installed, located and operated in accordance with the instructions contained in the User Instructions Booklet provided.

Professional installation by a qualified Electrical Domestic Appliance Installer is recommended for all Washing Machines, Dishwashers and Electric Cookers

Gas Cookers must only be installed by a CORGI (or BORD GAIS) registered Gas Installer.

The guarantee is given only within the boundaries of the United Kingdom and the Republic of Ireland.

The guarantee is applicable only to new products and is not transferable if the product is resold.

Beko disclaims any liability for incidental or consequential damages.

The guarantee does not in anyway diminish your statutory or legal rights.

17

18