Behringer 1002 User Manual
Size:
2.08 Mb
Download

ENGLISH

8

3. Installation

3.1 Mains connection

AC POWER IN

Connect the power supply to the 3-pinmains connector on the rear of the console. Use the AC adapter supplied to

connect the console to the mains. The adapter complies with all applicable safety standards.

Please use only the power supply unit provided with the console.

Never connect the XENYX to the power supply unit while the latter is connected to the mains! First connect the console to the power supply unit, then connect the power supply unit to the mains.

Please note that both the power supply unit and the mixing console heat up considerably during operation. This is completely normal.

3.2 Audio connections

You will need a large number of cables for different applications. The illustrations below show how the connectors should be wired. Be sure to use only high-gradecables.

Please use commercial RCA cables to connect the 2-trackinputs and outputs.

You can, of course, also connect unbalanced devices to the balanced inputs/outputs. To do this, use either mono plugs or stereo plugs with the ring and sleeve bridged (pins 1 and 3 in the case of XLR connectors).

Caution! Never use unbalanced XLR connectors (PIN 1 and 3 connected) on the MIC input connectors when using the phantom power supply.

input

2 1

3

1 = ground/shield

2 = hot (+ve)

3 = cold (-ve)

output

1 2

3

For unbalanced use, pin 1 and pin 3 have to be bridged

Balanced use with XLR connectors

Fig. 3.1: XLR connections

XENYX 502/802/1002/1202 User Manual

Strain relief clamp

Sleeve

Tip

Sleeve

(ground/shield)

Tip

(signal)

Unbalanced ¼" TS connector

Fig. 3.2: ¼" mono plug

strain relief clamp

sleeve ring tip

sleeve ground/shield

ring

cold (-ve)

tip

hot (+ve)

For connection of balanced and unbalanced plugs, ring and sleeve have to be bridged at the stereo plug.

Balanced 1/4" TRS connector

Fig. 3.3: ¼" stereo plug

XENYX 502/802/1002/1202 User Manual

strain relief clamp

sleeve ring tip

sleeve ground/shield

ring

right signal

tip

left signal

1/4" TRS headphones connector

Fig. 3.4: Stereo plug for headphones connection

9

4. Specifications

Mono inputs

Microphone inputs (XENYX Mic preamp)

 

Type

XLR connector, electronically

 

 

balanced, discrete input circuit

Mic E.I.N.1(20 Hz - 20 kHz)

 

 

@ 0 Ω source resistance

-134dB / 135.7 dBA-weighted

 

@ 50 Ω source resistance

-131dB / 133.3 dBA-weighted

 

@ 150 Ω source resistance

-129dB / 130.5 dBA-weighted

Frequency response

 

 

<10 Hz - 150 kHz

-1dB

 

<10 Hz - 200 kHz

-3dB

 

Gain range

+10 dB to +60 dB

 

Max. input level

+12 dBu @ +10 dB GAIN

 

Impedance

approx. 2.6 kΩ balanced

 

Signal-to-noiseratio

110 dB / 112 dB A-weighted

 

 

(0 dBu In @ +22 dB GAIN)

 

Distortion (THD+N)

0.005 % / 0.004 % A-weighted

Line input

 

 

Type

¼" TRS jack, electronically

 

 

balanced

 

Impedance

approx. 20 kΩ balanced, approx.

 

 

10 kΩ unbalanced

 

Gain range

-10dB to +40 dB

 

Max. input level

+22 dBu @ 0 dB GAIN

Fade-outattenuation2(Crosstalk attenuation)

 

Main fader closed

90 dB

 

Channel muted

89.5 dB

 

Channel fader muted

89 dB

Frequency response (Mic In Main Out)

 

 

<10 Hz - 90 kHz

+0 dB / -1dB

 

<10 Hz - 160 kHz

+0 dB / -3dB

Stereo inputs

 

 

Type

¼" TRS jack, electronically

 

 

balanced

 

Impedance

approx. 20 kΩ

 

Max. input level

+22 dBu

Equalizer

EQ mono channels

 

LOW

80 Hz / ±15 dB

 

MID

2.5 kHz / ±15 dB

 

HIGH

12 kHz / ±15 dB

EQ stereo channels

 

 

LOW

80 Hz / ±15 dB

 

MID

2.5 kHz / ±15 dB

 

HIGH

12 kHz / ±15 dB

ENGLISH

ENGLISH

10

Send / Return

Aux sends

 

Type

¼" TS jack, unbalanced

 

Impedance

approx. 120 Ω

 

Max. output level

+22 dBu

Stereo aux returns

 

 

Type

¼" TRS jack, electronically

 

 

balanced

 

Impedance

approx. 20 kΩ balanced / approx.

 

 

10 kΩ unbalanced

 

Max. input level

+22 dBu

Outputs

Main outputs

 

Type

¼" TRS jack, unbalanced

 

Impedance

approx. 120 Ω unbalanced

 

Max. output level

+22 dBu

Control room outputs

 

 

Type

¼" TS jack, unbalanced

 

Impedance

approx. 120 Ω

 

Max. output level

+22 dBu

Headphones output

 

 

Type

¼" TRS jack, unbalanced

 

Max. output level

+19 dBu / 150 Ω (+25 dBm)

Main mix system data3(Noise)

 

 

Main mix @ -∞,channel fader @-∞

-106dB /-109dBA-weighted

 

Main mix @ 0 dB, channel fader @ -∞

-95dB /-98dBA-weighted

 

Main mix @ 0 dB, channel fader @ 0 dB

-84dB /-87dBA-weighted

Power supply

502 / 802 / 1002

 

 

 

 

Power consumption

13 W

 

USA/Canada

 

 

 

Adapter

BEHRINGER PSU MX3UL

 

 

Mains voltage

120 V~, 60 Hz

 

Europe/U.K./Australia

 

 

 

Adapter

BEHRINGER PSU MX3EU

 

 

Mains voltage

230 V~, 50 Hz

 

China

 

 

 

Adapter

BEHRINGER PSU MX3CC

 

 

Input

220 V~ 50 Hz; 80 mA

 

 

Output

2 x 18.5 V~, 2 x 150 mA

 

Korea

 

 

 

Adapter

BEHRINGER PSU MX3KR

 

 

Mains voltage

220 V~, 60 Hz

 

Japan

 

 

 

Adapter

BEHRINGER PSU MX3JP

 

 

Mains voltage

100 V~, 50/60 Hz

 

 

 

 

 

 

XENYX 502/802/1002/1202 User Manual

 

 

 

 

 

 

 

1202

 

 

 

 

 

Power consumption

20 W

 

 

USA/Canada

 

 

 

 

Adapter

BEHRINGER PSU MX5UL

 

 

 

Mains voltage

120 V~, 60 Hz

 

 

Europe/U.K./Australia

 

 

 

 

Adapter

BEHRINGER PSU MX5EU

 

 

 

Mains voltage

230 V~, 50 Hz

 

 

China

 

 

 

 

Adapter

BEHRINGER PSU MX5CC

 

 

 

Input

220 V~ 50 Hz; 150 mA

 

 

 

Output

2 x 17.5 V~, 2 x 650 mA

 

 

Korea

 

 

 

 

Adapter

BEHRINGER PSU MX5KR

 

 

 

Mains voltage

220 V~, 60 Hz

 

 

Japan

 

 

 

 

Adapter

BEHRINGER PSU MX5JP

 

 

 

Mains voltage

100 V~, 50/60 Hz

Physical/weight

 

 

 

 

 

 

502

 

 

 

 

 

 

Dimensions (H x W x D)

1.9" / 1.5" x 5.3" x 7" (47 mm /

 

 

 

 

 

 

37 mm x 134 mm x 177 mm)

 

 

 

Weight (net)

1.2 lbs (0.55 kg)

 

 

 

 

 

802

 

 

 

 

 

 

Dimensions (H x W x D)

1.9" / 1.5" x 7.4" x 8.7" (47 mm /

 

 

 

 

 

 

37 mm x 189 mm x 220 mm)

 

 

 

Weight (net)

2.2 lbs (1.00 kg)

 

 

 

 

1002

 

 

 

 

 

Dimensions (H x W x D)

1.9" / 1.5" x 7.4" x 8.7" (47 mm /

 

 

 

 

 

 

37 mm x 189 mm x 220 mm)

 

 

 

Weight (net)

2.3 lbs (1.05 kg)

 

 

 

 

1202

 

 

 

 

 

Dimensions (H x W x D)

1.9" / 1.5" x 9.5" x 8.7" (47 mm /

 

 

 

 

 

 

37 mm x 242 mm x 220 mm)

 

 

 

Weight (net)

3 lbs (1.35 kg)

1Equivalent Input Noise

2Measuring conditions: 1 kHz rel. to 0 dBu; 20 Hz - 20 kHz; line input; main output; unity gain.

320 Hz - 20 kHz; measured at main output. Channels 1 - 4 unity gain; EQ flat; all channels on main mix; channels 1/3 as far left as possible; channels 2/4 as far right as possible; reference = +6 dBu.

BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated.

XENYX 502/802/1002/1202 User Manual

11

 

Limited Warranty

§ 1 Warranty

[1] This limited warranty is valid only if you purchased the product from a BEHRINGER authorized dealer in the country of purchase. A list of authorized dealers can be found on BEHRINGER’s website www.behringer.com under“Where to Buy”, or you can contact the BEHRINGER o ce closest to you.

[2]BEHRINGER* warrants the mechanical and electronic components of this product to be free of defects in material and workmanship if used under normal operating conditions for a period of one (1) year from the original date of purchase (see the Limited Warranty terms in § 4 below), unless a longer minimum warranty period

is mandated by applicable local laws. If the product shows any defects within the specified warranty period and that defect is not excluded under § 4, BEHRINGER shall, at its discretion, either replace or repair the product using suitable new or reconditioned product or parts. In case BEHRINGER decides to replace the entire

product, this limited warranty shall apply to the replacement product for the remaining initial warranty period, i.e., one (1) year (or otherwise applicable minimum warranty period) from the date of purchase of the original product.

[3]Upon validation of the warranty claim, the repaired or replacement product will be returned to the user freight prepaid by BEHRINGER.

[4]Warranty claims other than those indicated above are expressly excluded.

PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF OF PURCHASE COVERING YOUR LIMITED WARRANTY. THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF OF PURCHASE.

§ 2 Online registration

Please do remember to register your new BEHRINGER equipment right after your purchase at www.behringer.com under“Support” and kindly read the terms and conditions of our limited warranty carefully. Registering your purchase and equipment with us helps us process your repair claims quicker and more e ciently. Thank you for your cooperation!

§ 3 Return authorization number

[1] To obtain warranty service, please contact the retailer from whom the equipment was purchased. Should your BEHRINGER dealer not be located in your vicinity, you may contact the BEHRINGER distributor for your country listed under“Support” at www.behringer.com. If your country is not listed, please check if your problem can

be dealt with by our“Online Support” which may also be found under“Support” at www.behringer.com. Alternatively, please submit an online warranty claim at

www.behringer.com BEFORE returning the product. All inquiries must be accompanied by a description of the problem and the serial number of the product. After verifying the product’s warranty eligibility with the original sales receipt, BEHRINGER will then issue a Return Materials Authorization (“RMA”) number.

[2]Subsequently, the product must be returned in its original shipping carton, together with the return authorization number to the address indicated by BEHRINGER.

[3]Shipments without freight prepaid will not be accepted.

§ 4 Warranty Exclusions

[1] This limited warranty does not cover consumable parts including, but not limited to, fuses and batteries. Where applicable, BEHRINGER warrants the valves or meters contained in the product to be free from defects in material and workmanship for a period of ninety (90) days from date of purchase.

[2]This limited warranty does not cover the product if it has been electronically or mechanically modified in any way. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in materials or workmanship. This limited warranty does not cover any such modification/adaptation, regardless of whether it was carried out properly or not. Under the terms of this limited warranty, BEHRINGER shall not be held responsible for any cost resulting from such a modification/adaptation.

[3]This limited warranty covers only the product hardware. It does not cover technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the product. Any such software is provided“AS IS” unless expressly provided for in any enclosed software limited warranty.

[4]This limited warranty is invalid if the factory-appliedserial number has been altered or removed from the product.

[5]Free inspections and maintenance/repair work are expressly excluded from this limited warranty, in particular, if caused by improper handling of the product by the user. This also applies to defects caused by normal wear and tear, in particular, of faders, crossfaders, potentiometers, keys/buttons, tubes, guitar strings, illuminants and similar parts.

[6]Damage/defects caused by the following conditions are not covered by this limited warranty:

improper handling, neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals;

connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used;

damage/defects caused by acts of God/Nature (accident, fire, flood, etc) or any other condition that is beyond the control of BEHRINGER.

[7]Any repair or opening of the unit carried out by unauthorized personnel

(user included) will void the limited warranty.

[8]If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the limited warranty, the inspection costs are payable by the customer.

[9]Products which do not meet the terms of this limited warranty will be repaired exclusively at the buyer’s expense. BEHRINGER or its authorized service center will inform the buyer of any such circumstance. If the buyer fails to submit a written repair order within 6 weeks after notification, BEHRINGER will return the unit C.O.D. with a separate invoice for freight and packing. Such costs will also be invoiced separately when the buyer has sent in a written repair order.

[10] Authorized BEHRINGER dealers do not sell new products directly in online auctions. Purchases made through an online auction are on a“buyer beware” basis. Online auction confirmations or sales receipts are not accepted for warranty

verification and BEHRINGER will not repair or replace any product purchased through an online auction.

§ 5 Warranty transferability

This limited warranty is extended exclusively to the original buyer (customer of authorized retail dealer) and is not transferable to anyone who may subsequently purchase this product. No other person (retail dealer, etc.) shall be entitled to give any warranty promise on behalf of BEHRINGER.

ENGLISH

ENGLISH

12

XENYX 502/802/1002/1202 User Manual

 

§ 6 Claim for damage

Subject only to the operation of mandatory applicable local laws, BEHRINGER shall have no liability to the buyer under this warranty for any consequential or indirect loss or damage of any kind. In no event shall the liability of BEHRINGER under this limited warranty exceed the invoiced value of the product.

§ 7 Limitation of liability

This limited warranty is the complete and exclusive warranty between you and BEHRINGER. It supersedes all other written or oral communications related to this product. BEHRINGER provides no other warranties for this product.

§ 8 Other warranty rights and national law

[1] This limited warranty does not exclude or limit the buyer’s statutory rights as a consumer in any way.

[2]The limited warranty regulations mentioned herein are applicable unless they constitute an infringement of applicable mandatory local laws.

[3]This warranty does not detract from the seller’s obligations in regard to any lack of conformity of the product and any hidden defect.

§ 9 Amendment

Warranty service conditions are subject to change without notice. For the latest warranty terms and conditions and additional information regarding BEHRINGER’s limited warranty, please see complete details online at www.behringer.com.

* BEHRINGER Macao Commercial Offshore Limited of Rue de Pequim No. 202-A,Macau Finance Centre 9/J, Macau, including all BEHRINGER group companies

Legal Disclaimer

Technical specifications and appearance are subject to change without notice. The information contained herein is correct at the time of printing. BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. Colors and specifications may vary slightly from product. BEHRINGER products are sold through authorized dealers only. Distributors and dealers are not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation. This manual is copyrighted. No part of

this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of Red Chip Company Ltd.

ALL RIGHTS RESERVED. © 2009 Red Chip Company Ltd.

Trident Chambers, Wickhams Cay, P.O. Box 146,

Road Town, Tortola, British Virgin Islands

XENYX 502/802/1002/1202 User Manual

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

 

XENYX 502/802/1002/1202

Responsible party name: BEHRINGER USA, Inc.

Address:

18912 North Creek Parkway,

 

Suite 200 Bothell, WA 98011,

 

USA

Phone/Fax No.:

Phone: +1 425 672 0816

 

Fax: +1 425 673 7647

hereby declares that the product

XENYX 502/802/1002/1202

complies with the FCC rules as mentioned in the following paragraph:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

13

ENGLISH

ENGLISH

This manual is available in English, German, French, Spanish, Italian, Russian, Polish, Dutch, Finnish, Swedish, Danish, Portuguese, Greek, Japanese

and Chinese. There may also be more current versions of this document. Download them by going to the appropriate product page at:

www.behringer.com