B&B Electronics EIR203-3MT User Manual

Size:
420.44 Kb
Download

QUICK START GUIDE

B&B ELECTRONICS

EIR203 Series Quick Start

Guide

Package Contents

EIR203 Series Industrial, Unmanaged, Ethernet Switch

Quick Start Guide (One per shipment)

Power Terminal Block (installed)

Fiber Optic Dust Covers (installed on fiber optic models)

If any item is missing or damaged, contact B&B Electronics for a replacement

EIR203 1308qsg-1/2

© 2008 by B&B Electronics. All rights reserved.

1.Slide and hold the DIN clip toward the bottom of the switch. Angle the top portion of the DIN mount over the top of DIN Rail.

2.Move the switch so that it is parallel with the DIN Rail.

3.Let go of the DIN Clip. The spring should return it to its original position.

Attach Power Leads

External Supply Required

Front Panel

 

 

EIR203 (3 Fiber)

 

 

EIR203 (1 Fiber, 2 RJ-45)

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Power Terminal Block

 

2 Position, Removable

 

2

PWR LED

 

ON When Power Applied

 

3

Fiber Optic SPD LED

 

Normally OFF (100BaseFx)

 

3

Fiber Optic LINK LED

 

ON When Fiber Port Linked

 

4

Fiber Ports

 

Number and type depends on Model

 

5

RJ45 Ports

 

Number depends on model

 

6

RJ45 LINK LED

 

On when RJ45 Port Linked

 

 

 

 

Flashes When Data Transmitted

 

6

RJ45 SPD LED

 

On if 100 mbps

Warning: Work Safe – Equipment damage or electrical shock hazard exists. DO NOT ATTACH OR REMOVE LEADS WITH THE POWER SUPPLY ENERGIZED!

1.Loosen the screw to open the terminal block lead clamp.

2.Insert the power lead. TB will accept 12-28AWG wire.

3.Tighten the screw to close the terminal block lead clamp. Ensure the clamp holds the lead securely. However, do not over tighten.

NOTE: For replacement Terminal Block order Part # 7444.

Attach RJ45 Cable

(If equipped)

DIN Rail Mounting

Female RJ45

1. Auto MDI/MDI-xis supported. A straight through orcross-overcable may be used.

2. 10/100BaseT auto negotiation and full/halfduplex are supported.

MDI Cable Pinout

Pin

Signal

1

Tx+

2

Tx-

3

Rx+

6

Rx-

MDI-XCable Pinout

Pin

Signal

1

Rx+

2

Rx-

3

Tx+

6

Tx-

International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA815-433-5100Fax433-5104www.bb-elec.com orders@bb-elec.com support@bb-elec.com

European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445www.bb-europe.com orders@bb-europe.com support@bb-europe.com

QUICK START GUIDE

B&B ELECTRONICS

 

 

EIR203 1308qsg-2/2

 

 

© 2008 by B&B Electronics. All rights reserved.

 

 

 

 

Attach Fiber Optic Cable

 

Mechanical Diagram

 

(if equipped)

 

 

 

 

 

 

 

 

 

 

Warning: Work Safe – Fiber Optic equipped models are Class I Laser/LED devices. To avoid causing serious damage to your eyes,DO NOT STARE DIRECTLY INTO THE LIGHT.

1.Slider Guide

2.Slider Ridges

3.Slider

1.Ensure your fiber optic cable is terminated with the correct connector type. EIR203 switches use SC or ST connectors.

2.Fiber optic type for each port is located on the product’s side label. When connecting the cable to the switch, be sure to line up the slider guide on the cable and switch connectors.

3.Connect the fiber optic transmitter to the downstream device’s receiver and vice-versa.

Fiber Optic Cable Information

Mode and Distance

Type

Wavelength

Multi-mode(2 km)

62.5/125 µm

1310 nm

Single-mode(15 km)

9/125 µm

1310 nm

Single-mode(40 km)

9/125 µm

1310 nm

Single-mode(80 km)

9/125 µm

1550 nm

 

Output Power

RCVR Sensitivity

Multi-mode(2 km)

-19to-14dBm

-32dBm

Single-mode(15 km)

-15to-8dBm

-32dBm

Single-mode(40 km)

-5to 0 dBm

-34dBm

Single-mode(80 km)

-5to 0 dBm

-34dBm

Installation Complete

1.When the network cables are attached and power is applied, installation is complete.

2.The switch will automatically discover network devices, populate its MAC address table, and pass traffic to the appropriate ports.

International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA815-433-5100Fax433-5104www.bb-elec.com orders@bb-elec.com support@bb-elec.com

European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445www.bb-europe.com orders@bb-europe.com support@bb-europe.com