|
PDS Series |
Barco, Inc. |
+1 (916) 859-2515 |
|
Fax: |
||
|
|
Toll Free: |
+1 (888) 414-7226 |
|
Quick Start Guide |
Technical Support: |
+1 (866) 374-7878 |
|
|||
Visibly yours |
Website: |
www.barco.com |
|
|
|
|
|
|
|
|
|
|
|
|
|
Menu Display
Use ADJUST knob, plus SEL and ESC buttons to navigate menus.
Adjust
•Counter-clockwise: scroll down menu tree, or decrement values.
•Clockwise: scroll up menu tree, or increment values.
SEL
Press to enter a menu, change or accept a parameter, or answer
“Yes” to a query.
Inputs Section |
Button States |
||
Sources 1-4: |
Analog |
Off: |
Input not selected |
Sources 5-8*: |
DVI or Analog |
Blinking: |
Input “pending” for transition |
SDI: |
3G/HD/SD-SDI |
Lit solid: |
Input on Program |
|
|
||
LOGO: |
Full screen capture |
|
|
* (sources 7-8 not on PDS-701)
PROGRAM: |
RGB |
|
1024x768@59.94 |
|
|
NEXT: |
SDI |
|
NTSC (480i) |
|
|
|
|
|
|
Inputs |
|
|
|
SEL |
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
SDI |
Adjust |
ESC |
FRZ |
BLACK |
TAKE |
Effects
PDS-902
LOGO |
ESC |
|
FRZ |
|
BLACK |
|
TAKE |
Press to exit a menu |
|
Press to freeze or |
|
Press to pend or initiate a black transition. |
|
Press to mix the selected input |
without making changes, |
|
un-freeze current |
|
Black Auto Take mode affects function |
|
to Program, or to execute a pending |
cancel an operation, or |
|
Program source. |
|
(User Preferences). Blinking = Pending. |
|
black transition. Use the Setup Menu |
answer “No” to a query. |
|
Lit solid = frozen. |
|
Lit solid = Black on Program. |
|
to adjust the transition time. |
|
|
|
|
|
|
|
NOTE
After each TAKE, Program and pending sources flip-flop.
Quick Setup and Operations
The following list summarizes PDS setup and operations. For error-free installation, always refer to the listed section in the User’s Guide.
Connect Power — Ensure that power is properly 1 connected to the PDS. (Chapter 3, “Cable and
Adapter Information”)
Connect Inputs — Connect all analog, DVI, and 2 SDI input sources to the PDS. (Chapter 3, “Signal
Installation”)
Connect Outputs — Connect the output(s) of the 3 PDS to your projector(s) or other target devices.
(Chapter 3, “Signal Installation”)
Power On — Turn on power to the PDS, your 4 projector(s), and to all peripheral equipment.
(Chapter 4, “Power-Up Initialization”)
Factory Reset – When using a PDS for the first 5 time, perform a factory reset. (Chapter 4,
“Factory Reset Menu”)
Launch GUI — (Optional) Connect your laptop to the 6 PDS, log onto the PDS using its IP address, and
launch the GUI. (Chapter 5, “GUI Operations”)
Set Output Format — Set the desired output 7 resolution and frame rate. (Chapter 4, “Output
Format”)
Enable Test Pattern — Turn on a test pattern, verify 8 an image, and adjust as required. When complete,
turn off the pattern. (Chapter 4, “Test Pattern”)
Save Output Configuration — After completing all
9 output adjustments, save the output configuration. (Chapter 4, “Save Config”)
Select and Adjust Input — Select an input, and
10 perform the necessary image adjustments. (Chapter 4, “Input Menu”)
Save Input Configuration — After completing all
11 adjustments for an input, save the input configuration. (Chapter 4, “Save Config”)
Repeat for Each Input — Repeat steps 10 and
12 11 for each input that you have connected to the PDS.
Adjust System Parameters — Adjust parameters
13 such as transition time, display brightness, user prefs. (Chapter 4, “User Preference Menu,” “System Menu”)
Save System Configuration — After completing all
14 system adjustments, save the system configuration. (Chapter 4, “Save System State”)
Enable Remote Control — (Optional) Connect
15 Ethernet or Serial communications, and issue desired commands. (Appendix B, “Remote Control”)
Ready to Roll — With all output, input and system 16 configurations saved, press the desired input button,
and press TAKE.
P/N 26-1204004-00 Rev 01