Barco MATRIXPRO-II HD-3G SDI User Manual

Size:
239.72 Kb
Download

MatrixPRO-II

HD/3G SDI series

User manual

Rev. 1.1

o Manual #:26-0903001-00o Revision: 01.1

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Copyright

© Barco. March 09, 2011

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Notice

Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/ or the program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.

Federal Communications (FCC) Statement

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of compliant, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

2

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either.

The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufactures.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

3

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Company Address

Barco, Inc.

11101 Trade Center Drive

Rancho Cordova,

California 95670 USA

Phone: (916) 859-2500

Fax: (916) 859-2515

Barco N.V.

Noordlaan 5 8520

Kuurne

BELGIUM

Phone: +32 56.36.82.11

Fax: +32 56.35.16.51

Website: www.barco.com

Technical Support

Customer Service Portal www.barco.com/esupport (866)374-7878— Events (24/7)

(866) 469-8036 — Digital Cinema (24/7)

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

4

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Operators Safety Summary

The general safety information in this summary is for operating personnel.

Do not remove panels or covers

There are no user-serviceableparts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed.

Power Source

This product is intended to operate from a power source that will not apply more than 230 volts rms between the supply conductors or between both supply conductor and ground. A protective ground connection by way of grounding conductor in the power cord is essential for safe operation.

Grounding the Product

This product is grounded through the grounding conductor of the power cord. To avoid electrical shock, plug the power cord into a properly wired receptacle before connecting to the product input or output terminals. A protective-groundconnection by way of the grounding conductor in the power cord is essential for safe operation.

Use of the Power Cord

Use only the power cord and connector specified for your product. Use only a power cord that is in good condition. Refer cord and connector changes to qualified service personnel.

Use of the Proper Fuse

To avoid fire hazard, use only the fuse having identical type, voltage rating, and current rating characteristics. Refer fuse replacement to qualified service personnel.

Do not Operate in Explosive Atmospheres

To avoid explosion, do not operate this product in an explosive atmosphere.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

5

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Terms in This Manual and Equipment Marking

Warning

Highlights an operating procedure, practice, condition, statement, etc., which, if not strictly observed, could result in injury to or death of

personnel.

Highlights an essential operating procedure,

condition or Statement

NOTE

Caution

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVETISSEMENT!

Le point d´exclamation dans un triangle equilatéral signale à alerter l´utilisateur qu´il y a des instructions d´operation et d´entretien tres importantes dans la litérature qui accompagne l´appareil.

VORSICHT

Ein Ausrufungszeichen innerhalb eines gleichwinkeligen Dreiecks dient dazu, den Benutzer auf wichtige Bedienungs-undWartungsanweisungen in der Dem Great beiliegenden Literatur aufmerksam zu machen.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

6

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Change History

 

Date

ECP #

Description

Approved By

0.0

5/20/10

578607

User’s Guide

GKOU

1.1

3/09/11

586286

Added default IP address

GKOU

 

 

 

Added interface commands appendix

 

 

 

 

Added MP-II3G Configuration Tool

 

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

7

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

 

Contents

 

1.1

Product versions.....................................................................................................

10

2

Specifications................................................................................................

11

2.1

Mechanics ................................................................................................................

11

2.1.1

Weight and power consumption ..........................................................................

11

2.2

Power Supply ..........................................................................................................

11

2.3

Control......................................................................................................................

11

2.4

Video specifications................................................................................................

12

2.5

Connection details..................................................................................................

13

2.5.1

Power Supply pinout..............................................................................................

13

3

Configuration................................................................................................

14

3.1

SW1 – SW4: Address/Level Not Used...............................................................

14

3.2

SW5-SW6:Router mode.......................................................................................

14

3.2.1

Router mode on NxN square routers..................................................................

14

3.3

SW7: Power alarm .................................................................................................

18

3.4

SW8: Power-upmode............................................................................................

18

3.5

Switching time ........................................................................................................

19

3.6

Configuring protocol options ................................................................................

19

4

LED status indication ..................................................................................

20

4.1

Start-up....................................................................................................................

20

4.2

Alarm states............................................................................................................

20

4.3

Ethernet states .......................................................................................................

20

5

Router communication................................................................................

21

5.1

Serial connection....................................................................................................

21

5.1.1

Maximum cable length (RS-232).........................................................................

21

5.2

Ethernet connection...............................................................................................

22

6

Control Panel operation..............................................................................

23

6.1

Button description..................................................................................................

23

7

Environmental Specifications ..........................................................................

25

Appendix A..................................................................................................................

26

A.1 Materials declaration......................................................................................................

26

A.2 Recycling information ....................................................................................................

27

A.3 Declarations of Conformity ..................................................................................................

28

Appendix B Remote Commands..............................................................................

29

B.1 X-PointTake .......................................................................................................................

30

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

8

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

B.2

Request X-PointStatus .......................................................................................................

31

B.3

Router Ping .........................................................................................................................

32

B.4

Level List.............................................................................................................................

32

Appendix C Barco MPII-3GConfiguration Tool ....................................................

33

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

9

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Product overview

This User Manual presents the features, installation and operation procedures of (3G/HD/SDSDI) routers of the Barco MatrixPRO-IIseries.

Router models available: 8x8, 16x16 and 32x32

Communication: TCP/IP and RS-232

Programmable multisingleand dual bus control panels

Ultra Slim frame depth

Low Power, high reliability design

Redundant power supply system with front indicators

Future proof and flexible product range

Barco’s MatrixPRO-II3G/HS/SD-SDIseries is ideal for general events, fixed installations, onair routing, mobile outside broadcast applications and sophisticated A/V applications.

1.1Product versions

The following versions of the Barco MatrixPRO-II3G/HD/SD-SDIRouters are available:

1RU, Depth 5cm

 

R9004661

8x8 HD/3G Digital Video Router

 

Multirate: 270Mbps-2.97Gbps

 

Router partitioning.

 

Reclocking.

R9004660

16x16 HD/3G Digital Video Router

 

Multirate: 270Mbps-2.97Gbps

 

Router partitioning.

 

Reclocking.

2RU, depth 5cm:

 

R9004662

32x32 HD/3G Digital Video Router

 

Multirate: 270Mbps-2.97Gbps

 

Router partitioning.

 

Reclocking.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

10

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

2Specifications

2.1Mechanics

Dimensions:

 

-

HxWxD = 44x483x50mm, (19”, 1RU);

 

 

 

 

-

HxWxD = 88x483x50mm, (19”, 2RU);

 

Safety/Emission Standards:

Compliant with CE EN55103-1and 2.

 

 

2.1.1

Weight and power consumption

 

 

 

 

 

Device

 

Weight

Current, +15V

Current, -15V

Power

R9004661

 

 

1.3 kg

900 mA

 

2 mA

14 W

R9004660

 

 

1.4 kg

1273 mA

 

4 mA

19 W

R9004662

 

 

2.2 kg

1302 mA

 

1035 mA

35 W

R9871081

 

 

0.35 kg

N/A (AC Mains)

 

2.2

Power Supply

 

 

 

 

 

 

 

SL-PWR-40

 

40W Power Supply Unit

 

 

 

AC Supply voltage range:

100-240VAC,50-60Hz,

 

 

 

 

 

 

Max 1.6A

 

 

 

 

AC Mains connector:

 

IEC 320.

 

 

 

 

DC output:

 

+15V, max. 2.2A

 

 

 

 

 

 

-15V,max 1.35A

 

 

 

 

 

 

Maximum 43W

 

 

 

DC connector:

 

DB9, female.

 

 

 

Status monitoring:

 

Via LED in front of the router/CP.

 

 

 

Safety standards:

 

Compliant with CE EN60950, UL-1950/CSA22.2.

 

2.3

Control

 

 

 

 

 

 

 

Function

 

 

Description

 

Connector

Serial Port

RS-232

 

 

 

 

1xDB9, female

NCB

 

N/A

 

 

 

 

2x RJ45

 

Ethernet port:

10/100BaseT Ethernet bus for external router

1x RJ45

 

 

 

control.

 

 

 

 

 

 

Synchronization

o Analog Black & Burst, looped. Both PAL and

1xBNC

 

 

 

NTSC supported.

 

 

 

 

 

 

Tri-Level,Looped. For HD signal formats only.

 

 

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

11

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

2.4Video specifications

Supported formats:

 

 

Broadcast:

 

-

270Mbps – 2.97Gbps;

 

 

-

DVB-ASI,SMPTE 259M, SMPTE 292M,

 

 

 

SMPTE 424M;

 

 

-

2K, 2048x1556/23.98 and 24.

Electrical signal inputs:

 

 

Standard:

 

SMPTE 259M / SMPTE 292M / SMPTE 424M.

Data rate:

 

270Mbps – 1.485Gbps / 2.97Gbps.

Connector:

 

75 ohm BNC female.

Impedance:

 

75 ohm nominal.

Return loss:

 

-

> 15dB (5MHz-1.485Ghz);

 

 

-

> 10dB (1.5GHz – 3GHz).

Cable equalization,

 

-

Automatic up to 70m @ 2.97Gbps,

 

 

 

typical Belden 1694A;

 

 

-

Automatic up to 100m @ 1.485Gbps,

 

 

 

typical Belden 1694A.

 

 

-

Automatic up to 300m @ 270Mbps, typical Belden

 

 

 

8281.

Electrical signal outputs:

 

 

Connector:

 

75 ohm BNC female.

Impedance:

 

75 ohm nominal.

Return loss:

 

-

> 15dB (5MHz-1.485Ghz);

 

 

-

> 10dB (1.5GHz – 3GHz).

Signal level:

 

800mVp-p±10%.

Rise/fall time:

 

20% - 80%

 

 

-

SD limit: 0.4ns – 1.5ns, < 0.5ns rise/fall variation;

 

 

-

HD limit: < 270ps, < 100ps rise/fall variation;

 

 

-

3G-HDlimit: < 135ps, < 50ps rise/fall variation;

Amplitude overshoot:

< 10%.

Signal polarity:

 

Non-invertingelectrical with respect to inputs.

Signal transition:

 

 

 

Timing jitter:

 

-

SD: < 0.2 UI

 

 

-

3G-HD /HD: < 1 UI.

Alignment jitter:

 

-

SD: < 0.2 UI

 

 

-

3G-HD /HD: < 0.2 UI.

Reference inputs:

 

 

 

Number of inputs:

1

 

 

Connector:

75 ohm BNC female, loop-thru.

Return loss:

>40dB (100 kHz – 5 MHz);

 

>35dB (5-10MHz).

Signal format:

NTSC or PAL Black&Burst or HD Tri-Levelaccording to SMPTE 274M,

 

SMPTE 276M.

 

Signal level:

Nominal 1.0Vp-p.

 

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

12

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Field selectivity:

Field 1.

 

Timing range:

SD, PAL: withinclock-intervals(27MHz) 565 – 835 line 6

SD, NTSC: within clock-intervals(27MHz) 565 – 835 line 10.

HD Tri-Level:1280x720: withinclock-intervals(148.5MHz) 455 – 780 line 7

HD Tri-Level:1920x1080: withinclock-intervals(148.5MHz) 625 – 1070 line 7.

2.5Connection details

The MatrixPRO-IIrouters have the following service connections on the rear of each product:

SYNC:

Synchronization signal (in). Black burst/composite/tri-levelsync

 

reference input with passive loop-throughfor vertical interval

 

switching.

LOOP:

Synchronization signal (out). Loop-throughof SYNC input.

NCB IN/OUT

N/A.

ETHERNET:

10/100Base-TEthernet bus for external router control.

RS 232:

RS-232for external control protocols.

POWER A:

±15VDC power connector.

POWER B:

±15VDC power connector, redundant supply.

CONFIGURATION:

Configurations switch. See Chapter 3 for further descriptions.

2.5.1 Power Supply pinout

The DB9 power pinout for MatrixPRO-IIrouters is as follows;

Pin #

Description

1

GND

2

Not connected

3

Not connected

4

+15VDC

5

Not connected

6

Not connected

7

Not connected

8

-15VDC

9

Not connected

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

13

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

3Configuration

This chapter provides an overview of the configuration options that are available on the Barco MatrixPRO-II3G/HD/SD-SDIRouters.

3.1SW1 – SW4: Address/Level Not Used

3.2SW5-SW6:Router mode

3.2.1 Router mode on NxN square routers

The nxn square Barco MatrixPRO-IIA/V router allows switching in different modes:

Router layers

8x8 router

16x16 router

32x32 router

1 layer

8x8

16x16

32x32

2 layers

4x4

8x8

16x16

3 layers

N.A.

5x5

10x10

4 layers

2x2

4x4

8x8

Switches 5 - 6 on the configuration switch set the router’s mode. The Router Management System software must be configured according to the mode chosen on the router.

The modes can be switched according to the following pattern:

SW 5

SW 6

Router mode

OFF

OFF

1 router layer

OFF

ON

2 router layers

ON

OFF

3 router layers

ON

ON

4 router layers

Default mode is 1 router layer.

Based on the configuration above, the I/O is connected to the router according to the following scheme, where the physical limitations depend on the type of router that is purchased (8x8, 16x16, 32x32):

1 layer:

I/O is connected according to information on the rear of the router.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

14

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

2 layers, based on an 8x8 router:

Layer 1

Input

Layer 1

Output

1

1

1

1

2

2

2

2

3

3

3

3

4

4

4

4

Layer 2

Input

Layer 2

Output

1

5

1

5

2

6

2

6

3

7

3

7

4

8

4

8

2 layers, based on a 16x16 router:

Layer 1

Input

Layer 1

Output

1

1

1

1

2

2

2

2

3

3

3

3

4

4

4

4

8

8

8

8

Layer 2

Input

Layer 2

Output

1

9

1

9

2

10

2

10

3

11

3

11

4

12

4

12

8

16

8

16

2 layers, based on a 32x32 router:

Layer 1

Input

Layer 1

Output

1

1

1

1

2

2

2

2

3

3

3

3

4

4

4

4

16

16

16

16

Layer 2

Input

Layer 2

Output

1

17

1

17

2

18

2

18

3

19

3

19

4

20

4

20

16

32

16

32

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

15

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

3 layers, based on a 16x16 router:

Layer 1

Input

Layer 1

Output

1

1

1

1

2

2

2

2

3

3

3

3

4

4

4

4

5

5

5

5

Layer 2

Input

Layer 2

Output

1

6

1

6

2

7

2

7

3

8

3

8

4

9

4

9

5

10

5

10

Layer 3

Input

Layer 3

Output

1

11

1

11

2

12

2

12

3

13

3

13

4

14

4

14

5

15

5

15

In-/Output16 is not in use in this router setup (3 router layers, based on a 16x16 router).

3 layers, based on a 32x32 router:

Layer 1

Input

Layer 1

Output

1

1

1

1

2

2

2

2

3

3

3

3

10

10

10

10

Layer 2

Input

Layer 2

Output

1

11

1

11

2

12

2

12

3

13

3

13

10

20

10

20

Layer 3

Input

Layer 3

Output

1

21

1

21

2

22

2

22

3

23

3

23

10

30

10

30

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

16

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

In-/Outputs31 and 32 are not in use in this router setup (3 router layers, based on a 32x32 router).

4 layers, based on an 8x8 router:

 

Layer 1

Input

Layer 1

Output

 

1

1

1

1

 

2

2

2

2

 

Layer 2

Input

Layer 2

Output

 

1

3

1

3

 

2

4

2

4

 

Layer 3

Input

Layer 3

Output

 

1

5

1

5

 

2

6

2

6

 

Layer 4

Input

Layer 4

Output

 

1

7

1

7

 

2

8

2

8

4 layers, based on a 16x16 router:

 

 

 

 

 

 

 

 

Layer 1

Input

Layer 1

Output

 

1

1

1

1

 

2

2

2

2

 

3

3

3

3

 

4

4

4

4

 

Layer 2

Input

Layer 2

Output

 

1

5

1

5

 

2

6

2

6

 

3

7

3

7

 

4

8

4

8

 

Layer 3

Input

Layer 3

Output

 

1

9

1

9

 

2

10

2

10

 

3

11

3

11

 

4

12

4

12

 

Layer 4

Input

Layer 4

Output

 

1

13

1

13

 

2

14

2

14

 

3

15

3

15

 

4

16

4

16

4 layers, based on a 32x32 router:

Layer 1

Input

Layer 1

Output

1

1

1

1

2

2

2

2

8

8

8

8

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

17

MatrixPRO-II3G/HD/SD-SDIRouters

 

 

Rev. 1.1

 

 

 

 

 

 

 

Layer 2

Input

Layer 2

Output

 

 

1

9

1

9

 

 

2

10

2

10

 

 

 

 

8

16

8

16

 

 

Layer 3

Input

Layer 3

Output

 

 

1

17

1

17

 

 

2

18

2

18

 

 

 

 

8

24

8

24

 

 

Layer 4

Input

Layer 4

Output

 

 

1

25

1

25

 

 

2

26

2

26

 

 

 

 

8

32

8

32

 

3.3SW7: Power alarm

The power alarm can be switched according to the following pattern:

SW 7

Power alarm

OFF

Disables Power Alarm

ON

Enables Power Alarm

Default setting is Power Alarm disabled.

Changing this from default setting should only be done when using two (redundant) power supplies.

3.4SW8: Power-upmode

Switch 8 on the configuration switch defines the power up mode on NxN square routers. The MatrixPRO-IIrouter provides two modes for powering up the system.

The power up options can be switched according to the following pattern:

SW 8

Power Up mode

OFF

Switches all outputs according to the buffered information in the

 

routers processor system.

ON

Switches all outputs to input 1.

Default setting switches all outputs according to the buffered information in the routers processor system.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

18

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

3.5Switching time

Switching is performed according to the detected sync reference signal. Switching time is determined by the synchronization signal that feeds the router. This is useful when the video signal has the same format as the synchronization signal. Supported formats are: PAL, NTSC, 750/50p, 750/60p, 1125/50i and 1125/60i.

3.6Configuring protocol options

TCP/IP

This is the default option for the BarcoMatrixPRO-IIHD/3G SDI routers. Selecting this protocoldisables the RS-232 port of that device.

RS232

The serial protocol can be selected from the configurator software. Selecting the RS232 protocol disables the Ethernet port of that device.

Default IP Address: 192.168.0.245 - Port: 4381

RS-232parameters:

-Bit rate: 19200 bit/s

-Data bits: 8

-Stop bits: 1

-Parity: no parity

Connection to the router will be lost after 20 seconds of inactivity

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

19

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

4LED status indication

4.1Start-up

The LED located at the front of the router indicates the status of the router. At start-up,the LED will alternate between red (R) and green (G) every 500ms for about two seconds. After thestart-upsequence the LED will indicate the Alarm state of the router.

There are two LEDs located at the Ethernet bus. At start-upthe boot loader is searching for update commands on the serial port for about two seconds. During this sequence both Ethernet LEDs will be blinking. After thestart-upsequence the LEDs will indicate the Ethernet state.

4.2Alarm states

The LED can either be red (R), green (G), yellow (Y) or have no light (N).

The LED state is here described with twenty letters, each representing 100ms, which totals to an alarm sequence of two seconds. The X indicates that the LED keeps the color it has the moment the alarm sequence begins (green, yellow or no light).

Description

LED state

Alarm

Comment

Continuous

GGGGG GGGGG GGGGG GGGGG

No alarm. Status

 

green light

 

is OK.

 

Continuous

YYYYY YYYYY YYYYY YYYYY

Unable to

This alarm will be

yellow light

 

connect to

overwritten by

 

 

controller over

other alarms

 

 

Ethernet.

 

Long red

RRRRR NNNNN RRRRR NNNNN

Power is too low.

 

blinks

 

 

 

One short

RXXXX XXXXX XXXXX XXXXX

Power A failed

Only active if

red blink

 

 

power alarm dip is

 

 

 

set.

Two short

XXXXX XXXXX RXRXX XXXXX

Power B failed

Only active if

red blinks

 

 

power alarm dip is

 

 

 

set.

4.3Ethernet states

The LEDs that are located at the Ethernet bus will after the Start-upsequence indicate the Ethernet states:

 

On

Off / Blinking

Green

Valid link

No link

Yellow

No data

Data is transmitted or

 

 

received

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

20

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

5Router communication

You gain access to router for communication purposes by connecting either the router’s serial port to your computer or by using an Ethernet connection.

Do not use both the router’s Ethernet port and RS-232serial port at the same time. Doing so may cause loss of important communication and control data.

5.1Serial connection

Connection can by be made through the serial port(s) of the router;

The communication parameters are configurable. Please refer to the protocol documentation of the appropriate communication/control protocol.

Example: The protocol parameters s are as follows:

Bit rate 19200 bit/s

Data bits 8 bits

Stop bits 1

Parity: No parity

The DB9 female connector for the serial port(s) of the router has the following pin-out:

Pin #

RS-232mode

1

Not in use

2

Tx

3

Rx

4

Not in use

5

GND

6

GND

7

RTS

8

CTS

9

Do Not Connect!

Note that if the standard RS-232cable specification (DCE) is followed:

A cable with Male+Male or Female+Female connectors at the cable ends is used for Rx/Tx crossed connection, and

A cable with Male+Female connectors at the cable ends is used for a straight through connection.

5.1.1 Maximum cable length (RS-232)

IEEE has specified the maximum cable length for an RS-232connection to 15m. Longer distances can be installed depending on the environmental conditions of the installation site.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

21

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

5.2Ethernet connection

The connections follow the standard set by the IEEE 802.3 100BaseTX specification. The cables that are to be applied should be CAT-5 /CAT-5Estandard, or better. It is the responsibility of the installer / user to secure a proper installation of the Ethernet connection.

All Barco MatrixPRO-IIrouters andIP-basedControl Panels are connected together through an Ethernet Switch.

A Barco MatrixPRO-IIdevice has only one physical Ethernet connection. If redundant control is required, this limitation has to be solved by the control system.

The default IP address is: 192.168.0.245 port: 4381

Connection to the router will be lost after 20 seconds of inactivity

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

22

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

6Control Panel operation

6.1 Button description A/V Toggle

The A/V Toggle button enables/disables audio and video on a specified address. The address can either be read from the dip switches, or be fixed. The button toggles between three states.

If the button is pressed for more than 1 second, it will go into a fourth state where both audio and video are disabled.

In this state the button will be dimmed. If the button is pressed for more than 1 second again, it will enable both audio and video if present.

Button Color

Video Enabled

Audio Enabled

Yellow

Yes

Yes

Green

Yes

No

Red

No

Yes

Dimmed

No

No

If neither audio nor video is present, it will be marked as disabled and the toggle state will not be used.

Toggle status changes will be stored in flash and used when the panel is powered up later.

When a panel is powered on it will search for connected routers. If no routers are found the A/V Toggle button will be disabled (no light in the button).

This can happen if the panel is powered up before any routers are connected or if there is something wrong with the cabling.

To re-enablethe A/V Toggle do the following:

1.Activate the Panel Enable button (Green light).

2.Push & Hold the A/V Toggle-buttonfor 2 seconds.

The A/V Toggle-buttonshould now be activated and the light turned on.

Panel Enable

If a Panel Enable button is present, the panel will start up not enabled. In this state the button will be red and all the other buttons will be disabled. When pressing the button the panel will be enabled and the color will change to green. A status request will also be sent to get information on active levels.

If no Panel Enable button is present, the panel will start up enabled.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

23

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Take on/off

The Take on/off button enables or disables the Take button. If no take button is defined, Take on/off is always off. On first start-upthe take button is enabled. Later it will read the last status from the flash memory.

Take

The Take buttons LED is normally off. If the Take on/off button is set to “on”, no commands will be sent from the panel until the Take button is pressed. The last selected buttons and the take button will blink, until the Take button is pressed and the command is sent from the panel.

Output

An Output button is used for selecting an output. Selecting an output activates it, so that it is switched to the next input that is selected.

Input

An Input button switches the active output to the selected input. If the Take button is enabled, the switch will not be executed until the Take button is pressed.

When switching using the Input button, all enabled audioand video-levelswill be switched from the selected input to the active output.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

24

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

7 Environmental Specifications

1.The equipment will meet the guaranteed performance specification under the following environmental conditions:

- Operating room temperature

0°C to 45°C

range:

 

-Operating relative humidity range: <95% (non-condensing)

2.The equipment will operate without damage under the following environmental

 

conditions:

 

-

Temperature range:

-10°Cto 55°C

-

Relative humidity range:

<95% (non-condensing)

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

25

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Appendix A

A.1 Materials declaration

For product sold into China after 1st March 2007, we comply with the “Administrative Measure on the Control of Pollution by Electronic Information Products”. In the first stage of this legislation, content of six hazardous materials has to be declared. The table below shows the required information.

 

 

Toxic or hazardous substances and elements

 

 

 

 

 

 

 

 

 

 

 

 

 

Part

Lead

Mercury

Cadmium

Hexavalent

Polybrominated

Polybrominated

Name

(Pb)

(Hg)

(Cd)

Chromium

biphenyls

diphenyl ethers

 

 

 

 

(Cr(VI))

(PBB)

(PBDE)

 

 

 

 

 

 

 

All

 

 

 

 

 

 

products

 

 

 

 

 

 

referred

O

O

O

O

O

O

to in

 

 

 

 

 

 

Chapter

 

 

 

 

 

 

1.1

 

 

 

 

 

 

SL-

 

 

 

 

 

 

PWR-40

 

 

 

 

 

 

/

O

O

O

O

O

O

SL-

 

 

 

 

 

 

PWR-90

 

 

 

 

 

 

O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T113632006.

X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006.

Parts without any of the above mentioned hazardous substances are indicated by the product marking:

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

26

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

A.2 Recycling information

Please contact Barco’s Customer Support for assistance with recycling if this site does not show the information you require.

Where it is not possible to return the product to Barco or its agents for recycling, the following general information may be of assistance:

Before attempting disassembly, ensure the product is completely disconnected from power and signal connections.

All major parts are marked or labeled to show their material content.

Depending on the date of manufacture, this product may contain lead in solder.

Some circuit boards may contain battery-backedmemory devices.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

27

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

A.3 Declarations of Conformity

DESCRIPTION

3G/HD/SD-SDIVideo Routers in the Barco

 

MatrixPRO-IIseries

DIRECTIVES this equipment

LVD 73/23/EEC

complies with

EMC 2004/108/EEC

HARMONISED STANDARDS applied

EN 55103-1:1996

in order to verify compliance with

EN 55103-2:1996

Directive(s)

 

 

 

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

28

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Appendix B Remote Commands

 

 

 

 

 

 

 

Description

 

 

 

 

 

 

x

X-pointTake.

 

 

 

 

 

 

ls

Status X-point– level.

 

 

 

 

 

 

ping

Router ping.

 

 

 

 

 

 

llist

Level list

 

 

 

 

 

Default Address: 192.168.0.245 port: 4381

Connection to the router will be lost after 20 seconds

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

29

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

B.1 X-PointTake

This command directly takes the specified X-point.The command specifies which sources to connect to which destinations and on what levels. SeveralX-pointtakes can be specified on a single command line. In such cases all specifiedX-pointsare taken simultaneously.

Command:

x<X-points>[ :<group_no>][*CC]<LF> <LF>

Response:

%<LF>

xl<level> <src> <dest><LF> [*CC<LF>]

<LF>

Where:

<X-points>=<X-point>[<X-points>]<X-point>=l<levels><src_dest_pairs> <src_dest_pairs>=<src_dest_pair>[ <src_dest_pairs>] <src_dest_pair>=<src> <dests><levels>={<level>|<levels>,<levels>|<level>-<level>}<dests>={<dest>|<dests>,<dests>|<dest>-<dest>}

<level>

The level number.

<src>

Source number in the range from zero to one less than the number of inputs

 

on the level. <src> can also be one of the following characters:

 

d

Disconnect. Used when a destination is not connected to any source.

 

o

Out of range. Used when a destination is connected to a source not

 

 

included in a level. This may occur with overlapping partitions. Only

 

 

valid in the response.

 

u

Undefined/Unknown. This might be used at start-upbefore the status

 

 

is read from the physical router. It is also used on ported routers

 

 

where a port can be used as an input or an output. Only valid in the

 

 

response.

<dest>

Destination number in the range from zero to one less than the number of

 

outputs on the level.

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

30

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

A single X-pointTake command can switch multipleX-points.You will however receive one response for eachX-pointthat is switched.

Example:

Command

Echo

Desired action

X l1 1 12

X l1 1 12

Switch input 1 to output 12 in level 1

B.2 Request X-PointStatus

This command is used to requests the X-pointstatus of all destinations on a specified level.

Command:

s l<level1> [*CC]<LF><LF>

Response:

%<LF>

x l<level> <src> <dest><LF>

[x l<level> <src> <dest><LF> …]

[*CC<LF>]

<LF>

Example:

Command

Echo

Desired action

s l1

X l1 15 0

Report x-pointstatus in level 1

 

X l1 15 1

 

 

X l1 15 2

 

 

X l1 15 3

 

 

X l1 15 4

 

 

X l1 15 5

 

 

X l1 15 6

 

 

X l1 15 7

 

 

X l1 15 8

 

 

X l1 15 9

 

 

X l1 15 10

 

 

X l1 15 11

 

 

X l1 15 12

 

 

X l1 15 13

 

 

X l1 15 14

 

 

X l1 15 15

 

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

31

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

B.3 Router Ping

This command is used to check if the router is still responding.

Command:

ping[*CC]<LF><LF>

Response:

? "ping"<LF> pong<LF> [*CC<LF>] <LF>

Example:

Command

Echo

Desired action

ping

pong

 

B.4 Level List

This command is used to the get list of all levels in the system.

Command: llist <LF><LF>Response:

? "llist" <LF>

l<level> <size> <format> "<description>"<LF>

[l<level> …] [*CC<LF>] <LF>

Example:

Command

Echo

Desired action

llist

L1 16x16 Video-3GHD-SDI“Video Level”

Provide the list in level 1

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

32

MatrixPRO-II3G/HD/SD-SDIRouters

Rev. 1.1

Appendix C Barco MPII-3GConfiguration Tool

The Barco MPII-3GTool is a software utility that allows the user to:

Read the IP settings

Modify and Save IP settings

Switching the communication between Ethernet and the serial RS-232protocols

MatrixPRO-IIHD/3G SDI Series–User’sGuide - Rev. 1.1

33