Barco iQ Pro G500 User Manual

Size:
11.32 Mb
Download

iQ PRO G500

Owner’s Manual

R9003081

R5976491/09

01/02/2007

Product revision

Software version: projector firmware V3.10

Software version: Server version 1.20

Software version: Client version 1.20

Barco nv Presentations Noordlaan 5, 8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.35.86.51

E-mail:presentations.bid@barco.com Visit us at the web: www.barco.com

Printed in Belgium

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference.

End User License agreement (EULA)

You have acquired a device that includes software licensed by Barco from Microsoft Licensing Inc. or its affiliates (“MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“SOFTWARE”) are protected by international intellectual property laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved.

IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT (“EULA”), DO NOT USE THE DEVICE OR COPY THE SOFTWARE. INSTEAD, PROMPTLY CONTACT BARCO FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE(S) FOR A REFUND.

ANY USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT).

This EULA grants you the following license:

You may use the SOFTWARE only on the DEVICE

NOT FAULT TOLERANT: THE SOFTWARE IS NOT FAULT TOLERANT. BARCO HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE, AND MS HAS RELIED UPON BARCO TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE

NO WARRANTIES FOR THE SOFTWARE: THE SOFTWARE is provided “AS IS” and with all faults. THE ENTIRE RISK AS TO SATISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND EFFORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU. ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE, THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, MS.

No Liability for Certain Damages: EXCEPT AS PROHIBITED BY LAW, MS AND BARCO SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT MS AND BARCO SHALL BE LIABLE FOR ANY AMOUNT IN EXCESS OF U.S. TWO HUNDRED FIFTY DOLLARS (U.S.$250.00).

Limitations on Reverse Engineering, Decompilation, and Disassembly: You may not reverse engineer, decompile, or disassemble the SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.

SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS: You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the Device, and only if the recipient agrees to this EULA. If the SOFTWARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE.

EXPORT RESTRICTIONS: You acknowledge that SOFTWARE is ofUS-origin.You agree to comply with all applicable international and national laws that apply to the SOFTWARE, including the U.S. Export Administration Regulations, as well asend-user,end-useand country destination restrictions issued by U.S. and other governments. For additional information on exporting the SOFTWARE, see http://www.microsoft.com/exporting/.

Installation and Use: The SOFTWARE may not be used by more than two (2) processors at any one time on the DEVICE. You may permit a maximum of ten (10) computers or other electronic devices (each a “Client”) to connect to the DEVICE to utilize the services of the SOFTWARE solely for file and print services, internet information services, and remote access (including connection sharing and telephony services). The ten (10) connection maximum includes any indirect connections made through “multiplexing” or other software or hardware which pools or aggregates connections. Except as otherwise permitted in the NetMeeting/Remote Assistance/Remote Desktop Features terms below, you may not use a Client to use, access, display or run the SOFTWARE, the SOFTWARE’s user interface or other executable software residing on the DEVICE.

If you use the DEVICE to access or utilize the services or functionality of Microsoft Windows Server products (such as Microsoft Windows NT Server 4.0 (all editions) or Microsoft Windows 2000 Server (all editions)), or use the DEVICE to permit workstation or computing devices to access or utilize the services or functionality of Microsoft Windows Server products, you may be required to obtain a Client Access License for the Device and/or each such workstation or computing device. Please refer to the end user license agreement for your Microsoft Windows Server product for additional information.

Restricted Uses: The SOFTWARE is not designed or intended for use or resale in hazardous environments requiringfail-safeperformance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, or other devices or systems in which a malfunction of the SOFTWARE would result in foreseeable risk of injury or death to the operator of the device or system, or to others.

Restricted Functionality: You are licensed to use the SOFTWARE to provide only the limited functionality (specific tasks or processes) for which the DEVICE has been designed and marketed by BARCO. This license specifically prohibits any other use of the software programs or functions, or inclusion of additional software programs or functions, on the DEVICE.

Security Updates: Content providers are using the digital rights management technology (“Microsoft DRM”) contained in this SOFTWARE to protect the integrity of their content (“Secure Content”) so that their intellectual property, including copyright, in such content is not misappropriated. Owners of such Secure Content (“Secure Content Owners”) may, from time to time, request MS, Microsoft Corporation or their subsidiaries to provide security related updates to the Microsoft DRM components of the SOFTWARE (“Security Updates”) that may affect your ability to copy, display and/or play Secure Content through Microsoft software or third party applications that utilize Microsoft DRM. You therefore agree that, if you elect to download a license from the Internet which enables your use of Secure Content, MS, Microsoft Corporation or their subsidiaries may, in conjunction with such license, also download onto your DEVICE such Security Updates that a Secure Content Owner has requested that MS, Microsoft Corporation or their subsidiaries distribute. MS, Microsoft Corporation or their subsidiaries will not retrieve any personally identifiable information, or any other information, from your DEVICE by downloading such Security Updates

NetMeeting/Remote Assistance/Remote Desktop Features: The SOFTWARE may contain NetMeeting, Remote Assistance, and Remote Desktop technologies that enable the SOFTWARE or other applications installed on the Device to be used remotely between two or more computing devices, even if the SOFTWARE or application is installed on only one Device. You may use NetMeeting, Remote Assistance, and Remote Desktop with all Microsoft products; provided however, use of these technologies with certain Microsoft products may require an additional license. For both Microsoft products and non-Microsoft products, you should consult the license agreement accompanying the applicable product or contact the applicable licensor to determine whether use of NetMeeting, Remote Assistance, or Remote Desktop is permitted without an additional license

Consent to Use of Data: You agree that MS, Microsoft Corporation and their affiliates may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE. MS, Microsoft Corporation and their affiliates may use this information solely to improve their products or to provide customized services or technologies to you. MS, Microsoft Corporation and their affiliates may disclose this information to others, but not in a form that personally identifies you

Internet Gaming/Update Features: If the SOFTWARE provides, and you choose to utilize, the Internet gaming or update features within the SOFTWARE, it is necessary to use certain computer system, hardware, and software information to implement the features. By using these features, you explicitly authorize MS, Microsoft Corporation and/or their designated agent to use this information solely to improve their products or to provide customized services or technologies to you. MS or Microsoft Corporation may disclose this information to others, but not in a form that personally identifies you.

Internet-Based Services Components: The SOFTWARE may contain components that enable and facilitate the use of certainInternet-basedservices. You acknowledge and agree that MS, Microsoft Corporation or their affiliates may automatically check the version of the SOFTWARE and/or its components that you are utilizing and may provide upgrades or supplements to the SOFTWARE that may be automatically downloaded to your Device.

Links to Third Party Sites: The SOFTWARE may provide you with the ability to link to third party sites through the use of the SOFTWARE. The third party sites are not under the control of MS, Microsoft Corporation or their affiliates. Neither MS nor Microsoft Corporation nor their affiliates are responsible for (i) the contents of any third party sites, any links contained in third party sites, or any changes or updates to third party sites, or (ii) webcasting or any other form of transmission received from any third party sites. If the SOFTWARE provides links to third party sites, those links are provided to you only as a convenience, and the inclusion of any link does not imply an endorsement of the third party site by MS, Microsoft Corporation or their affiliates.

Additional Software/Services: The SOFTWARE may permit BARCO, MS, Microsoft Corporation or their affiliates to provide or make available to you SOFTWARE updates, supplements,add-oncomponents, orInternet-basedservices components of the SOFTWARE after the date you obtain your initial copy of the SOFTWARE (“Supplemental Components”). If BARCO provides or makes available to you Supplemental Components and no other EULA terms are provided along with the Supplemental Components, then the terms of this EULA shall apply. If MS, Microsoft Corporation or their affiliates make available Supplemental Components, and no other EULA terms are provided, then the terms of this EULA shall apply, except that the MS, Microsoft Corporation or affiliate entity providing the Supplemental Component(s) shall be the licensor of the Supplemental Component(s). BARCO, MS, Microsoft Corporation and their affiliates reserve the right to discontinue anyInternet-basedservices provided to you or made available to you through the use of the SOFTWARE. This EULA does not grant you any rights to use the Windows Media Format Software Development Kit (“WMFSDK”) components contained in the SOFTWARE to develop a software application that uses Windows Media technology. If you wish to use the WMFSDK to develop such an application, visit http://msdn.microsoft.com/workshop/imedia/windowsmedia/sdk/wmsdk.asp, accept a separate license for the WMFSDK, download the appropriate WMFSDK, and install it on your system.

PATENT INFRINGEMENTS: Barco disclaims any warranty that its Products do not infringe any patent, copyright or trademark; but agrees to indemnify you regarding such claims if you promptly notify BARCO in writing and if Barco shall have sole control of the defense of the action and its settlement or compromise. If the use of a Product is enjoined, or a settlement prevents continued use of the Product, Barco shall have the option to procure for you the right to continue use, or replace or modify the Product to remove the infringement. Barco shall have no liability or duty to indemnify you if the infringement or claim is based on use of the Product in combination with other products or software not furnished by Barco, where such claim would not have arisen if such Product were used independently. You will hold Barco harmless against any expense or loss resulting from any infringement caused by compliance with your designs, specifications, or instructions. The foregoing paragraph states Barco’s entire liability with regard to infringement of patents, copyrights, or trademarks. This warranty on IP infringement only is valid within US, Canada, EC, Austria, Norway and Japan.

Copyright ©

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufactures.

Table of contents

TABLE OF CONTENTS

1. Packaging and Dimensions ......................................................................................5

1.1 Box content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .5

1.2 Projector Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .5

1.3 Lens Packaging. . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

1.4 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .6

2. Installation Guidelines.............................................................................................9

2.1 Safety warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .9 2.2 Installation guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .9 2.3 Projector configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .10 2.4 Lenses .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 2.4.1 Lenses. . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 2.4.2 Lens formulas . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.4.3 Lens installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.4.4 Removing the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..16 2.4.5 Cleaning the lens . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 2.5 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .17 2.5.1 Battery installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .17

3. Connections........................................................................................................19

3.1 Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 3.2 Input source connection . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 3.2.1 Input section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 3.2.2 Input facilities. . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 3.2.3 5-Cable input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .21 3.2.4 Composite Video Input. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 3.2.5 S-Video input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .23 3.2.6 Digital Visual Interface (DVI) input . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

3.2.7Computer input.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

3.2.8 Communications Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 3.2.8.1 RS232 IN connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 3.2.9 Extended configuration . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 3.2.9.1 Introduction . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 3.2.9.2 5 cable extended configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 3.2.9.3 S-Video extended configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 3.2.9.4 Summarizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

4. Getting started .....................................................................................................29

4.1 RCU & Local keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .29 4.2 Terminology overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .31 4.3 Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .32 4.4 Lamp runtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .33 4.5 Lamp error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .34 4.6 Quick set up adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .35

4.6.1 Quick lens Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..35 4.6.2 Using the RCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..35 4.7 Projector address .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 4.7.1 Address setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .37 4.7.2 Displaying and Programming addresses into the RCU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 4.8 Controlling the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .38 4.9 Digital Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .39 4.10 Menu structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .39 4.11 Using the menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .39 4.12 Using the Dialogboxes . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

5. Source Selection ..................................................................................................43

5.1 Source selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .43

5.2 Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .44

5.3 S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .45

5.4 The Video Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .46

6. General Menu ......................................................................................................49

6.1 Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .49

6.2 Freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .49

6.3 Standby Timer . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

6.4 Audio (Optional) . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

6.4.1 Audio Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .51

6.4.2 Audio Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .52

6.5 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . .53

7. Image Menu ........................................................................................................55

7.1 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .55

7.1.1 Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .56

R5976491 IQ PRO G500 01/02/2007

 

1

Table of contents

7.1.2 Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .56 7.1.3 Color. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .56 7.1.4 Tint (hue) . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 7.1.5 Sharpness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .57 7.1.6 Gamma. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .57 7.1.7 Phase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .58 7.1.8 Noise reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

7.2 Aspect ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .58 7.3 Show native resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .62 7.4 Keystone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .63 7.5 Color temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .64 7.6 Filmmode detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .65 7.7 Blanking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .67 7.8 Input balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .67 7.9 AGC on Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .72 7.10 Manual Gain Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .73

8. Tools Menu .........................................................................................................75

8.1 Introduction to PiP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 8.2 PiP select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .77 8.3 PiP add window. . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 8.4 PiP remove window . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 8.5 PiP layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .79

8.5.1 PiP Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .79 8.5.2 PiP rename layout .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 8.5.3 PiP delete layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .80 8.6 PiP Adjust. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .81 8.7 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

9. Signal Menu ........................................................................................................85

9.1 Switching mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .85

9.2 Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

10. Lamp Menu .........................................................................................................87

10.1 Runtimes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .87 10.2 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .87 10.3 Power mode (only active in the iQG/R 500) . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 10.4 History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . .90 10.5 Reset runtime. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .91 10.6 Runtime warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .92

11. Image files menu ..................................................................................................95

11.1 Load file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 11.2 Auto Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .96 11.3 Edit file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . .97 11.4 Rename file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .100 11.5 Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .101 11.6 Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .102 11.7 Forced file load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .103

12. Display setup.....................................................................................................105

12.1 Full screen representation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .105 12.2 Startup screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .105 12.3 Textbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .106 12.4 Take screenshot . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 12.5 Menu bar position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .108 12.6 Status bar position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .108 12.7 Sliderbox position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .109 12.8 AutoImage Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .110 12.9 Blanking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .111

13. Installation menu ................................................................................................113

13.1 Lens adjustments .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 13.2 Projector address .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 13.3 Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .115 13.4 Language . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116 13.5 Quick access keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .117 13.6 RS232 baudrate . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 13.7 Automatic startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .118 13.8 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .119 13.9 Change password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .121 13.10 Gemini installed (only for GEMINI CADWALL systems ! ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

14. IQ Network .......................................................................................................123

14.1 Network architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .123 14.2 Network functionality .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 14.3 iQ Pro Server specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .125

2

 

R5976491 IQ PRO G500 01/02/2007

 

Table of contents

14.4 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .125 14.4.1 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 14.4.2 Installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .127 14.4.3 Start up of the iQ Pro Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 14.4.4 Configuring the client software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..129 14.4.5 Configuring the Server software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132

14.5 Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .137 14.5.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .137 14.5.2 How to use the control manager? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 14.5.3 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .138 14.5.4 The source selection screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139 14.5.5 The PiP screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..139 14.5.6 Image settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .142 14.5.7 Advanced control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .144

14.5.7.1 Lens adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 14.5.7.2 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 14.6 Management & diagnostics . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 14.6.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .147 14.6.2 Diagnostics manager . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147

14.7 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .148 14.7.1 E-mail messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .148 14.7.2 E-mail configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .148 14.7.3 Projector Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149 14.8 DropZone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .151 14.8.1 Dropzone tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .151 14.8.2 Start up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .151 14.8.3 File dropping/launching . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153 14.8.4 Open remotely a file on the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155 14.8.5 Remote desktop sharing (virtual meeting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155 14.8.6 DropZone settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .158 14.9 The Web client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .159

15. General guidelines on Network Configuration .............................................................161

15.1 General Network .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161 15.2 The Internet and Web services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .161

A. Exchange...........................................................................................................163

A.1 Exchange Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .163 A.1.1 Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .163 A.1.2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164 A.2 Exchange Integration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .165 A.2.1 Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 A.2.2 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .167 A.2.3 Microsoft Outlook Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..167 A.2.4 Folder form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .169 A.2.5 Limitations and known “problems”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170

B. SNMP services ....................................................................................................171

B.1 SNMP installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .171 B.2 SNMP integration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .171

C. Troubleshooting ..................................................................................................173

C.1 FAQ table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .173

D. Cleaning the dustfilters..........................................................................................175

D.1 Dustfilters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .175 D.2 Cleaning . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175

E. Standard Image Files.............................................................................................177

E.1 Table overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .177

Glossary ...............................................................................................................183

Index....................................................................................................................185

R5976491 IQ PRO G500 01/02/2007

 

3

Table of contents

4

 

R5976491 IQ PRO G500 01/02/2007

1. Packaging and Dimensions

1. PACKAGING AND DIMENSIONS

Overview

Box content

Projector Packaging

Lens Packaging

Dimensions

1.1Box content

CEE7

European power plug to connect the power cord to the wall outlet.

ANSI 73.11

American power plug to connect the power cord to the wall outlet.

Content

1 projector (weight ± 12,6 kg or 27.8 lbs)

1 remote control unit RCU + 2 batteries.

2 power cables with outlet plug type CEE7 and ANSI 73.11.

1 owners manual

1 safety manual

1.2Projector Packaging

Way of Packaging

The projector is packed in a carton box. To provide protection during transportation, the projector is surrounded with foam. The package is secured with banding and fastening clips.

To unpack

1.Release the fastening clips. (image 1-1)

2.Remove the banding. Handle as shown in the drawing.

3.Take the projector out of its shipping carton and place it on a table. (image 1-2)

R5976491 IQ PRO G500 01/02/2007

 

5

1. Packaging and Dimensions

PULL

TO OPE

Image 1-1

R824561

R824562

Projector

R824518 (+ cable basket R724408

R825784

Image 1-2

Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory.

Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory.

CAUTION: Never transport the projector with the lens mounted on it !

Always remove the lens before transporting the projector.

1.3Lens Packaging

Way of Packaging

Lenses are supplied as an individual item.

They are packed in a carton box.

Save the original shipping carton and packing material, they will be necessary if you ever have to transport the lens.

CAUTION: Never transport the projector with the lens mounted on it !

Always remove the lens before transporting the projector.

1.4Dimensions

Dimensions overview

Dimensions are given in mm (1 inch = 25.4 mm)

6

 

R5976491 IQ PRO G500 01/02/2007

1. Packaging and Dimensions

 

487

 

45

 

78

281

305

152

380

Length with different lenses, see table

20 69

Cold air in

415

Hot air out

565

Image 1-3

195

R5976491 IQ PRO G500 01/02/2007

 

7

1. Packaging and Dimensions

Lens

length of projector

combinable with cable

Remarks

 

 

basket

 

 

 

 

 

SVD(2-2.5:1)

545mm

YES

Length with cable basket = 565mm

 

 

 

 

QVD(1.3-1.8:1)

600mm

YES

 

 

 

 

 

QVD(1.9-2.6:1)

590mm

YES

 

 

 

 

 

QVD(3.0-6.0:1)

620mm

YES

 

 

 

 

 

QVD(0.85:1)

545mm

NO

 

 

 

 

 

QVD(7.0:1)

540mm

YES

Length with cable basket = 560mm

 

 

 

 

8

 

R5976491 IQ PRO G500 01/02/2007

2. Installation Guidelines

2. INSTALLATION GUIDELINES

Overview

Safety warnings

Installation guidelines

Projector configurations

Lenses

Batteries

2.1Safety warnings

WARNING: Before installing the projector, read first the safety instructions in the safety manual (R5975258) delivered with the projector.

Insure that the projector is installed in an easy to evacuate room in case of a lamp explosion.

Mercury Vapor Warnings

Keep the following warnings in mind when using the projector. The lamp used in the projector contains mercury. In case of a lamp rupture, explosion there will be a mercury vapor emission. In order to minimize the potential risk of inhaling mercury vapors:

Ensure the projector is installed only in ventilated rooms.

Replace the lamp module before the end of its operational life.

Promptly ventilate the room after a lamp rupture, explosion has occurred, evacuate the room (particularly in case of a pregnant woman).

Seek medical attention if unusual health conditions occur after a lamp rupture, explosion, such as headache, fatigue, shortness of breath, chest-tighteningcoughing or nausea.

2.2Installation guidelines

Ambient temperature check

Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system.

Max. ambient temperature : 40 °C or 104 °F

Min. ambient temperature : 0 °C or 32 °F

The projector will not operate if ambient air temperature falls outside this range (0°C- 40°C or 32°F-104°F).

Environment

Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not excessive

CAUTION: Harmful Environmental Contamination Precaution

Environment condition check

A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets as well as free flow at the ventilation outlets. The installation must also allow easy access to the consumable parts ( dustfilters, lamps, ...) For installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a feasible solution then measures to relocate the projector to a clean air environment should be considered. Make sure that the projector never runs with dirty dustfilters as this will dramatically reduce the lifetime of the consumables. It is advised to clean the dustfilters on a regular basis and to replace them at any lamp change. Barco reserves itself the right to refuse warranty replacement of consumables if they have been used in a projector with dirty airfilters. Only use the manufactures recommended cleaning kit which

R5976491 IQ PRO G500 01/02/2007

 

9

 

2. Installation Guidelines

has been specifically designed for cleaning optical parts, never use industrial strength cleaners on a projectors optics as these will degrade optical coatings and damage sensitive optoelectronics .

Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contaminants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will be non-effectiveand impracticable. Damage of this nature is under no circumstances covered under the manufactures warranty and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne particles in the environment of the projector. The manufacture reserves the right to refuse warranty repair if a projector has been subject to wantful neglect, abandon or improper use.

What about ambient light ?

The ambient light level of any room is made up of direct or indirect sunlight and the light fixtures in the room. The amount of ambient light will determine how bright the image will appear. So, avoid direct light on the screen. Windows that face the screen should be covered by opaque drapery while the set is being viewed. It is desirable to install the projection system in a room whose walls and floor are of non-reflectingmaterial. The use of recessed ceiling lights and a method of dimming those lights to an acceptable level is also important. Too much ambient light will ‘wash out’ of the projected image. This appears as less contrast between the darkest and lightest parts of the image. With bigger screens, the ‘wash out’ becomes more important. As a general rule, darken the room to the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable for illuminating small areas so that interference with the screen is minimal.

Which screen type ?

There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications. Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms of gain. The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a gain of 10 (x10) or more. The choice between higher and lower gain screens is largely a matter of personal preference and another consideration called the Viewing angle. In considering the type of screen to choose, determine where the viewers will be located and go for the highest gain screen possible. A high gain screen will provide a brighter picture but reduce the viewing angle. For more information about screens, contact your local screen supplier.

Image size

The projector is designed for projecting an image size with a screenwidth from 1.00m (3.3ft) to 6.00m (19.7ft) with an aspect ratio of 4 to 3.

Image retention

Image retention can affect LCD projectors, in extreme cases, permanent “burn” can occur if still/repetitive images are left on the screen for long periods of time. Such damage to the panels is NOT covered by warranty.

Please ensure that the following precautions are taken to avoid this phenomenon :

1.Use a screensaver (that moves)

2.Periodically change/alter any background images on the desktop

3.Turn off the projector when not in use.

2.3Projector configurations

The different configurations

1.Rear/Ceiling

2.Rear/Table

3.Front/Ceiling

4.Front/Table

10

 

R5976491 IQ PRO G500 01/02/2007

2. Installation Guidelines

1

2

3

4

Image 2-1

 

R5976491 IQ PRO G500 01/02/2007

 

11

2. Installation Guidelines

Positioning the projector

 

 

PD

 

 

P

 

 

front plate

a

SH

x

A

 

 

 

 

S

 

 

CD=SH/2+B-A

 

 

B

 

 

F

b

 

SW

 

 

S

 

 

SW

c

 

SH

 

 

F

Image 2-2

ON-Axisinstallation

aside view

btop view

cback view

x

optical axis projection lens

p

projector

s

screen

F

floor

12

 

R5976491 IQ PRO G500 01/02/2007

 

2. Installation Guidelines

 

 

PD

 

a

SH

 

 

 

 

front plate

P

 

S

 

 

 

 

A

 

 

B

CD=B-A

 

 

 

 

 

 

F

 

b

SW

 

 

 

S

SW

 

 

 

 

c

 

SH

 

 

 

F

 

Image 2-3

100% OFF Axis installation

aside view

btop view

cback view

x

optical axis projection lens

p

projector

s

screen

F

floor

CAUTION: Only for iQ Pro:

The harddisk in the IQ Pro server is formatted in horizontal position but can operate in all axes (6 directions). The projector should not be tilted more then +/- 5 degrees from these positions, otherwise error rates will increase.

R5976491 IQ PRO G500 01/02/2007

 

13

2. Installation Guidelines

CAUTION: Never place the projector on either side !

Floor

Floor

Image 2-4

2.4Lenses

Overview

Lenses

Lens formulas

Lens installation

Removing the lens

Cleaning the lens

2.4.1Lenses

Available lenses

The following lenses are available, or will become available (contact a BARCO service center) as an option :

Lenses

Standard version

 

 

QVD(0.85:1)

R9841220

 

 

QVD(1.3-1.8:1)

R9840950

 

 

QVD(1.9-2.6:1)

R9840960

 

 

QVD(3.0-6.0:1)

R9840970

 

 

QVD(7:1)

R9841230

 

 

SVD(2.0-2.5:1)

R9841240

 

 

The QVD (0.85:1) is to be used in ON Axis configuration only.

Shifting the lens vertically will not guarantee optimal image quality.

14

 

R5976491 IQ PRO G500 01/02/2007

 

 

 

2. Installation Guidelines

 

 

 

 

2.4.2 Lens formulas

 

 

Formulas

 

 

 

 

 

 

 

 

Metric Formulas (meter)

Inch formulas (inch)

 

 

 

 

 

QVD(0.85:1)

PD = -0.034+ 0.801 x SW + 0.0086 /SW

PD = -1.34+ 0.801 x SW + 13.35 /SW

 

 

 

 

 

QVD(1.3-1.8:1)

PDmin = 0.019 + 1.216xSW + 0.028/SW

PDmin = 0.75 + 1.216xSW + 43.4/SW

 

 

PDmax = -0.001+ 1.584xSW + 0.074/SW

PDmax = -0.04+ 1.584xSW + 115/SW

 

 

 

 

 

QVD(1.9-2.6:1)

PDmin = 0.052 + 1.731xSW - 0.014/SW

PDmin = 2.05 + 1.731xSW - 21.7/SW

 

 

PDmax = 0.11 + 2.33xSW - 0.059/SW

PDmax = 4.33 + 2.33xSW - 91.8/SW

 

 

 

 

 

QVD(3.0-6.0:1)

PDmin = 0.048 + 2.795xSW - 0.042/SW

PDmin = 1.89 + 2.795xSW - 65/SW

 

 

PDmax = 0.06 + 5.6xSW - 0.041/SW

PDmax = 2.36 + 5.6xSW - 63.4/SW

 

 

 

 

 

QVD(7:1)

PD = 0.013 + 6.35xSW + 0.005/SW

PD = 0.51 + 6.35xSW + 8.35/SW

 

 

 

 

 

SVD(2.0-2.5:1)

PDmin = -0.139+ 1.733xSW + 0.1/SW

PDmin = -5.47+ 1.733xSW + 153/SW

 

 

PDmax = 0.005 + 2.224xSW - 0.00862/SW

PDmax = 0.2 + 2.224xSW - 13.3/SW

 

 

 

 

Lens program to calculate the projector distance is available on the BARCO web site : http://www.barco.com/projection_systems/customer_services/lens_program.asp

2.4.3 Lens installation

How to install ?

1.Take the lens out of its packing material

2.Slide the lens door to the left (image 2-5)

3.Fix the lens by placing it in the housing

Note: In case of a motorized lens the female jack must be in front of the male jack located in theupper-leftpart of the housing in the projector(image 2-6)

4.Push carefully to lock the lens in the housing

5.Slide back the lens door to the right

R5976491 IQ PRO G500 01/02/2007

 

15

 

2. Installation Guidelines

Image 2-5

Image 2-6

CAUTION: Never transport the projector (or the whole unit) with the lens mounted on it ! Always remove the lens and transport it separately.

2.4.4Removing the lens

How to remove the lens ?

1.Slide the lens door to the left.

2.Unlock the lens by pulling the handle located on the right side of the projector (image 2-7)

3.Remove the lens out of its housing

Image 2-7

CAUTION: Never transport the projector with the lens mounted on it !

Always remove the lens before transporting the projector.

16

 

R5976491 IQ PRO G500 01/02/2007

2. Installation Guidelines

2.4.5Cleaning the lens

To minimize the possibility of damage to optical coatings, or scratches to lens surfaces, we have developed recommendations for cleaning. FIRST, we recommend you try to remove any material from the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.

Necessary tools

TorayseeTM cloth (delivered together with the lens kit). Order number : R379058.

How to clean the lens ?

Proceed as follow :

1.Always wipe lenses with a CLEAN TorayseeTM cloth.

2.Always wipe lenses in a single direction.

Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.

3.Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.

4.If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.

CAUTION: Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the cloth.

Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.

Other lenses can also be cleaned safely with this TorayseeTM cloth.

2.5Batteries

Overview

Battery installation

2.5.1Battery installation

How to install the battery

Two batteries are packed together with the RCU. Before using your RCU, install first these batteries.

1.Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU.

2.Lift up the top side of the cover at the same time.

3.Insert the batteries as indicated in the RCU.

4.Put the battery cover on its place.

R5976491 IQ PRO G500 01/02/2007

 

17

2. Installation Guidelines

18

 

R5976491 IQ PRO G500 01/02/2007

3. Connections

3. CONNECTIONS

Overview

Power connection

Input source connection

3.1Power connection

AC power (mains) cord connection

Use the supplied power cord to connect your projector to the wall outlet.

Plug the female power connector into the male connector at the front of the projector.

The power input is auto-rangingfrom 90 to 240 VAC.

I 0

Image 3-1

Fuses

For continued protection against fire hazard :

refer replacement to qualified service personnel

ask to replace with the same type of fuse.

3.2Input source connection

Overview

Input section

Input facilities

5-Cable input

Composite Video Input

S-Video input

Digital Visual Interface (DVI) input

Computer input

Communications Connections

Extended configuration

3.2.1Input section

Input Layers

The input section is divided in layers, each of them regrouping several inputs.

R5976491 IQ PRO G500 01/02/2007

 

19

3.Connections

1.Layer 1: analog layer containing analog data and video inputs

2.Layer 2: a hybrid layer containing 2 digital and 1 analog input

3.Layer 3 : network layer

3.2.2 Input facilities

overview

5–cableinput

composite video

component video (PR/Y/PB)

S-Video

Digital Visual Input (DVI)

Computer

network interface

Image 3-2

Source input section, the LED’s indicate the selection of a signal.

L1 Layer 1 = RGBHV (data) + Composite Video + S-Video

L2 Layer 2 = DVI + Computer + RS232 IN + RC (Wired Remote Control)

L3 Layer 3 = network Layer = Mic IN + Line IN + PC Card slot+ 4xUSB in + RJ45

20

 

R5976491 IQ PRO G500 01/02/2007

3. Connections

A cable cover is supplied with the projector and can be fitted on the front of the projector

Image 3-3

Cable basket : the white arrow shows the cables leaving the projector

AFront view

BBack view

3.2.35-Cableinput

Input specifications

The 5-cableinput section is made of 5 BNC input terminals.

0.7 Vpp ± 3dB

75 Ω terminated

Image 3-4

Component Video

In Component Video the term component describes a number (3) of elements that are needed to make up the video picture, these components are R-Y/Y/B-Y.A composite video signal on the other hand contains all the information needed for the color picture in a single channel of information

Which signals can be connected ?

Signals/Input BNC

R

G

B

H

V

 

 

 

 

 

 

RGBHV

R

G

B

H

V

 

 

 

 

 

 

RGsB1

R

Gs

B

-

-

RGBS1

R

G

B

S

-

Component

PR

Y

PB

-

-

 

 

 

 

 

 

1. data or video

R5976491 IQ PRO G500 01/02/2007

 

21

3. Connections

Beside the standard RGB, component and sync signals, the extended mode of the 5 Cable input makes processing of additional signals possible.

How to select a source on the 5 cable input ?

1.Press 1 on the RCU

Note: Another way for selecting this input is via the Menu

Component Video signals (PR/Y/PB)

Some interfaces use progressive output signals with a double line frequency of 32 kHz. The video decoder used for the video signals is not appropriate for these signals since it can only handle 16 kHz signals. This signal has therefore to be internally redirected, this is done in the Source selection menu by selectingData on BNC’s instead ofComponent video and by selectingPr/Y/Pb in the advanced settings of theImage file menu.

3.2.4Composite Video Input

Composite video connection

A Composite video signal is often available on a yellow cinch connector of a Camera, VCR or DVD player, in this case you will need an adapter cable cinch/BNC to connect to Video input of the RGB board.

Input specifications

The Composite video input section is made of 1BNC input terminal.

1.0 Vpp ± 3dB

75 Ω terminated

No loop through

Image 3-5

How to select a Composite Video Input ?

1.Press 3 on the RCU

Note: Another way for selecting this input is via the Menu.

The projector allows the input of more composite video signals (up to 7 composite video signals). "5 cable extended configuration", page 25

This note is not valid for the Pro version :

The Audio&Video optional layer(3) allows the use of an additional Video BNC input (referred to as Video2). The selection of this optional input happens the same way as the standard input (key 3)

22

 

R5976491 IQ PRO G500 01/02/2007

3. Connections

3.2.5S-Videoinput

S-Videoconnection

An S-Videosignal is available on theMini-Dinconnector of a camera, VCR or DVD player.

Input specification

Image 3-6

Which signal can be connected ?

Standard S-Video(S-VHS)with separate Y(luma) and C (chroma) signals.

How to select the S-Videoinput ?

1.Press 4 on the RCU

Note: Another way for selecting this input is via the Menu.

The projector allows the input of more S-Videosignals (up to 3 composite video signals)."S-Video extended configuration", page 26

This note is not valid for the Pro version:

The Audio&Video optional layer(3) allows the use of an additional S-Videoinput (referred to asS-Video4).The selection of this optional input happens the same way as the standard input (key 4)

3.2.6Digital Visual Interface (DVI) input

DVI

Digital Visual Interface is a display interface developed in response to the proliferation of digital flat panel displays.

The digital video connectivity standard that was developed by DDWG (Digital Display Work Group). This connection standard offers two different connectors: one with 24 pins that handles digital video signals only, and one with 29 pins that handles both digital and analog video. This standard uses TMDS (Transition Minimized Differential Signal) from Silicon Image and DDC (Display Data Channel) from VESA (Video Electronics Standards Association).

DVI can be single or dual link.

Input specifications

Single link DVI

Differential input voltage: 200 mV - 800mV

R5976491 IQ PRO G500 01/02/2007

 

23

3. Connections

Image 3-7

a DVI-Itype connector, analog link (4 pins at the right side of the connector) not supported

How to select the DVI Input ?

1.Press 5 on the RCU

Note: Another way for selecting this input is via the Menu.

3.2.7Computer input

Input specification

TTL sync input : U min = 2.0 V

RGB input = 0.7 Vpp ± 3dB

Image 3-8

What can be connected ?

RGBHV

RGSB

Composite sync only possible on Green

How to select a computer input ?

1.Press 2 on the RCU

Note: Another way for selecting this input is via the Menu.

3.2.8Communications Connections

Overview

RS232 IN connection

24

 

R5976491 IQ PRO G500 01/02/2007

3. Connections

3.2.8.1RS232 IN connection

What can be connected to the RS232 IN connection ?

The RS 232 IN connections allows the projector to communicate with a Computer e.g. IBM PC or Apple Macintosh.

Image 3-9

Applications of the RS232 connection

Remote control:

easy adjustment of projector via IBM PC (or compatible) or MAC connection.

address range from 1 to 255

allow storage of multiple projector configurations and set ups.

wide range of control possibilities

Data communication: sending data to the projector or copying the data from the projector to the computer

To set up the baudrate of the projector, see the Installation menu

3.2.9 Extended configuration

Overview

Introduction

5 cable extended configuration

S-Video extended configuration

Summarizing

3.2.9.1Introduction

What can be done ?

The PiP mode allows to display up to 4 windows of images coming from different sources. The extended capabilities on the input board allow therefore to combine several data & video sources, beside that, they allow switching between a wide range of input signals.

3.2.9.25 cable extended configuration

What can be done ?

Beside the standard RGB, composite & sync signals, the extended capabilities of the 5 cable inputs make treatment of additional signals possible:

a composite video signal may be connected to 4 of the 5 BNC’s (beside the standard video BNC input)

a S-Videosignal can be connected

R5976491 IQ PRO G500 01/02/2007

 

25

3. Connections

 

 

 

 

Inputs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

G

B

 

H

V

VIDEO

 

 

 

 

 

 

 

 

 

Signals

RGBHV

R

G

B

 

H

V

-

 

 

 

 

 

 

 

 

 

 

RGSB

R

GS

B

 

-

-

-

 

RGBS

R

G

B

 

S

-

-

 

 

 

 

 

 

 

 

 

 

Component

PR

Y

PB

 

-

-

-

 

 

 

 

 

 

 

 

 

 

S-Video

-

-

-

 

-

C

Y

 

 

 

 

 

 

 

 

 

 

S-Video

C

-

Y

 

-

-

-

 

 

 

 

 

 

 

 

 

 

Composite

VIDEO

-

-

 

-

-

-

 

 

 

 

 

 

 

 

 

 

Composite

-

VIDEO

-

 

-

-

-

 

 

 

 

 

 

 

 

 

 

Composite

-

-

VIDEO

 

-

-

-

 

 

 

 

 

 

 

 

 

 

Composite

-

-

-

 

-

VIDEO

 

 

 

 

 

 

 

 

 

 

 

Composite

-

-

-

 

-

-

VIDEO

 

 

 

 

 

 

 

 

 

Table 3-2

Extended configuration of the 5 cable input: the first column gives the possible signals, and the first row the 5 cable input connectors (+ the standard Video BNC).

How to set up the 5 cable extended configuration ?

1.Connect the video or S-videosource to the desired BNC connector

Note: In some cases an adapter cable is required(image 3-10, image 3-11,image 3-12)

Image 3-10

Connecting an S-Videosignal on the Vs & Video BNC

Image 3-11

Connecting an S-Videosignal on the R & B BNC

Image 3-12

Connecting composite Video signals on the 5 cable input

Multiple video signals can not be visualized simultaneously since there is only one decoder. However, the use of the optional Audio & video layer(3) allows to visualize up to 2 different video signals (in PiP mode ).

3.2.9.3S-Videoextended configuration

What can be done ?

Beside the standard luminance (Y) and chrominance (C) signals, the advanced capabilities of the S-Videoinput make treatment of additional signals possible:

2 composite video signal may be connected.

 

 

 

Inputs

 

 

 

 

 

 

 

Y

 

C

 

 

 

 

 

Signals

S-Video

Y

 

C

 

 

 

 

 

 

Composite Video

Video

 

-

 

 

 

 

 

 

Composite Video

-

 

Video

 

 

 

 

 

Table 3-3

Extended configuration of the S-Videoinput: the first column gives the possible signals, and the first row theS-Videoinputs pins.

26

 

R5976491 IQ PRO G500 01/02/2007

3. Connections

How to set up the S-Videoextended configuration ?

1.Connect the video sources to the desired connector (image 3-13)

Note: An adapter cable is required

Image 3-13

Connecting 2 composite Video signals on the S-Videoconnector

Multiple video signals can not be visualized simultaneously since there is only one decoder. However, the use of the optional Audio & video layer(3) allows to visualize up to 2 different video signals (in PiP mode ).

3.2.9.4Summarizing

Summarizing the extended connections

A composite video signal can be entered via 7 different inputs, which gives us 7 different video signals (not including optional video input):

1.Video R : via 1st BNC

2.Video G : via 2nd BNC

3.Video B : via 3rd BNC

4.Video VS : via 5th BNC

5.Video : via the standard composite video BNC input

6.Video Y : via S-Videoinput

7.Video C : via S-Videoinput

Key 3 on the RCU allows to browse through the active video inputs, each hit moves to the next active video input. The first hit on key 3 selects the last selected video input.

In the same way 3 S-Videosignals can be visualized through 3 different inputs

1.S-Video1: via the standardS-Videoinput

2.S-Video2 : via the 5 the BNC and the standard Composite Video input

3.S-Video3 : via the 1st and the 3rd BNC

Key 4 on the RCU allows to browse through the activeS-Videoinputs, each hit moves to the next active video input. The first hit on key 4 selects the last selected video input.

R5976491 IQ PRO G500 01/02/2007

 

27

3. Connections

28

 

R5976491 IQ PRO G500 01/02/2007

4. Getting started

4. GETTING STARTED

Overview

RCU & Local keypad

Terminology overview

Switching on

Lamp runtime

Lamp error

Quick set up adjustments

Projector address

Controlling the projector

Digital Zoom

Menu structure

Using the menu

Using the Dialogboxes

4.1RCU & Local keypad

How controlling the projector ?

The projector can be controlled by the local keypad or by the remote control unit.

Location of the local keypad ?

The local keypad is located on the topside of the projector.

For key overview: "Terminology overview", page 31

R5976491 IQ PRO G500 01/02/2007

 

29

4. Getting started

Image 4-1

Local keypad layout

Remote control functions.

This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set up. It includes automatic storing of picture controls (Brightness, Sharpness...) and settings.

Other functions of the remote control are :

switching between stand by and operational mode.

switching to "pause" (blanked picture, full power for immediate restarting)

direct access to all connected sources.

Diagnose LED’s

 

Green

Red

 

 

 

LED1

cool down sequence: flickers 60 seconds (120

rescue program (software error)

 

seconds in case of iQ 400 series) after switching

 

 

to standby

 

 

 

 

LED2

only for the versions containing a server:

hardware error

 

shows when projector is in

 

 

standby and server is active.

 

 

 

 

LED3

IR acknowledgement

continue : standby

 

 

flickers : Security = ON

 

 

 

30

 

R5976491 IQ PRO G500 01/02/2007

4. Getting started

4.2Terminology overview

Overview

The following table gives an overview of the keys.

Image 4-2

1

Function keys

user programmable keys with functions for direct access.

 

 

 

2

MENU

Menu key, to enter or exit the Toolbar menu.

 

 

 

3

Address key

(recessed key), to enter the address of the projector (between 0 and 9). Press the recessed

 

 

address key with a pencil, followed by pressing one digit button between 0 and 9.

 

 

 

4

LOGO key

allows to recall the stored Logo (not in PiP mode)

 

 

 

5

PAUSE

to stop projection for a short time, press ’PAUSE’. The image disappears but full power is

 

 

retained for immediate restarting.

 

 

 

6

STBY

standby button, to start projector when the power switch is switched on and to switch off the

 

 

projector without switching off the power switch.

 

 

Attention : Switching to Standby. When the projector is running and you want to

 

 

go to standby, press the standby key for 2 seconds.

 

 

 

7

MUTE

to interrupt the sound reproduction (audio = optional.

 

 

 

8

AUTOIMAGE

Auto image, to center the image on the active LCD surface.

 

 

 

9

Digit buttons

direct input selection.

 

 

 

9b

SOURCE button

this button allows to switch through the active (scanned) inputs

 

 

 

R5976491 IQ PRO G500 01/02/2007

 

31

4. Getting started

10

Lens control

use these buttons to obtain the desired ZOOM, SHIFT, FOCUS.

 

 

 

11

VOL

use this button to obtain the desired sound level (audio = optional)

 

 

 

12

Picture controls

use these buttons to obtain the desired picture analog level.

 

 

 

13

DIGI ZOOM

allows a digital Zoom of a part of the image

 

 

 

14

FREEZ

press to freeze the projected image.

 

 

 

15

PIP

allows to activate the PICTURE IN PICTURE mode

 

 

 

16

ENTER

to confirm an adjustment or selection in the MENU.

 

 

On the local keypad the ENTER button additionally accesses the PIP window resize function

 

 

 

17

Cursor keys

Cursor Keys on RCU or on the local keypad : to make menu selections or to access the

 

 

toolbar.

 

 

 

18

BACK

to leave the selected menu or item (go upwards to previous menu).

 

 

 

19

EFFECTS

not yet implemented

 

 

 

20

PIP ADJUST

allows to select a PiP window and change its configuration on screen

 

 

 

21

RC operating indication

lights up when a button on the remote control is pressed. (This is a visual indicator to

 

 

check the operation of the remote control)

 

 

 

22

IR receiver

IR receiver

 

 

 

Table 4-2

ordernumber RCU: R763794K

4.3Switching on

How to switch on.

1.Press the power switch to switch on the projector.

-When ’0’ is pushed in, the projector is switched off.

-When ’1’ is pushed in, the projector is switched on

The projector starts in standby mode, LED3 is red.

Starting image projection.

1. Press Standby key once on the local keypad or on the remote control.(image 4-3)

 

 

 

 

 

 

 

 

M EN U

 

 

 

B A C K

 

 

 

 

 

 

EN T ER

 

 

PA

U SE

L O G O

PI P

 

 

 

 

 

 

 

 

 

 

 

D

I G I

 

 

 

 

 

Z O O M

 

 

 

 

 

 

 

 

9

0

 

PH

A SE

Image 4-3

It may take about 60 seconds before image projection, i.e. no projection until the completion of several operations (software initialization,...).

32

 

R5976491 IQ PRO G500 01/02/2007

4. Getting started

If the Security mode is enabled, a textbox will be displayed for PIN code entry, see Security setting in the

Installation menu

4.4Lamp runtime

x

To generalize for the different projector types, x refers here to the maximum run time of the lamp.

Lamp runtime indication while running

Independently of the lamp mode, when the total runtime of an active lamp (lamp1 for example) is (x-30)hours or more, a warning message will be displayed.

Image 4-4

Lamp runtime management

Asingle mode

Bdual mode

x maximum lamp runtime

Image 4-5

warning message in case of an iQ300 projector

This warning message will be repeated at the next start up. Press BACK orMENU to remove the message.

R5976491 IQ PRO G500 01/02/2007

 

33

4. Getting started

The total lifetime of the lamp for a safe operation is “x” hours max, do not use it longer. Always replace with a same type of lamp. Call a BARCO authorized service technician for lamp replacement.

iQ Pro

x ( Max lamp runtime, in hours)

 

 

210L

6000

 

 

350

3000

 

 

500

1500

 

 

Table 4-3

Maximum runtime for the different iQ Pro projectors

When the lamp runtime reaches “x” hours the projector switches automatically to the other lamp, being lamp2.. following messages are displayed during and after switching.

Image 4-6

Image 4-7

When lamp2 at its turn reaches x-30hours, a warning message appears on the screen.

Image 4-8

warning message in case of a IQ300 series projector

At the end of the lifetime of lamp2 (x hours) the projector generates an alert message.

Image 4-9

A countdown time of 4 minutes is triggered before the projector is shut down (standby).

If the lamp runtime has not been reset, the alert message will reappear at the next start up (with again 4 minutes countdown time). This alert message can be escaped with MENU orBACK, but the countdown continues.

Contact a qualified Barco technician for lamp replacement.

In Dual mode the lamp end of lifetimes are reached at the same time, however if in dual lamp mode one lamp has been used more than the other (for example if the projector has been working temporarily in single mode), one lamp will reach its end of lifetime sooner than the other lamp, which brings us to the Single mode operation.

WARNING: Using a lamp for more than x hours is dangerous as the lamp could explode.

The lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized technician.

4.5Lamp error

What happens in case of a lamp error ?

When a lamp error occurs in dual mode, a dialogbox is displayed informing the user of the steps to be taken.

34

 

R5976491 IQ PRO G500 01/02/2007

4. Getting started

Image 4-10

The message will dissapear after 2 minutes, it can also be escaped.

The projector will switch to single lamp mode and displays an icon (right top corner of the screen) representing a crossed out lamp, that way informing the user of an earlier lamp error.

The icon can always be removed via the Clear lamp error function in theLamp menu.

WARNING: In case of lamp error contact a Barco authorized technician.

4.6Quick set up adjustments

Overview

Quick lens Adjustment

Using the RCU

4.6.1Quick lens Adjustment

What can be done ?

For a quick lens set up and image shift, use the RCU dedicated keys or the lens button on the local keypad

Zoom/focus are only available for motorized lenses.

Quick zoom/focus adjustment

1.Press LENS ZOOMor LENS FOCUSon the RCU

2.Use the arrow keys to adjust

Quick shift adjustment

1.Press LENS SHIFT

2.Use the arrow keys to adjust

4.6.2Using the RCU

Pointing to a reflective screen

1. Point the front of the RCU to the reflective screen surface. (image 4-11)

R5976491 IQ PRO G500 01/02/2007

 

35

4. Getting started

Image 4-11

When using the remote control, make sure you are within the effective operating distance.

The operating distance may be up to 15 m (50ft).

The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control and the IR sensor.

How to connect ?

1.Plug one end of the remote cable in the connector on the bottom of the RCU.

2.Plug the other end in the connector in the front panel of the projector labelled RC.(image 4-12)

Image 4-12

Specifications of the RC input

Uin = 9V

Imax = 80 mA

Internal IR receivers can be disabled:

mono jack : on plug in of the jack

stereo jack : on plug in or using an external switch bringing the right channel (B) to ground level.

36

 

R5976491 IQ PRO G500 01/02/2007

4. Getting started

A

B

C

 

 

D

Image 4-13

Stereo jack pin configuration

Atip: Left channel

Bring: right channel

Cscreen: common (GND)

Dexternal switch

The Remote connection uses a standard two wire cable terminated on each end with a 3.5 mm male (mono/stereo) phone jack.

This cable is not delivered but is available in most electronical or audio shops.

4.7Projector address

Overview

Address setting

Displaying and Programming addresses into the RCU

4.7.1Address setting

Projector address

Address installed in the projector to be individually controlled.

Common address

Default address. Projector will always execute the command coming from a RCU programmed with that common address.

Why a projector address ?

As more than one projector can be installed in a room, the separate projector should be separately addressable with an RCU or computer. Therefor each projector has its own address.

Set up an individual Projector Address.

The set up of a projector address can be done via the software.

Projector controlling.

Every projector requires an individual address between 0 and 255 which can be set in the Installation menu.

When the address is set, the projector can be controlled by :

RCU for addresses between 0 and 9.

computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.

A projector will respond to a RCU set to the common address ’0’ regardless of what address is set in the projector itself (common address of projector should also be “0” ).

The RCU is default programmed with address 0 , ’common address’.

If it is necessary to control a specific projector, then enter the projector address into the RCU (only when that address is between 0 and 9). The projector with the corresponding address will listen to that specific RCU.

R5976491 IQ PRO G500 01/02/2007

 

37

4. Getting started

Some projectors may operate in domestic environments where other equipments may listen to the common address “0” , therefore the common address can also be set to “1”.

4.7.2Displaying and Programming addresses into the RCU

Displaying the Projector Address on the Screen.

1.Press the Address key (recessed key on the RCU) with a pencil. The projector’s address will be displayed in a ’Text box’

To continue using the RCU with that specific address, it is necessary to enter the same address with the digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the Address key displays projector address 003, then press "3" digit button on the RCU to set the RCU’s address to match the projector’s address. Do not press 0–0–3 .This will address the remote control to ’0’ and control all projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default address (zero address) and controls then all projectors in the room.

Address 0 (or 1) should always allow communication with the projector since it is a common address.

Displaying the Projector Address in Standby.

1.Press the Address key (recessed key on the RCU) with a pencil. All the LED’s on the front of the projector go out.

Then LED1 starts blinking green the number of hundreds. After that LED2 starts blinking the number of tens. Finally LED3 starts blinking green the number of units. If this is done, the original status of the leds is restored.

4.8Controlling the projector

Input Selection

Key in the corresponding slot number with the digit keys on the RCU. The selected source will be displayed.

Picture Controls

When an image control is pressed, a text box with a bar scale, icon and function name of the control, e.g. ’brightness...’ appears on the screen (only if Textbox in the Installation menu is ON). The length of the bar scale and the value of the numeric indication indicate the current memorized setting for this source. The bar scale changes as the arrows on the RCU are pressed or the + or - buttons on the local keypad.

The picture settings are saved in the image file.

Image 4-14

Brightness

Use the + button for a higher brightness.

 

Use the - button for a lower brightness.

 

 

Contrast

Use the + button for a higher contrast.

 

Use the - button for lower contrast.

 

 

Color

Use the + button for richer colors.

 

Use the - button for lighter colors.

 

 

Tint(Hue)

Tint is only active for Video and S-Videowhen using the NTSC 4.43 or NTSC 3.58 system.

 

Use the + button

 

Use the - button.

 

 

38

 

R5976491 IQ PRO G500 01/02/2007

4. Getting started

Sharpness

Use the + button for a sharper picture.

 

Use the - button for a softer picture.

 

 

Phase

Use the + or - button to adjust the phase.

 

 

Gamma

Use the + button for a higher gamma

 

Use the - button for a lower gamma

 

 

Freeze

Press Freeze to freeze the displayed image.

 

 

The Pause Key

When the Pause key is pressed, the image projection is stopped, a black screen will be displayed

To restart the image projection:

Press PAUSE key

Press BACK key

Select a source number

4.9Digital Zoom

What can be done ?

The Digital Zoom key on the RCU allows to zoom (in or out) one particular part of the image

How to Zoom ?

1.Press ← or → on the Digital Zoom key on the remote to Zoom the center of the image A wizardbox is displayed in the lower part of the screen, follow the instructions.

Use the BACK key to undo the Zoom function.

Digital Zoom can not be performed on a logo.

4.10 Menu structure

PC like menustructure

The projector has a build in "PC like" toolbar menu which allows easy access to different parameters for setting up the projector. The menu is activated by pressing MENU, it contains 2 levels depending on the type of user:

Level 1: standard user

Level 2: advanced user, level 2 is password protected, the advanced parameters are only visible when the correct password has been entered ( factory password = "0000")

Menu items which are not applicable are greyed out.

4.11 Using the menu

Menu Layout

A grey line gives the transition between standard and advanced parameters.

The existence of a submenu is indicated by a white arrow, Settings is a submenu.

Keystone is an item of theImage menu.

R5976491 IQ PRO G500 01/02/2007

 

39

 

4. Getting started

Three suspension points indicate that the menuitem hides a dialogbox or a textbox.

Image 4-15

The menus inserted in this manual are of the advanced type: all the items are visible The menus seen by a standard user on the screen will hence not correspond with the menus in the manual i.e. the advanced items will not be visible, they will be replaced with "More..."

Greyed out menus or items are not available in this software version

How to pull down a menu ?

1. Use ↓ to pull down a menu

How to pull down a submenu ?

1. Use → to pull down a submenu

How to exit the submenu ?

1. Press BACK to exit a submenu

Press MENU to exit the menu

When the menu has been exited for more than 1 minute, the advanced user password has to be re-entered.

4.12 Using the Dialogboxes

How to use the dialogboxes ?

Some parameters are modified by means of a dialogbox, where selections can be made and/or values can be entered, The values can be entered in several ways:

Entering numeric values using the numeric keys on the remote control

1.Press ENTER to activate the input field(image 4-16)

2.Key in the desired value

40

 

R5976491 IQ PRO G500 01/02/2007

4. Getting started

Image 4-16

Entering numeric values using the arrow keys on the remote control

1.Press ENTER to activate the input field.

2.Press ←or → to select the digit to be changed (image 4-17)

3.Press ↓ or ↑ to increase or decrease the value

Image 4-17

Entering numeric values using the arrow keys on the local keypad

1.Press ENTER to activate the input field.

2.Press ←or → to select the digit to be changed

3.Press ↓ or ↑ to increase or decrease the value

To confirm the changes always press ENTER.

Use ↓ or ↑ to browse between the different fields.

In some cases an alphanumeric value (file name, ...) has to be entered. Use ↑ or ↓ to scroll through the character values once the input field is activated

Following characters can be browsed in this particular order:

Decimal scroll list: 0123456789

Signed decimal scroll list: 0123456789-

ASCII scrolllist:ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789+-*/&@#.;.abcdefghijklmnopqrstuvwxyz

R5976491 IQ PRO G500 01/02/2007

 

41

4. Getting started

42

 

R5976491 IQ PRO G500 01/02/2007

5. Source Selection

5. SOURCE SELECTION

Overview

Source selection

Composite Video

S-Video

The Video Selector

5.1Source selection

Selecting a source

The Source selection menu allows to select one of the different sources. Another method to select an input source is via the remote control using the numeric keys or by using the local keypad.

When selecting a source with a different resolution (and/or aspect ratio) than the projector’s resolution (and/or aspect ratio ), the source can be shown in its native resolution or can be re-scaledto the projector’s resolution, the latter case brings of course some loss of quality.

For more info on resolution match see the Show native resolution function in the Image menu.

How to select a source ?

1.Press MENU to activate the Tool bar

2.Press ↓ to Pull down the Source Selection menu (image 5-1,image 5-2)

3.Use ↑ or ↓ to select one of the different sources ( Press → to Pull down if the item has a submenu)

4.Press ENTER to confirm your choice

On the screen appears now the selected source.

Image 5-1

R5976491 IQ PRO G500 01/02/2007

 

43

5. Source Selection

Image 5-2

The Barco logo on the menu indicates the presence of a signal, the digit indicates the shortcut key on the RCU.

The 3 first sources (Data on BNC’s, Component Video & RG(s)B) refer to the 5-cableinput, the position of the indication “1” will always show which BNC configuration is selected.

When to select “Data on BNC’s”

Select Data on BNC’s when a data signal is connected to the BNC’s

When to select “Component video” ?

Select Component video when a video signal of the type (R-Y/Y/B-Y)is connected on the BNC’s.

When to select RGsB Video ?

Select RGsB Video when an RGB video signal (15 KhZ) with Sync on green or sync on H is presented on the BNC’s. This signal is routed to the video circuit and is projected in a Video Window.

5.2Composite Video

How to select one of the 7 composite video inputs ?

1.Press MENU to activate the Tool bar

2.Press ↓ to Pull down the Source Selection menu

3.Use ↑ or ↓ to select Composite video

4.Press → to Pull down the submenu

5.Use ↑ or ↓ to select one of the different video inputs (image 5-3)

Note: Video2 is an optional Video input and is only displayed in case the optional Video/Audio layer is installed.

If the extended mode is disabled, the submenu contains only 1 selection (2 selections if the Audio & Video option is installed).

6.Press ENTER to confirm your choice

A white bullet indicates the selected composite video source which now appears on the screen.

44

 

R5976491 IQ PRO G500 01/02/2007

 

5. Source Selection

Image 5-3

Adjustments on a Composite video signal

The projectors allows different adjustments on a composite video signal. Depending on the type of signal (NTSC /PAL) the terminology may differ :

Contrast

Brightness

Color : adjusts the level of color saturation in a PAL signal

Tint : adjusts the level of color saturation in an NTSC signal

AGC: Automatic Gain Control

The composite video sources can also be selected using the video selector or via the dedicated key 3 on the RCU. Key 3 allows to browse through the active video inputs when the extended mode is checked in Video Selector..

5.3S-Video

When

Select the S-Videoinput when in presence of a video signal also calledS-VHSsignal.

An S-Videosignal is available on theMini-Dinconnector of a camera, VCR or DVD player.

How to select one of the 3 S-Videoinputs ?

1.Press MENU to activate the Toolbar

2.Press ↓ to Pull down the Source Selection menu

3.Use ↑ or ↓ to select S-Video

4.Press → to Pull down the submenu

5.Use ↑ or ↓ to select one of the different video inputs (image 5-4)

Note: S-Video4is an optional Video input and is only displayed in case the optional Video/Audio layer is installed

If the extended mode is disabled, the submenu contains only 1 selection (2 selections if the Audio & Video option is installed).

6.Press ENTER to confirm your choice

A white bullet indicates the selected video source which now appears on the screen.

R5976491 IQ PRO G500 01/02/2007

 

45

 

5. Source Selection

Image 5-4

The S-Videosources can also be selected using the video selector or via the dedicated key 4 on the RCU. Key 4 allows to browse through the activeS-Videoinputs when the extended mode is checked in Video Selector.

5.4The Video Selector

Video Selector

The Video Selector is a graphical interface which allows an overview of the different video inputs (Composite Video and S-Video)and whether they are active (signal connected) or not as well as the selection of these different signals.

Video selector modes

The video selector has two modes:

standard mode : the video selectable video inputs are the standard composite video & the S-Videoinput

extended mode : several BNC connections are added and can be selected as video inputs (S-Videoinputs).

How to display the Video Selector ?

1.Press MENU to activate the Tool bar

2.Press ↓ to Pull down the Source Selection menu

3.Use ↑ or ↓ to select Video selector

4.Press ENTER

On the screen appears a message, (image 5-5)

followed by a graphical interface (image 5-6,image 5-7)

A BNC or S-Videoconnector on the video selector can be in one of following conditions:

-A: connector disabled

-B: connector enabled but inactive (no video signal present on connector)

-C: connector enabled & active (video signal present on connector

-D: connector enabled active & selected

-E: connector enabled & active & focused (browser positioned on connector)

MESSAGE

Scanning video inputs

Please wait ...

Image 5-5

46

 

R5976491 IQ PRO G500 01/02/2007

5. Source Selection

A A

B B

C C

D D

E E

Image 5-7

Image 5-6

If the Audio/Video option is installed the Video Selector is updated with the additional Video & S-Videoinput

Image 5-8

How to select an input on the Video Selector ?

1.Use ←or→ to browse through the different inputs

2.Press ENTER

Use MENU orBACK to exit the Video Selector

How to disable the extended Video Selector

1.Use the arrow keys to select the Extended checkbox

2.Press ENTER to disable the extended mode

The standard Video Selector is displayed (image 5-9)

R5976491 IQ PRO G500 01/02/2007

 

47

5. Source Selection

Image 5-9

48

 

R5976491 IQ PRO G500 01/02/2007

6. General Menu

6. GENERAL MENU

Overview

Pause

Freeze

Standby Timer

Audio (Optional)

Identification

6.1Pause

Interrupting the image projection

With the Pause function, the image projection can be stopped, the projector remains with full power for immediate restart. The projection is interrupted by means of a mechanical shutter cutting the light beam.

How to interrupt the image projection ?

1.Press MENU to activate the Tool bar

2.Press → to select General

3.Press ↓ to Pull down the General menu

4.Use ↑ or ↓ to select Pause (image 6-1)

5.Press ENTER to activate the Pause function

A brief sound indicates that the shutter has been activated.

Image 6-1

The image projection can also be interrupted using the PAUSE key on the RCU.

To restart the image : press PAUSE

6.2Freeze

Freezing the image

With the Freeze function, the image can be frozen. To restart the image, reuse the Freeze function or press the FREEZE button on the remote.

How to freeze the image ?

1.Press MENU to activate the Tool bar

2.Press → to select General

3.Press ↓ to Pull down the General menu

4.Use ↑ or ↓ to select Freeze (image 6-2)

5.Press ENTER to activate the Freeze function

R5976491 IQ PRO G500 01/02/2007

 

49

 

6. General Menu

Image 6-2

The image can also be frozen using the FREEZE key on the RCU

6.3Standby Timer

Purpose of the Standby Timer

If there is no signal, and the standby timer is enabled, a dialogbox is displayed and the projector will shut down after a determined time.

The countdown time can be set in a dialog box in a range from 180 to 3600 seconds (default value = 300). The Timer can also be disabled.

How to enable the timer ?

1.Press MENU to activate the Tool bar

2.Press → to select General

3.Press ↓ to Pull down the General menu

4.Use ↑ or ↓ to select Standby Timer (image 6-3)

5.Press ENTER to activate the function

On the screen appears a dialogbox (image 6-4)

6.Use ↑ or ↓ to select Enabled, a box surrounds the selected item, pressENTER to activate

7.Use ↑ or ↓ to browse to the input field

8.Use ←or→ , the numeric keys on the remote or the keypad to change the countdown setting

9.Press MENU orBACK to exit or to go back to the previous menu

Image 6-3

50

 

R5976491 IQ PRO G500 01/02/2007

6. General Menu

Image 6-4

6.4Audio (Optional)

Overview

Audio Setup

Audio Settings

6.4.1Audio Setup

What can be done ?

Layer 3 allows the input of 4 audio signals, each of them can be linked to the corresponding (video or data) source signal. it is also possible to link multiple audio signals to one video (or data) source signal, this can be useful in case of teleconferencing.

The configuration has to be done in the Audio Setup menu

Starting the Audio Setup menu

1.Press MENU to activate the Tool bar

2.Press → to select General

3.Press ↓ to Pull down the General menu

4.Use ↑ or ↓ to select Audio setup (image 6-5)

5.Press ENTER

A dialog box is displayed (image 6-6)

-LED is red : audio input is mute

-LED is green : input is active (linked image source is selected)

-LED is orange : image source is not selected

Image 6-5

R5976491 IQ PRO G500 01/02/2007

 

51

6. General Menu

Image 6-6

How to mute an Audio channel ?

1.use the arrow keys to select the desired mute box

2.Press ENTER

How to link an audio input to a source ?

1.use the arrows to select the desired scroll box

2.Press ENTER to open the scroll box

3.use ↑ or ↓ to select the source

4.Press ENTER

When the source switching mode is the fade in/out mode, the audio switching will also be done using a fade in/out effect.

6.4.2 Audio Settings

Audio Settings

1.Press MENU to activate the Tool bar

2.Press → to select General

3.Press ↓ to Pull down the General menu

4.Use ↑ or ↓ to select Audio setup (image 6-7)

5.Press ENTER

A dialog box is displayed (image 6-8)

6.Use the arrow keys to select and change the settings

Note: The default value for the volume is 43, this corresponds to a gain factor of 1 (volume in = volume out).

Image 6-7

52

 

R5976491 IQ PRO G500 01/02/2007

6. General Menu

Image 6-8

6.5Identification

The projector’s identification screen

The identification screen displays the projector’s main characteristics

How to display the identification screen ?

1.Press MENU to activate the Tool bar

2.Press → to select General

3.Press ↓ to Pull down the General menu

4.Use ↑ or ↓ to select Identification (image 6-9)

5.Press ENTER to activate the function On the screen appears a text box.

In this case the projector is an iDR500 (image 6-10)

6.Press MENU orBACK to exit or to go back to the previous menu

Image 6-9

R5976491 IQ PRO G500 01/02/2007

 

53

6. General Menu

Image 6-10

54

 

R5976491 IQ PRO G500 01/02/2007

7. Image Menu

7. IMAGE MENU

Overview

Settings

Aspect ratio

Show native resolution

Keystone

Color temperature

Filmmode detection

Blanking

Input balance

AGC on Video

Manual Gain Control

7.1Settings

Overview

Contrast

Brightness

Color

Tint (hue)

Sharpness

Gamma

Phase

Noise reduction

What can be done ?

Correct image settings are important for a good image reproduction. The image settings are made through a dialog box with a scroll bar. Minimal, maximal and actual values are indicated. These settings can also be done directly via the RCU’s dedicated buttons, except for the sharpness.

Image 7-1

Image 7-2

R5976491 IQ PRO G500 01/02/2007

 

55

7. Image Menu

7.1.1Contrast

Contrast adjustment

Adjust the contrast to “brighten” the white parts of the image.

It is recommended to adjust the brightness before adjusting the contrast.

How to change the contrast

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select settings

5.Press → to pull down the menu

6.Use ↑ or ↓ to select Contrast

7.Press ENTER

On the screen appears now a sliderbox (image 7-3)

8.Use ←or → , the numeric keys on the remote, or the keypad to change the contrast

Image 7-3

7.1.2Brightness

Brightness adjustment

Adjusting the brightness will affect the dark areas of the image. Increase the brightness to “lighten” up the parts that are too dark.

How to change the Brightness ?

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select settings

5.Press → to pull down the menu

6.Use ↓ or ↑ to select Brightness

7.Press ENTER

On the screen appears now a sliderbox (image 7-4)

8.Use ←or → , the numeric keys on the remote, or the keypad to change the Brightness

Image 7-4

7.1.3Color

Color adjustment

Adjust the color to obtain more or less saturated colors.

56

 

R5976491 IQ PRO G500 01/02/2007

7. Image Menu

How to change the Color ?

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select settings

5.Press → to pull down the menu

6.Use ↓ or ↑ to select Color

7.Press ENTER

On the screen appears now a sliderbox (image 7-5)

8.Use ←or → , the numeric keys on the remote, or the keypad to change the Color

Image 7-5

7.1.4Tint (hue)

How to change the Tint ?

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select settings

5.Press → to pull down the menu

6.Use ↓ or ↑ to select Tint

7.Press ENTER

On the screen appears now a sliderbox

8.Use ←or → , the numeric keys on the remote, or the keypad to change the Tint

7.1.5Sharpness

How to change the sharpness ?

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select settings

5.Press → to pull down the menu

6.Use ↓ or ↑ to select sharpness

7.Press ENTER

On the screen appears now a sliderbox

8.Use ←or → , the numeric keys on the remote, or the keypad to change the sharpness

7.1.6Gamma

How to change the Gamma

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select settings

R5976491 IQ PRO G500 01/02/2007

 

57

 

7.Image Menu

5.Press → to pull down the menu

6.Use ↓ or ↑ to select Gamma

7.Press ENTER

On the screen appears now a sliderbox

8.Use ←or → , the numeric keys on the remote, or the keypad to change the Gamma

7.1.7Phase

Phase adjustment

A bad phase adjustment will result in bad transitions and sometimes noise (text can end to be unclear).

How to change the Phase ?

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select settings

5.Press → to pull down the menu

6.Use ↓ or ↑ to select Phase

7.Press ENTER

On the screen appears now a sliderbox (image 7-6)

8.Use ←or → , the numeric keys on the remote, or the keypad to change the Phase

Image 7-6

7.1.8Noise reduction

How to change the Noise reduction ?

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select settings

5.Press → to pull down the menu

6.Use ↓ or ↑ to select Noise reduction

7.Press ENTER

On the screen appears now a sliderbox

8.Use ←or → , the numeric keys on the remote, or the keypad to change the Noise reduction setting.

7.2Aspect ratio

Aspect ratios

The standard aspect ratio used in broadcast television is the 4:3 ratio. However, most of the DVD sources use nowadays the widescreen 16:9 or even the cinemascope 2.35:1 aspect ratio.

Some DVD sources may even use the anamorphic 16:9 or anamorphic 2.35:1 to take advantage of the higher vertical resolution offered by the 4:3 ratio. The “anamorphic” term means that the original widescreen image is squeezed in order to fit the 4:3 aspect ratio.

58

 

R5976491 IQ PRO G500 01/02/2007

7. Image Menu

4:3

16:9

2.35:1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 7-7

Common nonanamorphic aspect ratios in DVD sources

16:9

2.35:1

 

 

 

Image 7-8

Anamorphic aspect ratios in DVD sources

What can be done ?

The aspect ratio setting forces the projector to project an image using a defined aspect ratio :

4:3

16:9

5:4

Auto

The settings do not refer to the aspect ratio of the source !

R5976491 IQ PRO G500 01/02/2007

 

59

7. Image Menu

Source

4:3

16:9

 

Projector setting

4:3

16:9

5:4

2.35:1

16:9 anamorphic

2.35:1 anamorphic

Image 7-9

Possible aspect ratio settings and their effect on different sources in the iQ.

We can conclude that the thumb rule for DVD projection is to always leave the projector in 4:3 format except when dealing with anamorphic sources where the 16:9 setting allows the best reproduction.

The Auto function calculates an aspect ratio based on the information stored in the image files.

Selecting Auto in case of a Video source may shrink the image horizontally

How to change the Aspect ratio ?

1.Press MENU to activate the Tool bar

2.Press → to select Image

3.Press ↓ to Pull down the Image menu(image 7-10)

4.Use ↑ or ↓ to select Aspect ratio

5.Use → open the Aspect ratio menu

6.Use ↑ or ↓ to select the desired ratio

7.Press ENTER to confirm

60

 

R5976491 IQ PRO G500 01/02/2007

 

7. Image Menu

Image 7-10

The aspect ratio settings are greyed out in case the Show native resolution or theFull screen representation setting is enabled.

How to set a custom Aspect ratio ?

1.Press MENU to activate the Tool bar

2.Press → to select Image

3.Press ↓ to Pull down the Image menu(image 7-11)

4.Use ↑ or ↓ to select Aspect ratio

5.Use → open the Aspect ratio menu

6.Use ↑ or ↓ to select Custom

7.Press ENTER to confirm

A dialog box is displayed (image 7-12)

8.Enter the values for width and height of the image The image aspect ratio is updated.

Image 7-11

R5976491 IQ PRO G500 01/02/2007

 

61

7. Image Menu

Image 7-12

7.3Show native resolution

Graphics

Native resolution of the LCD panels = 1024 pixels x 768 pixels (4:3)

Reality(SXGA)

Native resolution of the LCD panels = 1366 pixels x 1024 pixels (4:3)

Reality(SXGA+)

Native resolution of the LCD panels = 1400 x 1050 pixels (4:3)

What can be done ?

The aim here is to always show the resolution of the source independently of the resolution of the LCD panels. This way better image reproduction is obtained since no up or down scaling is done on the source.

Note that native resolution refers here to the source and does thus only have sense when handling data sources (greyed out for video sources).

Depending on the type of projector the “show native resolution” function will handle the sources as follows:

Source

 

 

Projected image

 

 

 

 

 

 

 

 

 

Name

Ratio

Resolution

Ratio

Resolution

Particularities Reality

Particularities

 

 

 

 

 

(SXGA+)

Graphics

 

 

 

 

 

 

 

 

 

 

 

 

 

xga

4:3

1024x768

4:3

1024x768

image centered +side

image centered

 

 

 

 

 

blanked

 

 

 

 

 

 

 

 

sxga

5:4

1280x1024

5:4

1280x1024

image centered +side

scroll image

 

 

 

 

 

blanked

 

 

 

 

 

 

 

 

sxga+

4:3

1400x1050

4:3

1400x1050

image centered

scroll image

 

 

 

 

 

 

 

uxga

4:3

1600x1200

4:3

1600x1200

scroll image

scroll image

 

 

 

 

 

 

 

Table 7-1

Show native resolution = ON in case of a Graphics(XGA) and Reality (SXGA+) iQ Pro projector

The Full screen representation function on the other hand forces to use the complete native resolution of the LCD panels.

How to enable the “Show native resolution” function?

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

62

 

R5976491 IQ PRO G500 01/02/2007

 

7. Image Menu

4.Use ↑ or ↓ to select Show native resolution (image 7-13)

5.Press → to pull down the menu

6.Use ↓ or ↑ to select On

7.Press ENTER

A white bullet shows the selection

Image 7-13

The default mode is used if the show native resolution and thefull screen function are off.

The default mode shows always the native ratio and forces the native resolution of the panels (part of the image blanked where needed)

When show native resolution is ON and the resolution of the source is higher than the panel resolution , use the arrow keys to scroll through the image (pan).

7.4Keystone

What can be done ?

The Keystone adjustment is used to align the image, this can be necessary when projecting under a non standard angle

How to perform a Keystone correction ?

1.Press MENU to activate the Tool bar

2.Press → to select Image

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select Keystone (image 7-14)

5.Press ENTER to confirm

A sliderbox is displayed . (image 7-15)

Use ← or →, the numeric keys on the remote, or the keypad to adjust the keystone. The Top and bottom adjustments affect the image differently. (image 7-16,image 7-17)

R5976491 IQ PRO G500 01/02/2007

 

63

 

7. Image Menu

Image 7-14

Image 7-15

Image 7-16

 

Top adjustment of the keystone

Image 7-17

Bottom adjustment of the keystone

7.5Color temperature

What can be done ?

The color temperature can be selected according to the type of source:

There are 4 different preset color temperatures:

Projector white

computer : 9300 K

Video : 6500 K

Film : 5400 K

Broadcast : 3200 K

These calibrated presets can be selected and will provide optimum color tracking, the projector allows however the setting of a personal color temperature, this is done in custom

How to select a preset color temperature ?

1.Press MENU to activate the Tool bar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

64

 

R5976491 IQ PRO G500 01/02/2007

7. Image Menu

4.Use ↑ or ↓ to select Color temperature

5.Press → to pull down the menu

6.Use ↓ or ↑ to select the desired preset color temperature

7.Press ENTER

The color temperature of the image is adapted and a white bullet shows the active setting.

How to start up the custom color temperature ?

1.Press MENU to activate the Tool bar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select Color temperature

5.Press → to pull down the menu

6.Use ↓ or ↑ to select custom

7.Press ENTER

A slider box for the red custom setting is displayed as well as a wizard text box in the lower part of the screen. (image 7-18, image 7-19)

Follow the instructions on the wizard textbox. (image 7-20)

Image 7-18

Image 7-19

Image 7-20

7.6Filmmode detection

What can be done ?

Some sources like common DVD material are derived from cinema 24 Hz sources (2/2 or 3/2 pull down method).

R5976491 IQ PRO G500 01/02/2007

 

65

7. Image Menu

VIDEO PAL

NTSC VIDEO

 

50f/s

FILM

60 f/s

 

24 f/s

 

167

167

 

 

160

 

 

 

 

 

 

133

120

125

 

 

 

 

 

80

83

 

83

 

 

 

 

 

 

1/30s

 

 

 

50

40

42

 

 

 

 

 

 

 

 

1/20s

0

0

2/2

3/2

Image 7-21

film to video conversion: 2/2 and 2/3 pull down method

The filmmode detection insures that these converted signals are shown without artefacts, especially motion artefacts due to bad de-interlacing.

Image 7-22

This function may cause undesired effects on standard sources, therefore it can be disabled (OFF) at any time

Enabling/disabling the filmmode detection

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select Filmmode detection

5.Press → to pull down the menu

6.Use ↓ or ↑ to enable or disable the Filmmode detection

7.Press ENTER

A white bullet shows the active setting (image 7-23)

66

 

R5976491 IQ PRO G500 01/02/2007

 

7. Image Menu

Image 7-23

7.7Blanking

Blanking in the Image menu

The blanking in general allows to blank unwanted video information (noise in the top or bottom of the image).

The blanking in the image menu is the same as in the Display settings menu except for the fact that here the blanking settings are stored in the image files. In other words each custom file or source has its own blanking values.

See the blanking procedure in the Display settings menu.

If the selected source is not entirely displayed always check first the blanking settings in the image menu since the active custom file may contains blanking.

7.8Input balance

Introduction: Unbalanced color signals

When transporting signals, there is always a risk of deterioration of the information contained in the signals.

In case of information contained in the amplitude of the signals which is the case of data color signals (R, G, B),image 7-24 ,weare quite sure that the amplitude of these color signals is subject to alterations.

An example of alteration may be a DC component added to the signal, in the form of a DC offset repositioning the black level, since this black level (“brightness”) will become crucial later on ( clamping circuit) it will result in “black not being black”.

Another value that is subject to alteration is the amplitude of the signal, resulting in an altered “Gain” of the signal (“white level” orcontrast ).

The alterations of the three color signals will happen independently i.e. the colors will end to be unbalanced, image 7-25

B

0.7V

Black level

Image 7-24

R5976491 IQ PRO G500 01/02/2007

 

67

7. Image Menu

G B

R

R

G

∆Β

 

 

Black level

Image 7-25

One can conclude here that a good color tracking can only be met by using three previously (input) balanced color signals

Analog Digital Conversion

The analog color signals must pass through an Analog/Digital conversion circuit prior to any digital processing in the PMP. A typical ADC transforms the analog value into an 8 bit coded digital signal.

The graphic shows that when converting a signal containing a DC offset component the range of the converter is not optimally used.

ADC

R

 

255

 

 

 

 

 

 

 

i2 : video information

 

0

i1 : superfluous information

 

Black level

 

 

 

 

 

Image 7-26

 

 

 

One can conclude here that a good data conversion can only be met by using three previously (input) balanced color signals

The objective of input balancing

The objective in input balancing is to “set” the same black level and the same white level for the three colors of a particular input source.

Black level setting : brightness

White level setting : contrast

The same absolute black and white level for the three colors allows the same reference for Brightness and contrast control of the picture !

These two references also set the range in which the ADC will work for that particular source ( this explains also why each input balance setting is linked to a particular source and thus saved in the image file).

How can it be done ?

To balance the three color signals of a particular source there are conditions; in fact we must know the black and the white level of the source i.e. :

1.the source in question must be able to generate a white signal, ideally a 100% white (background) full screen pattern

2.the source in question must be able to generate a black signal, ideally a 100 % black (background) full screen pattern

68

 

R5976491 IQ PRO G500 01/02/2007

7. Image Menu

A B

Image 7-27

White balance : In the projector, we will set the contrast for each color until we get a 100% light output picture when projecting a 100% white image (image A)

Black balance : In the projector, we will set the brightness for each color until we get a 0% light output picture when projecting a 100% black image (image B).

The changeover from min to max is indicated by the apparition of bright spots also called “digital noise”

An alternative to a full screen White/black pattern is the standard gray scale pattern, the white bar will be used for white balance and the black bar for black balance.

Image 7-28

Black balance

1.Press MENU to activate the Toolbar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select Input balance

5.Press → to pull down the menu

6.Use ↓ or ↑ to select Black balance (image 7-29)

7.adjust the red black level on a minimal value (image 7-30, image 7-31)

8.adjust the blue black level on a minimal value

Note: this minimal value is not necessary , provided that the 2 other colors are not influencing too much the color to be adjusted, in fact the aim is to minimize the effect of the two other colors since there is a risk of reaching too soon the 50% transition due to the contribution of these two other colors signals.

9.Adjust the green black level until bright spots appear on the screen

10.adjust the blue black level on a minimal value

Note: this minimal value is not necessary , provided that the 2 other colors are not influencing too much the color to be adjusted, in fact the aim is to minimize the effect of the two other colors since there is a risk of reaching too soon the 50% transition due to the contribution of these two other colors signals.

11.Adjust the green black level until bright spots appear on the screen

12.Adjust the Blue black level until bright spots appear on the screen

13.Adjust the red black level until bright spots appear on the screen

the projected image should know be noisy full black

R5976491 IQ PRO G500 01/02/2007

 

69

 

7. Image Menu

Image 7-29

Image 7-30

Image 7-31

Performing White input balance

1.Connect the source you want to project

2.Select a white pattern (or gray scale as alternative)

3.Press MENU to activate the Toolbar

4.Press → to select the Image item

5.Press ↓ to Pull down the Image menu

6.Use ↑ or ↓ to select Input balance

7.Press → to pull down the menu

8.Use ↓ or ↑ to select White balance (image 7-32)

9.adjust the red white level (gain) on a minimal value (image 7-33)

10.adjust the blue white level (gain) on a minimal value

Note: this minimal value is not necessary , provided that the 2 other colors are not influencing too much the color to be adjusted, in fact the aim is to minimize the effect of the two other colors since there is a risk of reaching too soon the transition (bright spots) due to the contribution of these two other colors signals.

11.Adjust the Green white level (gain) until bright spots appear on the screen

12.Adjust the Blue white level (gain) until bright spots appear on the screen

13.Adjust the Red white level (gain) until bright spots appear on the screen

the projected image should know be noisy neutral grey.

70

 

R5976491 IQ PRO G500 01/02/2007

 

7. Image Menu

Image 7-32

Image 7-33

if one uses a gray scale pattern, the bright spots should appear in the white bar.

Selecting Preset restores the factory input balance setting

Remark on the input balance of a component video source

Before starting the Input Balance procedure, generate a signal with dominant white parts.

Input balance is also available for a component video source under following conditions:

A component video signal is present on the BNC’s

”Data on BNC’s” is selected in the Source selection menu

Cr/Y/Cb is selected in the Advanced menu of the corresponding image file

The procedure is the same as for a data source except:

R5976491 IQ PRO G500 01/02/2007

 

71

7.Image Menu

The white balance happens only on Green Adjust until bright spots appear in the image

Image 7-34

The black balance happens on the three colors

The PR and PB connector have to be removed from the input Adjust until noise appears in the image

Image 7-35

The input balance settings are stored in the image file, each source has its own input balance.

7.9AGC on Video

AGC

Automatic Gain Control: allows an automatic amplitude (gain) control of the incoming video signal

AGC is only for Video signals

Enabling/disabling the AGC

1.Press MENU to activate the Tool bar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select AGC on Video

5.Press → to pull down the menu

6.Use ↓ or ↑ to enable or disable the AGC

7.Press ENTER

A white bullet shows the active setting (image 7-36)

72

 

R5976491 IQ PRO G500 01/02/2007

 

7. Image Menu

Image 7-36

The AGC can be disturbing in case of Macrovision encoded signals, therefore the AGC can be disabled (OFF) at any time

7.10 Manual Gain Control

What can be done ?

Beside the AGC there is the possibility to manually set the gain of the incoming video signal. When the AGC is enabled (ON), the manual setting does not affect the gain, AGC must therefore be disabled. The manual gain control must be done on an external pattern with white areas (grey scale bar pattern)

How to set the Manual Gain Control ?

1.Press MENU to activate the Tool bar

2.Press → to select the Image item

3.Press ↓ to Pull down the Image menu

4.Use ↑ or ↓ to select Manual Gain Control (image 7-37)

5.Press ENTER

A scroll bar is displayed (image 7-38)

6.Use ← or →, the numeric keys on the remote, or the keypad to change the gain so as to obtain homogene white parts in the image.

Image 7-37

R5976491 IQ PRO G500 01/02/2007

 

73

7. Image Menu

Image 7-38

74

 

R5976491 IQ PRO G500 01/02/2007

8. Tools Menu

8. TOOLS MENU

Overview

Introduction to PiP

PiP select

PiP add window

PiP remove window

PiP layout

PiP Adjust

Diagnostics

8.1Introduction to PiP

PiP

PiP stands for "Picture in Picture" and allows to display multiple windows containing each of them an image. The windows may be of the video or data type.

What are the different possibilities within the PiP mode ?

The input section of the IQ projector allows a multitude of combinations of different input signals which may be projected in the 4 windows of the PiP screen.

The PiP mode allows independent settings for each window:

Image settings : contrast, brightness, tint, color,...

Vertical and horizontal shift of each window all over the screen

Resizing of the window

Digital Zoom

Linking of (an) audio input(s) to a single or multiple windows

R5976491 IQ PRO G500 01/02/2007

 

75

8. Tools Menu

What are the different PiP layouts ?

Full screen2

The full screen is used to display one of the selected sources.

Browsing through the sources is possible with the PiP Adjust button on the remote.

2–by-2raster2

The screen is divided into 4 subscreens containing 2 Video and 2 Data sources.

Image 8-1

PiP: 2by2 layout

PiP layout 1–33

These are factory layouts, they can be edited and saved.

Personal layouts

Beside the 2 fixed layouts and the 3 factory layouts, one can set 5 additional (personal) layouts.

PiP dedicated buttons

PiP Adjust : this button allows to focus on one particular window, this is shown with a white frame surrounding the selected window.

A source identification box is displayed in the right lower corner.

Image 8-2

Pressing the button removes the frame to the next window. This can also be done via PiP Adjust in the Tools menu

PiP: this button allows to browse through the different configurations, it has the same function asPiP select in the Tools menu.

Since there is only one decoder (second decoder is optional), when in 2by2 configuration, Video1 and Video2 are derived from the same video source.

2.fixed layout

3.factory layouts

76

 

R5976491 IQ PRO G500 01/02/2007

8. Tools Menu

8.2PiP select

PiP layouts

The different PiP layouts (configurations) can be selected in the PiP select menu.

How to change the PiP configuration ?

1.Press MENU to activate the Tool bar

2.Press → to select the Tools item

3.Press ↓ to Pull down the Tools menu

4.Use ↑ or ↓ to select PiP select

5.Press → to pull down the menu

6.Use ↑ or ↓ to select the desired configuration

7.Press ENTER

A white bullet shows the active layout (image 8-3)

Image 8-3

The PiP configuration can also be selected via the dedicated PiP key on the RCU.

8.3PiP add window

What can be done ?

It is possible to add a window to the existing windows (maximum 4), therefore a source must be selected.

Sources which are already used are non selectable. If, for instance, the PiP layout contains a component video then component video will be non selectable.

Once added, the window may be altered in several ways to meet particular needs:

repositioning

re-sizing

changing the order

How to add a window ?

1.Press MENU to activate the Tool bar

2.Press → to select the Tools item

3.Press ↓ to Pull down the Tools menu

4.Use ↑ or ↓ to select PiP add window (image 8-4)

5.Press ENTER

The source selection menu is displayed (image 8-5)

In the lower part of the screen appears a wizard in 4 steps (image 8-6)

R5976491 IQ PRO G500 01/02/2007

 

77

 

8. Tools Menu

Image 8-4

Image 8-5

Image 8-6

8.4PiP remove window

How to remove a window ?

1.Press MENU to activate the Tool bar

2.Press → to select the Tools item

3.Press ↓ to Pull down the Tools menu

4.Use ↑ or ↓ to select PiP remove window (image 8-7)

5.Press ENTER

In the lower part of the screen appears a wizard. (image 8-8)

The selected window appears surrounded with a white frame, each hit on PiP ADJUST will move the frame along the different windows.

Image 8-7

78

 

R5976491 IQ PRO G500 01/02/2007

8. Tools Menu

Image 8-8

8.5PiP layout

Overview

PiP Save

PiP rename layout

PiP delete layout

8.5.1PiP Save

What can be done ?

The active layout can be saved or "saved as".

When a new layout is saved it is added to the PiP select menu.

A fixed layout can be edited (re-sizing,re-positioning,...)but it can not be saved under its original name.

How to save a layout ?

1.Press MENU to activate the Tool bar

2.Press → to select the Tools item

3.Press ↓ to Pull down the Tools menu

4.Use ↑ or ↓ to select PiP layout

5.Press → to pull down the menu

6.Use ↑ or ↓ to select PiP save orsave as (image 8-9)

7.Press ENTER

If save as has been selected, a dialog box is displayed(image 8-10)

Use ← or →, the numeric keys on the remote, or the keypad to enter the name and exit with BACK orMENU. Ifsave as has been selected, a message box is displayed(image 8-11)

Image 8-9

Image 8-11

Image 8-10

R5976491 IQ PRO G500 01/02/2007

 

79

8. Tools Menu

8.5.2PiP rename layout

What can be done ?

The non fixed layouts (factory and personal layouts) can be renamed .

The maximal length of the name is 12 characters.

A fixed layout can not be renamed

How to rename a layout ?

1.Press MENU to activate the Tool bar

2.Press → to select the Tools item

3.Press ↓ to Pull down the Tools menu

4.Use ↑ or ↓ to select PiP layout

5.Press → to pull down the menu

6.Use ↑ or ↓ to select Rename

7.Press ENTER

A dialog box is displayed (image 8-12)

8.Use ↑ or ↓ to select the layout to be renamed

9.Press ENTER

A dialog box is displayed (image 8-13)

Use ← or →, the numeric keys on the remote, or the keypad to enter the name and exit with BACK orMENU.

Image 8-13

Image 8-12

8.5.3PiP delete layout

What can be done ?

The non fixed layouts (factory and personal layouts) can be deleted.

The fixed layouts and the active layout can not be deleted

How to delete a layout ?

1.Press MENU to activate the Tool bar

2.Press → to select the Tools item

3.Press ↓ to Pull down the Tools menu

80

 

R5976491 IQ PRO G500 01/02/2007

 

8. Tools Menu

4.Use ↑ or ↓ to select PiP layout

5.Press → to pull down the menu

6.Use ↑ or ↓ to select Delete

7.Press ENTER

A dialog box is displayed (image 8-14)

8.Use ↑ or ↓ to select the layout to be renamed

9.Press ENTER

The layout is deleted and disappears from the dialog box

Image 8-14

8.6PiP Adjust

What can be done ?

PiP adjust allows to browse through the windows in the active layout, a white frame indicates the window which has the focus. This way, independent settings (picture settings, ...) are possible for each window.

This can also be done by using the dedicated PiP Adjust key on the RCU

Image 8-15

PiP adjust in case of 2by2 layout

AData1 window has the focus, new settings will only affect Data1 window

BVideo1 window has the focus, new settings will only affect Video1 window

PiP adjust

1. Press MENU to activate the Toolbar

R5976491 IQ PRO G500 01/02/2007

 

81

8.Tools Menu

2.Press → to select the Tools item

3.Press ↓ to Pull down the Tools menu

4.Use ↑ or ↓ to select PiP Adjust (image 8-16)

5.Press ENTER

The menu dissapears.

The focus moves to the next window when pressing ENTER (clockwise rotation) If you pressBACK or if you wait 5 seconds the menu is displayed.

Image 8-16

When using the PiP adjust key on the RCU the corresponding source box is displayed in the bottom right corner.

How to adjust a window in the layout ?

1.Use the PiP Adjust key or function in the menu to choose the window to be adjusted

2.Press ENTER

A wizard bar is displayed in the bottom of the screen Follow the procedure.

8.7Diagnostics

What can be done ?

The I2C bus allows the diagnostic of different hardware components

How to display the diagnostics menu ?

1.Press MENU to activate the Toolbar

2.Press → to select the Tools item

3.Press ↓ to Pull down the Tools menu

4.Use ↑ or ↓ to select Diagnostics

5.Press → to pull down the menu

6.Press ENTER to select I2C(image 8-17)

A textbox is displayed (image 8-18, image 8-19)

82

 

R5976491 IQ PRO G500 01/02/2007

8. Tools Menu

Image 8-17

I2C diagnostics

Device Slave address

fpga backplane1 fpga backplane2 fpga backplane3 ADC layer1 ADC layer2 ADC layer3

Serial eeprom DVI layer2 Serial eeprom DVI layer3 Video decoder

Video indicator Video Processor Motor driver Lamp driver

Image 8-18

Image 8-19

R5976491 IQ PRO G500 01/02/2007

 

83

8. Tools Menu

84

 

R5976491 IQ PRO G500 01/02/2007

9. Signal Menu

9. SIGNAL MENU

Overview

Switching mode

Background

9.1Switching mode

Switching from one source to another

To minimize undesired effects when switching from one source to another, one can use the Seamless switching mode, beside Seamless switching there is a wide choice of several effects which render the source switching transitions more enjoyable.

How to select a switching mode ?

1.Press MENU to activate the Tool bar

2.Press → to select the Signal item

3.Press ↓ to Pull down the Signal menu

4.Use ↑ or ↓ to select Switching mode

5.Press → to pull down the menu

6.Use ↑ or ↓ to select the desired switching mode (image 9-1)

7.Press ENTER

A white bullet shows the active effect.

The next source switching will be done using the selected effect

Image 9-1

The Random mode will select a new switching mode at each source switching i.e. there will never be 2 successive source switchings with the same effect.

The Seamless switching mode is not used in the Random mode.

The switching effects are only possible in the full screen mode

R5976491 IQ PRO G500 01/02/2007

 

85

9. Signal Menu

When the source switching mode is the fade in/out mode, the audio (when available) switching will also be done using a fade in/out effect.

9.2Background

Purpose

If there is no signal connected to the projector, the background will be a logo, a black or a blue screen depending on the background settings.

How to change the background ?

1.Press MENU to activate the Toolbar

2.Press → to select the Signal item

3.Press ↓ to Pull down the Signal menu

4.Use ↑ or ↓ to select Background

5.Press → to pull down the menu

6.Use ↑ or ↓ to select the desired background (image 9-2)

7.Press ENTER

Image 9-2

The logo display is only possible in the full screen mode, a logo can thus not be displayed (rescaled) in a window in the PiP mode.

When there is no signal connected, the projector will also start its standby timer countdown (if enabled) and shuts down after the predetermined time.

86

 

R5976491 IQ PRO G500 01/02/2007

10. Lamp Menu

10. LAMP MENU

Overview

Runtimes

Mode

Power mode (only active in the iQG/R 500)

History

Reset runtime

Runtime warning

10.1Runtimes

How to display the lamp runtimes ?

1.Press MENU to activate the Toolbar

2.Press → to select the Lamp item

3.Press ↓ to Pull down the Lamp menu

4.Use ↑ or ↓ to select Runtimes (image 10-1)

5.Press ENTER

A textbox is displayed (image 10-2)

Image 10-1

Image 10-2

10.2 Mode

What are the different lamp modes ?

Single mode

R5976491 IQ PRO G500 01/02/2007

 

87

10. Lamp Menu

The projector will always switch to the lamp with the shortest runtime when the difference between the runtimes of lamp1 and lamp 2 reaches 100 hours, switching from one lamp to another happens only at switching on of the projector and not during operation.

When the lamp fails or reaches its maximum runtime the projector switches automatically to the other lamp without interrupting the projection.The failure is logged and the lamp will never be initialized in the future.

Image 10-3

Single mode operation: switching principle

Dual mode

Both lamps are working.

When one lamp fails, the projector continues the projection using the remaining lamp.

How to select the lamp mode ?

1.Press MENU to activate the Toolbar

2.Press → to select the Lamp item

3.Press ↓ to Pull down the Lamp menu

4.Use ↑ or ↓ to select Mode

5.Press → to pull down the menu

6.Use ↑ or ↓ to select the desired background (image 10-4)

7.Press ENTER

A bullet shows the active mode.

88

 

R5976491 IQ PRO G500 01/02/2007

 

10. Lamp Menu

Image 10-4

When switching from the dual mode to the single mode the lamp with the longest runtime is switched off.

If the runtimes are equal (if the projector has always been operated in dual mode) then lamp1 is switched out.

When switching to single mode, returning to the dual mode will not be possible in the first 60 seconds, Dual in the menu is greyed out and LED1 is flickering, thereby preventing hot restrike which may damage the lamp.

10.3 Power mode (only active in the iQG/R 500)

What can be done ?

The lamp power mode can be chosen to be in :

Full power mode : the total available power is used for the lamps (maximal brightness). This corresponds with the shortest lamp lifetime (1500 hours)

Economy mode : the lamps are dimmed, the lifetime is extended to 3000 hours

The choice of the Power mode must be done during the installation of the projector. The switching between the 2 modes can only be done 6 times and this only during the first 100 hours of the lamp lifetime (considering a dual lamp mode i.e. both lamps are used).

 

 

 

 

Lamps

 

 

 

 

replacement

 

 

 

 

 

Power Mode Switching

 

 

 

 

 

 

 

 

 

 

possible (max 6 times ! )

0

Power Mode Switching

 

 

 

 

Runtime (hours)

100

1500 (Full power mode)

possible (max 6 times ! )

 

 

 

or

 

 

 

 

3000 (econmy mode)

Image 10-5

Lamp power mode (projector considered to be running in dual lamp mode i.e. with both lamps on)

Above considerations and numbers (lifetimes) are only valid when functioning in dual lamp mode (both lamps on)

How to select a Power mode ?

1.Press MENU to activate the Tool bar

2.Press → to select the Lamp item

3.Press ↓ to Pull down the Lamp menu

4.Use ↑ or ↓ to select Power Mode

5.Press → to pull down the menu

6.Use ↑ or ↓ to select the desired mode (image 10-6)

7.Press ENTER

R5976491 IQ PRO G500 01/02/2007

 

89

 

10. Lamp Menu

A dialog box is displayed. Confirm or cancel with Accept orCancel (image 10-7)

Image 10-6

Image 10-7

10.4 History

How to view the history ?

1.Press MENU to activate the Tool bar

2.Press → to select the Lamp item

3.Press ↓ to Pull down the Lamp menu

4.Use ↑ or ↓ to select History (image 10-8)

5.Press ENTER

A textbox is displayed (image 10-9)

Image 10-8

90

 

R5976491 IQ PRO G500 01/02/2007

10. Lamp Menu

Image 10-9

10.5 Reset runtime

When to reset the lamp runtime ?

The lamp runtime should only be reset when placing a new lamp.

WARNING: Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized technician.

How to reset the lamp runtime in the iQ/iD ?

1.Press MENU to activate the Tool bar

2.Press → to select the Lamp item

3.Press ↓ to Pull down the Lamp menu

4.Use ↑ or ↓ to select Reset runtime

5.Press → to pull down the menu

6.Use ↑ or ↓ to select the lamp to be reset (image 10-10)

7.Press ENTER

A dialog box is displayed (image 10-11)

8.Use ←or →, the numeric keys on the remote, or the keypad to change the serial number of the lamp (serial number 0000000 will not be accepted).

Image 10-10

R5976491 IQ PRO G500 01/02/2007

 

91

10. Lamp Menu

Image 10-11

WARNING: Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized technician.

How to reset the lamp runtime in the SIM5Plus?

1.Press MENU to activate the Tool bar

2.Press → to select the Lamp item

3.Press ↓ to Pull down the Lamp menu

4.Use ↑ or ↓ to select Reset runtime

5.Press → to pull down the menu

6.Use ↑ or ↓ to select the lamp to be reset

7.Press ENTER

A dialog box is displayed (image 10-12)

8.Use ←or →, the numeric keys on the remote, or the keypad to change the serial number of the lamp (serial number 0000000 will not be accepted).

Image 10-12

WARNING: Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized technician.

10.6 Runtime warning

What can be done ?

When the lamp has reached a certain predetermined runtime , a warning message will be displayed on the screen. The lamp runtime warning can be set in a range from 30 to 200 hours. The runtime warning is displayed by default at 30 hours before end of lamp lifetime.

92

 

R5976491 IQ PRO G500 01/02/2007

10. Lamp Menu

How to set the lamp runtime warning?

1.Press MENU to activate the Toolbar

2.Press → to select the Lamp item

3.Press ↓ to Pull down the Lamp menu

4.Use ↑ or ↓ to select Runtime warning (image 10-13)

5.Press ENTER

A dialogbox is displayed (image 10-14)

6.Use ←or →, the numeric keys on the remote, or the keypad to change the runtime warning setting.

Image 10-13

Image 10-14

WARNING: Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized technician.

R5976491 IQ PRO G500 01/02/2007

 

93

10. Lamp Menu

94

 

R5976491 IQ PRO G500 01/02/2007

11. Image files menu

11. IMAGE FILES MENU

Overview

Load file

Auto Image

Edit file

Rename file

Copy

Delete

Forced file load

11.1Load file

How to load a file ?

1.Press MENU to activate the Tool bar

2.Press → to select the Image files item

3.Press ↓ to Pull down the Image files menu

4.Use ↑ or ↓ to select Load (image 11-1)

5.Press ENTER

A dialog box is displayed (image 11-2)

6.Use ↑ or ↓ to select the desired file

Tip: For more info about the available image files and the specifications,see "Standard Image Files", page 177

7.Press ENTER

The file is loaded and the image is adapted.

Image 11-1

R5976491 IQ PRO G500 01/02/2007

 

95

11. Image files menu

Image 11-2

In PiP mode, the files which may be loaded will be of the data type if the active window is a data window, or they will be of the video type if the active window is a video window.

What to do if the image is not perfect ?

If the displayed image is not correct after AutoImage or after selecting the best fitting file, go to the Edit menu, select the active file and change the settings.

11.2 Auto Image

What can be done ?

Auto Image creates the best suited image file for the connected source.

It calculates/measures several source parameters :

Total pixels per line

Start pixel

Phase

Contrast/Brightness levels

Auto Image works only for data images.

The measure of the total number of pixels per line can be done through 2 methods

Limited scan: a windowing is used to allow fast tracking. The operation takes about 20 seconds (depending on file)

Full scan: tracking is done over the full range.

The operation takes about 1.5 minutes (depending on file)

How to launch Auto Image?

1.Press MENU to activate the Tool bar

2.Press → to select the Image files item

3.Press ↓ to Pull down the Image files menu

4.Use ↑ or ↓ to select Auto Image

5.Press → to open the menu

6.Use ↑ or ↓ to select the desired file scan method (image 11-3)

7.Press ENTER

96

 

R5976491 IQ PRO G500 01/02/2007

 

11. Image files menu

A text box showing a progress bar is displayed. (image 11-4)

Tip: Press theCancel button to cancel the operation.

Image 11-3

Image 11-4

The Auto Image setup in the Display setup menu affect only Auto Image if it is launched via the RCU key or at automatic file creation.

Launching AutoImage via the menu involves complete checking of all parameters.

Auto Image can also be launched via the RCU with the dedicated AutoImage key.

11.3 Edit file

What can be done with the Edit file menu ?

The Edit file menu makes it possible to change the settings of the file according to the real settings of the connected source. Consult the source specifications before entering the data.

How to edit a file ?

1.Press MENU to activate the Tool bar

2.Press → to select the Image files item

3.Press ↓ to Pull down the Image files menu

4.Use ↑ or ↓ to select Edit (image 11-5)

5.Press ENTER

A dialog box is displayed

6.Use ↑ or ↓ to select the desired file

Note: If in PiP mode the cursor is placed by default on the active file which has the focus.

7.Press ENTER

A dialog box is displayed (image 11-6)

8.Press ENTER

R5976491 IQ PRO G500 01/02/2007

 

97

 

11. Image files menu

A dialog box is displayed (image 11-7)

9.Use ←or →, the numeric keys on the remote, or the keypad to edit and change the values, confirm with ENTER

Note: greyed out fields can not be updated (total pixels)

Image 11-5

Image 11-6

Image 11-7

Which items can be adjusted ?

The following items can be adjusted :

Active horizontal pixels

Horizontal start in pixels

Horizontal period in ns

Active vertical lines

Vertical start in lines

98

 

R5976491 IQ PRO G500 01/02/2007

11. Image files menu

Advanced video settings

Image 11-8

The advanced button enables the advanced settings for a video source.

video signal

frame blanking

video signal

egalisation

HI

Image 11-9

HI AGC Hold interval

The Comb filter is by default enabled.

The AGC hold interval is the time interval in which the AGC is inhibited (AGC hold = no update in video amplitude measurement), the advanced parameter allows to choose a short or long hold interval.

A long AGC hold interval eliminates Macrovision® disturbances since the AGC is hold during a long interval, thus reducing the probability to encounter a Macrovision® pulse.

The sync locking setting is recommended for poor video signals (ex: poor TV signals).

Sharpness adjustment can be chosen to be coarse or fine.

It is recommended to use the default values.

Advanced Data settings

The advanced button enables the advanced settings for a data source.

R5976491 IQ PRO G500 01/02/2007

 

99

11. Image files menu

video info

a b

Hs

 

Hs

 

Image 11-11

Hs horizontal sync pulse a active low

b active high

Image 11-10

The VCO range setting determines the frequency range of the VCO (Voltage Controlled Oscillator).

The Cpmp (Charge pump current) sets the low pass filter current.

Both VCO range & Cpmp are set by the image file, changing these settings is only indicated in for special purposes.

The horizontal sync polarity setting can be useful in case of a bad shaped edge, one can choose between the leading (active low) or trailing (active high) edge.

The input format settings are used to "tell more" about the signals connected on the BNC’s, it completes the information in the source selection menu.

-RGB is selected by default and means that an RGB signal is connected to the BNC’s

-PR/Y/PB must be selected whenever:

a progressive signal (32 kHz frequency video signal ) is connected to the BNC’s (select the source with Data on BNC’s in the Source selection menu).

one wants (in PiP mode) to visualize the component video signal in a Data window hereby adding a video image in the PiP layout.

-HDTV-PR/Y/PBfor high definition component video signals.

It is recommended to use the default values.

11.4 Rename file

How to rename a file ?

1.Press MENU to activate the Tool bar

2.Press → to select the Image files item

3.Press ↓ to Pull down the Image files menu

4.Use ↑ or ↓ to select Rename (image 11-12)

5.Press ENTER

A dialog box is displayed (image 11-13)

6.Use ↑ or ↓ to select the desired file

7.Press ENTER

A text box is displayed (image 11-14)

Use ←or →, ↓ or ↑ the numeric keys on the remote, or the keypad to edit and change the values, confirm with ENTER.

100

 

R5976491 IQ PRO G500 01/02/2007

 

11. Image files menu

Image 11-12

Image 11-14

Image 11-13

11.5 Copy

How to copy a file ?

1.Press MENU to activate the Tool bar

2.Press → to select the Image files item

3.Press ↓ to Pull down the Image files menu

4.Use ↑ or ↓ to select copy (image 11-15)

5.Press ENTER

A dialogbox is displayed (image 11-16)

6.Use ↑ or ↓ to select the desired file

7.Press ENTER

A text box is displayed (image 11-17)

Use ←or →, ↓ or ↑ on the remote, or the keypad to enter the new name, confirm with ENTER.

R5976491 IQ PRO G500 01/02/2007

 

101

 

11. Image files menu

Image 11-15

Image 11-17

Image 11-16

If the AutoImage function does not succeed in finding a file and no file is loaded (load list is empty), which means that the source is not displayed, then use the copy function: Copy a standard file (.std) which is not too different of the source to display, then edit this file to get the best image.

11.6 Delete

How to delete a file ?

1.Press MENU to activate the Tool bar

2.Press → to select the Image files item

3.Press ↓ to Pull down the Image files menu

4.Use ↑ or ↓ to select delete (image 11-18)

5.Press ENTER

A dialog box is displayed (image 11-19)

6.Use ↑ or ↓ to select the desired file

7.Press ENTER

The selected file is deleted and is removed from the list

102

 

R5976491 IQ PRO G500 01/02/2007

 

11. Image files menu

Image 11-18

Image 11-19

11.7 Forced file load

What can be done ?

Forced file load allows to force or lock one particular custom file to be loaded for one particular input. This way one can guarantee that the same desired file is always used for a particular source.

For each layer (layer 1, layer 2, layer 3) we can enable or disable the forced file load. The specification for the file to be selected for each input on that layer is done via RS232.

see the RS232 User Guide for more information on the Forced file load command to be sent.

How to set a file to be loaded ?

1.Press MENU to activate the Tool bar

2.Press → to select the Image files item

3.Press ↓ to Pull down the Image files menu

4.Use ↑ or ↓ to select Forced file load

5.Press → to open the menu (image 11-20)

6.Use ↑ or ↓ to select the desired layer

7.Press ENTER

Forced file load is activated for this layer (this is shown with a bullet)

R5976491 IQ PRO G500 01/02/2007

 

103

 

11. Image files menu

Image 11-20

104

 

R5976491 IQ PRO G500 01/02/2007

12. Display setup

12. DISPLAY SETUP

Overview

Full screen representation

Startup screen

Textbox

Take screenshot

Menu bar position

Status bar position

Sliderbox position

AutoImage Setup

Blanking

12.1Full screen representation

Purpose of the Full screen representation

The Full screen representation function forces to use the complete native resolution of the LCD panels independently of the native resolution of the source.

Note that the full screen representation does not preserve the aspect ratio of the source, i.e. when the aspect ratio of the active image is not the same as the projector (in this case 1920/1080 or 1.77:1), the image will end to be distorted (stretched or shrinked).

How to enable/disable the full screen representation ?

1.Press MENU to activate the Tool bar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Full screen representation

5.Press → to pull down the menu

6.Use ↓ or ↑ to select ON or OFF

7.Press ENTER

The full screen representation will not guarantee the best image quality, therefore the Show native resolution has to be selected.

The show native resolution function on the other hand forces to use the native resolution of the source. TheFull screen representation function overrules theshow native resolution function.

The aspect ratio setting is greyed out when enabling the full screen representation.

12.2 Startup screen

What can be done ?

When the startup screen is enabled, the identification screen is displayed for a few seconds at startup. This startup screen can also be disabled.

R5976491 IQ PRO G500 01/02/2007

 

105

12. Display setup

Image 12-1

How to enable/disable the Startup screen?

1.Press MENU to activate the Tool bar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Startup screen

5.Press → to pull down the menu

6.Use ↓ or ↑ to select the ON or OFF

7.Press ENTER

12.3Textbox

What can be done ?

The textbox function allows to display or not the different sliderboxes used for instance for picture settings (contrast,...), it also affects the source information windows (displayed in the right lower corner of the screen).

How to enable/disable the Textbox ?

1.Press MENU to activate the Toolbar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Textbox

5.Press → to pull down the menu

6.Use ↓ or ↑ to enable/disable the textbox

7.Press ENTER

12.4Take screenshot

What can be done ?

A screenshot can be taken from an active projected image. This screenshot is then saved in a 4 MB RAM and can be used as background.

Each new screenshot erases the previous logo therefore a warning message is displayed asking the user to confirm.

106

 

R5976491 IQ PRO G500 01/02/2007

12. Display setup

Image 12-2

Default (factory stored) Logo

How to take a screenshot ?

1.Press MENU to activate the Tool bar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Take screenshot (image 12-3)

5.Press ENTER

A dialog box is displayed. Press yes to confirm.(image 12-4)

A text box shows the evolution of the operation. (image 12-5,image 12-6)

Image 12-3

Image 12-4

Image 12-5

Image 12-6

R5976491 IQ PRO G500 01/02/2007

 

107

12. Display setup

12.5 Menu bar position

What can be done ?

The menu toolbar can be centered vertically , the range being from top of the screen to the middle of the screen. This can be useful in applications where the top image content is not displayed.

How to center the menu ?

1.Press MENU to activate the Toolbar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Menu bar position menu (image 12-7)

5.Press ENTER

6.Use ↑ or ↓ to position the menu toolbar

Image 12-7

12.6 Status bar position

What can be done ?

The status bar (wizard menu) can be centered vertically , the range being from bottom of the screen to the middle of the screen. This can be useful in applications where the bottom image content is not displayed.

How to center the menu ?

1.Press MENU to activate the Toolbar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Status bar position (image 12-8)

5.Press ENTER

6.Use ↑ or ↓ to position the status bar

108

 

R5976491 IQ PRO G500 01/02/2007

 

12. Display setup

Image 12-8

12.7 Sliderbox position

What can be done ?

The sliderbox can be displayed anywhere on the screen, the position can be set in this menu.

How to reposition the sliderbox?

1.Press MENU to activate the Tool bar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Sliderbox position (image 12-9)

5.Press ENTER

A sliderbox is displayed. Use the 4 arrow keys to drag the box to the desired position. (image 12-10)

Image 12-9

Image 12-10

There is a coarse and a fine adjustment of the position, use ENTER (when sliderbox is displayed) to switch between the two.

R5976491 IQ PRO G500 01/02/2007

 

109

12. Display setup

12.8 AutoImage Setup

What can be done ?

Autoimage allows to detect automatically the characteristics of the source (total pixels per line,...) and uses this information to adapt the image to the LCD panels.

Autoimage can adapt the image based on following data :

Total pixels per line

Start pixel

Phase

Contrast/brightness levels

Autoimage works only for data signals.

How to set up AutoImage?

1.Press MENU to activate the Tool bar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select AutoImage setup (image 12-11)

5.Press ENTER

A dialog box is displayed. (image 12-12)

6.Use the arrow keys to select the desired item and press ENTER to activate or disactivate the item.

Image 12-11

Image 12-12

How to perform AutoImage ?

1.Press AutoImage on the RCU

A textbox showing a progress bar is displayed.

110

 

R5976491 IQ PRO G500 01/02/2007

12. Display setup

During the AUTOIMAGE measuring process the data source disappears temporarily (logo is displayed if background is set to logo )

12.9 Blanking

What can be done ?

The image can be blanked in several ways :

Top blanking

Bottom blanking

Left blanking

Right blanking

Image 12-13

Note that here the blanking is only done on the display i.e. the setting is not saved in the image file. in other words only one type of blanking (setting) can be done independently of the source.

How to blank the image ?

1.Press MENU to activate the Toolbar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the menu

4.Use ↑ or ↓ to select Blanking (image 12-14)

5.Press ENTER

A slider box is displayed (image 12-15)

6.Use ←or →, the numeric keys on the remote, or the keypad to change the blanking.

R5976491 IQ PRO G500 01/02/2007

 

111

 

12. Display setup

Image 12-14

Image 12-15

Use the checkboxes to enable/disable the blanking Use the Reset key to reset the blanking values.

The logo is also affected by the blanking

112

 

R5976491 IQ PRO G500 01/02/2007

13. Installation menu

13. INSTALLATION MENU

Overview

Lens adjustments

Projector address

Orientation

Language

Quick access keys

RS232 baudrate

Automatic startup

Security

Change password

Gemini installed (only for GEMINI CADWALL systems ! )

13.1Lens adjustments

What can be done ?

Motorized lenses can be adjusted in the installation menu or via the dedicated keys on the remote.

The following parameters can be adjusted:

Zoom

Focus

Shift (also for non motorized lenses)

How to Zoom/focus or shift ?

1.Press MENU to activate the Toolbar

2.Press → to select the Installation

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Lens adjustment (image 13-1)

5.Press ENTER

A textbox appears on the screen, follow the instructions. (image 13-2,image 13-3)

Image 13-1

R5976491 IQ PRO G500 01/02/2007

 

113

13. Installation menu

Image 13-2

Image 13-3

13.2 Projector address

What can be done ?

The projector is shipped with projector address set to ”0”

In some cases the projector address must be changed, for example if an unique RCU is used to control 2 or more projectors (independently).

In the OSD menu Projector Address, the following addresses can be programmed :

Projector address: address defined by the user, may be from 0 to 255

0-9is used for RCU communication,0–255being used for RS232 serial communication.

Common address : address may be 0 or 1

How to change the projector’s RC5 address ?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Projector address (image 13-4)

5.Press ENTER

A dialog box appears on the screen. (image 13-5,image 13-6)

Image 13-4

114

 

R5976491 IQ PRO G500 01/02/2007

13. Installation menu

Image 13-5

Image 13-6

Entering the new projector address ?

1. Enter the new projector address with the digit keys on the RCU, the local keypad or the cursor keys.

This address must be between 0 and 255.

How to change the common RC5 address ?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Projector address

5.Press ENTER

A dialog box appears on the screen.

Entering the new common address ?

1. Enter the new projector address with the digit keys on the RCU, the local keypad or the cursor keys.

This address must be between 0 or 1.

13.3 Orientation

Projector orientations

Depending on how the projector is oriented, the projector’s internal settings have to be adapted.

How to change the orientation ?

1.Press MENU to activate the Toolbar

2.Press → to select the Installation item

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Orientation

5.Press → to pull down the menu

6.Use ↓ or ↑ to select the desired orientation (image 13-7)

7.Press ENTER

The projection is adapted and a black bullet shows the active configuration.

R5976491 IQ PRO G500 01/02/2007

 

115

 

13. Installation menu

Image 13-7

13.4 Language

List of languages

The list of selectable languages is depending on the software of the projector.

How to change the Language ?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation item

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Language

5.Press → to pull down the menu

6.Use ↓ or ↑ to select the desired language (image 13-8)

7.Press ENTER

The language is adapted and a black bullet shows the active configuration.

Image 13-8

116

 

R5976491 IQ PRO G500 01/02/2007

13. Installation menu

13.5 Quick access keys

What can be done ?

The 3 function keys on top of the RCU can be associated with a particular item in one of the menus.

Each function which is not password protected or does not have a key on the RCU can be associated to a function key.

How to get an overview of the quick access keys ?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Quick access keys (image 13-9)

5.Press ENTER

A text box appears on the screen.

Image 13-9

How to program the quick access keys ?

1.Scroll through the menus to the desired menu item

2.Push the desired function key for 3 seconds (image 13-10)The menu item is stored in the quick access key

 

F 1

F 2

 

 

F 3

 

 

 

 

 

M EN U

 

B A C K

Image 13-10

Factory pre-programmedfunctions

-F1 :color depth

-F2 :noise reduction-F3 :orientation

R5976491 IQ PRO G500 01/02/2007

 

117

13. Installation menu

13.6 RS232 baudrate

How to change the baudrate?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation item

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select RS232 baudrate (image 13-11)

5.Press → to pull down the menu

6.Use ↓ or ↑ to select the desired baudrate

7.Press ENTER

Image 13-11

13.7 Automatic startup

What can be done ?

The automatic startup allows immediate restart of the projector after a power failure (breakdown), i.e. without passing through the standby state.

The projector restarts at power resume and recovers the previous settings (previous source,...).

This function can be disabled if undesired or inadequate for safety reasons, etc.

CAUTION: If the Automatic startup function is enabled one must be aware of the fact that it involves safety precautions

Make sure that the projector (or the operators!) will not be affected by altered environmental conditions when restarting at power resume.

How to enable/disable the Automatic startup?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation item

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Automatic startup

5.Press → to pull down the menu

6.Use ↓ or ↑ to enable/disable the automatic startup

7.Press ENTER

118

 

R5976491 IQ PRO G500 01/02/2007

 

13. Installation menu

13.8 Security

What can be done ?

A security function is implemented in the projector and allows a protection against theft.

A PIN code allows the user to lock the projector in case of wrong code entry.

The PIN code must be entered at each start up (Power ON), entering three times a wrong number triggers a wait cycle of 15 minutes,

the second 3 wrong codes a wait cycle of 30 minutes, 1 hour, ...

The security mode can be enabled or disabled.

How to activate the security mode ?

1.Press MENU to activate the Tool bar

2.Press → to select the installation item

3.Press ↓ to Pull down the menu

4.Use ↑ or ↓ to select Security (image 13-12)

5.Press → to open the menu

6.Use ↑ or ↓ to select ON

7.Press ENTER

A dialog box is displayed (image 13-13)

8.Use the arrow keys to select YES and press ENTER to confirm A dialog box is displayed

Enter your name, company name,... (this information is displayed in the identification menu) (image 13-14)

9.Press ACCEPT

A dialog box is displayed.

Enter the PIN code, and confirm it. (image 13-15)

An informative text box is then displayed. Press ENTER orBACK to escape.(image 13-16)

Image 13-12

R5976491 IQ PRO G500 01/02/2007

 

119

13. Installation menu

Image 13-13

Image 13-15

Image 13-14

Image 13-16

How to disable the security mode ?

1.Press MENU to activate the Tool bar

2.Press → to select the installation item

3.Press ↓ to Pull down the menu

4.Use ↑ or ↓ to select Security

5.Press → to open the menu

6.Use ↑ or ↓ to select OFF

7.Press ENTER

120

 

R5976491 IQ PRO G500 01/02/2007

 

13. Installation menu

A dialog box is displayed

8.Enter your PIN code

The security mode is now disabled

13.9Change password

How to change the password ?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation item

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Change password (image 13-17)

5.Press ENTER

A dialog box is displayed. (image 13-18)

6.Use ← or → , the numeric keys on the remote , or the keypad to enter and confirm the new password. Each character is displayed as an asterisk.

Image 13-17

Image 13-18

The new password is accepted if the new password and the confirmed password coincide.

If the password is forgotten contact a Barco authorized technician.

R5976491 IQ PRO G500 01/02/2007

 

121

13. Installation menu

13.10 Gemini installed (only for GEMINI CADWALL systems ! )

When to enable ?

Gemini is option is necessary when the iQ is used in a Gemini 2 channel CADWALL system. By enabling Gemini the restrictions relative to the allowed difference in the number of total lines are changed :

1 line for non interlaced sources (instead of 0)

2 lines for interlaced sources (instead of 1)

The default setting is NO. Never activate this option if not in presence of a Gemini CADWALL system.

How to enable Gemini ?

1.Press MENU to activate the Toolbar

2.Press → to select the Installation item

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Gemini installed (image 13-19)

5.Use ↑ or ↓ to select ON

6.Press ENTER

The Gemini option is enabled

Image 13-19

122

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

14. IQ NETWORK

LAN

Local Area Network

WAN

Wide Area Network

Overview

Network architecture

Network functionality

iQ Pro Server specifications

Getting started

Control

Management & diagnostics

Configuration

DropZone

The Web client

14.1Network architecture

SBC

Single Board Computer,

GUI

Graphic User Interface

Topology

The network centric projector (iCon and iQPro) uses an integrated PC (SBC) and can be connected to a LAN. The projector performs the role of Server while each PC is declared as a Client within the system.

Each client PC has to be configured (projector IP address, ...), see “Configuring the client software”

R5976491 IQ PRO G500 01/02/2007

 

123

14. IQ Network

A : SERVER

RM : Remote control &

M2 : Meeting room

 

Management

 

 

P : projection area

V : streaming video data

LAN

WAN

M3 : Large conference room

M1 : Meeting room 1

R : remote meeting attendee

Image 14-1

Typical iQ Pro network architecture

A server

RM Remote Control and Management

M1 Meeting room 1

M2 Meeting room 2

M3 Large screen conference room

P Projection area

R Remote meeting attendee

V Streaming Video data

Wireless LAN (point-to-point)is also possible (using the PCMCIA connection on the projector ) and complements the functionality of direct cabling.

14.2 Network functionality

What can be done ?

The network functionality allows the projector to perform several network functions thanks to network features which are required in most corporate environments:

Control & Management : wireless/wired (remote) control and monitoring of the projector(s) thanks to auser-friendlyGUI (the Client software).

Diagnostics : diagnostics through auser-friendlyGUI and automaticE-mailsending.

Easy file (MS PowerPoint,...) manipulation and projection using the DropZone interface.

Remote control of the projector by allowing the desktop to be shared over the network (theDropZone interface).

Streaming media : The projector’s onboard computer is streaming video data ready, i.e. allowing the decoding of video streaming data coming from a server via the LAN.

124

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

The network centric projector may be configured in the same way as a standard PC to support :

- SNMP service : provides diagnostics, basic control via SNMP messaging

-Microsoft Exchange services: for scheduling of projector tasks.

-Web client : offers an alternative to the Client software through a user-friendlyinternet based interface (includes almost the same features as the Client software)

See the Appendix “General guidelines on Network configuration” for general guidelines on how to enable these services.

14.3 iQ Pro Server specifications

Specifications of the iQ Pro Server platform

1.2 GHz Pentium III processor 4

256 MB RAM

40 GB Hard Disk storage

Microsoft XP Operating System

Barco Server Software for network communication between iQ Pro Server and clients

14.4Getting started

Overview

Connections

Installing the software

Start up of the iQ Pro Server

Configuring the client software

Configuring the Server software

The installation of the iQ Pro in a Local Area Network must be done in the same way as the installation of a standard PC in that particular network meaning that the same rules and accepted practice should be respected.

The assistance of qualified IT personnel is advised.

CAUTION: Important !

A Virus protection program should be installed and kept up to date to prevent virus infections.

CAUTION: The maintenance of the Server must be done in the same way as a PC meaning that the same rules and accepted practice should be respected.

Backups should be taken on a regular basis.

In the same way virus updates should be done regularly.

Barco will not be held responsible for destroyed information in case of a hard disk breakdown or virus infection and has no obligation to pay for or reimburse for the cost of recovering data.

4. the pentium III socket is upgradeable

R5976491 IQ PRO G500 01/02/2007

 

125

14. IQ Network

14.4.1 Connections

Front plate (Layer 3) layout

D

PC CARD

10/100 Base-T

MIC IN LINE IN OUT

USB

 

A B C

Image 14-2

iQ Pro front plate (network layer)

Aaudio connections : mic input, line input, output

B4 x USB connection

CRJ45 connector for network connection

DPCMCIA slot

How to connect the Single Board Computer ?

1.Use the RJ45 connector to connect the SBC to the installed network

2.Use the USB ports to connect peripherals such as mouse, keyboard,... (image 14-3)

Note: Keyboard access duringpre-operatingsystem boot (to access BIOS or F8 key to get operating system select menu) is only supported on the bottom USB input connector next to the Ethernet connector

3.Use the PCMCIA slot to connect a Wireless LAN card or other optional inputs like Bluetooth, Modem cards,...

The slot is protected from dust by a slot door, open the slot door to insert a card.

Note: recommended card type:

-Thecard should be a type II card.

-Thecard should be WindowsTM XP compatible

4.Use the Audio connectors to connect an audio source or microphone, the output allows to use an external audio peripheral such as an amplifier etc.

Image 14-3

126

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

Point to point configuration

B

A

Image 14-4

In case of a temporary configuration (demo purposes) one can use the point to point configuration, the connection being done via RJ45 connections using a crossed UTP cable.

14.4.2 Installing the software

An Administrator password has been installed for security reasons (worm and virus protection):

Password : Barco (case sensitive !)

Necessary parts

installation CD (delivered)

PC

How to install the client software ?

1. Install the client software from the CD ( Setup file )

How to install the server software ?

1.The server software is by default installed on the projector. if necessary, reinstall it from the CD.

The CD containing the server software and the client tools are delivered with the projector. They can always be downloaded from the secured PartnerZone Web site : https://secure.barco.com/presentation/

14.4.3 Start up of the iQ Pro Server

Starting up

There are 2 methods to start up the iQ Pro Server

Manual start up (via the General menu)

Automatic startup at projector startup: this is done by defining the state of the iQ Pro Server during a “Projector ON state” and a“Projector standby state” .

Manual start up: How to start up/shut down/reset the iQ Pro Server ?

1.Press MENU to activate the Toolbar

2.Press → to select General

3.Press ↓ to Pull down the General menu

4.Use ↑ or ↓ to select iQ Pro Server

5.Press → to open the menu

6.Use ↑ or ↓ to select ON/OFF/Reset (image 14-5)

7.Press ENTER

R5976491 IQ PRO G500 01/02/2007

 

127

 

14. IQ Network

Image 14-5

When resetting the PC the menuitems in the iQ Pro Server menu are greyed out during a short period.

Projector Standby state setting

This setting defines what should happen with the iQ Pro Server when the projector is switched to standby. The iQ Pro Server can stay in the ON state or it can be switched OFF

Projector On state setting

This setting defines what should happen with the iQ Pro Server when the projector is switched on.

The iQ Pro Server can stay OFF (switching on can then happen manually in the general menu) or it can be switched on (at the same time as the projector)

Automatic start up: How to set the automatic startup ?

1.Press MENU to activate the Toolbar

2.Press → to select Installation

3.Press ↓ to Pull down the menu

4.Use ↑ or ↓ to select iQ Pro Server settings

5.Press ENTER

6.A dialogbox is displayed (image 14-6)

7.Select ONfor the “Projector On state”setting

The iQ Pro Server will now be automatically switched on at the next startup of the projector

Image 14-6

The iQ Pro Server will be switched on but not necessarily selected by default, go to Source selection in the menu to select the iQ PC.

128

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

14.4.4 Configuring the client software

The same universal client interface is used for different network centric projectors (iQ, iD, iCon). The layout of the interface (position of the controls,...) is adapted after detection of the projector type. Some screenshots may not fully coincide with the reality.

How to start up the client software ?

1.Start up the previously installed client program

The interface shows 3 tabs (upper tab control ): Control, Diagnosis and Configuration The active sub interface is the control sub screen (image 14-7)

2.Click on the upper menubar to select the desired sub interface

Image 14-7

Control interface

IP

Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.

How to add a projector to the projector list

1.Click on the white arrow (image 14-8)A menu is dropped down(image 14-9)

2.click on the + sign of the projector list A dialog box is displayed (image 14-10)

3.Fill in the Name, the IP address (optional) and the Port number of TCP/IP connection

Note: default port number = 9999

4.Fill in the alias

Tip: “Alias” is a custom name whereas “Name” is the name by which the projector is identified on the (corporate) network

5.Click OK to confirm orCancel

The projector is now added to the list of projectors

R5976491 IQ PRO G500 01/02/2007

 

129

 

14. IQ Network

Image 14-8

Image 14-10

Image 14-9

projector list: contains a projector and a projector group sub list

Depending on the installed network (use of DHCP server or not), the IP address may be needed to be entered or not.

For a point to point installation the projector’s IP address must be entered manually.

Check the operating system on the for the IP address, or contact your IT administrator.

How to add a projector group to the projector group list ?

1.Click on the white arrow

A menu is displayed, image 14-9

2.Click on the + sign of the projector group list A dialog box is displayed (image 14-11)

3.Fill in the group name

4.Click OK to confirm or Cancel

The group is now added to the list of groups

130

 

R5976491 IQ PRO G500 01/02/2007

 

14. IQ Network

Image 14-11

How to add projectors to a group ?

1.Click on the projector to be added in the projector list

2.Drag the projector down to the projector group. The projector is added to the group.

Adding a projector to a group can also be done by using the “Copy + Paste” method on the right mouse button menu.

How to connect to a projector or group of projectors ?

1.Double click on the projector or group of projectors

A green dot appears, indicating that the projector is present on the network and working properly (image 14-12)

The name of the projector or group is now displayed in the upper part of the screen and indicates that the communication has been set (image 14-13)

Image 14-12

connected and active projector

A connected and active projector

Image 14-13

A connected and active projector

When connected to a group of projectors, some controls may be disabled.

In general, controls will only be selected if this is the status of all projectors in the group.

Sliders will be set to a particular value only if this is the same on all projectors in the group, otherwise they will be positioned centrally with a dash in the value box. When the slider is moved the box will show the new value and this value will be sent to all projectors in the group.

Labels such as Current Source in the general page will only be shown if the string value is the same on all projectors, otherwise a dash will be shown

The Target information block

The target information block displays the main characteristics of the connected projector or group of projectors. This gives also an indication whether the communication setting has been successful or not.

R5976491 IQ PRO G500 01/02/2007

 

131

 

14. IQ Network

Image 14-14

14.4.5 Configuring the Server software

Internal network connection

The internal connection ( firmware connection) between the projector controller and the single board computer uses fixed IP addresses.

The IP address of the SBC can be found in control panel

SBC: IP address = 192.168.42.51, subnet mask = 255.255.255.248

Projector Controller’s IP address = 192.168.42.50

Image 14-15

132

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

Image 14-16

Image 14-17

CAUTION: Leave these IP addresses unchanged !

The server menu

The server menu can be opened by right clicking from the server tray icon

R5976491 IQ PRO G500 01/02/2007

 

133

 

14. IQ Network

Image 14-18

Start Meetings control

The meeting control is started and positioned on the desktop, through out the meeting it will allow to :

Accept requests interactively : a request for a desktop sharing from a client PC must be accepted on the iCon server, a dialog box is displayed on the iCon asking to accept or decline the desktop sharing request

Deny all requests : all request are denied

Accept all requests automatically : desktop sharing is always accepted at the iCon (server) without prompting for confirmation

Notify end of meeting at : allows to set a reminder at expected end time of the meeting

Image 14-19

How to configure the Server settings ?

1.Go to the server icon in the lower task bar of the desktop and click the right mouse button. A menu is displayed

2.Select Settings

A dialog box is displayed allowing to select different tabs

-Networking

-Dropzone, see Dropzone chapter

-Exchange

134

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

Networking settings

Image 14-20

Port settings: it is advised to leave these settings in their default value.

Mail to field : see mail configuration in the client software

SNMP enable: allows to enable the SNMP control of the projector.

The Enable write option allows to enable the client to overwrite projector settings via SNMP.

Unchecking this option means that projector settings will only be read.

Exchange settings

This tab allows to fill in the exchange parameters to allow scheduling of projector tasks.

These parameters should be configured by your local IT administrator

Image 14-21

Miscellaneous settings

This tab allows following settings :

R5976491 IQ PRO G500 01/02/2007

 

135

 

14.IQ Network

Enable password protection : when using a password, one must enter it when starting up the client interface

Automatically open sole document ... : when using a USB stick, the document is automatically opened (only when one document present).

When using a password, the control via the previous V1.1 client version will not be possible therefore disable password protection. Note that using a previous client version in combination with V1.2 server is indicated with following text box :

Image 14-22

client-serversoft incompatibility

Image 14-23

To check the server version open the about menu from the tray

Image 14-24

136

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

14.5 Control

Overview

Description

How to use the control manager?

General

The source selection screen

The PiP screen

Image settings

Advanced control

14.5.1 Description

What can be done ?

The projector allows a software client (client PC) to communicate locally with the server and hereby control the projector’s settings, in this case one has a point to point communication,image 14-25. The client PC or laptop communicating with the projector may be locally installed or may be remote, communication may then happen over a LAN,image 14-26

The projector performs the role of Server while the PC acts as a Client within the system.

The control and management client software incudes the possibility to create groups of projectors and that way control a whole fleet of projectors.

B

A

Image 14-25

point to point iQ Pro network communication

Afacility manager’s desk

Bprojector area

A : facility manager's desk

B : projection areas

...

LAN

Image 14-26

control & management of network centric projector(s)

Afacility manager’s desk

Bprojector area

What can be controlled ?

Almost every menu item can be controlled through the control manager

R5976491 IQ PRO G500 01/02/2007

 

137

14.IQ Network

standby on/off

lamp mode

source selection

switching effects

background setting

all PiP settings (layout, window)

Image settings

lens adjustments

The control manager

The control interface in the client software is divided into 5 subscreens, image 14-27:

General

source selection

PiP

image settings

advanced

Image 14-27

The control interface: the general sub screen is active (see tool bar)

14.5.2 How to use the control manager?

How to use the control manager?

1.Choose the sub screen by clicking on the desired item on the tool bar in the upper part of the control interface The active sub screen is indicated with a blue spot

14.5.3General

What can be done ?

Basic controlling, monitoring and general parameter setting of the projector can be done in this screen, image 14-27.

3 buttons ON,STANDBY andPAUSE

The target information part gives the main characteristics of the projector

2 buttons allow to switch between dual and the single lamp mode

How to change the general settings?

1.Click on the lamp mode button to select the desired mode A blue spot indicates the active mode

2.Click on one of the three buttons to start up, pause or put in standby the projector A green led indicates the status of the projector.

138

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

14.5.4 The source selection screen

What can be done ?

A source selection dialog box allows to visualize all the sources or only the detected sources.

3 buttons to activate, freeze, pause and logo

selection of 12 different switching effects

selection of 3 different backgrounds: logo, Blue, Black

Image 14-28

The source selection screen

How to select a source ?

1.Click on show allor show detected

Depending on the option (show all/detected) selected, a list is displayed.

In case show all is selected, a list of all possible sources is displayed, signal presence is indicated with an orange dot.

When show detected is selected, all the detected sources are displayed with an orange dot.

2.Double click on the desired source The selected source is now projected

In group mode there are only grey or green nodes, no orange (detected).

On start up, a green node will be shown when all projectors are playing the same source type.

Grey will be shown when some of the projectors are not showing the same source type.

If we double click on a grey node, it should go green as long as at least one of the projectors in the group can show the source.

14.5.5 The PiP screen

Following screenshots are taken for an iQPro projector. The layouts may be slightly different for an iCon (layout automatically adapted after projector type detection by the client).

What can be done ?

The PiP tool allows to manage the PiP of the projector in a more user friendly way:

a check box list allows to choose between 10 PiP layout (5 preset layouts and 5 personal layouts)

several buttons allow operations on windows (add, remove ) as well as on the PiP layouts (save, ...)

a graphical screen allows easy altering of the PiP layout : re sizing, positioning of the different windows.

R5976491 IQ PRO G500 01/02/2007

 

139

14. IQ Network

Image 14-29

PiP screen

How to perform operations on a PiP layout

As an example, let us choose a personal (non preset) layout, add a window, reposition the windows, and save the layout under a different name.

1.Click on one of the check boxes to choose a layout Choose a personal layout (image 14-30)

The PiP screen (as well as the projected layout) is updated (image 14-31)This layout contains one window being an RGBHV Data source

2.Click on the Add window button

Note: if the layout already contains 4 window, it will be impossible to add a new one. In that case a window is displayed,image 14-32

A dialog box is displayed showing the possible sources to be added. (image 14-33)

3.Select the source to be linked to the new window. The window is added to the layout. (image 14-34)

4.When entering the PiP screen the cursor is replaced by a hand, Click on the window to be repositioned. The window is surrounded by a white frame.

5.Drag the window to the desired position.

6.Place the cursor on one of the corners of the window to be re sized. A double arrow is displayed.

7.Drag to re size.

Note: the window is re sized by keeping the same aspect ratio.

140

 

R5976491 IQ PRO G500 01/02/2007

 

14. IQ Network

Image 14-30

Image 14-31

Image 14-32

Image 14-33

Add window dialog box

Image 14-34

Importing/exporting a layout

Every PiP layout can be exported and saved as backup on the network or on the hard disk of the Client PC. It can then be imported at any time.

R5976491 IQ PRO G500 01/02/2007

 

141

 

14. IQ Network

How to import/export a layout ?

1.Click on the Export button.

A dialog box is displayed. (image 14-35)

2.Browse to the desired location and fill in the filename.

Image 14-35

How to import a layout ?

1.Click on the import button.

A dialog box is displayed. (image 14-36)

2.Select the layout to be imported.

Image 14-36

For more information on Picture in Picture see the PiP chapter.

14.5.6 Image settings

What can be done ?

General settings

Color temperature

Geometry

General image settings

1.Click on Image settings menu in the tool bar to drop down the submenu(image 14-37)

2.Click on General

142

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

3. Slide the cursors to set the corresponding value (image 14-38)

Image 14-37

Image 14-38

Use the checkbox to define a coarse or a fine setting.

Click on the Filmmode button to enable or disable the filmmode.

Color temperature preset settings

1.Click on Image settings menu in the tool bar to drop down the submenu.

2.Click on color temp,image 14-37

3.Click on the desired preset color temperature. (image 14-39)

Image 14-39

Custom color temperature setting

1.Click on the Custom button.

A dialog box is displayed. (image 14-40)

2.Use the sliders to set the red and the blue color temperature.

R5976491 IQ PRO G500 01/02/2007

 

143

14. IQ Network

Image 14-40

Geometry settings

1.Click on Image settings menu in the tool bar to drop down the submenu.(image 14-41)

2.Click on Geometry.

a dialog box is displayed. (image 14-42)

3.Use the buttons to zoom or pan.

Tip: Use the buttons to choose small, medium or large adjustment steps.

Each click changes the setting.

4. Click on the desired aspect ratio and resolution handling mode.

Image 14-41

Image 14-42

14.5.7 Advanced control

Overview

Lens adjustments

Options

144

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

14.5.7.1 Lens adjustments

How to adjust the lens ?

1.Click on the Advanced menu in the tool bar to drop down the submenu

2.Click on lens adjustments (image 14-43)

3.Use the buttons to shift/zoom/focus the lens (image 14-44)

Tip: Use the buttons to choose small, medium or large adjustment steps.

Each click changes the setting.

Image 14-43

the Advanced control submenu

Image 14-44

14.5.7.2 Options

How to start up the options menu ?

1.Click on the Advanced menu in the tool bar to drop down the submenu.

2.Click on Options . Seeimage 14-45.

R5976491 IQ PRO G500 01/02/2007

 

145

14. IQ Network

Image 14-45

The advanced Options screen

How to set up and perform AutoImage ?

1.Check the boxes corresponding to the desired setting of AutoImage. (image 14-46)

2.Click on Apply to perform AutoImage.

Image 14-46

Lamp runtime warnings startup settings

1.Fill in the lamp runtime warning time. (image 14-47)

2.Click on startup screen to enable the startup screen.

3.Click on Auto Startup to enable automatic startup.

Image 14-47

A blue spot indicates that the function is enabled.

146

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

14.6 Management & diagnostics

14.6.1 Description

What can be done ?

Diagnosis of a projector or a group of projectors is possible through on line monitoring. Mail services are also available and allow the client to be periodically informed about status errors and warnings concerning the different components of the projector.

What can be diagnosed/checked ?

projector’s general parameters as type, serial number, embedded SW version,...

advanced diagnostics of the projector on board/component level: fpga, decoder,...

user defined critical components (by E-mailfeedback, seeE-mail configuration)

14.6.2 Diagnostics manager

How to start up ?

1. Click on diagnostics in the main tool bar

How to check the general diagnostics ?

1.Click on general to view the general diagnostics Seeimage 14-48.

Image 14-48

general diagnostics screen

How to check the advanced diagnostics ?

1.Click on advanced to view the advanced diagnostics See image 14-49.

R5976491 IQ PRO G500 01/02/2007

 

147

14. IQ Network

Image 14-49

advanced diagnostics screen: green = OK ; red = error

14.7 Configuration

14.7.1 E-mailmessaging

What can be done ?

E-mailmessaging allows the projector to generate automaticallyE-mailand send them to three configurable recipients.

The mail can be sent on a regular basis i.e. daily, weekly or monthly or can be triggered by warnings.

Basically two different configurations must be done:

content

timing

Content configuration

The content configuration allows to define the content of the E-mail

general content

advanced content

Timing configuration

E-mailsending can be set to be time dependent or status dependent

daily : E-mailis sent every day, the time can be set

weekly: the day can be set with a calendar

on warning : a E-mailis sent whenever a warning is generated by the projector

14.7.2 E-mailconfiguration

How to configure the E-mail?

1.Click on Configuration in the toolbar

2.Click on Mail Config to open the mail configuration screen Seeimage 14-50.

3.set the content by clicking the desired content (image 14-51)

4.set the timing by clicking the desired time interval

Note: if the timing is chosen to be monthly, a calendar is displayed , click the days on which theE-mailshould be sent

148

 

R5976491 IQ PRO G500 01/02/2007

 

14. IQ Network

Image 14-51

Image 14-50

mail configuration screen

Mail “from” configuration

The “from” field of the received mails i.e. the name of the sender (in this case the iQ Pro server) can be configured in the server software.

Therefore the E-mailaddress has to be filled in theNetworking tab of theiQ Control Server properties dialogbox

Image 14-52

14.7.3 Projector Firmware Upgrade

What can be done ?

The client software allows to do an upgrade of the projector’s firmware.

The upgrade is done with a binary file (extension = “.bin”) which is sent to the projector using the LAN connection. Single projector as well as multiple projector (group) upgrade is possible

How to upgrade the firmware ?

1.Click on Configuration in the toolbar

2.Click on Upgrade to open the firmware upgrade screen Seeimage 14-53.

3.Use the Browse key to select the desiredbin file.

R5976491 IQ PRO G500 01/02/2007

 

149

 

14.IQ Network

4.Press the Upgrade button on the browser to select the file to start the operation(image 14-54)

5.Press the Upgrade button on the upgrade screen to start the operation The information screen will show the progress of the operation.

Image 14-53upgrade interface

Image 14-54

If the download doesn’t succeed please contact Barco

150

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

14.8 DropZone

14.8.1 Dropzone tools

What can be done ?

The dropzone interface allows the user to manage (launch, store,...) presentation files from a local desktop.

Image 14-55

the DropZone interface

14.8.2 Start up

Start up

To start using the DropZone one must define the server (projector/display) to connect to. Several situations are possible.

1.The projector/display to connect to has not yet been declared in the DropZone interface, in that case the projector/display has to be added to the DropZone list using the Add function.

2.The projector/display to connect to has already been declared in the DropZone, one must then just selected it from the list. In case the projector/display name is not known, there is a possibility to select the projector.

by its location (only if the location has been specified).

How to open the installation menu ?

1.Click on the arrow to pull down the installation menu. (image 14-56)Seeimage 14-57.

Image 14-56

R5976491 IQ PRO G500 01/02/2007

 

151

14. IQ Network

Image 14-57installation menu

How to add a projector to the list ?

1.Click on the three suspension points to open the projector selection dialog box. (image 14-58)

2.Click on the Add button.

A dialogbox is displayed. (image 14-59)

3.Enter the projector name or browse the network.

4.Click on OK.

5.Enter the Location (optional).

6.Click on Connect.

Following message is displayed : “Connected to <projectorname>...”

Image 14-59

Image 14-58

How to select an existing projector by its name ?

1.Click on the three suspension points to open the projector selection dialog box, image 14-58

2.Open the listbox and select the projector. (image 14-60)

the location will also be filled (if it has been entered previously).

3.Click on Connect.

Following message is displayed : “Connected to <projectorname>...”

Image 14-60

How to select an existing projector by its location ?

Can be useful when the projector name is not known.

1.Click on the three suspension points to open the projector selection dialog box, image 14-58

2.Open the listbox and select the location. (image 14-61)

152

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

The projector name is filled in.

3.Click on Connect.

Following message is displayed : “Connected to <projectorname>...”

Image 14-61

This is only possible if the location has been filled, the default value for location being “<New Location>

If the projector is not found following message will be displayed : “Host not found”

If the projector is found but unable to respond ( projector disconnected from the network, server software not running, ...) following message will be displayed : “ Host found , but server inactive”

14.8.3 File dropping/launching

Only the Microsoft viewers (PPT, Word, Excel,...) are installed on the projector.

File dropping

Dropping a file means sending it to the projector using the DropZone interface.

The projector can then react in different ways depending on the drop mode selected :

launch file

launch file and share

store file on the projector

File launching

Launch files: a file stored on the projector (server) or on the network can be accessed from a local PC (via the network) or from the projector itself. Launching a file means “sending and starting up” a file (using the required software).

A PowerPoint file can be launched on your PC and projected in another place (by default only the PPT viewer is installed on the projector ).

for iQ only : The file will only be projected if the “iQ PC” is selected in the source selection.

How to set the drop mode ?

1.Open the DropZone interface.

2.Click on the arrow to pull down the installation menu.

3.Click on the three suspension points access the drop mode dialog box,image 14-57 Seeimage 14-62.

4.Click on one of the three modes.

R5976491 IQ PRO G500 01/02/2007

 

153

 

14. IQ Network

Image 14-62

How to drop a file using the drag method ?

1.Drag the file into the drop window. (image 14-63)

The window opens and shows now the projector. (image 14-64)

2.release the mouse button.

The projector will then process the file according to the setting of the drop mode.

Image 14-64

Image 14-63

How to drop a file using the Open dialog box ?

1.Click on the upper button.

A browser is displayed. Choose a file to send to the projector.

The projector will then process the file according to the setting of the drop mode.

What to do with the launched files once disconnected ?

The previously dropped files are placed in a local directly on the server, one may choose to delete them or not.

1.Click on the arrow to pull down the installation menu.

2.Click on the Options button.

A dialog box is displayed. (image 14-65)

3.Check the box to destroy the launched files once disconnected.

Image 14-65

154

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

14.8.4 Open remotely a file on the projector

How to open a file on the projector ?

1.Click on the lower button of the DropZone interface

A browser is displayed. Select the file to be projected.

for iQ only: The file will only be projected if the “iQ PC” is selected in the source selection.

14.8.5 Remote desktop sharing (virtual meeting)

What can be done ?

The remote desktop sharing in the DropZone allows to visualize the projected image i.e. the desktop of the projector PC on a local PC.

Besides Desktop sharing one can take theControl (mouse and keyboard control) over a presentation (using NetmeetingTM). The control over the presentation can be taken or passed at any time.

The configuration consisting of several remote or local meeting participants sharing the same information content is called a virtual meeting.

In this virtual meeting each meeting participant can participate to the meeting either in a passive way, by following the meeting on his local desktop (remote desktop sharing), or in an active way by controlling the server’s desktop (mouse and keyboard).

Control over the desktop can be requested, forwarded or released.

R5976491 IQ PRO G500 01/02/2007

 

155

 

14. IQ Network

1

3

3 2

2

1

1

IQ Pro Server desktop Control

2

3

Image 14-66

Virtual Meeting

1forward control

2release control

3request control

How to perform remote desktop sharing ?

1.Click on the middle button

The middle button indicates the activation of the remote

The desktop is displayed on the local PC monitor. (image 14-67)

156

 

R5976491 IQ PRO G500 01/02/2007

14. IQ Network

Image 14-67

remote desktop sharing in case of a PowerPointTM presentation

How to take (mouse and keyboard)Control over the desktop ?

1.Click on the Control menu

The Control menu is displayed(image 14-68)

2.Select the Request Controlitem

The desktop can now be remote controlled.

Image 14-68

The control over the desktop is now done by the local PC. However, the user can at any time decide to release or forward the control to someone else.

How to release control over the desktop ?

1.Click on the Control menu

The Control menu is displayed(image 14-69)

2.Select the Release Controlitem

The desktop remote control can now be requested by someone else.

R5976491 IQ PRO G500 01/02/2007

 

157

 

14. IQ Network

Image 14-69

How to forward control over the desktop ?

1.Click on the Control menu

The Control menu is displayed(image 14-70)

2.Select the Forward Controlitem

A pop up menu shows the meeting participants i.e. the users which are connected to the server and which participate to the

Remote sharing of the desktop.

3.Select the meeting participant

The control is transferred and the user which has the control is know indicated in the title bar.

Image 14-70

14.8.6 DropZone settings

What can be done ?

The Server settings on the Projector allow to configure the DropZone in several ways:

Disallow new meeting participants: New meeting participants will not be able to request desktop sharing or desktop control.

Disallow Launch file: Launching a file with the DropZone will be impossible when activating this setting, hereby preventing undesired content to be projected during a meeting.

Enable/disable desktop sharing at startup or logon.

How to setup the DropZone ?

1.Go to the server icon in the lower task bar of the server desktop and Click the right mouse button. A menu is displayed (image 14-71)

2.Select Settings

3.Select the DropZone tab(image 14-72)

4.Check the desired settings

158

 

R5976491 IQ PRO G500 01/02/2007

 

14. IQ Network

Image 14-71

Image 14-72

 

Choosing True color as color depth setting will slow down the communication.

It is advised to leave the other Server properties as they are. If necessary Contact your IT administrator.

14.9 The Web client

Web based functionality

The aim of the web services is to allow each network client within the LAN environment to browse via its internet browser to the web client.

This may be seen as an alternative to the client software since the main control & diagnostic tools are also present. Its advantage resides in the fact that no software has to be installed on the local PC, the internet takes while the html page generation is done locally on the server.

How to access the web client via the internet browser ?

To access the web client, the http link has to be filled in on the client’s internet browser.

This http link contains the name of the projector/display i.e. the name under which it is identified within the LAN.

R5976491 IQ PRO G500 01/02/2007

 

159

 

14. IQ Network

Image 14-73

Web interface

What can be done ?

The possibilities are mainly the same as on the client software.

The web interface allows a user friendly way to manage the projector/display, its use being straightforward and similar to the client interface (ref).

Requirements for the use of the Web client

Some components have to be installed or enabled on your local (client) operating system to allow access to the Web client.

See the Appendix “ General guidelines on network configuration” for general guidelines on how to enable these services. .

The minimal server software version should be V1.10 to allow the use of the Web client.

160

 

R5976491 IQ PRO G500 01/02/2007

15. General guidelines on Network Configuration

15. GENERAL GUIDELINES ON NETWORK CONFIGURATION

Overview

General Network

The Internet and Web services

The installation of the iQ Pro in a Local Area Network must be done in the same way as the installation of a standard PC in that particular network meaning that the same rules and accepted practice should be respected.

The assistance of qualified IT personnel is advised.

15.1 General Network

An Administrator password has been installed for security reasons (worm and virus protection):

Password : Barco (case sensitive !)

Microsoft NT Domain

To enable access to your network resources, the iQ Pro must be a member of your NT Domain.

This can be configured in the Control Panel, under “System”, in the “Computer Name” tab, under the button “Network ID”. You’ll need some help from the Network Administrator, since you need special rights to do this.

TCP/IP

The iQ Pro uses TCP/IP networking, so it needs the IP address, network mask, broadcast address, gateway, dns, wins, etc. to be configured. This can be done in the Control Panel, under “Network Connections”. This can however be configured automatically, if your network uses DHCP.

15.2 The Internet and Web services

Internet access

If you want to access the Internet from the iQ Pro, and the projector is located behind a firewall, you will also need to configure the proxy to use. This can be done in the Control Panel, under “Internet Options”, in the tab “Connections”, under the button “LAN Settings”.

iQ Pro Web services

To use the iQ Pro web client, you might need to change the “LAN Settings” on your local computer

If the client thinks the projector is on the Internet, and tries to connect to it through the proxy, you can turn on the “Bypass proxy server for local addresses” feature, or add the projector to the Exceptions list under the “Advanced” button.

The “Internet Information Services(IIS) ” component has to be installed on the operating system.

SNMP

To enable management via the IQProSNMP Agent, you must enable the SNMP system service, and configure the communities accordingly.

This can be done in the Control Panel, under Administrative Tools, in the Services, under the entry “Management and Monitoring tools”. You may also need to enable SNMP in the iQ Pro Control Server in de suystem tray, see image below.

R5976491 IQ PRO G500 01/02/2007

 

161

 

15. General guidelines on Network Configuration

Image 15-1system tray

Image 15-2

server settings dialog box

For more info, see "SNMP services", page 171

Microsoft Exchange and Outlook

To enable control via the Microsoft Exchange integration, you need to install, enable and configure the IQProEXCH module.

To enable control from Microsoft Outlook, you need to install, enable and configure the IQProEXCH module, and install an Outlook Form on the Exchange Server in your network.

For more info, see "Exchange", page 163

162

 

R5976491 IQ PRO G500 01/02/2007

A. Exchange

A. EXCHANGE

Introduction

Some parameters values are installation dependent, and are shown here as an example.

You may need assistance from you network administrator, IT Manager or MIS helpdesk to obtain the settings or to configure the projector for you, since this is a task description targeted to ‘Administrators’ and needs knowledge and/or permissions normally held by those persons.

It is advised that you first try to follow the procedure to obtain a working setup, before changing the settings for conforming to your local security requirements.

Use of this software requires a working Microsoft Exchange server installed somewhere in your corporate network.

A.1 Exchange Installation

A.1.1 Installation procedure

Creating a user account and mailbox

1.Create a user account in your NT Domain (on the projector).

The service will use this account to log on to the domain, and as credentials to authenticate to Microsoft Exchange to read the entries in the Calendar folder of the Mailbox.

Username: iqpro Domain: BARCO Password: pwiqpro

2.Create a Mailbox for the projector’s account on the Microsoft Exchange Server (on your LAN). The NT Domain user created in step 1 should have read access to this Mailbox.

Server: “BARCOEXCHSRV”Mailbox: “Projector, IQPRO”User: BARCO\iqpro

Installing and configuring Microsoft Outlook (on the projector)

1.Install Microsoft Outlook on the Projector.

Note: To be able to access Microsoft Exchange, you need a Client Access License.

Once you have one of those, you also have a license to Microsoft Outlook.

Refer to the following URL for more information: http://www.microsoft.com/resources/sam/licensing/cal_guide/exchange.asp

Tip: Outlook can be installed from the Microsoft Exchange Server CDROM or from a Microsoft Office Suite Installation CDROM.

Since the IQ Pro has no CDROM drive, you may need to use a CDROM drive shared from a PC in the network.

Alternatively, you could use a USB CDROM drive.

2.Make sure the projector is part of the domain

Tip: This can be done in ControlPanel->System->ComputerName->Change

3.Log in on the projector as the user User: iqpro

Domain: BARCO Password: pwiqpro

Tip: If the user cannot log on, the Local Administrator should add the right “Log on locally” for the user.

This must be configured in Start->ControlPanel->AdministrativeTools->LocalSecurity Policy

4.Configure Outlook

Profile Name: “MS Exchange Settings”

This is what the wizard proposes by default, and what is used in this document. Default Mail Client: yes

Note: Make sure that MS Outlook is the default Mail Client for this account.

You can do this afterwards from this configuration page: Start->ControlPanel->Internet

Options->Programs->EmailFor more information, refer to :

http://www.microsoft.com/mspress/troubleshooting/outlook/LS/101801.asp

Enabling the account

1. Log on to the projector as an Administrator for the next steps.

R5976491 IQ PRO G500 01/02/2007

 

163

A. Exchange

For security reasons, you will probably not want to make the projector account part of one of the administrator groups.

2.Enable the account to be used by the “iQ Pro Exchange Integration” service

3.In the Tree of the “Local Security Settings” application, navigate to Security Settings->LocalPolicies->UserRight Assignment.

4.In the List, edit the “Log on as a service”, and add the account, in the example “BARCO\iqpro”.

Installing and configuring the iQProEXCH service

Step 1,2,3 refers to the manual installation. One can use the SETUP.EXE program instead.

1.Copy the file IQProEXCH.EXE to (eg.) C:\Program Files\BARCO\iQ Pro Server

2.Open a command line, and go to the that directory

3.Type the following command IQProEXCH /Service

4.To configure, right click the “IQ Pro Server” tray icon, and go to the tab “Exchange” Enter the credentials (image A-1,image A-2)

5.To enable the “IQProEXCH” service go to Control Panel->AdministrativeTools->Services->IQProExchange go to the TAB “General Startup” and Type: Automatic

Make the service use the correct account TAB Log On Select “Local System Account”

Check “Allow service to interact with desktop”

6.Start the service, or reboot the projector.

Image A-1system tray

Image A-2

server exchange tab

You should now be able to schedule commands from a Microsoft Exchange client such as Outlook

running on any computer on the local network, provided you have the necessary permissions on the

Calendar in the projector mailbox.

A.1.2 Troubleshooting

The file C:\Program Files\BARCO\IQ Pro Server\IQProEXCH.log and the “Event Log” may contain helpful information to diagnose what’s going wrong

What can go wrong and what to do ?

1.The log file contains “Logon failure: unknown user name or bad password

Check Username, Password and Domain in Control Server/Exchange

2.The log file contains “Logon failure: the user has not been granted the requested logon type at this computer.” The user account must be given the “Log on as a service” permission. This is done in Start/Control Panel/Administrative Tools/ Local Security Settings/Security Settings/Local Policies/User Right

164

 

R5976491 IQ PRO G500 01/02/2007

A. Exchange

Assignment. In the list, add the user to the entry “Log on as a service

3.The log file contains “Could not log on with Profile ’MS Exchange Settings’” Make sure the profile exists. To check this, log in to the projector as the user (BARCO\iqpro), as the profile should be owned by the projector account, andOutlook-profilesareper-account.Start/Control Panel/Mail

4.The user cannot log on to the projector. The Administrator should add the right “Log on locally” for the user. This must be configured in the Start/Control Panel/Administrative Tools/Local Security Policy

In the list, add the user to the entry “Log on as a service

5.When trying to start the service, the projector beeps, and the service stays in the ‘starting’ state

This happens when the service tries to display an error in a popup, but cannot access the desktop. Control Panel/Administrative Tools/Services/IQPro Exchange

Check “Allow service to interact with desktop

You may need to end the process ‘IQProEXCH’ from the task manager.

6.The commands are not executed at the right time

Check the time of the computer and the timezone Start/Control Panel/Date and Time/Timezone

7.An Outlook dialog box is displayed stating that there is no default mail client.

Make sure that MS Outlook is the default Mail Client for this account. You can do this from this configuration page: Start/Control Panel/Internet Options/Programs/Email

You may need to do this as administrator, since the service is started as ‘Local System’ account.

Tip: For more information, refer to http://www.microsoft.com/mspress/troubleshooting/outlook/LS/101801.asp

A.2 Exchange Integration

Introduction

The projector must be configured to connect to a mailbox on a Microsoft Exchange server in the network, which is dedicated to the projector, and to which of course the projector has rights to connect to.

The commands should be put in the SUBJECT of an appointment in the Exchange Calendar of the projector. The Start Time and End Time of the appointments are used for timing info. The other fields (location, categories, body, … ) are not used by the software, and thus can be used to store extra information for the USERS of the projector mailbox.

A.2.1 Command

How are the commands build up ?

Command filename/filepath

The parameter filename is a filename relative to the “Receive” directory of the iQ Pro Control Server, which, in a default installation, would typically be the local folder “C:\Documents and Settings\All Users\Received” The parameterfilepath is an absolute path to a file.

The commands should be put in the SUBJECT of an appointment in the Exchange Calendar of the projector. This is a mailbox on a Microsoft Exchange server in the network, which is dedicated to the projector, and to which of course the projector has rights to connect to.

The command and the filename are separated by a space.

R5976491 IQ PRO G500 01/02/2007

 

165

A. Exchange

Overview of the commands

ON

STANDBY

PAUSE

PAUSE ON

PAUSE OFF

LOGO

LOGO ON

LOGO OFF

SWITCH SOURCE

SWITCH LAYOUT

LAUNCH ATTACHMENT

STORE ATTACHMENT

STORE filename

STORE FILE filepath

LAUNCH filename

LAUNCH FILE filepath

DELETE filename

DELETE FILE filepath

ON, STANDBY

The projector is put in the specified state at the beginning of this event. Beware that if the SBC (Single Board Computer) is to be powered-downduring STANDBY, that further events will not be processed, since the integration runs on that SBC.

PAUSE, LOGO

The projector is put in the specified state at the beginning of this event, and the state is undone at the end of this event. o A parameter ON or OFF can be specified to choose between the actions. This action will then be executed at the beginning. So “PAUSE from 12:00 to 13:00” is equivalent to “PAUSE ON at 12:00” + “PAUSE OFF at 13:00”

SWITCH SOURCE, SWITCH LAYOUT

The projector switches source or layout at the beginning of this event.

LAUNCH ATTACHMENT

The attachment is saved at the beginning of this event. Then the associated application is started. o At the end of the event, the application is killed. This can not be guaranteed if the application was already running on the projector. For example, if a web page is being displayed, and a second one is launched, the application is not started, but the original browser displays the page. In this case the second event can not control the browser. This is a limitation of the Windows platform.

STORE ATTACHMENT

The attachment is saved at the beginning of this event. The name of the attachment is used and the file is placed in the Receive folder.

STORE filename

The attachment is saved at the beginning of this event. The name filename is used and the file is placed in the Receive folder. For example “STORE MYFILE.PPS” will save the attached file to “C:\Documents and Settings\All Users\Received\MYFILE.PPS”

STORE FILE filepath

The attachment is saved at the beginning of this event. The path filepath is used as absolute filename. For example, the command “STORE FILE C:\My Videos\MYFILE.AVI” will store the attachment as C:\My Videos\MYFILE.AVI. This of course if permissions are correct and the directory C:\My Videos exists

DELETE filename

The file with name filename is deleted from the receive folder. For example “DELETE MYFILE.PPS” will delete “C:\Documents and Settings\All Users\Received\MYFILE.PPS”

DELETE FILE filepath

The file with absolute name filepath is deleted. For example, the command “DELETE FILE C:\My Videos\MYFILE.AVI” will store the attachment as C:\My Videos\MYFILE.AVI.

Drop down list

Besides the above commands some predefined commands can be selected from a drop down list in the iQPro tab.

166

 

R5976491 IQ PRO G500 01/02/2007

A. Exchange

Image A-3

A.2.2 Example

Schedule projector tasks in Microsoft Outlook 2000

following tasks are scheduled:

Image A-4

1.store attachment at 12:30 (The attached file is iQ_Pro_brochure.pdf)

2.turn the projector on at 13:00 and launch a different attached file

3.show the logo from 14:29 to 14:31 to hide the killing of the application and the starting of the PDF Viewer

4.at 14:30, lauch the PDF file that was stored in step 1 5

5.kill the application and put the projector in standby at 16:00

6.delete the PDF file that was stored in step 1

A.2.3 Microsoft Outlook Integration

Adding Outlook forms

To make things easier for users, you can install an Outlook Form that adds a tab called “iQ Pro” to the appointment. The form contains the most-usedcommands ineasy-tousedrop-downlists. It looks as follows:

R5976491 IQ PRO G500 01/02/2007

 

167

 

A. Exchange

Image A-5

The form contains the functionality that a normal user should be able to use without consulting the documentation. The attachments, date and time fields must be edited in the “Appointment” tab.

Choosing items from the drop-downboxes fills in the subject.

By default, the layouts “Full-screen”and “2by2 raster” are defined in the form.

If you add layouts on the projector(s) or change the defaults, the user must type the name of the layout in the subject.

The form can be modified to make things easier for users, one can also add the defined layouts to the drop-downlist. This must be done from Outlook, in the menu“Tools->Forms->DesignThis Form”

Organizational Forms

The administrator should install Organizational Forms on the Exchange Server in the “Organizational Forms” library.

Default form

Now the form still needs to be set as a default for creating new items. When returning to the “Forms” tab in the “Calendar Properties” you should now see the “iQ Pro” template installed. Now go to the “General” tab and select the template as default for posting to the folder.

Image A-6

If the form was installed as an “Organizational Form”, you need to select the “Forms…” entry, which will display the “Choose Form” dialog,

168

 

R5976491 IQ PRO G500 01/02/2007

A. Exchange

Image A-7

A.2.4 Folder form

Folder form

Alternatively, the form can be installed for the Calendar folder only, by following the procedure described below

How to configure a folder form

1.In outlook, right-clickon the “Calendar” icon in the “Outlook Shortcuts” tab in the “Outlook Bar” to open the “Properties” page, whilelogged-onas the projector (Or display the “Folder List”, andright-clickthe “Calendar” folder to open the “Properties” page).

2.In the “Calendar Properties” dialog, go to the “Forms” tab, and click the “Manage…” button. (image A-8)

3.On the “Forms Manager” dialog, click the “Install…” button and select the file “iQ Pro.fdm”. (image A-9)

4.When returning to the “Forms” tab in the “Calendar Properties” you should now see the “iQ Pro” template installed. Now go to the “General” tab and select the template as default for posting to the folder. (image A-10)

Image A-9

Image A-8

R5976491 IQ PRO G500 01/02/2007

 

169

A. Exchange

Image A-10

A.2.5 Limitations and known “problems”

Overlapping tasks

When launching 2 attachments with overlapping times it is possible for the application to exit at the end of the first period. For example, let’s say we try to display PRES1.PPT from 12:00 to 13:30, and PRES2.PPT from 13:00 to 14:30, it is possible for BOTH presentations to exit at 13:30. This is because Windows uses the same process to display both files, and activates them via DDE.

Image A-11

This is a limitation in the Microsoft Windows ShellExecuteEx API

Avoid overlapping schedules in this case, or change the associations in: My Computer->Tools->FolderOp-tions->FileTypes->(extension)

Try to disable DDE (under Edit with the default action, eg ‘open’, selected) and/or disable ‘Browse in same window’ or using a different viewer/player for the file type.

170

 

R5976491 IQ PRO G500 01/02/2007

B. SNMP services

B. SNMP SERVICES

Introduction

Some parameters values are installation dependent, and are shown here as an example.

You may need assistance from you network administrator, IT Manager or MIS helpdesk to obtain the settings or to configure the projector for you, since this is a task description targeted to ‘Administrators’ and needs knowledge and/or permissions normally held by those persons.

It is advised that you first try to follow the procedure to obtain a working setup, before changing the settings for conforming to your local security requirements.

B.1 SNMP installation

Introduction

The Control Server version should be at least version 1.10.

To check the version, open the about box from the server tray:

Software updates can be obtained from the BARCO support website: ftp://ftp.barco.com/pub/iq_pro_software/ or from secured website PartnerZone

How to install SNMP (only if necessary)

1.The Microsoft SNMP service must be installed

You may need to install this service from the Windows XP CDROM.

2.Install the SNMP Agent Extension dll regsvr32 IQProSNMP.dll The agent should now be registered as “iqpro” under

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Parameters\ExtensionAgents

How to configure SNMP (only if necessary)

1.Go to the Control panel, under the Administrative Tools, in the Services, in the “SNMP” entry.

2.In the “General” tab, you can enable the service, and make it start automatically.

3.In the “Security” tab, the default Community is called ‘public’ and is read-only.

You may want to give read-writepermission to ‘public’ (not recommended) or create a ‘private’ community withread-writepermissions.

4.In the Control Server, enable the SNMP support, and optionally, enable read-writesupport.

5.The SNMP service should be restarted, to take the changed settings into account.

To uninstall the snmp agent: regsvr32 /u IQProSNMP.dll

B.2 SNMP integration

Commands

Following commands are provided stored in the MIB :

Command

Type

 

 

PROJECTORTYPE

READ

 

 

SERIALNUMBER

READ

 

 

R5976491 IQ PRO G500 01/02/2007

 

171

B. SNMP services

Command

Type

 

 

LAMPPRODUCTNUMBER

READ

 

 

LAMPSERIALNUMBER

READ

 

 

SERVERTYPE

READ

 

 

SERVERVERSION

READ

 

 

EMBEDDEDSOFTWAREVERSION

READ

 

 

PROJECTORLANGUAGE

READ

 

 

PROJECTORNAME

READ

 

 

LOCATION

READ

 

 

ORIENTATION

READ

 

 

RESOLUTION

READ

 

 

DESKTOPRESOLUTION

READ

 

 

PROJECTORSTATE-cooldown

READ

 

 

PROJECTORSTATE-textbox

READ

 

 

PROJECTORSTATE-projector

READ/WRITE

 

 

PAUSE

READ/WRITE

 

 

FREEZE

READ/WRITE

 

 

PROJECTORRUNTIME

READ

 

 

LAMPWARNINGSTATUS

READ

 

 

LAMPALERTSTATUS

READ

 

 

LAMPMODE

READ/WRITE

 

 

LAMPRUNTIME

READ

 

 

LAMPSTATUS

READ

 

 

LAMPWARNINGTIME

READ/WRITE

 

 

I2CDIAGNOSTICS

READ

 

 

POWERSUPPLYERROR

READ

 

 

LAMPERROR

READ

 

 

PCSTATEPROJECTORON

READ/WRITE

 

 

PCSTATEPROJECTORSTANDBY

READ/WRITE

 

 

PCSTATE

READ/WRITE

 

 

172

 

R5976491 IQ PRO G500 01/02/2007

C. Troubleshooting

C. TROUBLESHOOTING

An Administrator password has been installed for security reasons (worm and virus protection):

Password : Barco (case sensitive !)

FAQ table

This table gives a summary of possible errors, the aim of this section is to give general guidelines and tips for troubleshooting.

C.1 FAQ table

What to do when...

?

 

 

 

 

 

Symptom

 

Possible cause

Check

References

 

 

 

 

 

 

 

The projector is working

 

The Projector ON state

The setting should be

 

(operational mode) but Server

 

is not running

 

 

setting ( in the “iQ Pro

 

“ON”

 

 

 

 

Server settings” menu)

 

 

 

The projector is in standby mode

The Projector Standby

The setting should be

 

and the Server is not running

 

 

 

 

state setting ( in the “iQ Pro

 

“ON”

 

 

 

 

Server settings” menu)

 

 

 

No client/server communication

IP address is not filled in

IP address

 

in case of a point to point

 

communication

 

 

correctly

 

 

 

 

 

 

 

 

 

No client/server communication

Client configuration

Client configuration:

IT administrator

over the LAN

 

 

 

 

 

 

 

projector name

 

When using the DropZone, the iQ

NetmeetingTM settings are

NetmeetingTM settings

IT administrator

Pro server does not accept calls

 

from client(s)

 

 

incorrect

 

 

 

 

 

 

 

 

 

When using the DropZone it is

No access the shared

check guest account

IT administrator

impossible to launch/store files

 

 

 

 

folder “Received”

 

settings in WindowsTM

 

PC card is not working or influences

incompatible PC card

Check if the PC card

IT administrator

the good working of the SBC

 

 

 

 

 

 

driver is compatible with

 

 

 

 

 

 

WindowsTM XP

 

R5976491 IQ PRO G500 01/02/2007

 

173

C. Troubleshooting

174

 

R5976491 IQ PRO G500 01/02/2007

D. Cleaning the dustfilters

D. CLEANING THE DUSTFILTERS

Overview

Dustfilters

Cleaning

D.1 Dustfilters

Location of the filters

There are 4 filters located at different positions

1.Filter1: Lamp 1

2.Filter2 : Lamp 2

3.Filter 3 : X-Cubefilter

4.Filter 4 : Input filter

Image D-1

location of the filters

1lamp filter 1

2lamp filter 2

3x-cubefilter

4input filter

D.2 Cleaning

How to clean the dustfilters ?

1.Place the projector so as to access easily the filter to be cleaned

2.Push the handle downwards to unlock the filter. (image D-2)

3.Slide out the filter (image D-3,image D-4,image D-5)Seeimage D-6.

4.Clean the dust filter with a dry cloth.

5.Re-insertthe dust filter by sliding it back in the filter housing.

Image D-2

Location of the x-cubefilter and its handle

R5976491 IQ PRO G500 01/02/2007

 

175

D. Cleaning the dustfilters

Image D-4

lamp & X-Cubefilters removed

Image D-3

Lamp filter removal

Image D-6

Input filter removed

Image D-5

Input filter removal

If the airflow is falling under a predetermined treshold value a warning will be displayed on the screen.

Image D-7

At that time it is strongly recommended to replace or clean the dustfilter under the X-cube.Failing to do so, will strongly reduce the lifetime of the LCD’s and the analyzers.

The manufacturer reserves itself the right to refuse warranty repair if the projector was working with dirty dustfilters.

176

 

R5976491 IQ PRO G500 01/02/2007

E. Standard Image Files

E. STANDARD IMAGE FILES

E.1 Table overview

Table overview

The following standard image files are pre-programmedin the projector.

Name5

Resolution6

Fvert

FHor

Fpix

Ptot10

Pact11

Ltot12

Lact13

 

 

Hz7

kHz8

MHz9

 

 

 

 

1600_48V

1600x600i

48,040

62,500

135,000

2160

1600

651

600

 

 

 

 

 

 

 

 

 

CGA

640x200i

59,924

15.700

14.318

912

640

262

200

 

 

 

 

 

 

 

 

 

COMPUSC4

1024x480i

29,945

30,694

39,779

1296

1024

512

480

 

 

 

 

 

 

 

 

 

DOS1_70

720x400

70

31,500

28,350

900

720

449

400

 

 

 

 

 

 

 

 

 

DOS3_56

640x400

56

24,800

21,030

848

640

440

400

 

 

 

 

 

 

 

 

 

DOS4_85

640x400

85

37,860

31,500

832

640

445

400

 

 

 

 

 

 

 

 

 

ED

735x480

59,943

31,470

28,638

910

735

525

480

 

 

 

 

 

 

 

 

 

EGA

640x350

59,702

21,851

16,257

744

640

366

350

 

 

 

 

 

 

 

 

 

ESVGA_75

832x624

73

47,900

53,648

1120

832

660

624

 

 

 

 

 

 

 

 

 

EXGA_60

1152x864

60

54,900

79,934

1456

1152

916

864

 

 

 

 

 

 

 

 

 

EXGA_80

1152x864

80,000

76,499

110,159

1140

1152

958

864

 

 

 

 

 

 

 

 

 

EXGA_85

1152x864

85

77,202

121,671

1576

1152

907

864

 

 

,000

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXGA1_70

1152x864

70

63,800

94,424

1480

1152

912

864

 

 

 

 

 

 

 

 

 

EXGA1_75

1152x864

75

67,499

107,999

1600

1152

900

864

 

 

 

 

 

 

 

 

 

EXGA2_70

1152x864

70

66,098

99,941

1512

1152

945

864

 

 

 

 

 

 

 

 

 

EXGA2_75

1152x864

75

75,199

110,092

1464

1152

1002

864

 

 

 

 

 

 

 

 

 

FMR

640x400i

42,323

36,440

28,570

784

640

431

400

 

 

 

 

 

 

 

 

 

GE_50

640x400

50

31,200

44,928

1440

1163

625

522

 

 

 

 

 

 

 

 

 

GE_60

1085x480

60

30,700

41,261

1344

1085

512

480

 

 

 

 

 

 

 

 

 

hd_1080i

1920x540

60

33,750

74,249

2200

1920

563

540

 

 

 

 

 

 

 

 

 

hd_24p

1920x1080

24,000

27,000

74,000

2750

1920

1125

1080

 

 

 

 

 

 

 

 

 

hd_24sf

1950x540

48,000

27,000

74,000

2750

1950

562

540

 

 

 

 

 

 

 

 

 

hd_25i

1920x540

50,000

28,125

74,000

2640

1920

562

540

 

 

 

 

 

 

 

 

 

hd_25p

1920x1080

25,000

28,125

74,000

2640

1920

1125

1080

 

 

 

 

 

 

 

 

 

5.Name: name of file, contains the settings.

6.Resolution: image resolution, when followed by ..i means interlaced.

7.Fvert Hz: vertical frame frequency of the source

8.FHor kHz: horizontal frequency of the source

9.Fpix MHz: pixel frequency

10.Ptot : total pixels on one horizontal line.

11.Pact: active pixels on one horizontal line.

12.Ltot: total lines in one field

13.Lact: active lines in one field.

R5976491 IQ PRO G500 01/02/2007

 

177

E. Standard Image Files

Name5

Resolution6

Fvert

FHor

Fpix

Ptot10

Pact11

Ltot12

Lact13

 

 

Hz7

kHz8

MHz9

 

 

 

 

hd_30p

1920x1080

30,000

33,750

74,000

2200

1920

1125

1080

 

 

 

 

 

 

 

 

 

hd_60p

1280x720

60,000

45,000

74,000

1650

1280

750

720

 

 

 

 

 

 

 

 

 

INTER_GR

1184x886

67,170

61,796

92,941

1504

1184

920

886

 

 

 

 

 

 

 

 

 

IQPC_SXGA_2

1366x1024

59

62,933

106,230

1688

1366

1067

1024

 

 

 

 

 

 

 

 

 

IQPC_SXGA_D

1280x1024

60

63,857

107,791

1688

1280

1063

1024

 

 

 

 

 

 

 

 

 

IQPC_XGA_1

1024x768

61

49,005

65,863

1344

1024

807

768

 

 

 

 

 

 

 

 

 

IQPC_XGA_2

1024x768

60

48,485

65,164

1344

1024

807

768

 

 

 

 

 

 

 

 

 

IQPC_XGA_D

1024x768

61

49,005

65,863

1344

1024

806

768

 

 

 

 

 

 

 

 

 

MAC_3

512x384

60,147

24,480

15,667

640

512

407

384

 

 

 

 

 

 

 

 

 

MAC_4

560_384

60,147

24,480

17,234

704

560

407

384

 

 

 

 

 

 

 

 

 

MAC_5

512x342

60,158

22,259

16,670

704

512

370

342

 

 

 

 

 

 

 

 

 

MAC_6

832x624

74,546

49,722

57,280

1152

832

667

624

 

 

 

 

 

 

 

 

 

MAC_7

1024x768

74,907

60,150

80,000

1330

1024

803

768

 

 

 

 

 

 

 

 

 

MAC_LC

640x480

66,619

34,975

31,338

896

640

525

480

 

 

 

 

 

 

 

 

 

MAC_POR

640x870

74,996

68,846

57,280

932

640

918

870

 

 

 

 

 

 

 

 

 

METH_BOOT1

720x400

70

31,500

28,350

900

720

448

400

 

 

 

 

 

 

 

 

 

METH_BOOT2

640x480

59

31,000

24,800

800

640

524

480

 

 

 

 

 

 

 

 

 

MXGA_100

1152x864

100

92,997

145,820

1568

1152

930

864

 

 

 

 

 

 

 

 

 

NTSC

675x240

60

15,748

13,512

858

675

263

240

 

 

 

 

 

 

 

 

 

NTSC_LIMO_x2

834x482

60

31,496

32,252

1024

834

525

482

 

 

 

 

 

 

 

 

 

NTSC_LIMO_x3

834x715

60

46,646

47,766

1024

834

778

715

 

 

 

 

 

 

 

 

 

NTSC_LIMO_x4

834x961

60

62,992

64,504

1024

834

1050

961

 

 

 

 

 

 

 

 

 

PAL

675x286

50

15,625

13,500

864

675

313

286

 

 

 

 

 

 

 

 

 

PAL_LIMO_x2

834x574

50

31,250

32,000

1024

834

626

574

 

 

 

 

 

 

 

 

 

PAL_LIMO_x3

834x850

50

46,296

47,407

1024

834

926

850

 

 

 

 

 

 

 

 

 

PAL_LIMO_x4

834x1146

50

62,500

64,000

1024

834

1250

1146

 

 

 

 

 

 

 

 

 

PAM500

640x400

60,000

26,400

22,810

864

640

440

400

 

 

 

 

 

 

 

 

 

PAM800

1120x375i

44,936

36,443

50,000

1372

1120

406

375

 

 

 

 

 

 

 

 

 

PC98_2

1120x375i

39,994

32,835

47,840

1457

1120

411

375

 

 

 

 

 

 

 

 

 

PC98_3

1120x750

60,000

50,000

78,569

1571

1120

833

750

 

 

 

 

 

 

 

 

 

S1152_66

1152x900

66,004

61,846

94,500

1528

1152

937

900

 

 

 

 

 

 

 

 

 

S1152_76

1152x900

76,637

71,809

108,000

1504

1152

937

900

 

 

 

 

 

 

 

 

 

178

 

R5976491 IQ PRO G500 01/02/2007

E. Standard Image Files

Name5

Resolution6

Fvert

FHor

Fpix

Ptot10

Pact11

Ltot12

Lact13

 

 

Hz7

kHz8

MHz9

 

 

 

 

S1600_67

1600x1280

67

89,286

200,000

2240

1600

1334

1280

 

 

 

 

 

 

 

 

 

SDI_625

675x278i

25,000

15,625

13,500

864

720

313

278

 

 

 

 

 

 

 

 

 

SDI_525

675x240i

29,970

15,734

13,500

858

720

263

240

 

 

 

 

 

 

 

 

 

SG_50

1600x1200

50,000

62,500

130,313

2085

1600

1250

1200

 

 

 

 

 

 

 

 

 

SG_60_1

1280x1024

60,000

63,900

107,352

1680

1280

1065

1024

 

 

 

 

 

 

 

 

 

SG_60_2

1024x768

60,000

48,780

64,390

1320

1024

813

768

 

 

 

 

 

 

 

 

 

SG_60_3

960x680

60,000

43,200

54,432

1260

960

720

680

 

 

 

 

 

 

 

 

 

SG_60_4

1600x1200

60,000

75,000

156,375

2085

1600

1250

1200

 

 

 

 

 

 

 

 

 

STOR_100

764x287

100

31,300

30,361

970

764

313

287

 

 

 

 

 

 

 

 

 

STOR_120

810x247

119

31,300

30,361

970

810

263

247

 

 

 

 

 

 

 

 

 

STOR_50

1024x512

50

31,300

40,064

1280

1024

625

512

 

 

 

 

 

 

 

 

 

STOR_60

1024x512

60

31,300

40,064

1280

1024

525

512

 

 

 

 

 

 

 

 

 

SUNEWS67

1280x1024

67,189

71,691

117,000

1632

1280

1067

1024

 

 

 

 

 

 

 

 

 

SUNEWS76

1280x1024

76,107

81,130

135,000

1664

1280

1066

1024

 

 

 

 

 

 

 

 

 

SUNXGA60

1024x768

59,984

48,287

64,125

1328

1024

805

768

 

 

 

 

 

 

 

 

 

SUNXGA70

1024x768

70,041

56,596

74,250

1312

1024

808

768

 

 

 

 

 

 

 

 

 

SUNXGA77

1024x768

77,069

62,040

84,375

1360

1024

805

768

 

 

 

 

 

 

 

 

 

SUP_MAC

1024x768

60,000

48,780

63,999

1312

1024

813

768

 

 

 

 

 

 

 

 

 

SVGA_56V

800x600

56,250

35,156

36,000

1024

800

625

600

 

 

 

 

 

 

 

 

 

SVGA_60V

800x600

60,317

37,879

40,000

1056

800

628

600

 

 

 

 

 

 

 

 

 

SVGA_72_1

800x600

72,084

48,080

50,003

1040

800

666

600

 

 

 

 

 

 

 

 

 

SVGA_72_2

800x600

72,084

48,080

50,003

1040

800

667

600

 

 

 

 

 

 

 

 

 

SVGA_75

800x600

75,000

46,875

75,000

1056

800

625

600

 

 

 

 

 

 

 

 

 

SVGA_85

800x600

85,000

53,635

56,250

1048

800

631

600

 

 

 

 

 

 

 

 

 

SXGA_72_1

1280x1024

72

76,699

128,854

1680

1280

1061

1024

 

 

 

 

 

 

 

 

 

SXGA_72_2

1280x1024

72

76,970

130,080

1690

1280

1069

1024

 

 

 

 

 

 

 

 

 

SXGA_75

1280x1024

75

79,974

134,997

1688

1280

1066

1024

 

 

 

 

 

 

 

 

 

SXGA_76

1280x1024

76

81,103

134,955

1664

1280

1066

1024

 

 

 

 

 

 

 

 

 

SXGA_85

1280x1024

85

91,149

157,506

1728

1280

1072

1024

 

 

 

 

 

 

 

 

 

SXGA_L

1280x1024

60

62,500

84,000

1344

1280

1041

1024

 

 

 

 

 

 

 

 

 

R5976491 IQ PRO G500 01/02/2007

 

179

E. Standard Image Files

Name5

Resolution6

Fvert

FHor

Fpix

Ptot10

Pact11

Ltot12

Lact13

 

 

Hz7

kHz8

MHz9

 

 

 

 

SXGA+_60

1280x1024

60

63,980

107,997

1688

1280

1066

1024

 

 

 

 

 

 

 

 

 

SXGA2_60

1280x960

60

59,999

107,998

1800

1280

1000

960

 

 

 

 

 

 

 

 

 

SXGA2_85

1280x960

85

85,940

148,505

1728

1280

1011

960

 

 

 

 

 

 

 

 

 

SXGA50

1280x1024

50

52,351

88,368

1688

1280

1047

1024

 

 

 

 

 

 

 

 

 

SXGA60v

1280x1024

60

63,658

110,001

1728

1280

1056

1024

 

 

 

 

 

 

 

 

 

SXGAP_70

1024x1280

70

92,902

133,779

1440

1024

1326

1280

 

 

 

 

 

 

 

 

 

SXGAP1_60

1024x1280

60

77,700

83,916

1080

1024

1297

1280

 

 

 

 

 

 

 

 

 

SXGAP2_60

1024x1280

60

79,498

110,661

1392

1024

1325

1280

 

 

 

 

 

 

 

 

 

UXGA_60

1600x1200

60

75,002

162,004

2160

1600

1250

1200

 

 

 

 

 

 

 

 

 

UXGA_65

1600x1200

65

81,248

175,496

2160

1600

1250

1200

 

 

 

 

 

 

 

 

 

UXGA_L

1600x1200

60

72,801

119,977

1648

1600

1216

1200

 

 

 

 

 

 

 

 

 

UXGAP1_60

1200x1600

59

95,804

119,946

1252

1200

1620

1600

 

 

 

 

 

 

 

 

 

UXGAP2_60

1200x1600

60

99,404

163,817

1648

1200

1656

1600

 

 

 

 

 

 

 

 

 

VGA_60

640x480

60

31,326

25,061

800

640

525

480

 

 

 

 

 

 

 

 

 

VGA_66

640x480

67

35,100

30,326

864

640

525

480

 

 

 

 

 

 

 

 

 

VGA_72

640x480

73

37,860

31,500

832

640

520

480

 

 

 

 

 

 

 

 

 

VGA_75

640x480

75,000

37,500

31, 500

840

640

500

480

 

 

 

 

 

 

 

 

 

VGA1_85

640x480

85,000

43,369

36,000

832

640

509

480

 

 

 

 

 

 

 

 

 

VGA2_85

720x400

85,000

37,900

35,475

936

720

446

400

 

 

 

 

 

 

 

 

 

VGA75ISO

640x480

75,000

39,375

31,500

800

640

525

480

 

 

 

 

 

 

 

 

 

VIDEO525

1302x239i

29,970

15,734

32,207

1302

1024

263

239

 

 

 

 

 

 

 

 

 

VIDEO625

1024x278i

25,000

15,625

31,984

1310

1024

313

278

 

 

 

 

 

 

 

 

 

XGA_43

1024x384

87

35,500

44,872

1264

1024

409

384

 

 

 

 

 

 

 

 

 

XGA_60

1024x768

60,000

48,360

64,996

1344

1024

806

768

 

 

 

 

 

 

 

 

 

XGA_70_1

1024x768

70,000

56,475

74,999

1328

1024

806

768

 

 

 

 

 

 

 

 

 

XGA_70_2

1024x768

70,000

57,052

78,047

1368

1024

815

768

 

 

 

 

 

 

 

 

 

XGA_72

1024x768

71,955

58,140

80,000

1376

1024

808

768

 

 

 

 

 

 

 

 

 

XGA_75_1

1024x768

75

60,024

78,752

1312

1024

800

768

 

 

 

 

 

 

 

 

 

XGA_75_2

1024x768

76

61,080

86,000

1408

1024

806

768

 

 

 

 

 

 

 

 

 

XGA_85

1024x768

85,000

68,680

94,500

1376

1024

808

768

 

 

 

 

 

 

 

 

 

180

 

R5976491 IQ PRO G500 01/02/2007

E. Standard Image Files

Name5

Resolution6

Fvert

FHor

Fpix

Ptot10

Pact11

Ltot12

Lact13

 

 

Hz7

kHz8

MHz9

 

 

 

 

XGA_EOS

1024x768

63,000

50,000

67,200

1344

1024

796

768

 

 

 

 

 

 

 

 

 

XGA75_GS

1024x768

74,534

59,701

79,284

1328

1024

801

768

 

 

 

 

 

 

 

 

 

SXGA_60

1280x1024

60

63,980

107.997

1688

1280

1066

1024

 

 

 

 

 

 

 

 

 

SXGA+_60_2

1400x1050

60

65,574

122,230

1864

1400

1089

1050

 

 

 

 

 

 

 

 

 

SXGA+_60_3

1400x1050

60

65,104

122,396

1880

1400

1085

1050

 

 

 

 

 

 

 

 

 

Table E-1

R5976491 IQ PRO G500 01/02/2007

 

181

E. Standard Image Files

182

 

R5976491 IQ PRO G500 01/02/2007

Glossary

GLOSSARY

AGC

Automatic Gain Control: allows an automatic amplitude (gain) control of the incoming video signal

ANSI 73.11

American power plug to connect the power cord to the wall outlet.

CEE7

European power plug to connect the power cord to the wall outlet.

Common address

Default address. Projector will always execute the command coming from a RCU programmed with that common address.

Component Video

In Component Video the term component describes a number (3) of elements that are needed to make up the video picture, these components areR-Y/Y/B-Y.A composite video signal on the other hand contains all the information needed for the color picture in a single channel of information

DVI

Digital Visual Interface is a display interface developed in response to the proliferation of digital flat panel displays.

The digital video connectivity standard that was developed by DDWG (Digital Display Work Group). This connection standard offers two different connectors: one with 24 pins that handles digital video signals only, and one with 29 pins that handles both digital and analog video. This standard uses TMDS (Transition Minimized Differential Signal) from Silicon Image and DDC (Display Data Channel) from VESA (Video Electronics Standards Association).

DVI can be single or dual link.

Graphics

Native resolution of the LCD panels = 1024 pixels x 768 pixels (4:3)

GUI

Graphic User Interface

IP

Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.

LAN

Local Area Network

PiP

PiP stands for "Picture in Picture" and allows to display multiple windows containing each of them an image. The windows may be of the video or data type.

Projector address

Address installed in the projector to be individually controlled.

Reality(SXGA)

Native resolution of the LCD panels = 1366 pixels x 1024 pixels (4:3)

Reality(SXGA+)

Native resolution of the LCD panels = 1400 x 1050 pixels (4:3)

SBC

Single Board Computer,

R5976491 IQ PRO G500 01/02/2007

 

183

Glossary

Video Selector

The Video Selector is a graphical interface which allows an overview of the different video inputs (Composite Video andS-Video)and whether they are active (signal connected) or not as well as the selection of these different signals.

WAN

Wide Area Network

184

 

R5976491 IQ PRO G500 01/02/2007

Index

INDEX

A

Address

37–38, 114

Program

38

RCU

38

Projector address 114

setting

37

Adjustments

113

lens

113

 

AGC

72

 

 

Auto Image

96

AutoImage

110

Setup

110

B

Background 86 Battery 17

Installation 17 blanking 67 Blanking 111

C

Cleaning

17, 175

 

 

dustfilters

175

 

 

Lens

17

 

 

 

 

configuration

 

132

 

 

server

132

 

 

 

Connections

 

19–20, 24–25

 

Communication

24

 

Communications

25

 

RS232 IN

25

 

 

input source connections

19

Input source connections

19–20

facilities

 

20

 

 

layers

19

 

 

power connection

19

 

Control

137

 

 

 

description

137

 

 

D

diagnostics

147

description

147

Diagnostics

82

Digital

23

 

DVI

23

 

Digital Zoom

39

Dimensions

6

projector

6

display

105

 

setup

105

dropzone 151, 153

dropping

153

tools

151

 

E

exchange

163–164, 167

example

 

167

 

installation

163

 

troubleschooting

164

Exchange

165

 

exchange integration

169

folder form

169

 

Extended configuration 25

F

FAQ

173

File

95, 97, 100–102

R5976491 IQ PRO G500 01/02/2007

copy

101

delete

102

edit

97

 

load

95

rename

100

Filters

175

cleaning

175

location

175

firmware

149

upgrade

149

Full screen representation 105

G

Gain 72–73

 

 

 

 

automatic control

72

 

manual control

73

 

Gemini

122

 

 

 

 

General

 

50–53

 

 

 

audio

51

 

 

 

 

Audio

 

51–52

 

 

 

settings

52

 

 

setup

51

 

 

 

identification

 

53

 

 

Standby Timer

50

 

General menu

49

 

 

freeze

 

49

 

 

 

 

pause

 

49

 

 

 

 

General settings

49

 

General Menu

49

 

Getting started

 

29, 33, 35, 37, 39–40

address

37

 

 

 

Controlling the projector

39

digital zoom

39

 

lamp runtime

33

 

 

quick set up

35

 

 

Quick Set up

35

 

 

lens

 

35

 

 

 

 

using the dialogboxes

40

using the menu

39

 

guidelines

161

 

 

 

general network config

161

Network 161

 

 

 

I

Identification screen

53

 

Image

62

 

 

 

 

 

resolution

62

 

 

 

 

image files

103

 

 

 

 

forced file load

103

 

Image files

177

 

 

 

 

standard

177

 

 

 

Image settings

55

 

 

Image menu

55

 

 

Input 21–24, 67

 

 

 

input balance

67

 

Input source connection

21–24

5-Cable input

 

21

 

Composite Video input

22

computer input

24

 

DVI

23

 

 

 

 

S-Video input

 

23

 

Input source connections

25–27

Extended configuration

25–27

5–cable

25

 

 

 

introduction

 

25

 

S-Video

26

 

 

 

summarizing

27

 

installation

163

 

 

 

 

procedure

163

 

 

 

Installation

9, 122

 

 

185

Index

Gemini

122

 

guidelines

9

 

Installation guidelines

9–10, 14

configurations 10

 

guidelines

9

 

lenses

14

 

 

Safety

9

 

 

safety warnings

9

L

lamp

34

 

 

 

error

34

 

 

 

Lamp

33

 

 

 

runtime

33

 

Lamp history

90

 

Lamp mode

 

87

 

Language

116

 

Layers

19

 

 

 

input

19

 

 

 

Lens

6, 16–17, 35, 113

Cleaning

 

17

 

lens adjustments

113

Packaging

6

 

unpack

 

6

 

quick Adjustment

35

removing

 

16

 

Lenses

14–15

 

available lenses

14

formulas

 

15

 

installation

15

 

Local keypad

29

 

M

Menu

39, 43, 55–58, 63–65, 67, 72–73, 75, 77–82, 85–87, 90–92,

95, 97, 100–102, 105–106, 109–110, 113–118, 121

Image files menu

95, 97, 100–102

copy file

101

 

 

 

delete file

 

102

 

 

 

edit file

97

 

 

 

load file

95

 

 

 

rename file

100

 

 

Image menu

 

55–58, 63–65, 67, 72–73

AGC on video

72

 

aspect ratio

58

 

 

Brightness

56

 

 

 

color

56

 

 

 

 

 

color temperature

 

64

contrast

56

 

 

 

filmmode detection

65

Gamma

57

 

 

 

input balance

67

 

 

Keystone

 

63

 

 

 

manual gain control

73

noise reduction

58

phase

58

 

 

 

 

settings

55

 

 

 

sharpness

57

 

 

 

Tint 57

 

 

 

 

 

installation menu

113

Installation menu

105–106, 109–110, 113–118, 121

AutoImage Setup

110

Automatic startup

 

118

change password

 

121

Full screen representation 105

language

116

 

 

 

lens adjustments

113

projector address

114

projector orientation

115

Quick access keys

 

117

RS232 baudrate

118

Sliderbox position

 

109

Startup screen

105

Take screenshot

106

186

 

 

 

 

 

 

 

textbox

106

 

 

Lamp menu

87, 90–92

history

90

 

 

 

Mode

87

 

 

 

reset runtime

91

 

Runtime warning

92

runtimes

87

 

 

Signal menu

85–86

background

86

 

switching mode

85

Source selection

43

structure

39

 

 

 

Tools 75

 

 

 

 

PiP

75

 

 

 

 

Tools menu 75, 77–82

Diagnostics

82

 

PiP add window

77

PiP Adjust

81

 

 

PiP delete layout

80

PiP layout

79

 

 

PiP remove window 78

PiP rename layout

80

PiP Save

79

 

 

PiP select

77

 

 

using the menu

39

 

menu bar

108

 

 

 

N

Native resolution 62

 

network

127, 129, 138–139, 144, 151, 155, 158–159, 161

additional config info

161

configuration

129

 

control

138–139, 144

advanced

144

 

general

138

 

 

interface

 

138

 

 

source selection

139

dropzone

151, 155

 

remote desktop sharing 155

Dropzone

155

 

 

file manager

155

 

DropZone

151, 158

settings

158

 

 

start up

151

 

 

Server

127

 

 

 

start up

127

 

 

web 159

 

 

 

 

Network

123–127, 137, 139, 142, 145, 147–148

architecture

123

 

configuration

148

 

E-mail

148

 

 

Connections

126

 

control

145

 

 

 

advanced lens adjustments 145

advanced options

145

Control manager

139, 142

image settings

142

PiP

139

 

 

 

diagnostics manager

147

functionality

124

 

Getting started

125

 

installing

127

 

 

software

 

127

 

 

Projector

137

 

 

control

137

 

 

No signal

86

 

 

 

background

86

 

 

O

Orientation 115

projector orientation 115 oulook integration 170

limitations 170

R5976491 IQ PRO G500 01/02/2007

Index

outlook intagration 167

P

Packaging

5–6

 

Lens 6

 

 

 

projector

5

 

parameter

165

 

list

165

 

 

 

Password

121

 

change password

121

PiP

77–81

 

 

 

add window

77

 

adjust

81

 

 

 

layout

79

 

 

 

Layout

79–80

 

delete

80

 

rename

 

80

 

save

79

 

 

remove window

78

select

77

 

 

 

Power mode

 

89

 

Projector

5–6, 32, 38

Controlling

 

38

 

dimensions

5–6

 

packaging

 

5

 

Packaging

 

5

 

unpack

 

5

 

Switch on

 

32

 

Q

Quick access keys 117

R

RCU

17, 29, 31, 35

Battery

17

 

Terminology

31

Overview

31

Using

35

 

Removing

16

 

lens

16

 

RS232 baudrate

118

Runtime

91–92

reset 91 warning 92

S

Screenshot 106 security 119 shipped Box 5

content 5 Sliderbox position 109 SNMP 171

installation 171 integration 171

Source 43, 85 selection 43 Source selection 43 switching mode 85

source files 177 standard 177

Source selection 44–46 composite video 44 S-Video 45

video selector 46 specifications 125 Startup 118

automatic 118 Startup screen 105 status bar 108 Switching 85

switching mode 85

T

Textbox 106 Timer 50

troubleshooting 173

V

Video

22–23, 72–73

AGC

72

Composite Video 22 manual gain control 73 S-Video 23

R5976491 IQ PRO G500 01/02/2007

 

187

 

Index

188

 

R5976491 IQ PRO G500 01/02/2007

Revision Sheet

To:

Barco nv Presentations

Noordlaan 5, 8520 Kuurne

Phone: +32 56.36.82.11, Fax: +32 56.35.86.51

E-mail:presentations.bid@barco.com, Web: www.barco.com

From:

Date:

Please correct the following points in this documentation (R5976491/09):

page

wrong

correct

 

 

 

R5976491 IQ PRO G500 01/02/2007