Barco GRAPHICS 500 R9002930 User Manual
Size:
6.88 Mb
Download

13. Installation menu

13.5 Quick access keys

What can be done ?

The 3 function keys on top of the RCU can be associated with a particular item in one of the menus.

Each function which is not password protected or does not have a key on the RCU can be associated to a function key.

How to get an overview of the quick access keys ?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Quick access keys (image 13-9)

5.Press ENTER

A text box appears on the screen.

Image 13-9

How to program the quick access keys ?

1.Scroll through the menus to the desired menu item

2.Push the desired function key for 3 seconds (image 13-10)The menu item is stored in the quick access key

 

F 1

F 2

 

 

F 3

 

 

 

 

 

M EN U

 

B A C K

Image 13-10

Factory pre-programmedfunctions

-F1 :color depth

-F2 :noise reduction-F3 :orientation

R5976367 BARCOIQ GRAPHICS 500 01/02/2007

 

119

13. Installation menu

13.6 RS232 baudrate

How to change the baudrate?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation item

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select RS232 baudrate (image 13-11)

5.Press → to pull down the menu

6.Use ↓ or ↑ to select the desired baudrate

7.Press ENTER

Image 13-11

13.7 Automatic startup

What can be done ?

The automatic startup allows immediate restart of the projector after a power failure (breakdown), i.e. without passing through the standby state.

The projector restarts at power resume and recovers the previous settings (previous source,...).

This function can be disabled if undesired or inadequate for safety reasons, etc.

CAUTION: If the Automatic startup function is enabled one must be aware of the fact that it involves safety precautions

Make sure that the projector (or the operators!) will not be affected by altered environmental conditions when restarting at power resume.

How to enable/disable the Automatic startup?

1.Press MENU to activate the Tool bar

2.Press → to select the Installation item

3.Press ↓ to Pull down the Installation menu

4.Use ↑ or ↓ to select Automatic startup

5.Press → to pull down the menu

6.Use ↓ or ↑ to enable/disable the automatic startup

7.Press ENTER

120

 

R5976367 BARCOIQ GRAPHICS 500 01/02/2007

 

13. Installation menu

13.8 Security

What can be done ?

A security function is implemented in the projector and allows a protection against theft.

A PIN code allows the user to lock the projector in case of wrong code entry.

The PIN code must be entered at each start up (Power ON), entering three times a wrong number triggers a wait cycle of 15 minutes,

the second 3 wrong codes a wait cycle of 30 minutes, 1 hour, ...

The security mode can be enabled or disabled.

How to activate the security mode ?

1.Press MENU to activate the Tool bar

2.Press → to select the installation item

3.Press ↓ to Pull down the menu

4.Use ↑ or ↓ to select Security (image 13-12)

5.Press → to open the menu

6.Use ↑ or ↓ to select ON

7.Press ENTER

A dialog box is displayed (image 13-13)

8.Use the arrow keys to select YES and press ENTER to confirm A dialog box is displayed

Enter your name, company name,... (this information is displayed in the identification menu) (image 13-14)

9.Press ACCEPT

A dialog box is displayed.

Enter the PIN code, and confirm it. (image 13-15)

An informative text box is then displayed. Press ENTER orBACK to escape.(image 13-16)

Image 13-12

R5976367 BARCOIQ GRAPHICS 500 01/02/2007

 

121

13. Installation menu

Image 13-13

Image 13-15

Image 13-14

Image 13-16

How to disable the security mode ?

1.Press MENU to activate the Tool bar

2.Press → to select the installation item

3.Press ↓ to Pull down the menu

4.Use ↑ or ↓ to select Security

5.Press → to open the menu

6.Use ↑ or ↓ to select OFF

7.Press ENTER

122

 

R5976367 BARCOIQ GRAPHICS 500 01/02/2007