Barco GRAPHICS 500 R9002930 User Manual
Size:
6.88 Mb
Download

12. Display setup

12. DISPLAY SETUP

Overview

Full screen representation

Startup screen

Textbox

Take screenshot

Menu bar position

Status bar position

Sliderbox position

AutoImage Setup

Blanking

12.1Full screen representation

Purpose of the Full screen representation

The Full screen representation function forces to use the complete native resolution of the LCD panels independently of the native resolution of the source.

Note that the full screen representation does not preserve the aspect ratio of the source, i.e. when the aspect ratio of the active image is not the same as the projector (in this case 1920/1080 or 1.77:1), the image will end to be distorted (stretched or shrinked).

How to enable/disable the full screen representation ?

1.Press MENU to activate the Tool bar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Full screen representation

5.Press → to pull down the menu

6.Use ↓ or ↑ to select ON or OFF

7.Press ENTER

The full screen representation will not guarantee the best image quality, therefore the Show native resolution has to be selected.

The show native resolution function on the other hand forces to use the native resolution of the source. TheFull screen representation function overrules theshow native resolution function.

The aspect ratio setting is greyed out when enabling the full screen representation.

12.2 Startup screen

What can be done ?

When the startup screen is enabled, the identification screen is displayed for a few seconds at startup. This startup screen can also be disabled.

R5976367 BARCOIQ GRAPHICS 500 01/02/2007

 

107

12. Display setup

Image 12-1

How to enable/disable the Startup screen?

1.Press MENU to activate the Tool bar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Startup screen

5.Press → to pull down the menu

6.Use ↓ or ↑ to select the ON or OFF

7.Press ENTER

12.3Textbox

What can be done ?

The textbox function allows to display or not the different sliderboxes used for instance for picture settings (contrast,...), it also affects the source information windows (displayed in the right lower corner of the screen).

How to enable/disable the Textbox ?

1.Press MENU to activate the Toolbar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Textbox

5.Press → to pull down the menu

6.Use ↓ or ↑ to enable/disable the textbox

7.Press ENTER

12.4Take screenshot

What can be done ?

A screenshot can be taken from an active projected image. This screenshot is then saved in a 4 MB RAM and can be used as background.

Each new screenshot erases the previous logo therefore a warning message is displayed asking the user to confirm.

108

 

R5976367 BARCOIQ GRAPHICS 500 01/02/2007

12. Display setup

Image 12-2

Default (factory stored) Logo

How to take a screenshot ?

1.Press MENU to activate the Tool bar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Take screenshot (image 12-3)

5.Press ENTER

A dialog box is displayed. Press yes to confirm.(image 12-4)

A text box shows the evolution of the operation. (image 12-5,image 12-6)

Image 12-3

Image 12-4

Image 12-5

Image 12-6

R5976367 BARCOIQ GRAPHICS 500 01/02/2007

 

109

12. Display setup

12.5 Menu bar position

What can be done ?

The menu toolbar can be centered vertically , the range being from top of the screen to the middle of the screen. This can be useful in applications where the top image content is not displayed.

How to center the menu ?

1.Press MENU to activate the Toolbar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Menu bar position menu (image 12-7)

5.Press ENTER

6.Use ↑ or ↓ to position the menu toolbar

Image 12-7

12.6 Status bar position

What can be done ?

The status bar (wizard menu) can be centered vertically , the range being from bottom of the screen to the middle of the screen. This can be useful in applications where the bottom image content is not displayed.

How to center the menu ?

1.Press MENU to activate the Toolbar

2.Press → to select the Display setup item

3.Press ↓ to Pull down the Display setup menu

4.Use ↑ or ↓ to select Status bar position (image 12-8)

5.Press ENTER

6.Use ↑ or ↓ to position the status bar

110

 

R5976367 BARCOIQ GRAPHICS 500 01/02/2007