4. Getting started

Some projectors may operate in domestic environments where other equipments may listen to the common address “0” , therefore the common address can also be set to “1”.

4.7.2Displaying and Programming addresses into the RCU

Displaying the Projector Address on the Screen.

1.Press the Address key (recessed key on the RCU) with a pencil. The projector’s address will be displayed in a ’Text box’

To continue using the RCU with that specific address, it is necessary to enter the same address with the digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the Address key displays projector address 003, then press "3" digit button on the RCU to set the RCU’s address to match the projector’s address. Do not press 0–0–3 .This will address the remote control to ’0’ and control all projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default address (zero address) and controls then all projectors in the room.

Address 0 (or 1) should always allow communication with the projector since it is a common address.

Displaying the Projector Address in Standby.

1.Press the Address key (recessed key on the RCU) with a pencil. All the LED’s on the front of the projector go out.

Then LED1 starts blinking green the number of hundreds. After that LED2 starts blinking the number of tens. Finally LED3 starts blinking green the number of units. If this is done, the original status of the leds is restored.

4.8Controlling the projector

Input Selection

Key in the corresponding slot number with the digit keys on the RCU. The selected source will be displayed.

Picture Controls

When an image control is pressed, a text box with a bar scale, icon and function name of the control, e.g. ’brightness...’ appears on the screen (only if Textbox in the Installation menu is ON). The length of the bar scale and the value of the numeric indication indicate the current memorized setting for this source. The bar scale changes as the arrows on the RCU are pressed or the + or - buttons on the local keypad.

The picture settings are saved in the image file.

Image 4-14

Brightness	Use the + button for a higher brightness.
	Use the - button for a lower brightness.
Contrast	Use the + button for a higher contrast.
	Use the - button for lower contrast.
Color	Use the + button for richer colors.
	Use the - button for lighter colors.
Tint(Hue)	Tint is only active for Video and S-Videowhen using the NTSC 4.43 or NTSC 3.58 system.
	Use the + button
	Use the - button.

40

R5976367 BARCOIQ GRAPHICS 500 01/02/2007

4. Getting started

Sharpness	Use the + button for a sharper picture.
	Use the - button for a softer picture.
Phase	Use the + or - button to adjust the phase.
Gamma	Use the + button for a higher gamma
	Use the - button for a lower gamma
Freeze	Press Freeze to freeze the displayed image.

The Pause Key

When the Pause key is pressed, the image projection is stopped, a black screen will be displayed

To restart the image projection:

•Press PAUSE key

•Press BACK key

•Select a source number

4.9Digital Zoom

What can be done ?

The Digital Zoom key on the RCU allows to zoom (in or out) one particular part of the image

How to Zoom ?

1.Press ← or → on the Digital Zoom key on the remote to Zoom the center of the image A wizardbox is displayed in the lower part of the screen, follow the instructions.

Use the BACK key to undo the Zoom function.

Digital Zoom can not be performed on a logo.

4.10 Menu structure

PC like menustructure

The projector has a build in "PC like" toolbar menu which allows easy access to different parameters for setting up the projector. The menu is activated by pressing MENU, it contains 2 levels depending on the type of user:

•Level 1: standard user

•Level 2: advanced user, level 2 is password protected, the advanced parameters are only visible when the correct password has been entered ( factory password = "0000")

Menu items which are not applicable are greyed out.

4.11 Using the menu

Menu Layout

A grey line gives the transition between standard and advanced parameters.

The existence of a submenu is indicated by a white arrow, Settings is a submenu.

Keystone is an item of theImage menu.

R5976367 BARCOIQ GRAPHICS 500 01/02/2007		41

4. Getting started

Three suspension points indicate that the menuitem hides a dialogbox or a textbox.

Image 4-15

The menus inserted in this manual are of the advanced type: all the items are visible The menus seen by a standard user on the screen will hence not correspond with the menus in the manual i.e. the advanced items will not be visible, they will be replaced with "More..."

Greyed out menus or items are not available in this software version

How to pull down a menu ?

1. Use ↓ to pull down a menu

How to pull down a submenu ?

1. Use → to pull down a submenu

How to exit the submenu ?

1. Press BACK to exit a submenu

Press MENU to exit the menu

When the menu has been exited for more than 1 minute, the advanced user password has to be re-entered.

4.12 Using the Dialogboxes

How to use the dialogboxes ?

Some parameters are modified by means of a dialogbox, where selections can be made and/or values can be entered, The values can be entered in several ways:

Entering numeric values using the numeric keys on the remote control

1.Press ENTER to activate the input field(image 4-16)

2.Key in the desired value

42

R5976367 BARCOIQ GRAPHICS 500 01/02/2007

4. Getting started

Image 4-16

Entering numeric values using the arrow keys on the remote control

1.Press ENTER to activate the input field.

2.Press ←or → to select the digit to be changed (image 4-17)

3.Press ↓ or ↑ to increase or decrease the value

Image 4-17

Entering numeric values using the arrow keys on the local keypad

1.Press ENTER to activate the input field.

2.Press ←or → to select the digit to be changed

3.Press ↓ or ↑ to increase or decrease the value

To confirm the changes always press ENTER.

Use ↓ or ↑ to browse between the different fields.

In some cases an alphanumeric value (file name, ...) has to be entered. Use ↑ or ↓ to scroll through the character values once the input field is activated

Following characters can be browsed in this particular order:

Decimal scroll list: 0123456789

Signed decimal scroll list: 0123456789-

ASCII scrolllist:ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789+-*/&@#.;.abcdefghijklmnopqrstuvwxyz

R5976367 BARCOIQ GRAPHICS 500 01/02/2007

43

4. Getting started

44

R5976367 BARCOIQ GRAPHICS 500 01/02/2007