Barco GRAPHICS 1208S R9000893 User Manual
Size:
2.2 Mb
Download

GRAPHICS 1208s

R9000893

R9000896

OWNER'S MANUAL

BARCO PROJECTION SYSTEMS

GRAPHICS 1208s

R9000893

R9000896

OWNER'S MANUAL

Date :

Art. No. :

220197

R5975847

Due to constant research, the information in this manual is subject to change without notice.

Produced by BARCO NV, January 1997.

All rights reserved.

Trademarks are the rights of their respective owners.

Printed in Belgium

BARCO nv/Projection Systems

Noordlaan 5

B-8520Kuurne

Belgium

Printed in Belgium

 

 

Table of Contents

 

 

 

 

Table of contents ...........................................................................................................................................................................

 

i

Safety instructions .....................................................................................................................................................................

1-1

On safety .............................................................................................................................................................................

1-1

On installation .....................................................................................................................................................................

1-2

On servicing ........................................................................................................................................................................

1-2

On cleaning .........................................................................................................................................................................

1-2

On repacking .......................................................................................................................................................................

1-2

On illumination .....................................................................................................................................................................

1-2

Location and Functions of Control ...........................................................................................................................................

2-1

Rear panel terminology ........................................................................................................................................................

2-1

Front panel terminology .......................................................................................................................................................

2-1

Control panel terminology ....................................................................................................................................................

2-2

a. The Local Keypad ............................................................................................................................................................

2-2

b. RCU control panel terminology ........................................................................................................................................

2-2

Connections ...............................................................................................................................................................................

3-1

AC Power (mains) Cord Connection ....................................................................................................................................

3-1

Power Check .......................................................................................................................................................................

3-1

Switching On/Off .................................................................................................................................................................

3-1

Signal Input Connection to the Projector : ............................................................................................................................

3-2

Connecting a Composite Video source to port 1. .................................................................................................................

3-3

Connecting a S-Videoor Video source to port 2. .................................................................................................................

3-3

Connecting a RGB Analog source to port 3. ........................................................................................................................

3-4

Connecting a RGB Analog source to port 4/5. ......................................................................................................................

3-4

Connecting a RGB Analog source with Tri-levelsync to port 4/5.(option) .............................................................................

3-5

Connecting a Component Video source to port 4/5. .............................................................................................................

3-5

Connecting a Component Video source with Tri-levelsync to port 4/5.(Opion) .....................................................................

3-5

Peripheral equipment ...........................................................................................................................................................

3-6

Connecting a RCVDS 05 switcher to the BARCOGRAPHICS 808s .....................................................................................

3-6

Connecting a VS05 switcher to the BARCOGRAPHICS 808s. .............................................................................................

3-6

Connecting an IR Remote Receiver to the BARCOGRAPHICS 808s ...................................................................................

3-6

Controlling ..................................................................................................................................................................................

4-1

Battery installation in the RCU. ............................................................................................................................................

4-1

How to use your RCU ..........................................................................................................................................................

4-2

Projector Address ................................................................................................................................................................

4-2

How to display a projector address? ....................................................................................................................................

4-3

How to program an address into the RCU? ..........................................................................................................................

4-3

Input selection .....................................................................................................................................................................

4-3

Analog Picture Controls .......................................................................................................................................................

4-4

Controlling chained projectors. ............................................................................................................................................

4-4

Start up of the Adjustment Mode ..............................................................................................................................................

5-1

Adjustment Mode ................................................................................................................................................................

5-1

Random Access Adjustment Mode ...........................................................................................................................................

6-1

Starting-Upthe Random Access Adjustment mode. .............................................................................................................

6-1

Overview 'Random Access Adjustment' mode .................................................................................................................

6-1

Selecting Setup Pattern .......................................................................................................................................................

6-3

Internal Cross Hatch Pattern ................................................................................................................................................

6-3

Random access adjustment mode selection menu. .............................................................................................................

6-4

Picture Tuning .....................................................................................................................................................................

6-4

Color Balance ......................................................................................................................................................................

6-4

Sync Fast/Slow Adjustment .................................................................................................................................................

6-5

Peaking ...............................................................................................................................................................................

6-5

Clamp Tuning ......................................................................................................................................................................

6-5

Port 2 : Video or S-Video .....................................................................................................................................................

6-6

Line Doubler ........................................................................................................................................................................

6-6

Color Select .........................................................................................................................................................................

6-6

Focusing .............................................................................................................................................................................

6-7

Focusing color select. ..........................................................................................................................................................

6-7

Blue on source ....................................................................................................................................................................

6-7

Geometry Adjustments ........................................................................................................................................................

6-8

Horizontal Phase Adjustment ...............................................................................................................................................

6-8

Raster Shift Adjustment .......................................................................................................................................................

6-9

Left-Right(east-west)Adjustments ....................................................................................................................................

6-10

Seagull correction ..............................................................................................................................................................

6-11

Left Side Correction ...........................................................................................................................................................

6-11

Top-Bottom(north-south)Adjustments ..............................................................................................................................

6-12

Seagull Correction .............................................................................................................................................................

6-13

Horizontal Size Adjustment ................................................................................................................................................

6-13

Vertical Linearity Adjustment .............................................................................................................................................

6-14

Vertical Size Adjustment ....................................................................................................................................................

6-14

5975847 BARCOGRAPHICS 1208S 220197

 

 

i-1

 

 

Table of Contents

Blanking Adjustments ........................................................................................................................................................

6-15

Convergence Adjustment ..................................................................................................................................................

6-16

Service mode .............................................................................................................................................................................

7-1

Starting up the Service mode. .............................................................................................................................................

7-1

Overview flowchart 'Service' mode. .................................................................................................................................

7-1

Identification ........................................................................................................................................................................

7-2

Copy a block .......................................................................................................................................................................

7-2

Deletion of blocks ................................................................................................................................................................

7-3

Deleting block by block .......................................................................................................................................................

7-3

Deletion of all blocks ...........................................................................................................................................................

7-3

Change password ...............................................................................................................................................................

7-4

Change Language ...............................................................................................................................................................

7-4

Run time .............................................................................................................................................................................

7-4

Set to midposition ...............................................................................................................................................................

7-5

Undo Midposition ................................................................................................................................................................

7-5

Convergence Mid ................................................................................................................................................................

7-5

Undo Convergence Mid(position) ........................................................................................................................................

7-5

Dynamic Astigmatism (spot shape adjustment) ...................................................................................................................

7-6

G2 Adjust ............................................................................................................................................................................

7-7

Gamma corrections .............................................................................................................................................................

7-7

CRT run in cycle .................................................................................................................................................................

7-7

Projector Warm Up ..............................................................................................................................................................

7-8

CRT Drive Mode .................................................................................................................................................................

7-8

Messages, warnings and failures .............................................................................................................................................

8-1

Options .......................................................................................................................................................................................

9-1

Appendix A : Orbiting ...................................................................................................................................................................

A-1

Appendix B : Adjsutment Blocks and Source Numbers 90-99 ......................................................................................................

B-1

i-2

 

5975847 BARCOGRAPHICS 1208S 220197

 

Safety Instructions

1

SAFETY INSTRUCTIONS

 

Notice on Safety

This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 No.950, which are the safety standards of information technology equipment including electrical business equipment.

WARNING

TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE

These safety standards impose important requirements on the use of safety critical components, materials and isolation, in order to protect the user or operator against risk of electric shock and energy hazard, and having access to live parts.

Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire.

Simulated single fault condition testing ensures the safety of the equipment to the user even when the equipment's normal operation fails.

INSTALLATION INSTRUCTIONS

Before operating this equipment please read this manual thoroughly, and retain it for future reference.

Installation and preliminary adjustments should be performed by qualified BARCO personnel or by authorized BARCO service dealers.

OWNER’S RECORD

The part number and serial number are located at the back side of the projector. Record these numbers in the spaces provided below. Refer to them whenever you call upon your BARCO dealer regarding this product.

PART NUMBER :

SER. NUMBER :

DEALER :

The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons.

The exclamation point within a triangle is intended to tell the user that important operating and/or servicing instructions are included in the technical documentation for this equipment.

FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)

This equipment has been tested and found to comply with the limits of a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Note :

The use of shielded cables is required to comply within the limits of Part 15 of FCC rules and EN55022.

*All the safety and operating instructions should be read before using this unit.

*The safety and operating instructions manual should be retained for future reference.

*All warnings on the equipment and in the documentation manuals should be adhered to.

*All instructions for operating and use of this equipment must be followed precisely.

On safety

1. This product should be operated from an AC power source. This projector may be connected to anIT-powersystem.

Operating AC power voltage of the projector:

BARCOGRAPHICS 1208s

Art. No. R9000893 è 230V AC

Art. No. R9000896 è 120V AC

Consult your dealer to switch over from 230Vac to 120 Vac or from 120Vac to 230 Vac.

If you are not sure of the type of AC power available, consult your dealer or local power company.

2. This product is equipped with a3-wiregrounding plug, a plug having a third (grounding) pin. This plug will only fit into a groundingtype power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of thegrounding-typeplug.

WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE GROUNDED (EARTHED) via the supplied 3 conductor AC power cable.

(If the supplied power cable is not the correct one, consult your dealer.)

5975847 BARCOGRAPHICS 1208S 220197

 

1-1

 

Safety Instructions

A. Mains lead (Power cord) with CEE 7 plug:

The wires of the mains lead are colored in accordance with the following code.

Green and yellow:

earth (safety earth)

Blue:

neutral

Brown:

line (live)

B. Power cord with ANSI 73.11 plug:

The wires of the power cord are colored in accordance with the following code.

Green/yellow: ground

White:

neutral

Black:

line (live)

3. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.

To disconnect the cord, pull it out by the plug. Never pull the cord itself.

4. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. Also make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.

5. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock.

Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before resuming operations.

6. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the projector due to lightning and ACpower-linesurges.

On installation

1. Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it.

2. Do not use this equipment near water.

3. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register.

The projector should not be placed in a built-ininstallation or enclosure unless proper ventilation is provided.

4. Do not block the projector cooling fans or free air movement under and around the projector. Loose papers or other objects may not be nearer to the projector than 4" on any side.

On servicing

Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock!

Refer all servicing to qualified service personnel.

Unplug this product from the wall outlet and refer servicing to

qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the equipment.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally when the operating instructions are followed.

Note : Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

e.If the product has been dropped or the cabinet has been damaged.

f.If the product exhibits a distinct change in performance, indicating

aneed for service.

Replacement parts - When replacement parts are required, be sure the service technician has used original BARCO replacement parts or authorized replacement parts which have the same characteristics as the BARCO original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.

Safety check - Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks to determine that the product is in proper

operating condition.

On cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

- To keep the cabinet lookingbrand-new,periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet.

-To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflectivecoating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.

On repacking

Save the original shipping carton and packing material; they will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory.

On illumination

In order to obtain the best quality for the projected image, it is essential that the ambient light which is allowed to fall on the screen be kept to an absolute minimum.

When installing the projector and screen, care must be taken to avoid exposure to ambient light directly on the screen. Avoid adverse illumination on the screen from direct sunlight or fluorescent lighting fixtures.

The use of controlled ambient lighting, such as incandescent spot light or a dimmer, is recommended for proper room illumination. Where possible, care should also be taken to ensure that the floors and walls of the room in which the projector is to be installed are nonreflecting, dark surfaces. Brighter surfaces will tend to reflect and diffuse the ambient light and hence reduce the contrast of the projected image on the screen.

1-2

 

5975847 BARCOGRAPHICS 1208S 220197