Barco 26-0503000-00 User Manual
Size:
991.7 Kb
Download

4. Operation

Using the Main Menu

~If All is selected and all equalization values do not match, the label “Not All Same” is shown.

~If an individual input is selected, its equalization value is shown.

6.Rotate the ADJUST knob and select the desired equalization value.

Note

If you selected All, but all equalization values currently do not

 

match, you will overwrite all “differing” values with a new

 

“global” equalization value.

 

 

7.Press SEL to “accept” the new resolution, or pressESC to return to the current value without making changes. If you accept the new value, visually check the quality of the signal on the monitor.

8.As required, repeat step 5 to obtain the optimum quality signal.

9.(Optional) If required:

~Scroll to the “Set to Default” line and pressSEL to reset the equalization value for all inputs to the default value to4.

~Scroll to the “Set to Maximum” line and pressSEL to set the value to15.

~Scroll to the “Set to Minimum” line and pressSEL to set the value to0.

qЙлн=m~ннЙке=jЙем

From the Main Menu, select Test Patternto display the Test Pattern Menu.

TEST PATTERN

>1400x1050 @59.94

Output

All

 

Type

H Ramp

 

 

 

 

Figure 4-14. MatrixPRO Test Pattern Menu (sample)

The Test Pattern Menu enables you to perform the following functions:

Pre-selectwhich test pattern will be displayed when theTEST PAT button is routed to an output. One pattern can be set for all outputs, or individual test patterns can be set on anoutput-by-outputbasis. The menu itself does not enable the route.

Set the “global” output resolution of the test pattern.

Enable the Raster Box for a “test pattern” route already in effect.

Menu instructions are provided in the following sections:

Using the Test Pattern

Using the Raster Box

MatrixPRO • 8x8 DVI Router • User’s Guide

 

43

 

4. Operation

Using the Main Menu

rлбеЦ=нЬЙ=qЙлн=m~ннЙке

Use the following steps to pre-selecta test pattern:

1.From the Main Menu, select Test Patternto display the Test Pattern Menu.

2.Scroll to line 2 (the “Resolution” line), and pressSEL to display the edit cursor (#).

3.Rotate the ADJUST knob and select the desired “global” test pattern resolution for all outputs.

4.Press SEL to “accept” the new resolution, or pressESC to return to the current resolution without making changes.

5.Scroll to line 3 (the “Output” line), and pressSEL to select either all outputs, or an individual output for which you want to set a test pattern.

6.Scroll to line 4 (the “Type” line), which displays the current test pattern for the output selected on line3. PressSEL to display the edit cursor (#). Please note:

~If All is selected and test patterns match, the “global” test pattern is shown on the line.

~If All is selected and all test patterns do not match, the label “Not All Same” is shown.

~If an individual output is selected, its test pattern is shown.

7.Rotate the ADJUST knob and select the desired test pattern. Choices are:

~H Ramp, V Ramp

~75% Col Bars, 100% Col Bars

~16x16 Grid, 32x32 Grid

~Burst, 50% Gray

~Gray Steps 1, Gray Steps 2

~White, Black, Red, Green, Blue

Note

If you selected All, but all test patterns currently do not match,

 

you will overwrite all “differing” patterns with a new “global”

 

test pattern.

 

 

8.Press SEL to “accept” the new pattern, or pressESC to return to the current pattern without making changes. The pattern inpre-selected at this point.

9.To route the selected pattern to an output:

a.In the Output Selection Section, select the desired output.

b.Press TEST PAT.

c.Press TAKE.

The selected pattern is routed to the selected output only. All other routes are unaffected.

10.To clear the test pattern from the output:

a.In the Output Selection Section, select the desired output.

b.Press TEST PAT or select an input.

c.Press TAKE.

44

 

MatrixPRO • 8x8 DVI Router • User’s Guide