Barco 26-0503000-00 User Manual
Size:
991.7 Kb
Download

4. Operation

Using the Main Menu

pÉíìé=jÉåì

From the Main Menu, selectSetup to display theSetup Menu:

 

 

 

 

 

SETUP

 

 

 

> System

>>

 

 

Factory Reset

>>

 

 

Tech Support

>>

 

 

 

 

 

Figure 4-4. MatrixPRO Setup Menu

The Setup Menu enables you to adjust system parameters, perform a factory reset or obtain the Tech Support number. Following are descriptions of each menu function:

System Menu

Factory Reset Menu

Tech Support Menu

pулнЙг=jЙем

From the Setup Menu, selectSystem to display theSystem Menu.

 

 

 

 

 

SYSTEM

 

 

 

> VFD Brightness

+8

 

 

RS-232Settings

>>

 

 

DHCP

OFF

 

 

IP Address

>>

 

 

Subnet Mask

>>

 

 

 

 

 

Figure 4-5. MatrixPRO System Menu

Each menu is explained in detail below:

VFD Brightness

RS-232 Settings Menu

DHCP

IP Address

Subnet

sca=_кбЦЬнеЙлл

On the System Menu, theVFD Brightness function allows you to adjust the vacuum fluorescent display (VFD) brightness.

To change VFD brightness:

1.On the System Menu, scroll to theVFD Brightness line and pressSEL.

2.Rotate the knob to select the desired brightness. Values range from 0 to15.

3.Press SEL to accept the new setting.

36

 

MatrixPRO • 8x8 DVI Router • User’s Guide

 

4. Operation

Using the Main Menu

opJOPO=pЙннбеЦл=jЙем

From the System Menu, selectRS-232 Settings to display theRS-232 Settings Menu. This menu enables you to adjust the settings of the rear panel’sSerial Port.

 

 

 

 

 

RS-232SETTINGS

 

 

 

> Baud Rate

115200

 

 

Parameters

[N81]

 

 

 

 

 

 

 

 

 

Figure 4-6. MatrixPRORS-232Settings Menu

Please note:

Baud rate choices are: 2400, 4800, 9600, 19200, 38400, 57600, and 115200.

Parameters are fixed at N81 (one start bit, eight data bits, one stop bit and no parity bit), and cannot be adjusted.

To change the RS-232port’s baud rate:

1.On the RS-232Settings Menu, press SEL.

2.Rotate the knob to select the desired baud rate.

3.Press SEL to accept the new value.

ae`m

On the System Menu, theDHCP function allows you to enable or disable DHCP.

When enabled, the router’s IP address and subnet mask are set by your network’s DHCP server, and cannot be changed locally. Use this setting when connected to an external controller, such as Encore.

When disabled, the system’s static IP address and subnet mask are active, and can be changed locally.

To change the DHCP setting:

1.On the System Menu, scroll to theDHCP line and pressSEL.

2.Rotate the knob to select the desired setting (on or off).

3.Press SEL to accept the new setting.

fm=^ЗЗкЙлл

From the System Menu, selectIP Address to display theIP Address Menu.

IP ADDRESS

192.168.000.243

^

Figure 4-7. MatrixPRO IP Address Menu

When this menu item is selected (and DHCP is off), the cursor (^) is positioned under theright-mostdigit in the address.

MatrixPRO • 8x8 DVI Router • User’s Guide

 

37

 

4. Operation

Using the Main Menu

Please note:

The default IP address is 192.168.000.243.

If DHCP is on, the IP address appears between brackets, and cannot be adjusted.

To adjust the IP address:

1.Ensure that DHCP is off.

2.On the IP Address Menu, rotate the knob to change the value of the digit to which the cursor is pointing.

3.Press SEL to update the number and advance the cursor one place to the left.

4.Repeat steps 1 and2 as required. Note that repeatedly pressingSEL advances through the digits, skipping thedecimal-pointfield delimiter.

5.To accept the new IP address, press ESC at any time to exit the menu. The new IP address will take effect at this point.

pмДеЙн

From the System Menu, selectSubnet Mask to display theSubnet Menu.

SUBNET

255.255.255.000

^

Figure 4-8. MatrixPRO Subnet Menu

When this menu item is selected (and DHCP is off), the cursor (^) is positioned under theright-mostdigit in the address.

Please note:

The default Subnet Mask is 255.255.255.000.

If DHCP is on, the Subnet Mask appears between brackets, and cannot be adjusted.

To adjust the Subnet Mask:

1.Ensure that DHCP is off.

2.On the Subnet Menu, rotate the knob to change the value of the digit to which the cursor is pointing.

3.Press SEL to update the number and advance the cursor one place to the left.

4.Repeat steps 1 and2 as required. Note that repeatedly pressingSEL advances through the digits, skipping thedecimal-pointfield delimiter.

5.To accept the new Subnet Mask, press ESC at any time to exit the menu. The new Subnet Mask will take effect at this point.

38

 

MatrixPRO • 8x8 DVI Router • User’s Guide