Bakers Pride Oven CS70-CHUS15 User Manual

Size:
1.74 Mb
Download

Figure 16

Figure 17

Figure 18

Figure 19

6.1f. Replacing the thermometer.

Required: Crescent or standard 3/4" wrench

1.Remove front panel as found in section 6-1b.

2.Use a crescent or standard 3/4" wrench to loosen the thermometer mounting nut that holds the thermometer in place on the back of the front panel. (Fig. 16)

3.Remove the nut, washer and retaining bracket and pull thermometer out the front of the panel.

4.Replace retaining bracket and insert new thermometer into opening.

**NOTE: Align thermometer so that the 150° reading will be straight up when the front panel is replaced and the heating module is flipped over. (Fig. 17)

5.Replace and tighten washer and nut on rear of front panel. DO NOT OVER TIGHTEN!

6.Replace the front panel (section 6-1b).

6-1g.Replacing the power cord for a CA70 unit.

Required: Medium (6”) phillips screwdriver, Medium (6") flathead screwdriver, Wiring markers (color or number codes), Electrical tape, Wiring diagram for CA70 (see step 10)

1.Remove top mounted heating module and front panel as found in sections 6-1aand6-1b.

2.Mark all the wires connected to the power cord with a color code or number to make proper re-connectioneasy. (Fig.

18).

3.Turn the top mounted heating unit over so that the elbow connector for the power cord is up. Free the green ground wire by grasping the nut with fingers or pliers (under front overhang of the heating module) and remove the screw from the exposed surface of the module with a medium (6") phillips screwdriver. (Fig. 19).

4.Free the other two power cord wires by removing the two wire nuts that connect them.

5.Remove elbow connector that secures power cord into the heating module by grasping the nut holding the connector (under the overhang of the heating module). Rotate the nut to loosen and remove the elbow from the module. (Fig. 20)

6.Remove the two screws that secure the power cord into the compression end of the elbow connector with a medium (6”) flathead screwdriver. Pull gently to free power cord from the elbow connector. (Fig. 21)

7.Insert new power cord into elbow connector and replace compression screws. Tighten screws to secure power cord into connector.

**WARNING: Replace only with a BEVLES power cord properly rated for your unit.

8.Insert new wires through opening in the heating module and reattach elbow connector.

9.Reattach green ground wire to module.

10.Reconnect power cord wires using wire nuts and wiring diagram. Re-tapeover wire nuts and wires. (Diagram 2)**WARNING: Severe damage can be caused to your unit by improperly connecting wiring.

11.Replace the front panel and top mounted heating module (sections 6-1a.and6-1b).

11

Figure 20

Figure 21

Figure 22

Figure 23

6-1h.Replacing the power cord for a CA43.

Required: Medium (6”) phillips screwdriver, Medium (6") flathead screwdriver, Wiring markers (color or number codes), Electrical tape , Wiring diagram for CA43(see step 10)

1.Remove the back panel of the module by removing the five phillips head screws and gently lifting out the back panel. Lay the panel on a clean work surface. (Fig. 22)

 

 

 

(4)

(5)

(0)

 

 

 

 

 

 

 

 

 

 

 

Klixon

 

(1)

Cooling

 

 

 

 

 

 

Fan

(Grd)

 

 

Thermostat

 

 

 

 

 

 

 

(2)

 

 

 

 

 

 

 

(3)

 

 

 

 

 

 

 

Power Cord

 

 

(0)

(5)

(0)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heating

 

 

 

(1)

 

 

 

(4) Element

(1)

 

 

 

Fan

 

 

 

 

 

 

 

 

Thermostat

 

Blower

 

 

 

 

 

 

(0)

(1)

 

 

 

 

(5)

(1)

 

 

(0)

(1)

 

 

 

 

Power

(2)

(3)

 

 

Thermostat

Indicator Lamp

Power Switch

 

Indicator Lamp

Diagram 2

2.Mark all the wires connected to the power cord with a color code or number to make proper re-connectioneasy. (Fig. 23)

3.Free the green ground wire by grasping the nut with fingers or pliers (inside the back panel of module) and remove screw from the outside surface of the panel with a medium (6") phillips screwdriver. (Fig. 24)

4.Free the other two power cord wires by removing the two wire nuts they are attached to.

5.Remove elbow connector that secures power cord onto the back panel. While grasping the nut (on the inside surface of the panel) and holding the connector (on the outside surface of the panel), rotate the nut to loosen and remove the elbow from the panel. (Fig. 25) .

6.Remove the two screws that secure the power cord into the compression end of the elbow connector with a medium (6”) flathead screwdriver. Pull gently to free power cord from the elbow connector. (Fig. 26)

7.Insert new power cord into elbow connector and replace compression screws. Tighten screws to secure power cord into connector.

*"WARNING: Replace only with a BEVLES power cord properly rated for your unit.

8.Insert new wires through opening in back panel and reattach elbow connector.

9.Reattach green ground wire to back panel.

10.Reconnect power cord wires using wire nuts and wiring diagram. Retape over wire nuts and wires. (Diagram 3) **WARNING: Severe damage can be caused to your unit by improperly connecting wires.

11.Replace the back panel using the five phillips head screws.

12

 

Figure 24

 

 

Figure 25

 

 

 

 

Figure 26

 

 

 

(0)

 

(0)

(1)

 

 

(0)

(5)

 

 

 

(1) Cooling

(5) (1)

 

 

 

 

 

(0)

(Grd)

 

 

Fan

Power

(0)

(1)

 

 

 

(4)

(5)

 

Indicator Lamp

 

 

Thermostat (1) Fan

 

 

 

(2)

(3)

(2)

 

 

 

 

 

 

(3)

Heating

 

Klixon

Thermostat

 

 

Power Switch

 

Blower

 

Indicator Lamp

 

 

 

Power Cord

(4) Element (1)

Thermostat

 

 

 

 

 

 

 

 

 

 

 

 

 

Diagram 3

 

 

 

Figure 27

 

Figure 28

 

6-1i.Replacing the thermostat for a CA70.

Required: Small flathead screwdriver, Medium (6") flathead screwdriver, Medium (6") phillips screwdriver, Wiring markers (color or number codes), Electrical tape, Wiring diagram for thermostat (see step 9)

1.Remove top mounted heating module and front panel as found in sections 6-1aand6-1b.

2.Mark all the wires connected to the thermostat with a color code or number to make proper re-connectioneasy. (Fig. 27)

3.Remove thermostat dial from front panel by rotating the dial to expose the set screw and reversing the set screw with a small flathead screwdriver. (Fig. 28)

4.Remove the two screws holding the bezel (chrome ring) behind the thermostat dial with a medium (6”) phillips screwdriver. Carefully pull thermostat away from the rear of the front cover.

Figure 29

Figure 30

5.Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear screws with a medium (6” flathead screwdriver. (Fig. 29)

6. Remove the two screws securing the clips that attach the copper thermostat probe to the fan blower. Use a medium flathead screwdriver. (Fig. 30)

13

Figure 31

Figure 32

7.Pull the copper thermostat probe and tubing from the fan blower motor assembly area through the opening to the front cover (it may be necessary to feed the probe, into the bottom of the assembly area under the fan blower to achieve the correct angle). (Fig. 31)

**NOTE: DO NOT bend or kink the copper tubing when replacing the thermostat probe.

8.Disconnect wires from rear of thermostat by reversing screw terminals with a flathead screwdriver.

9.Connect wires to the rear of a new thermostat unit using the thermostat wiring diagram for CA70 units. Re-tapeover wire nuts and wires. (Diagram 4)

10.Attach new thermostat to rear of front panel and bezel to the front of panel with the two phillips screws.

**NOTE: The tops of the terminals should face down (toward the actual top of the heating module). (Fig. 32)

11.Carefully guide new copper probe and tubing through the opening to fan blower motor housing and reattach probe clips with two flathead screws. (Fig. 31)

**NOTE: DO NOT kink or bend the copper probe or tubing.

12.Replace fan blower motor assembly cover with two front and two rear flathead screws. Do not over tighten.

13.Replace thermostat dial, tightening set screw securely.

14.Replace top mounted heating module and front panel (sections 6-1aand6-1b).

 

 

 

 

 

 

 

 

(0)

 

 

 

 

 

 

(0)

 

(1)

 

 

 

 

(0)

 

 

(5)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(1) Cooling

(5)

 

(1)

Power

(0)

 

 

 

 

 

 

 

(1)

 

 

 

(0)

 

(Grd)

 

 

 

 

 

 

 

 

 

 

 

 

 

Fan

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(4)

(5)

 

 

 

 

 

 

 

Indicator Lamp

(2)

 

 

 

 

 

 

 

 

 

(3) Thermostat (1)

Fan

(2)

 

 

 

 

 

 

 

 

Thermostat

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Blower

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(3)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power Switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heating

 

 

Klixon

Indicator Lamp

 

 

 

 

 

 

 

Power Cord

(4)

Element

(1) Thermostat

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Diagram 4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6-1jReplacing the thermostat for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CA43 units.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Required: Small flathead screwdriver,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Medium

(6”)

flathead

 

screwdriver,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Medium

(6”)

 

phillips

 

screwdriver,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wiring markers (color or number

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

codes), Electrical tape, Wiring diagram

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

for thermostat (see step 11)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Remove top mounted heating

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

module and front panel as

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

found in sections 6-1aand6-1b.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Mark all the wires connected to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 33

 

 

 

 

 

 

 

 

 

 

Figure 34

 

the power cord with a color

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

code or number to make proper re-connectioneasy. (Fig. 33)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.Remove thermostat dial from front panel by rotating the dial to expose the set screw and reversing the sat screw with a small flathead screwdriver. (Fig. 34)

4.Remove the two screws holding the bezel (chrome ring) behind the thermostat dial with a medium (6”) phillips screwdriver. Carefully pull thermostat away from the rear of the front cover.

5.Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear screws with a medium (6”) flathead screwdriver. (Fig. 35)

6.Pry off fan blower housing cover (with a flathead screwdriver, if necessary). Without disconnecting wires, set cover on a clean work area. (Fig. 36)

7.Remove four screws (two at each end) holding fan blower motor bracket in place with a medium flathead screwdriver and gently lift bracket to expose mounting clips for the copper thermostat probe. (Fig. 37)

14

Figure 35

Figure 36

8.Remove the two screws and nuts securing the clips that attach the copper thermostat probe to the motor bracket. Use a medium flathead screwdriver. (Fig. 38)

9.Pull copper probe and tubing from fan blower motor area through the opening to the front panel.

**NOTE: DO NOT bend or kink the copper tubing when replacing the thermostat probe.

10.Disconnect wires from rear of thermostat by reversing screw terminals with a flathead screwdriver.

11.Connect wires to the rear of a new thermostat unit using the thermostat wiring diagram for CA43 units. Re-tapeover wire nuts and wires. (Diagram 5)

12.Attach new thermostat to rear of front panel and bezel to the front of panel with the two phillips screws.

**NOTE: The tops of the terminals should face down (toward actual top of the heating module). (Fig. 39)

13.Carefully guide new copper probe and tubing through opening to fan blower motor area and reattach probe clips to motor bracket with two flathead screws.

**NOTE: DO NOT kink or bend the copper probe or tubing.

14.Replace fan blower motor bracket with two phillips screws front and two rear.

15.Replace fan blower motor housing cover, carefully guiding the wires to prevent damage.

16.Replace fan blower motor assembly cover with two front and two rear flathead screws.

17.Replace thermostat dial, tightening set screw securely.

18.Replace top mounted heating module and front panel (sections 6-1a. and6-1b).

 

 

 

 

 

Figure 37

 

Figure 38

 

Figure 39

 

 

 

 

 

 

 

 

 

(0)

 

 

(0)

(1)

 

(0)

(5)

 

 

 

(1)

Cooling

 

 

 

 

 

 

 

(Grd)

 

 

Fan

 

Power

 

 

 

 

 

 

 

 

Indicator Lamp

 

Thermostat

 

 

 

 

 

 

 

 

(2)

(4)

(5)

 

(5)

(1)

 

 

 

 

 

 

 

 

 

(3)

 

 

 

 

 

 

 

 

(0)

 

Power Cord

 

Klixon

 

 

 

(0)

(1)

 

 

 

 

Thermostat

 

Thermostat

(2)

(3)

 

(1)

Fan

 

 

 

 

Indicator Lamp

 

 

 

 

 

 

Power Switch

 

 

Blower

Heating

 

 

 

 

 

 

 

(4) Element

(1)

 

 

 

 

 

 

 

 

 

Diagram 5

15

Figure 40

Figure 41

Figure 42

6-1k.Replacing the fan blower motor assembly.

Required: Medium (6") flathead screwdriver, Medium (6”) phillips screwdriver, Crescent or standard wrench, Wiring markers (color or number codes), Electrical tape

1.Remove top mounted heating module as found in section 6-1a.

2.Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear screws with a medium (6”) flathead screwdriver. (Fig. 40)

3.Pry off fan blower housing cover (with a flathead screwdriver, if necessary). Without disconnecting wires, set cover on a clean work area. (Fig. 41)

4.Mark all the wires connected to the fan blower motor(s) with a color code or number to make proper re-connectioneasy. (Fig. 42)

5.Remove wire nuts and set cover aside.

6.For CA70 units, remove the two screws securing the clips that attach the copper thermostat probe to the fan blower. Use a medium flathead screwdriver. Free the copper probe and carefully set out of the way. (Fig. 43)

**NOTE: DO NOT kink or bend copper tubing or probe. Remove four screws (two at each end) that hold the fan blower motor bracket in place. Use a medium flathead screwdriver.

7.For CA43 units, remove four screws (two at each end) that hold the fan blower motor bracket in place. Use a medium flathead screwdriver. Gently lift bracket to expose mounting clips for the copper thermostat probe. Remove the two screws securing the clips holding the copper thermostat probe with medium flathead screwdriver. Free copper probe and carefully set out of the way. (Figs. 44 &45)

**NOTE: DO NOT kink or bend copper tubing or probe.

8.Remove fan blower motor bracket with fan blower motor(s) still attached and place entire assembly on a clean work space. (Fig. 46)

9.Remove fan blower motor(s) from mounting bracket by removing four securing screws with a medium (6”) flathead screwdriver.

10.Mount new motor(s) in same position with the four phillips screws.

**NOTE: All replacement motors will have two drilled holes in the blower portion - these are irrelevant unless you are replacing the front motor on a CA70 and will not affect performance in any application.

11.Replace the fan blower motor bracket in heating module with large flange up. (Fig. 46) .

 

 

 

 

 

Figure 43

 

Figure 44

 

Figure 45

16

Figure 46

Figure 47

Figure 48

Figure 49

12.For CA70 units, secure fan blower motor bracket with the four phillips screws. Reattach thermostat probe clips with two flathead screws.

**NOTE: DO NOT kink or bend the copper probe or tubing.

13.For CA43 units, reattach thermostat probe clips with two flathead screws.

**NOTE: DO NOT kink or bend the copper probe or tubing. Secure fan blower motor bracket with the four flathead screws.

14.Reconnect existing wires to new motor wires. It is not important which new wire is matched with which existing wire group. Re-tapeover wire nuts and wires.

15.Replace fan blower motor housing cover, carefully guiding the wires to prevent damage.

16.Replace fan blower motor assembly cover with two front and two rear flathead screws.

17.Replace top mounted heating module (section 6-1a).

6-1l.Replacing heating element.

Required: Medium (6") flathead screwdriver, Medium (6") phillips screwdriver, Crescent wrench, General Electric 1209 caulking

1.Remove top mounted heating module as found in section 6-1a.

2.Remove four screws that secure the air deflector housing (on your right as you are facing the front of heating module) to the module with a medium (6”) flathead screwdriver.(Fig. 47)

3.Gently lift the air deflector housing to access the nuts connecting wires to the heating element. Remove those nuts and washers to free the wires. (Fig. 48)

4.Remove air deflector housing" and place on a clean work area.

5.Remove four screws securing the heating element brackets to the ceramic insulators with a medium (6") flathead screwdriver. (Fig. 49)

6.Slide brackets off the old element and discard the old element.

7.Slide brackets (large one first) over the connector end of the new heating element. (Fig. 50)

8.Reconnect heating element brackets to the ceramic insulators with the four phillips screws. Do not over tighten.

9.Return air deflector housing to the heating module and reconnect wiring (it is not important which way you match the wires to the new element). (Fig. 51)

10.Caulk openings where the heating element enters the air deflector housing with GE 1209 caulking. (Fig. 52)

11.Reconnect air deflector housing to heating module with the four flathead screws.

12.Replace top mounted heating module (section 6-1a).

 

 

 

 

 

Figure 50

 

Figure 51

 

Figure 52

 

 

 

 

 

17

Figure 53

Figure 54

Figure 55

Figure 56

Figure 57

6-1m.Replacing theHigh-temperaturesafety thermostat.

Required: Medium (6”) flathead screwdriver, Medium (6") phillips screwdriver, Crescent wrench

1.Remove top mounted heating module as found in section 6-1a.

2.Remove four screws that secure the air deflector housing (on your right as you are facing the front of heating module) to the module with a medium (6”) flathead screwdriver.

3.Gently lift the air deflector housing to access the nuts and connecting wires to the high temperature safety thermostat. Remove those nuts and washers to free the wires and the thermostat.

4.Attach the new high-temperaturethermostat and reconnect the new wires.

5.Reconnect air deflector housing to heating module with the four flathead screws.

6.Replace top mounted heating module (section 6-1a).

6-1n. Replacing the top mounted heating module seal (gasket).

Required: Razor blade, General Electric 1209 caulking

1.Remove top mounted heating module as found in section 6-1a.

2.Razor blade old gasket and foam tape off of the heating module. (Fig. 53)

**NOTE: Remove all caulking and material carefully. A good seal requires a clean surface.

3.Set new gasket into place using double-facefoam tape (included with new gasket) to attach new gasket to module. (Fig. 54)

4.Caulk inner and outer edges of new gasket with GE 1209 caulking. Allow caulking to dry for at least 45 minutes. (Fig. 55)

5.Replace top mounted heating module (section 6-1a).

6.1o. Replacing the fan blower cooling fan for CA43 units.

Required: Medium (6”) flathead screwdriver, Medium (6”) phillips screwdriver, Wiring markers (color or number codes), Electrical tape

1.Remove the back panel of the module by removing the five flathead screws and gently removing the back panel. Lay the panel on a clean work surface.

2.Remove four screws inside the back panel that secure the cooling fan to the back panel with a medium (6”) flathead screwdriver. Save spacers for reuse. (Fig. 56)

3.Mark all the wires connected to the cooling fan with a color code or number to make proper re-connectioneasy. (Fig. 57)

4.Remove wire nuts and retain wire sleeve for reuse. Discard old cooling fan (if under warranty and requested by BEVLES, send fan and Return MaterialAuthorization form to the factory for credit).

5.Slip reserved wire sleeve onto the wires of the new cooling fan.

6.Connect new cooling fan wires to existing wires. It is not important which way you match the new wires.

7.Carefully insert nylon spacers between the cooling fan and back panel. Connect new fan to the back panel with the four flathead screws. (Fig. 56)

8.Replace back panel with the five flathead screws.

9.Replace top mounted heating module (section 6-1a).

18

7. REPLACEMENT PARTS

Use only BEVLES replacement parts in repairing your unit. This assures you of continued high quality performance.

7-1HOW TO ORDER

To determine the parts you need:

1.Use the drawings found in section 7-5and refer to the parts list in section7-6to determine the BEVLES part numbers you need.

2.Note the model number, serial number and the date of manufacture of your unit from the serial number label (located in the top right front comer of the right side of the unit).

3.Call the BEVLES manufacturing facilities at (214) 421-7366or (800)441-1601(outside of Texas andAlaska).

7-2PRICES

Your distributor can provide you with a current price list for replacement parts. Or, call the BEVLES manufacturing facilities for the most recent prices.

7-3SHIPPING

Common parts are in-stockfor immediate processing. Normally, replacement parts will be shipped within two working days.

7-4WARRANTY

Replacement parts are fully covered by the parts provisions of the BEVLES quality assurance warranty at the front of this manual.

7-5PARTS DRAWINGS

Exploded drawings provided for:

Model Number

Drawing Number

CA70-CV16,CV16HW, CV32. CV32HW, CVMP12, CVMP15

7-5a.Heating Module

 

7-5b.Cabinet Assembly

 

 

CA43-CV7,CV7HW, CV13,..CV13HVV, CVMP6, CVMP7

7-5c.Heating Module

 

7-5d.Cabinet Assembly

 

 

19

CA70 MODELS

7-5a.Heating Module for CA70 Models

 

Drawing

 

 

 

 

Reference

Description

 

Number

 

1

Heating Module

 

1A

Heating Module, MP

 

1B

Heating Module, HW

2

Front Control Panel

 

2A

Front Control Panel, MP

3Sheet Metal Screw, #10 x ½ s/s phillips

4Flat Washer, AN960-ClOLsls

5Thermometer, 6" 50-250°F

6Thermometer Mounting Bracket

7Nut, Thermometer Mounting Bracket

8Indicator Lamp, Solico 5SF3LRN1-6

9Thermostat, 50-250°F

10Mounting Screw, #6-32x 1/4" rd. hd.s/s phillips

11Knob, Thermostat 50-250°F

12Socket Set Screw, Thermostat Knob #8-32

13Clamp, Thermostat Probe

14Power Switch, LTIGK-6S-WH-NBL

15Blower Motor

16Mounting Screw, #10-24x 1/2" sls phillips

17Lockwasher, #10 s/s internal tooth

18Nut, #10-24hex s/s

20Motor Air Duct Cover

21Water Pan Slide

22Heating Element, 1500W, 120V

22A

Heating Element, 1800W, 120V (MP or HW Models)

23Front Clip, 0.81" x 4.875"

24Rear Clip, 0.81" x 5.87" .

25Ceramic Insulator

26Screw, #6-32x 1/4" sls phillips

27Lockwasher, #6 s/s

28Power Cord, 14-3SO

28A Power Cord, 12-3SO (MP or HW Models)

29Elbow Connector

30High-Temperature(Klixon)Thermostat, 120V/240V

31Lockwasher, Elbow Connector

32Elbow Connector Nut

33Air Flow Cover Extension, MP

34Motor Housing Cover

34A Motor Housing Cover, MP

7-5b.Cabinet Assembly for CA70 Models

Drawing

Reference Description

Number

1 Heating Module

1A Heating Module, MP

1B Heating Module, HW

2 Cabinet Assembly

2A Cabinet Assembly, MP

3 Dutch Door, Upper

3A Dutch Door, Upper for MP

4 Dutch Door, Bottom

4A Dutch Door, Bottom for MP

5 Full Door

5A Full Door, MP

6Door Hinge, 2”

7Cabinet Hinge, 3”

8Hinge Pin, 5/16" x 5" rod

9Machine Screw, 1/4"-20x 1/2” phillips

10Latch

11Latch Strike

12Latch Pin, 5/16” x 8.5" rod

13Latch Spring #CDL5019

14Wiper Blade

14A Wiper Blade, MP

15Wiper Blade Retainer 15A Wiper Blade Retainer, MP

16Thumb Screw, bakelite

17Air Duct Assembly, upper (CV32)

18Air Duct Assembly, lower (CV32)

19Button, aluminum #10-23-75R

20Sheet Metal Screw, T/H #8 x 1 1/4" phillips

21Water Pan

22Baffle, 22 ga. 7' x 8.5"

23Door Gasket, magnetic 21.5” x 57"

23A Door Gasket, magnetic 26” x 57”, MP

24Gasket Retainer, top outer 22.37” 24A Gasket Retainer, top outer 26.87”, M

25Gasket Retainer, bottom outer 22.37

25A Gasket Retainer, bottom outer 26.87”, MP

26Gasket Retainer, side outer 58.37”

27Sheet Metal Screw, #6 x 3/4" hex head

28Caster, 5' with brake

29Caster, 5' without brake

30Nut, hex 5/16" -18

31Lockwasher, 5/16" internal tooth .

32Bolt, hex 5/16" -18x 1 1/4"

33Air Duct Assembly, upper (Cv16)

34Air Duct Assembly, lower (Cv16)

35Air Duct Assembly, upper (CVMP12)

36Air Duct Assembly, lower (CVMP12)

37Wire Hanger, MP

38Air Duct Assembly, upper (CVMP15)

39Air Duct Assembly, lower (CVMP15)

40Extruded Runner, MP

20