Axor 34133XX1 34213XX1 User Manual

Size:
2.46 Mb
Download

Installation Instructions / Warranty

Citterio M

34133XX1

Citterio M

34213XX1

Axor Citterio M widespread lavatory faucet 34133XX1 Axor Citterio M widespread bidet faucet 34213XX1

34213XX1 34133XX1

Technical Information

Recommended water pressure

14.7 - 72.5 psi

Max. water pressure

145 psi

Recommended hot water temp.

120 - 140 F*

Max. hot water temp

165 F*

Hole size in mounting surface

 

valves

1-1/4"

spout

1 3/8"

Max. mounting surface depth

1 3/8"

Flow rate

2.2 gpm

*Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.

Installation Considerations

For best results, Hansgrohe recommends that this unit be installed by a licensed, professional plumber.

Please read over these instructions thoroughly before beginning installation. Make sure that you have all tools and supplies needed to complete the installation.

This faucet can be used with a continuous flow water heater if the flow pressure is at least 20 psi. For best service, the hot and cold supplies should be at equal pressure.

This faucet requires 1/2" supply lines (not included).

Installation

Install the friction washer and fiber washer on the valve. Push the valve up through the hole in the mounting surface. Install the sealing ring, escutcheon, and nut.

Rest the valve assembly on the mounting surface (1). Tighten the screws (2).

Push the handles into place (3).

3

2

1

Push the spout shank up through the mounting surface

(1).

Install the sealing ring, escutcheon, and shaft fastening ring (2).

The notch on the shaft fastening ring and the notch on the shank must face away from the basin.

Install the fiber washer, friction washer, and mounting nut (3). Tighten the mounting nut.

2

1

Check the alignment of the handles.

If one is not aligned, pull it off (1), turn it slightly (2), and reinstall it (3).

Install the glide ring and the o-ring.

2

3

1

Lubricate spout the o-ring.

Push the spout into place.

Tighten the spout screw with a 2 mm Allen wrench.

Tighten the mounting nut screws.

Install the drain pull rod.

Thread the connecting hoses into the spout shank by hand.

Connect the hoses to the valves with the compression fittings. Tighten the fittings using two wrenches. Do not allow the hoses to twist.

Install the hot and cold supply lines (not included).

Install the pop-updrain.

off

on

Install the pop-updrain

Remove the plunger assembly.

Unscrew the drain outlet flange from the tee.

Unscrew the tailpiece from the tee. Wrap the threads with plumbers’ thread tape and replace.

Install the white, flexible sealing gasket to the flange. Place it in the sink outlet.

From under the sink, install the black mack gasket, white friction ring and retainer nut to the flange. Do not tighten the nut against the bottom of the sink at this time.

plunger

height adjuster

flange

sealing gasket

Thread the tee and tailpiece to the flange. The pivot must face the faucet. If necessary, turn the drain assembly.

Tighten the retainer nut.

Place the plunger assembly in the drain.

Install the horizontal rod so that the end goes through the loop in the bottom of the height adjuster.

Install and hand tighten the pivot ball nut.

Attach the swivel connector to the end of the horizontal rod.

mack gasket

pull rod

friction ring

retainer nut

tee

pivot ball nut

horizontal rod

tailpiece swivel connector

Attach the swivel connector to the end of the pull rod. Position as desired and tighten with a small, flat bladed screwdriver.

Cleaning (34133 only)

If the flow of water diminishes over time, unscrew the aerator using the service key.

Rinse the aerator with clear water.

Reinstall the aerator. Tighten it with the service key.

Replacement Parts

 

16

4

 

1

 

30x1.5

2

 

6

 

 

3

11

12

 

5

9

7

8

17

10

15

13

14

1

aerator

8926000

2

handle

34095XX0

3

color-ringset

8927000

4

spout

8928XX0

5

nut

8929XX0

6

pull rod

57XX0

7

cold cartridge

4008000

8

hot cartridge

4009000

9

fixation set

13961000

10

connection hose

4071001

11

handle fixing set

8932000

12

flange

8930XX0

13

aerator

7360XX0

14

ball joint

7362XX0

15

spout

8931XX0

16

aerator service key

8987000

17

compression fittings (pr.)

88513000

XX = color

 

00

= chrome

 

82

= brushed nickel

 

Cleaning Recommendation for Hansgrohe Products

Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.

Cleaning Materials for Faucets and Showers

Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points when cleaning faucets and showers:

Only use cleaning materials which are explicitly intended for this type of application.

Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause considerable damage.

Never mix one cleaning material with another.

Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads, or micro fiber cloths.

Cleaning Instructions for Faucets and Showers

Please follow the cleaning material manufacturer’s instructions. In addition, pay attention to the following points:

Clean the faucets and showers as and when required

Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the cleaner on the fixture longer than necessary.

Regular cleaning can prevent calcification.

When using spray cleaners, spray first onto a soft cloth or sponge. Never spray directly onto the faucet as droplets can enter openings and gaps and cause damage.

After cleaning, rinse thoroughly with clean water to remove any cleaner residue.

Important

Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using. Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage.

Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty.

Limited Lifetime Consumer Warranty

This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada.

WHO IS COVERED BY THE WARRANTY

This warranty extends to the original consumer purchaser only. This warranty is non-transferable.WHAT IS COVERED BY THE WARRANTY

This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made, Hansgrohe may elect to refund the purchase price in exchange for the return of the product.

LENGTH OF WARRANTY

Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If you are a consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends for as long as you own the product and the home in which the product is originally installed. If you purchased

10