Avaya 4606 User Manual

Size:
581.76 Kb
Download

Static Addressing Installation

3.Enter the Gatekeeper IP address followed by the# button. The following message displays:

CallSvPort=nnnnn

New=_

where nnnnn is the value of the Management Complex (media server/gatekeeper)transport-layerport number, a value between 0 and 65535.

4.Enter the appropriate value for the Port Number followed by the# button. The following message displays:

Router=nnn.nnn.nnn.nnn

or

 

nnn.nnn.nnn.nnn

New=_

 

 

Router=_

 

 

 

 

where nnn.nnn.nnn.nnn is the value of the gateway/router IP address.

5.Enter the Gateway router IP address followed by the# button. The following message displays:

Mask=nnn.nnn.nnn.nnn

or

 

nnn.nnn.nnn.nnn

New=_

 

 

Mask=_

 

 

 

 

where nnn.nnn.nnn.nnn is the value of the IP netmask.

6.Enter the IP netmask followed by the# button. The following message displays:

FileSv=nnn.nnn.nnn.nnn

or

 

nnn.nnn.nnn.nnn

New=_

 

 

FileSv=_

 

 

 

 

where nnn.nnn.nnn.nnn is the value of the TFTP server IP address.

7.Enter the TFTP Server IP address followed by the# button.

One of the following texts displays left-justifiedat the top of the display, depending on the current status of 802.1Q:

If 802.1Q is off:

802.1Q=off

 

1=on #=OK

If 802.1Q is on:

 

 

802.1Q=on

 

0=off #=OK

 

 

8.Press the 1 or0 button to turn802.1Q on or off respectively. The display is updated to show the current status of 802.1Q.

Issue 2.2 April 2005 41

Local Administrative Options

9.Press the # button to continue the procedure without changing the displayed status of 802.1Q

The following text displays left-justifiedat the top of the display:

VLAN ID=dddd

New=_

where dddd is the value of the 802.1 VLAN ID.

10.Enter a valid value between 0 and 4094 for the new value of the 802.1 VLAN ID. The following message displays:

VLAN test=ddd

New=_

where ddd is the value of theDHCPOFFER wait period.

11. Enter a valid value between 0 and 999 for the new value of the DHCPOFFER wait period.

The following message displays:

Save new values? *=no #=yes

12.Press the # button to save the new values you entered. The following message displays:

New values being saved

Once the new values are stored, the telephone is reset.

If a new boot program is downloaded from the TFTP server after you enter static addressing information, you must reenter your static addressing information.

42 4600 Series IP Telephone Release 2.2 Installation Guide

QoS Option Setting

QoS Option Setting

Use the following procedure to set Quality of Service (QoS) options.

Note:

The 4601 IP Telephone does not support QoS Option Setting.

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 7 6 7 # (Mute Q O S #)

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630 and 4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

The following text displays left-justifiedat the top of the display:

L2 audio=d

New=_

where d is the value of the 802.1 audio parameter.

2.Enter a valid value between 0 and 7 for the new value of the 802.1 audio parameter. The following text displaysleft-justifiedat the top of the display:

L2 signaling=d

New=_

where d is the value of the 802.1 signaling parameter.

3.Enter a valid value between 0 and 7 for the new value of the 802.1 signaling parameter. The following text displaysleft-justifiedat the top of the display:

L3 audio=dd

New=_

where dd is the value of the Differential Services audio parameter.

Issue 2.2 April 2005 43

Local Administrative Options

4.Enter a valid value between 0 and 63 for the new value of the Differential Services audio parameter.

The following text displays left-justifiedat the top of the display:

L3 signaling=dd

New=_

where dd is the value of the Differential Services signaling parameter.

5.Enter a valid value between 0 and 63 for the new value of the Differential Services signaling parameter.

If no new values were entered during this procedure, the following text displays left-justifiedat the top of the display:

No new values. #=OK

6.Press # to terminate the procedure.

If new values were entered during this procedure, the following text displays left-justifiedat the top of the display:

Save new values? *=no #=yes

7.Press the * button to terminate the procedure, or the# button to save the new values. If you press the# button, the following text displays:

New values being saved

The new values are saved, and the user interface is restored to its previous state.

44 4600 Series IP Telephone Release 2.2 Installation Guide

Interface Control

Interface Control

Use the following procedure to set or change the interface control value.

Note:

The 4601, 4602, and 4690 Telephones do not have Ethernet PC interfaces, so this procedure does not apply to those phones.

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 4 6 8 # (Mute I N T #)

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630 and 4630SW IP Telephones do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

2.For telephones that support an Infrared (IR) interface (4620 and 4620SW only), proceed directly to Step 7. If the telephones have an internal Ethernet switch, proceed to Step 3.

After entry of the command sequence, telephones with an internal Ethernet switch display the following text, depending on the current interface control value:

PHY1=status

*=change #=OK

where status is the value of PHY1STAT, defined as:

Status is auto when PHY1STAT = 1

Status is 10Mbps HDX when PHY1STAT = 2

Status is 10Mbps FDX when PHY1STAT = 3

Status is 100Mbps HDX when PHY1STAT = 4

Status is 100Mbps FDX when PHY1STAT = 5

Issue 2.2 April 2005 45

Local Administrative Options

3.To change the PHY1 value, press *.

Depending on the current value, the next sequential valid PHY1 value is selected and displayed as the status. For example, if the current value is 10Mbps HDX (2), pressing * changes the value to 3 (10Mbps FDX). If the current value is 100Mbps FDX (5), pressing* changes the value to 1 (auto).

If a value different from the current PHY1STAT value is entered, the following text displays left-justifiedat the top of the display:

Save new value?

*=no #=yes

4.Press the * button to terminate the procedure, or the # button to save the new value. If you press the# button, the following text displays:

PHY2=status

*=change #=OK

where status is the value of PHY2STAT, defined as:

Status is disabled when PHY2STAT = 0

Status is auto when PHY2STAT = 1

Status is 10Mbps HDX when PHY2STAT = 2

Status is 10Mbps FDX when PHY2STAT = 3

Status is 100Mbps HDX when PHY2STAT = 4

Status is 100Mbps FDX when PHY2STAT = 5

5.To change the PHY2 value, press *.

Depending on the current value, the next sequential valid PHY2 value is selected and displayed as the status. For example, if the current value is 10Mbps HDX (2), pressing * changes the value to 3 (10Mbps FDX). If the current value is 100Mbps FDX (5), pressing* changes the value to 0 (disabled).

The following text displays left-justifiedat the top of the display:

Save new value? *=no #=yes

46 4600 Series IP Telephone Release 2.2 Installation Guide

Interface Control

6.Press the * button to terminate the procedure, or the# button to save the new values. If you press the# button, the following text displays.

New value being saved

The new values are saved and a restart occurs automatically. The user interface is restored to its previous state.

7.For telephones with an IR interface, after entry of the command sequence, one of the following texts displays, depending on the current value of the IRSTAT:

If IRSTAT=1:

IR=enabled

 

0=disable #=OK

If IRSTAT=2:

 

 

IR=disabled

 

1=enable #=OK

 

 

8.Press the 1 or0 button to enable or disable the IR interface respectively, or press the# button to leave the current value. The following text displaysleft-justifiedat the top of the display:

Save new value? *=no #=yes

9.Press the * button to terminate the procedure, or the# button to save the new values. If you press the# button, the following text displays.

New value being saved

The new values are saved, and a restart occurs automatically. The user interface is restored to its previous state.

Issue 2.2 April 2005 47

Local Administrative Options

Group Identifier

Use the following procedure to set or change the Group Identifier.

Note:

Perform this procedure only if the LAN Administrator instructs you to do so. The 4601 IP Telephone does not support the Group Identifier.

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 4 7 6 8 7 (Mute G R O U P)

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630/4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

The following text displays left-justifiedat the top of the display:

Group=ddd

New=_

where ddd is the Group value.

2.Enter a valid Group value(0-999).

If a value different from the current Group value is entered, the following text displays left-justifiedat the top of the display:

Save new value?

*=no #=yes

3.Press the * button to terminate the procedure, or the# button to save the new value. If you press the# button, the following text displays:

New value being saved

The new value is saved and the user interface is restored to its previous state.

48 4600 Series IP Telephone Release 2.2 Installation Guide

Computer-TelephonyIntegration (CTI) Enable/Disable

Computer-TelephonyIntegration (CTI) Enable/Disable

Use the following procedure to enable or disable the CTI interface.

Note:

The default for the CTI interface is enabled.

The 4601, 4602, 4602SW, and 4690 do not support the CTI interface.

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 2 8 4 # (Mute C T I #)

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630/4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

One of the following texts displays left-justifiedat the top of the display, depending on the current value of the CTI:

If CTI=manual:

CTI=manual

 

0=Off #=OK

If CTI=disabled:

 

 

CTI=disabled

 

1=Manual #=OK

 

 

2.Press the 1 or0 button to enable or disable the CTI interface respectively, or the# button to leave the current value. The following text displaysleft-justifiedat the top of the display:

UDP Port=497xx

New=_

where 497xx is the value of the UDP port for CTI.

3.Enter a valid value between 49714 and 49721, inclusive for the UDP Port for CTI. The following text displaysleft-justifiedat the top of the display:

Save new value? *=no #=yes

Issue 2.2 April 2005 49

Local Administrative Options

4.Press the * button to terminate the procedure, or the# button to save the new values. If you press the# button, the following text displays.

New value being saved

The new values are saved, and the user interface is restored to its previous state.

Site-SpecificOption Number Setting

! CAUTION:

Do not perform this procedure if you are using static addressing. Perform this procedureonly if you are using DHCPand the LAN administrator instructs you to do this.

Use the following procedure to set the Site-SpecificOption Number (SSON).

1.While the phone is on-hookand idle, press the following sequence of keys on the faceplate of the telephone:

Mute 7 7 6 6 # (Mute S S O N #)

Note:

Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. The 4630/4630SW IP Telephones and the 4690 IP Conference Telephone do not have a dedicatedHold button. For all other 4600 Series IP Telephones, pressing theHold button instead of theMute button also works.

All IP telephones except the 4601 display the following text left-justifiedat the top of the display:

SSON=ddd

New=_

where ddd is the value of SSON.

Because it does not have a display, the 4601 IP Telephone’s Call Appearance Line indicators wink out the current SSON value. Call Appearance Line a represents the SSON’s first digit. Call Appearance Lineb represents the SSON’s second digit, and Call Appearance Linea represents the SSON’s third digit. For each digit, the applicable indicator winks the number of times represented by the current SSON value 600 milliseconds on, 200 milliseconds off. An 1800 millisecond pause occurs before changing indicators. If the current value is zero, the appropriate Call Appearance Line indicator flutters five times 50 milliseconds on, 50 milliseconds off instead of winking.

50 4600 Series IP Telephone Release 2.2 Installation Guide